Integrated geoelectrical resistivity and hydrogeochemical methods for delineating and mapping heavy metal zone in aquifer system

A novel study on using geoelectrical resistivity, soil property, and hydrogeochemical analysis methods for delineating and mapping of heavy metal in aquifer system is presented in this paper. A total of 47 surveys of geoelectrical resistivity with Wenner configuration were conducted to determine the subsurface and the groundwater characteristics. The groundwater sample from 53 existing wells and 2 new wells has been analyzed to derive their water chemical content. The chemical analysis was done on the soil sample obtained from new two wells and from selected locations. The water and soil chemical analysis results from the new two wells were used as calibration in resistivity interpretation. The occurrence of heavy metal in aquifer system was expected to detect using the geoelectrical resistivity survey for the whole study area. The result of groundwater analysis shows that the groundwater sample contains a relatively low concentration of Fe (<?0.3 mg/L) elongating from the south up to the middle region. While in the middle and the northwestern, Fe concentration is relatively high (around 12 mg/L). Chemical analysis of soil sample shows that in the lower resistivity zone (<?18 Ωm), Al and Fe concentrations are comparatively high with an average of 68,000 and 40,000 mg/kg, respectively. Starting from the middle to the northwestern zone, the resistivity value appears to be low. It is definitely caused by higher Al and Fe concentration within the soil, and it is supported also by lower total anion content in the groundwater. While the resistivity value of more than 40 Ωm in aquifers is obtained in the zone which Fe concentration is relatively lower in the soil but not present in the groundwater. Correlation Fe concentration in the soil and Fe concentration in the groundwater sample shows the trend of positively linear; however, the Al concentration in soil has no correlation with Al content in groundwater. Finally, the probability of high heavy metal zone in the aquifer system is easily delineated by the distribution of geoelectrical resistivity presented in depth slice shapes which extend from the Boundary Range Composite Batholith in the north to the northwest.     

A knowledge-driven GIS modeling technique for groundwater potential mapping at the Upper Langat Basin, Malaysia

The aim of this paper is to use a knowledge-driven expert-based geographical information system (GIS) model coupling with remote-sensing-derived parameters for groundwater potential mapping in an area of the Upper Langat Basin, Malaysia. In this study, nine groundwater storage controlling parameters that affect groundwater occurrences are derived from remotely sensed imagery, available maps, and associated databases. Those parameters are: lithology, slope, lineament, land use, soil, rainfall, drainage density, elevation, and geomorphology. Then the parameter layers were integrated and modeled using a knowledge-driven GIS of weighted linear combination. The weightage and score for each parameter and their classes are based on the Malaysian groundwater expert opinion survey. The predicted groundwater potential map was classified into four distinct zones based on the classification scheme designed by Department of Minerals and Geoscience Malaysia (JMG). The results showed that about 17% of the study area falls under low-potential zone, with 66% on moderate-potential zone, 15% with high-potential zone, and only 0.45% falls under very-high-potential zone. The results obtained in this study were validated with the groundwater borehole wells data compiled by the JMG and showed 76% of prediction accuracy. In addition statistical analysis indicated that hard rock dominant of the study area is controlled by secondary porosity such as distance from lineament and density of lineament. There are high correlations between area percentage of predicted groundwater potential zones and groundwater well yield. Results obtained from this study can be useful for future planning of groundwater exploration, planning and development by related agencies in Malaysia which provide a rapid method and reduce cost as well as less time consuming. The results may be also transferable to other areas of similar hydrological characteristics.     

Comparison of recorded rainfall with quantitative precipitation forecast in a rainfall-runoff simulation for the Langat River Basin, Malaysia

Observed rainfall is used for runoff modeling in flood forecasting where possible, however in cases where the response time of the watershed is too short for flood warning activities, a deterministic quantitative precipitation forecast (QPF) can be used. This is based on a limited-area meteorological model and can provide a forecasting horizon in the order of six hours or less. This study applies the results of a previously developed QPF based on a 1D cloud model using hourly NOAA-AVHRR (Advanced Very High Resolution Radiometer) and GMS (Geostationary Meteorological Satellite) datasets. Rainfall intensity values in the range of 3–12 mm/hr were extracted from these datasets based on the relation between cloud top temperature (CTT), cloud reflectance (CTR) and cloud height (CTH) using defined thresholds. The QPF, prepared for the rainstorm event of 27 September to 8 October 2000 was tested for rainfall runoff on the Langat River Basin, Malaysia, using a suitable NAM rainfall-runoff model. The response of the basin both to the rainfall-runoff simulation using the QPF estimate and the recorded observed rainfall is compared here, based on their corresponding discharge hydrographs. The comparison of the QPF and recorded rainfall showed R² = 0.9028 for the entire basin. The runoff hydrograph for the recorded rainfall in the Kajang sub-catchment showed R² = 0.9263 between the observed and the simulated, while that of the QPF rainfall was R² = 0.819. This similarity in runoff suggests there is a high level of accuracy shown in the improved QPF, and that significant improvement of flood forecasting can be achieved through ‘Nowcasting’, thus increasing the response time for flood early warnings.     

Electrical imaging of the groundwater aquifer at Banting,Selangor, Malaysia

A geophysical study was carried out in the Banting area of Malaysia to delineate groundwater aquifer and marine clay layer of the alluvial Quaternary deposits of Beruas and Gula Formations. The Beruas Formation is formed by peat and clayey materials as well as silt and sands, whereas the Gula Formation consists of clay, silt, sand and gravels. Both Formations were deposited on top of the Carboniferous shale of the Kenny Hill Formation. A 2-D geoelectrical resistivity technique was used. Resistivity measurement was carried out using an ABEM SAS 4000 Terrameter. The 2-D resistivity data of subsurface material for each survey line was calculated through inverse modelling and then compared with borehole data. The resistivity images of all the subsurface material below the survey lines show similar pattern of continuous structure of layering or layers with some lenses with resistivity ranging from 0.1 to 50 Ωm. The upper layer shows resistivity values ranging from 0.1 to 10 Ωm, representing a clay horizon with a thickness up to 45 m. The second layer with depth varies from 45 to 70 m below surface and has resistivity values ranging from 10 to 30 Ωm. Borehole data indicate coarse sand with some gravels for this layer, which is also the groundwater aquifer in the study area. The lowermost layer at a depth of 70 m below ground level shows resistivity values ranging from 30–50 Ωm and can be correlated with metasedimentary rocks consisting of shale and metaquartzite.     

Evaluation of soil corrosivity and aquifer protective capacity using geoelectrical investigation in Bwari basement complex area,Abuja

Bwari is one of the six municipal area councils of the Federal Capital Territory (FCT), Abuja with its attendant growing population and infrastructural developments. Groundwater is the main source of water supply in the area, and urbanization and industrialization are the predominant contributors of contaminants to the hydrological systems. In order to guarantee a continuous supply of potable water, there is a need to investigate the vulnerability of the aquifers to contaminants emanating from domestic and industrial wastes. A total of 20 vertical electrical soundings using Schlumberger electrode array with a maximum half current electrodes separation of 300 m was employed. The results show that the area is characterized by 3–6 geoelectric subsurface layers. The measured overburden thickness ranges from 1.0 to 24.3 m, with a mean value of 7.4 m. The resistivity and longitudinal conductance of the overburden units range from 18 to 11,908 Ωm and 0.047 to 0.875 mhos, respectively. Areas considered as high corrosivity are the central parts with ρ < 180 Ωm. The characteristic longitudinal unit conductance was used to classify the area into zones of good (0.7–4.49 mhos), moderate (0.2–0.69 mhos), weak (0.1–0.19 mhos), and poor (<0.1) aquifer protective capacity. Zones characterized by materials of moderate to good protective capacity serve as sealing potential for the underlying hydrogeological system in the area. This study is aimed at delineating zones that are very prone to groundwater contamination from surface contaminants and subsurface soils that are corrosive to utility pipes buried underground. Hence the findings of this work will constitute part of the tools for groundwater development and management and structural/infrastructural development planning of the area.     

Hydrogeochemistry and groundwater quality assessment of the multilayered aquifer in Lower Kelantan Basin,Kelantan, Malaysia

Continual expansion of population density, urbanization, agriculture, and industry in most parts of the world has increased the generation of pollution, which contributes to the deterioration of surface water quality. This causes the dependence on groundwater sources for their daily needs to accumulate day by day, which raises concerns about their quality and hydrogeochemistry. This study was carried out to increase understanding of the geological setup and assess the groundwater hydrogeochemical characteristics of the multilayered aquifers in Lower Kelantan Basin. Based on lithological data correlation of exploration wells, the study area can be divided into three main aquifers: shallow, intermediate and deep aquifers. From these three aquifers, 101 groundwater samples were collected and analyzed for various parameters. The results showed that pH values in the shallow, intermediate and deep aquifers were generally acidic to slightly alkaline. The sequences of major cations and anions were Na⁺ > Ca²⁺ > Mg²⁺ > K⁺ and HCO₃^? > Cl^? > SO₄^2? > CO₃^2?, respectively. In the intermediate aquifer, the influence of ancient seawater was the primary factor that contributed to the elevated values of electrical conductivity (EC), Cl^? and total dissolved solids (TDS). The main facies in the shallow aquifer were Ca–HCO₃ and Na–HCO₃ water types. The water types were dominated by Na–Cl and Na–HCO₃ in the intermediate aquifer and by Na–HCO₃ in the deep aquifer. The Gibbs diagram reveals that the majority of groundwater samples belonged to the deep aquifer and fell in the rock dominance zone. Shallow aquifer samples mostly fell in the rainfall zone, suggesting that this aquifer is affected by anthropogenic activities. In contrast, the results suggest that the deep aquifer is heavily influenced by natural processes.     

Integrated geoelectrical resistivity,hydrochemical and soil property analysis methods to study shallow groundwater in the agriculture area,Machang, Malaysia

Integrated geoelectrical resistivity, hydrochemical and soil property analysis methods were used to study the groundwater characteristics of sandy soils within a shallow aquifer in the agriculture area, Machang. A pilot test investigation was done prior to the main investigation. The area was divided into two sites. Test-Site 1 is non-fertilized; Test-Site 2 is the former regularly fertilized site. From the surface to depths of 75 cm, a lower average resistivity was obtained in Test-Site 2 (around 0.37 less than in Test-Site 1). The presence of nitrate and chloride contents in pore water reduced the resistivity values despite the low moisture content. The pH values for the whole area range from 4.11 to 6.88, indicating that the groundwater is moderately to slightly acidic. In the southern region, concentration of nitrate is considered to be high (>20 mg/l), while it is nearly zero in the northern region. In the south, the soil properties are similar. However, the geoelectrical model shows lower resistivity values (around 18 Ω m) at the sites with relatively high nitrate concentration in the groundwater (>20 mg/l). Conversely, the sites with low nitrate concentration reveal the resistivity values to be higher (>35 Ω m). Basement and groundwater potential maps are generated from the interpolation of an interpreted resistivity model. The areas that possibly have nitrate-contaminated groundwater have been mapped along with groundwater flow patterns. The northern part of the area has an east to west groundwater flow pattern, making it impossible for contaminated water from the southern region to enter, despite the northern area having a lower elevation.     

Phytoplankton community composition and size distribution in the Langat River estuary,Malaysia

Phytoplankton patchiness, as expressed by community composition and size distribution, during the rainy season in the Langat River estuary (Malaysia) is described. Four sites in the estuary were sampled on two different occasions. The sampling area covered a stretch of the river from upstream to downstream of aquaculture activities (shrimp farms). Water samples from a shrimp farm outlet were also analyzed for nutrient and phytoplankton content. Differences in community structure between stations were found by means of multivariate procedures. Genera composition and total biomass were related to environmental factors, revealing salinity, light, and nutrients as important explaining factors. Elevated phytoplankton biomass and total phosphorus concentration, as well as lower inorganic nitrogen: phosphorus ratios, were found downstream of the shrimp farming activities. The size distribution spectrum of the phytoplankton population downstream of the shrimp farms was significantly different from that at the other stations but not different than that found in the sampled effluent from the shrimp farms, where phytoplankton biomass was also high. Twenty-two of the 24 recorded genera from the shrimp farm outlet were also found downstream of the farming activities. A number of different environmental factors potentially alter conditions for phytoplankton in the lower reaches of the estuary as compared to the upper regions. A cause and effect relationship explaining the differences noted between the upper and lower reaches of the estuary cannot be established. This study suggests that nutrient enrichment from the shrimp farming activities is of a magnitude that may contribute to the phytoplankton community changes observed in the lower reaches of the estuary.     

Isotope Constraints on the Aquatic Carbon Budget: Langat Watershed,Malaysia

Langat River drains a tropical watershed in the southwest of the Malaysian Peninsula. The watershed is heavily urbanized in its downstream portion. Water samples were collected from May 2010 to December 2011, at three localities along the main stem river, 1 location at its Semenyih tributary and from an upstream groundwater source. Concentration and δ¹³C data of riverine DIC and DOC indicate the dominance of C3 plant-derived material as the primary source of carbon, with δ¹³C_DIC values enriched in ¹³C relative to that of the C3 source. This enrichment is likely due to CO₂ outgassing, as calculated concentrations of riverine CO₂ are significantly higher than ambient atmospheric values, with methanogenic activity a theoretically possible contributing factor, particularly at the upstream location. The Langat River therefore acts as a net source of CO₂, with a total sub-basin flux of 19.7 × 10³ t C year^?1. This is comparable to the sum of riverine DOC, DIC and POC loss rates from the sub-basin, calculated as 24.5 × 10³ t C year^?1, and highlights the significance of CO₂ evasion from water bodies to the atmosphere for balancing the budget of the terrestrial carbon cycle. The DIC and DOC concentration and δ¹³C data also suggests that in the more urbanized downriver areas, much of the organic carbon input may be anthropogenicaly derived due to ubiquity of sewage treatment plants and landfill sites. Such human-induced perturbations to riverine carbon cycling should be taken into account in future studies of urbanized watersheds.     

Salinity mapping of coastal groundwater aquifers using hydrogeochemical and geophysical methods: a case study from north Kelantan,Malaysia

Integrated hydrogeochemical and geophysical methods were used to study the salinity of groundwater aquifers along the coastal area of north Kelantan. For the hydrogeochemical investigation, analysis of major ion contents of the groundwater was conducted, and other chemical parameters such as pH and total dissolved solids were also determined. For the geophysical study, both geoelectrical resistivity soundings and reflection seismic surveys were conducted to determine the characteristics of the subsurface and groundwater contained within the aquifers. The pH values range from 6.2 to 6.8, indicating that the groundwater in the study area is slightly acidic. Low content of chloride suggests that the groundwater in the first aquifer is fresh, with an average concentration of about 15.8 mg/l and high geoelectrical resistivity (>45 ohm m). On the other hand, the groundwater in the second aquifer is brackish, with chloride concentration ranging from 500 mg/l to 3,600 mg/l and very low geoelectrical resistivity (<45 ohm m) as well as high concentration of total dissolved solids (>1,000 mg/l). The groundwater in the third aquifer is fresh, with chloride concentrations generally ranging from 2 mg/l to 210 mg/l and geoelectrical resistivity of greater than 45 ohm m. Fresh and saltwater interface in the first aquifer is generally located directly in the area of the coast, but, for the second aquifer, both hydrogeochemical and geoelectrical resistivity results indicate that the fresh water and saltwater interface is located as far as 6 km from the beach. The considerable chloride ion content initially suggests that the salinity of the groundwater in the second aquifer is probably caused by the intrusion of seawater. However, continuous monitoring of the chloride content of the second aquifer indicated no significant changes with time, from which it can be inferred that the salinity of the groundwater is not affected by seasonal seawater intrusion. Schoeller diagrams illustrate that sulphate concentrations of the groundwater of the second aquifer are relatively low compared to those of the recent seawater. Therefore, this result suggests that the brackish water in the second aquifer is probably from ancient seawater that was trapped within the sediments for a long period of time, rather than due to direct seawater intrusion.     

Integrated geoelectrical survey for groundwater and shallow subsurface evaluation: case study at Siliyin spring, El-Fayoum, Egypt

Siliyin spring is one of the many natural fresh water springs in the Western Desert of Egypt. It is located at the central part of El-Fayoum Delta, which is a potential place for urban developments and touristic activities. Integrated geoelectrical survey was conducted to facilitate mapping the groundwater resources and the shallow subsurface structures in the area. Twenty-eight transient electromagnetic (TEM) soundings, three vertical electrical soundings (VES) and three electrical resistivity tomography (ERT) profiles were carried out around the Siliyin spring location. The dense cultivation, the rugged topography and the existence of infra structure in the area hindered acquiring more data. The TEM data were inverted jointly with the VES and ERT, and constrained by available geological information. Based on the inversion results, a set of geoelectrical cross-sections have been constructed. The shallow sand to sandy clay layer that forms the shallow aquifer has been completely mapped underneath and around the spring area. Flowing of water from the Siliyin spring is interconnected with the lateral lithological changes from clay to sand soil. Exploration of the extension of Siliyin spring zone is recommended. The interpretation emphasizes the importance of integrating the geoelectrical survey with the available geological information to obtain useful, cheap and fast lithological and structural subsurface information.     

Investigation of the hydrogeochemical processes in an alluvial channel aquifer located in a typical Karoo Basin of Southern Africa

An investigation was conducted to assess the hydrogeochemical processes of an alluvial channel aquifer located in a typical Karoo Basin of Southern Africa. The investigation was aimed at identifying and describing the groundwater chemistry evolution and its contribution to the overall groundwater quality. X-ray fluorescent spectrometry (XRF) and X-ray diffractometry (XRD) analyses were performed on geological samples to identify and quantify the major element oxides and minerals. The study utilises the conventional Piper diagram, bivariate plots and PHREEQC hydrogeochemical model to analyse groundwater chemistry data obtained during the wet (February and May) and dry seasons (August and December) of 2011. The XRF and XRD results show that the channel deposits are dominated by SiO₂ element oxides and quartz minerals, thus elevated concentrations of silicon (Si⁴⁺) were found in the groundwater. Dolomite and calcite minerals were also detected in the unconsolidated aquifer sediments. The detailed study of the alluvial aquifer system has shown that dissolution of dolomite and calcite minerals and ion exchange are the dominant hydrogeochemical processes influencing the groundwater quality. The groundwater evolves from Ca²⁺–Mg²⁺–HCO₃ ^? recharge water that goes through ion exchange with Na⁺ in the clay-silt sediment to give a Na⁺–HCO₃ ^? water type. The groundwater is supersaturated with respect to quartz, dolomite and calcite minerals. The study shows the potential usefulness of simple bivariate plots as a complimentary tool to the conventional methods for analyzing groundwater hydrogeochemical processes.     

Groundwater recharge,flow and hydrogeochemical evolution in a complex volcanic aquifer system,central Ethiopia

Hydrochemical, multivariate statistical and inverse hydrogeochemical modeling techniques were used to investigate groundwater recharge, flow and the hydrochemical evolution within the Akaki volcanic aquifer system, central Ethiopia. The hydrochemical and multivariate statistical techniques are mutually supportive and the extracted information was analyzed together with environmental isotope data. Results reveal five spatial groundwater zones with defined hydrochemical facies, residence times, stable isotopic signals and hydrochemical evolution. These zones are designated as the (1) Intoto, (2) central, (3) Filwuha fault, (4) south zones and (5) a highly polluted sub-sector identified within the central zone. Both the hydrochemical and multivariate statistical analyses have shown the central sub-sector as being spite of differentially polluted by , Cl⁻ and and its tritium content shows recent recharge. Due to the fact that the main recharge source is precipitation, the hydrochemical and environmental isotope data clearly indicated that the central and southern sectors are also recharged from domestic waste water and leakage from water mains and reservoirs. Inverse hydrogeochemical modeling demonstrated reactions of silicate minerals in a CO₂ open system and precipitation of kaolinite, chalcedony, and rare calcite satisfy the observed change in water chemistry from north to south following the regional flow direction.

---

Electronic supplementary material The online version of this article (doi:) contains supplementary material, which is available to authorized users.

---

Résumé Des techniques relevant de l’hydrochimie, des statistiques multivariées et de la modélisation inverse hydrogéochimique, ont été utilisées dans le cadre de l’étude de la recharge des eaux souterraines, de l’écoulement et de l’évolution hydrochimique dans le système volcanique aquifère d’Akaki au centre de l’Ethiopie. Les techniques hydrochimiques et multivariées se supportent mutuellement et l’information extraite a été analysée avec les données isotopiques environnementales, des temps de résidence, des signaux isotopiques stables et une évolution hydrochimique. Ces zones ont été désignées comme le (1) Intoto, (2) le centre, (3) la faille de Filwuha, (4) les zones sud et (5) un sous-secteur fortement pollué identifié dans la zone centrale. Les analyses statistiques hydrochimiques et multivariées ont montré que le sous-secteur central a été différemment pollué par , Cl⁻ et , tandis que la teneur en tritium montre une recharge récente. Malgré le fait que la principale source de recharge soit les précipitations, les données hydrochimiques et isotopiques indiquent clairement que les secteurs centres et sud sont également rechargés par les eaux usées domestiques et les fuites de réservoirs et canalisations d’eau. La modélisation hydrogéochimique inverse a démontré les réactions des minéraux silicatés dans un système ouvert au CO₂, et la précipitation de kaolinite, de calcédoine, et la rareté de la calcite satisfont les changements observés dans la chimie de l’eau du nord vers le sud en suivant la direction régionale de l’écoulement.

---

Resumen Se utilizaron la hidroquímica y técnicas de modelación hidrogeoquímica inversa y estadística multivariada, para investigar la recarga del agua subterránea, el flujo y la evolución hidroquímica, dentro del sistema acuífero volcánico Akaki, Etiopía Central. La hidroquímica y las técnicas estadísticas multivariadas se complementan entre si y la información así extraída se analizó junto con los datos de isótopos ambientales. Los resultados revelan cinco zonas diferentes de agua subterránea, con facies hidroquímicas, tiempos de residencia, improntas isotópicas estables y una evolución hidroquímica definidas. Estas zonas se designan como (1) Intoto, (2) Central, (3) Falla de Filwuha, (4) las Zonas del sur y (5) un sub-sector altamente contaminado identificado dentro de la zona central. Tanto los análisis estadísticos multivariados como la hidroquímica, han mostrado al sub-sector central como contaminado diferencialmente por , Cl⁻ y y su contenido de tritio muestra una recarga reciente. A pesar del hecho que la fuente principal de recarga es la precipitación, los datos de hidroquímica y de isótopos ambientales indican que los sectores central y del sur, también se recargan a partir de agua doméstica usada y del goteo de las conducciones del acueducto y de sus reservorios. El modelamiento hidrogeoquímico inverso demostró reacciones de minerales silicatados en un sistema de CO₂ abierto, y la precipitación de caolinita, calcedonia, y rara vez de calcita, satisfacen el cambio observado en la química de agua del norte a sur, siguiendo la dirección del flujo regional.

     

Groundwater solute chemistry,hydrogeochemical processes and fluoride contamination in phreatic aquifer of Odisha,India

The work investigates the major solute chemistry of groundwater and fluoride enrichment(F~-) in the shallow phreatic aquifer of Odisha.The study also interprets the hydrogeochemical processes of solute acquisition and the genetic behavior of groundwater F~-contamination.A total of 1105 groundwater samples collected from across the state from different hydro-geomorphic settings have been analyzed for the major solutes and F~-content.Groundwater is alkaline in nature(range of pH: 6.6–8.7; ave.: 7.9) predominated by moderately hard to very hard types.Average cation and anion chemistry stand in the orders of Ca~(2+) Na~+ Mg~(2+) K~+and HCO_3~- Cl~- SO_4~(2-) CO_3~(2-)respectively.The average mineralization is low(319 mg/L).The primary water types are Ca-Mg-HCO_3 and Ca-Mg-Cl~-HCO_3, followed by Na-Cl, Ca-Mg-Cl, and Na-Ca-Mg-HCO_3~-Cl.Silicate-halite dissolution and reverse ion exchange are the significant processes of solute acquisition.Both the geogenic as well as the anthropogenic sources contribute to the groundwater fluoride contamination,etc.The ratio of Na~+/Ca~(2+) 1.0 comprises Na-HCO_3(Cl) water types with F~- 1.0 mg/L(range 1.0–3.5 mg/L)where the F~-bears geogenic source.Positive relations exist between F~-and pH, Na~+, TDS, and HCO_3~-.It also reflects a perfect Na-TDS correlation(0.85).The ratio of Na~+/Ca~(2+) 1.0 segregates the sample population(F~- range: 1.0–4.0 mg/L) with the F derived from anthropogenic sources.Such water types include Ca-Mg-HCO_3(Cl) varieties which are recently recharged meteoritic water types.The F~-levels exhibit poor and negative correlations with the solutes in groundwater.The Na-TDS relation remains poor(0.12).In contrast, the TDS levels show strong correlations with Ca~(2+)(0.91), Mg~(2+)(0.80) and even Cl~-(0.91).The majority of the monitoring points with the anthropogenic sources of groundwater F~-are clustered in the Hirakud Canal Command area in the western parts of the state, indicating the role of irrigation return flow in the F~-contamination.     

Elemental hydrochemistry assessment on its variation and quality status in Langat River, Western Peninsular Malaysia

This paper discusses the hydrochemistry variation and its quality status in Langat River, based on the chemistry of major ions, metal concentrations and suitability for drinking purposes. Water samples were collected from 30 different stations to assess their hydrochemical characteristics. The physico-chemical parameters selected were temperature, electrical conductivity, total dissolved solids (TDS), salinity, dissolved oxygen , pH, redox potential, HCO₃, Cl, SO₄, NO₃, Ca, Na, K, Mg, ²⁷Al, ¹³⁸Ba, ⁹Be, ¹¹¹Cd, ⁵⁹Co, ⁶³Cu, ⁵²Cr, ⁵⁷Fe, ⁵⁵Mn, ⁶⁰Ni, ²⁰⁸Pb, ⁸⁰Se and ⁶⁶Zn to investigate the variation of the constituents in the river water. Most of the parameters comply with the Drinking Water Quality Standard of the World Health Organization and the Malaysian National Standard for Drinking Water Quality by the Malaysia Ministry of Health except for EC, TDS, Cl, HCO₃, SO₄, Na, Mg, Al, Fe and Se. The results show that the Langat River is unsuitable for drinking purposes directly without treatment.     

Landslide hazard mapping at Selangor, Malaysia using frequency ratio and logistic regression models

The aim of this study is to evaluate the landslide hazards at Selangor area, Malaysia, using Geographic Information System (GIS) and Remote Sensing. Landslide locations of the study area were identified from aerial photograph interpretation and field survey. Topographical maps, geological data, and satellite images were collected, processed, and constructed into a spatial database in a GIS platform. The factors chosen that influence landslide occurrence were: slope, aspect, curvature, distance from drainage, lithology, distance from lineaments, land cover, vegetation index, and precipitation distribution. Landslide hazardous areas were analyzed and mapped using the landslide-occurrence factors by frequency ratio and logistic regression models. The results of the analysis were verified using the landslide location data and compared with probability model. The comparison results showed that the frequency ratio model (accuracy is 93.04%) is better in prediction than logistic regression (accuracy is 90.34%) model.