微波消解-石墨炉原子吸收光谱法测定痕量银的研究

传统的应用石墨炉原子吸收光谱法测定化探样品中的痕量银,一般采用盐酸-硝酸-氢氟酸-高氯酸电热板加热溶样,使用铱、铂为基体改进剂,但存在分析流程繁琐、成本高等缺点。相比于电热板消解法,微波消解技术的高压密闭消解和微波快速加热等特点,具有酸用量少、消解完全、消解过程损失少等优点。本文对传统的微波消解和仪器工作参数进行了改良,确定了最佳测定条件。建立了HNO_3-H_2O_2高压密闭消解样品,石墨炉原子吸收法测定水系沉积物、土壤、岩石中痕量银的方法。采用65%的HNO_3和H_2O_2微波消解溶样,加入12 g/L硫脲为介质,消除了基体干扰。方法检出限为0.018μg/g,将所建立的分析方法用于沉积物标准物质(GBW07309、GBW07311)、土壤标准物质(GBW07402、GBW07404)和岩石标准物质(GBW07103、GBW07104)验证,结果显示测定值与推荐值吻合,准确度△lg C(GBW)≤±0.024、RE(GBW)≤±5.71%,精密度RSD(GBW)≤5.97%。该分析方法适用于大批化探样品中痕量银的测定。     

石墨炉原子吸收光谱法测定地质样品中的痕量铂、钯

本文提出了用717阴离子交换树脂富集铂、钯的石墨炉原子吸收光谱分析方法。对富集铂、钯的条件,共存离子的干扰情况以及在GF-2000型石墨炉中测定铂、钯的最佳条件进行了研究。样品用王水分解后,在10％的王水介质中,用717阴离子交换树脂富集铂、钯,以热的硫脲溶液解脱,在拟定的工作条件下,于石墨炉原子吸收光谱仪上进行测定,大量的共存离子不干扰测定。方法简便快速,检出限分别为Pt8.8×10~(-9)g/ml,Pd3.4×10~(-9)g/ml,方法的相对标准偏差分别为Pt7.09％Pd11.48％,适用于地质样品中铂、钯的测定,结果令人满意。     

平台石墨炉原子吸收光谱法直接测定有机体中的痕量铅

本文提出了有机体消解方法,采用平台石墨炉原子吸收光谱法,结合稳定温度平台石墨炉技术,直接测定有机体中的痕量铅,方法检出限为３．８μｇ／Ｌ,回收率在９３％￣１０５％,ＲＳＤ（ｎ＝１０）为２．５％￣７．５％。     

氯化钯作基体改进剂石墨炉原子吸收光谱法测定土壤中的铍

铍是一种对人体有害的金属元素,土壤中铍的测定目前尚无国家标准方法.本文采用盐酸-硝酸-氢氟酸体系微波消解、石墨炉原子吸收光谱法测定土壤样品中的铍,实验了钯、硝酸铝、硝酸镁、钙盐的增敏效果.结果表明,以氯化钯为基体改进剂,灰化温度和原子化温度分别提高到1100℃和2650℃,原子化峰形尖锐,背景吸收很小,提高了测定灵敏度;其他三种基体改进剂虽然也能提高测定灵敏度,但背景吸收较大.采用优化的实验条件,Fe、Mg、K、Na、Ca、Ti、Cu、Ba、Mn、Zn、Pb、Sr等共存元素对测定不产生干扰.铍的浓度在0 ～4.00 μg/L范围内线性良好,方法检出限为0.01 μg/g,精密度(RSD,n=6)为3.5％ ～6.7％,实际土壤样品的加标回收率为84.0％ ～ 113.0％,土壤国家标准物质的测定值在标准值的误差范围内.本法与萃取光度法、电感耦合等离子体发射光谱/质谱法相比,操作简便,分析成本较低.     

快速程序升温-石墨炉原子吸收光谱法测定地质样品中痕量镉

建立了快速程序升温-石墨炉原子吸收光谱测定地质样品中痕量镉的分析方法.样品用硝酸-氢氟酸-高氯酸进行前处理,为提高分析效率,改进了石墨炉升温程序,省去了常规方法中的灰化步骤,使测定镉的程序升温时间由常规的90～100 s降至24 s,工作效率显著提高.方法检出限为0.011 μg/g,加标回收率为93.5%～106.0...     

悬浮液进样石墨炉原子吸收光谱法测定环境样品中痕量铅

提出了悬浮液进样石墨炉原子吸收光谱法测定环境样品中痕量铅的分析方法.讨论了悬浮颗粒粒径、悬浮液浓度、悬浮稳定剂、基体改进剂等因素对测定结果的影响.实验结果表明: 样品粒径 < 38μm, 以0.2g/L的Triton - 100为悬浮剂, 3g/L的(NH₄)₂HPO₄为基体改进剂, 电磁搅拌进样可简便快速地测定地质样品中的痕量铅, 方法的检出限为0.10ng/g, 精密度为3.31% (n =10).43GSD标样测定结果与推荐值一致      

GFAAS法测定地质样品中痕量银

采用石墨炉原子吸收光谱法测定化探样品中痕量银。选择仪器最佳温度程序,采用四酸溶样,硝酸介质,硫脲、铱盐为基体改进剂,国家一级标准样品绘制工作曲线。在取样0．1000g,定容10mL情况下,方法检出限为0．01ug／g,经用国家标准物质验证,测定准确度和精密度比较满意。     

高压消解-石墨炉原子吸收测定近海生物样品中的铅、镉

采用高压消解-石墨炉原子吸收测定近海生物样品中的铅、镉,探讨了硝酸+过氧化氢不同配比,消解时间的选择,以及准确度、精密度和检出限试验。通过对国家一级标准物质及实际样品进行方法验证,结果表明该分析方法的准确度好,精密度高,检出限达到规范要求,实际样品加标回收率在90%~105%,测试结果准确可靠,能满足近海生物样品的测试要求。     

悬浮液进样—石墨炉原子吸收光谱法测定琥珀中微量铅

报道了以NH4H2PO4为基体改进剂，采用悬浮体制样石墨炉原子吸收光谱法直接测定琥珀中微量铅的方法。试验了影响测定的主要因素。在优化实验条件下。方法的检出限为0．038μg／g，Pb的质量浓度为0～80μg／L时，工作曲线线性关系良好。对于ω(Pb)=5．71μg／g样品的测定，相对标准偏差(RSD，n=5)为6．83％。     

微波消解等离子体发射光谱和石墨炉原子吸收光谱法联合测定土壤中多元素

采用密闭式微波消解系统处理土壤样品,电感耦合等离子体发射光谱法或石墨炉原子吸收光谱法测定土壤样品中铜、砷、铅、锌、钴、铬、锰、镍、钒9个元素。分别从消解液的选择、用酸量及样品消解量等方面进行消解条件的优化,确定了一个最适合土壤消解的前处理体系。各元素的检出限为0.16～2.52μg/g,回收率为95.2%～106.6%,精密度为2.03%～9.79%(n=7)。方法简单快速,效率高,劳动强度低,是进行土壤中多元素测定的高效方法。     

The terrestrial fauna of the Late Triassic Pant-y-ffynnon Quarry fissures,South Wales,UK and a new species of Clevosaurus (Lepidosauria: Rhynchocephalia)

Pant-y-ffynnon Quarry in South Wales yielded a rich cache of fossils in the early 1950s, including articulated specimens of new species (the small sauropodomorph dinosaur Pantydraco caducus and the crocodylomorph Terrestrisuchus gracilis), but no substantial study of the wider fauna of the Pant-y-ffynnon fissure systems has been published. Here, our overview of existing specimens, a few described but mostly undescribed, as well as freshly processed material, provides a comprehensive picture of the Pant-y-ffynnon palaeo-island of the Late Triassic. This was an island with a relatively impoverished fauna dominated by small clevosaurs (rhynchocephalians), including a new species, Clevosaurus cambrica, described here from a partially articulated specimen and isolated bones. The new species has a dental morphology that is intermediate between the Late Triassic Clevosaurus hudsoni, from Cromhall Quarry to the east, and the younger C. convallis from Pant Quarry to the west, suggesting adaptive radiation of clevosaurs in the palaeo-archipelago. The larger reptiles on the palaeo-island do not exceed 1.5?m in length, including a small carnivorous crocodylomorph, Terrestrisuchus, and a possible example of insular dwarfism in the basal dinosaur Pantydraco.     

Définition d'une limite multicritère ; stratigraphie du passage Campanien–Maastrichtien du site géologique de Tercis (Landes,SW France)Definition of a multi-criteria boundary; stratigraphy of the Campanian–Maastrichtian interval of the geological site at Tercis (Landes,SW France)

Lithostratigraphy, physicochemical stratigraphy, biostratigraphy, and geochronology of the 77–70 Ma old series bracketing the Campanian–Maastrichtian boundary have been investigated by 70 experts. For the first time, direct relationships between macro- and microfossils have been established, as well as direct and indirect relationships between chemo-physical and biostratigraphical tools. A combination of criteria for selecting the boundary level, duration estimates, uncertainties on durations and on the location of biohorizons have been considered; new chronostratigraphic units are proposed. The geological site at Tercis is accepted by the Commission on Stratigraphy as the international reference for the stratigraphy of the studied interval. To cite this article: G.S. Odin, C. R. Geoscience 334 (2002) 409–414.     

The effect of water on accessory phase solubility in subaluminous and peralkaline granitic melts

The solubilities of columbite, tantalite, wolframite, rutile, zircon and hafnon were determined as a function of the water contents in peralkaline and subaluminous granite melts. All experiments were conducted at 1035 °C and 2 kbar and the water contents of the melts ranged from nominally dry to approximately 6 wt.% H₂O. Accessory phase solubilities are not affected by the water content of the peralkaline melt. By contrast, solubilities are affected by the water content of the subaluminous melt, where the solubilities of all the accessory phases examined increase with the water content of the melt, up to 2 wt.% H₂O. At higher water contents, solubilities are nearly constant. It can be concluded that water is not an important control of accessory phase solubility, although the water content will affect diffusivities of components in the melt, thus whether or not accessory phases will be present as restite material. The solubility behaviour in the subaluminous and peralkaline melts supports previous spectroscopic studies, which have observed differences in the coordination of high field strength elements in dry vs. wet subaluminous granitic glasses, but not for peralkaline granitic glasses. Lastly, the fact that wolframite solubility increases with increasing water content in the subaluminous melt suggests that tungsten dissolved as a hexavalent species.     

Quaternary stresses revealed by calcite twinning inversion: insights from observations in the Savonnières underground quarry (eastern France)

Calcite samples were extracted both from the rock matrix and the superficial coating of a karstified fault plane of an underground quarry, located in the eastern border of the Paris basin. The karstification is dated as Quaternary. Analysis of mechanical calcite twinning reveals that only the calcite matrix has also undergone a compression trending WNW that can be attributed to the Mio-Pliocene alpine collision. Both coating and matrix have undergone a strike-slip regime with σ₁ roughly trending north–south, that could correspond to the regional present-day state of stress, a strike-slip compression rather trending NNW, modified by local phenomena. To cite this article: M. Rocher et al., C. R. Geoscience 335 (2003).     

NONMETALS DEPOSITS

正20141520 Bo Ying(Key Laboratory of Metallogeny and Mineral Assessment,MLR,Beijing 100037,China);Liu Chenglin Saline Spring Hydrochemical Characteristics and Indicators for Potassium Exploration in Southwestern and Northern Tarim Basin,Xinjiang(Acta Geoscientica Sinica,ISSN1006-3021,CN11-3474/P,34(5),2013,p.594-602,5 illus.,3 tables,28 refs.)     

MATHEMATICAL GEOLOGY

正20141243Chen Ge(Hangzhou Research Institute of Petroleum Geology,PetroChina,Hangzhou 310023,China);Si Chunsong Study on Sedimentary Numerical Simulation Method of Fan Delta Sand Body(Journal of Geology,     

PROSPECTING EXPLORATION

正20142599Chen Sanming(Guangxi Key Laboratory of Concealed Deposits Exploration,Guilin University of Technology,Guilin541004,China);He Yuzhou Block Model and Reserves Estimation of Panzhihua Iron Deposit Based on 3D Geological Modeling(Journal of Guilin University of Technology,ISSN1674-9057,CN45-1375/N,33(4),2013,p.610-615,9illus.,1table,15refs.)     

STRUCTURAL GEOLOGY

正20140594 Bai Daoyuan(Hunan Institute of Geology Survey,Changsha 410016,China);Zhong Xiang Faults in the Jingzhou Basin and Their Tectonic Settings(Geotectonica et Metallogenia,ISSN1001-1552,CN44-1595/P,37(2),2013,p.173-183,6illus.,59refs.)Key words:basin evolution,tectonic setting,South China In the Upper Paleozoic and Jurassic se-     

STRUCTURAL GEOLOGY

正20141912Cao Hui(State Key Laboratory for Continental Tectonics and Dynamics,Institute of Geology,Chinese Academy of Geological Sciences,Beijing 100037,China)Gravitational Collapse and Folding during Orogenesis:A Comparative Study of FIA Trends and Fold Axial Plane Traces(Geology in China,ISSN1000-3657,CN11-1167/P,40(6),2013,p.1818-1828,9illus.,35refs.,with