Probabilistic seismic hazard analysis for Bangalore

This article presents the results of probabilistic seismic hazard analysis (PSHA) for Bangalore, South India. Analyses have been carried out considering the seismotectonic parameters of the region covering a radius of 350 km keeping Bangalore as the center. Seismic hazard parameter ‘b’ has been evaluated considering the available earthquake data using (1) Gutenberg–Richter (G–R) relationship and (2) Kijko and Sellevoll (1989, 1992) method utilizing extreme and complete catalogs. The ‘b’ parameter was estimated to be 0.62 to 0.98 from G–R relation and 0.87 ± 0.03 from Kijko and Sellevoll method. The results obtained are a little higher than the ‘b’ values published earlier for southern India. Further, probabilistic seismic hazard analysis for Bangalore region has been carried out considering six seismogenic sources. From the analysis, mean annual rate of exceedance and cumulative probability hazard curve for peak ground acceleration (PGA) and spectral acceleration (Sa) have been generated. The quantified hazard values in terms of the rock level peak ground acceleration (PGA) are mapped for 10% probability of exceedance in 50 years on a grid size of 0.5 km × 0.5 km. In addition, Uniform Hazard Response Spectrum (UHRS) at rock level is also developed for the 5% damping corresponding to 10% probability of exceedance in 50 years. The peak ground acceleration (PGA) value of 0.121 g obtained from the present investigation is slightly lower (but comparable) than the PGA values obtained from the deterministic seismic hazard analysis (DSHA) for the same area. However, the PGA value obtained in the current investigation is higher than PGA values reported in the global seismic hazard assessment program (GSHAP) maps of Bhatia et al. (1999) for the shield area.     

Probabilistic seismic hazard at the archaeological site of Gol Gumbaz in Vijayapura,south India

Probabilistic seismic hazard analysis (PSHA) is carried out for the archaeological site of Vijayapura in south India in order to obtain hazard consistent seismic input ground-motions for seismic risk assessment and design of seismic protection measures for monuments, where warranted. For this purpose the standard Cornell-McGuire approach, based on seismogenic zones with uniformly distributed seismicity is employed. The main features of this study are the usage of an updated and unified seismic catalogue based on moment magnitude, new seismogenic source models and recent ground motion prediction equations (GMPEs) in logic tree framework. Seismic hazard at the site is evaluated for level and rock site condition with 10% and 2% probabilities of exceedance in 50 years, and the corresponding peak ground accelerations (PGAs) are 0.074 and 0.142 g, respectively. In addition, the uniform hazard spectra (UHS) of the site are compared to the Indian code-defined spectrum. Comparisons are also made with results from National Disaster Management Authority (NDMA 2010), in terms of PGA and pseudo spectral accelerations (PSAs) at T = 0.2, 0.5, 1.0 and 1.25 s for 475- and 2475-yr return periods. Results of the present study are in good agreement with the PGA calculated from isoseismal map of the Killari earthquake, \({\hbox {M}}_{\mathrm{w}} = 6.4\) (1993). Disaggregation of PSHA results for the PGA and spectral acceleration (\({\hbox {S}}_{\mathrm{a}}\)) at 0.5 s, displays the controlling scenario earthquake for the study region as low to moderate magnitude with the source being at a short distance from the study site. Deterministic seismic hazard (DSHA) is also carried out by taking into account three scenario earthquakes. The UHS corresponding to 475-yr return period (RP) is used to define the target spectrum and accordingly, the spectrum-compatible natural accelerograms are selected from the suite of recorded accelerograms.     

Probabilistic seismic hazard analysis of Tripura and Mizoram states

A probabilistic seismic hazard analysis for the states of Tripura and Mizoram in North East India is presented in this paper to evaluate the ground motion at bedrock level. Analyses were performed considering the available earthquake catalogs collected from different sources since 1731–2010 within a distance of 500 km from the political boundaries of the states. Earthquake data were declustered to remove the foreshocks and aftershocks in time and space window and then statistical analysis was carried out for data completeness. Based on seismicity, tectonic features and fault rupture mechanism, this region was divided into six major seismogenic zones and subsequently seismicity parameters (a and b) were calculated using Gutenberg–Richter (G–R) relationship. Faults data were extracted from SEISAT (Seismotectonic atlas of India, Geological Survey of India, New Delhi, 2000) published by Geological Survey of India and also from satellite images. The study area was divided into small grids of size 0.05° × 0.05° (approximately 5 km × 5 km), and the hazard parameters (rock level peak horizontal acceleration and spectral accelerations) were calculated at the center of each of these grid cells considering all the seismic sources within a radius of 500 km. Probabilistic seismic hazard analyses were carried out for Tripura and Mizoram states using the predictive ground motion equations given by Atkinson and Boore (Bull Seismol Soc Am 93:1703–1729, 2003) and Gupta (Soil Dyn Earthq Eng 30:368–377, 2010) for subduction belt. Attenuation relations were validated with the observed PGA values. Results are presented in the form of hazard curve, peak ground acceleration (PGA) and uniform hazard spectra for Agartala and Aizawl city (respective capital cities of Tripura and Mizoram states). Spatial variation of PGA at bedrock level with 2 and 10 % probability of exceedance in 50 years has been presented in the paper.     

Probabilistic seismic hazard analysis of Kahramanmaras Province,Turkey

Kahramanmaras and its surroundings are under the influence of East Anatolian and Dead Sea fault zones which have significance in the tectonics of Turkey. The long-term energy accumulation in these zones creates a very high risk level in terms of seismic hazard. In this study, the seismic hazard of Kahramanmaras Province and its vicinity was tried to be determined by using the probabilistic seismic hazard method approach. The earthquake catalog used in the study comprises 424 earthquakes equal or greater than M _w ?=?4.0, covering a time period between 1 January 1900 and 1 January 2015. The earthquake data have been compiled from the catalogs of the International Seismological Center (ISC), Republic of Turkey Prime Ministry Disaster and Emergency Management Precidency (RTPMDEMP), Bogazici University Kandilli Observatory and Earthquake Research Institute. Seismic sources that could affect the study area have been identified according to the Earthquake Model of the Middle East (EMME). Seismic hazard parameters and peak horizontal acceleration values were obtained by using the selected attenuation relationships, and the results were given with iso-acceleration maps corresponding to a recurrence period of 475 years. The calculated peak horizontal acceleration values are generally varying between 0.21 and 0.41 in the study area. The result of this study shows that the southeastern parts of the study area have a greater seismic hazard compared with other parts.     

Probabilistic seismic hazard zonation of Syria

Earthquake hazard maps for Syria are presented in this paper. The Peak Ground Acceleration (PGA) and the Modified Mercalli Intensity (MMI) on bedrock, both with 90% probability of not being exceeded during a life time of 50, 100 and 200 years, respectively are developed. The probabilistic PGA and MMI values are evaluated assuming linear sources (faults) as potential sources of future earthquakes. A new attenuation relationship for this region is developed. Ten distinctive faults of potential earthquakes are identified in and around Syria. The pertinent parameters of each fault, such as theb-parameter in the Gutenberg-Richter formula, the annual rate ₄ and the upper bound magnitudem ₁ are determined from two sets of seismic data: the historical earthquakes and the instrumentally recorded earthquake data (AD 1900–1992). The seismic hazard maps developed are intended for preliminary analysis of new designs and seismic check of existing civil engineering structures.     

Probabilistic seismic hazard maps for Panama

Probabilistic seismic hazard maps in term of Modified Mercalli (MM) intensity are derived by applying the Cornell-McGuire method to four earthquake source zones in Panama and adjacent areas. The maps contain estimates of the maximum MM intensity for return periods of 5, 25 and 100 yr. The earthquake phenomenon is based on the point source model. The probabilistic iso-intensity map for a return period of 50 yr indicates that the Panama Suture Zone (PSZ) could experience a maximum (MM) intensity IX, and the Panama Fracture Zone (PFZ) an MM intensity VIII, for the rest of the area this varies from IV up to VIII. The present study intends to serve as a reference for more advanced approaches, to stimulate discussions and suggestions on the data base, assumptions and inputs, and path for the risk based assessment of the seismic hazard in the site selection and in the design of common buildings and engineering.     

Probabilistic seismic hazard evaluation in underground mines

Stress concentrations produced by rock deformation due to extraction in underground mines induce seismicity that can take the shape of violent and quite dangerous rockbursts.The hazard evaluation presented in this paper is based on a Bayesian probabilistic synthesis of information determined from mining situations during excavation, with previous and present data from microseismicity and seismoacustics.The method proposed in this study is an example of time-dependent on-line seismic hazard evaluation. All results presented were obtained retrospectiely for different underground coal mines in Poland and Czechoslovakia.On leave from Institute of Geophysics, Polish Academy of Sciences 01-452 Warszawa, ul. Ksiecia Janusza 64, Poland.     

Probabilistic seismic hazard analysis and spectral accelerations for United Arab Emirates

In recent years, the United Arab Emirates (UAE) has experienced an unprecedented growth which is coupled with the increase in seismic activity in the surroundings. Previous studies presents significant variations in their results whereas some recent studies although very detailed focus on only few cities. This study reviews the results of previous studies and presents new findings for the whole of UAE based on the improved source model and use of next generation attenuation (NGA) equations. The peak ground accelerations, spectral accelerations and deaggregation of hazard for major cities are presented. Moreover, the breakdown of the range of mapped spectral accelerations (S _0.2 and S ₁) is proposed to form the basis for the development of site amplification factors in subsequent studies. The results of this study indicate almost similar values of ground motion compared to some recently published studies and smaller values compared to some earlier studies.     

Probabilistic seismic hazard maps for the sultanate of Oman

This study presents the results of the first probabilistic seismic hazard assessment (PSHA) in the framework of logic tree for Oman. The earthquake catalogue was homogenized, declustered, and used to define seismotectonic source model that characterizes the seismicity of Oman. Two seismic source models were used in the current study; the first consists of 26 seismic source zones, while the second is expressing the alternative view that seismicity is uniform along the entire Makran and Zagros zones. The recurrence parameters for all the seismogenic zones were determined using the doubly bounded exponential distribution except the zones of Makran, which were modelled using the characteristic distribution. Maximum earthquakes were determined and the horizontal ground accelerations in terms of geometric mean were calculated using ground-motion prediction relationships developed based upon seismic data obtained from active tectonic environments similar to those surrounding Oman. The alternative seismotectonic source models, maximum magnitude, and ground-motion prediction relationships were weighted and used to account for the epistemic uncertainty. Hazard maps at rock sites were produced for 5?% damped spectral acceleration (SA) values at 0.1, 0.2, 0.3, 1.0 and 2.0?s spectral periods as well as peak ground acceleration (PGA) for return periods of 475 and 2,475?years. The highest hazard is found in Khasab City with maximum SA at 0.2?s spectral period reaching 243 and 397?cm/s² for return periods 475 and 2,475 years, respectively. The sensitivity analysis reveals that the choice of seismic source model and the ground-motion prediction equation influences the results most.     

Probabilistic seismic hazard assessment in the northeastern part of Algeria

This work involves updating the evaluation of seismic hazard in Northeast Algeria by a probabilistic approach. This reassessment attempts to resolve inconsistencies between seismic zoning in regional building codes and is further motivated by the need to refine the input data that are used to evaluate seismic hazard scenarios. We adopted a seismotectonic model that accounts for differences in interpretations of regional seismicity. We then performed a probabilistic assessment of regional seismic hazard in Northeast Algeria. Based on a homogeneous earthquake catalog and geological and seismotectonic data gathered in the first part of the study, a seismotectonic zoning map was created and seven risk areas were identified. For each area, peak ground acceleration hazard maps were produced. Details of the calculations are provided, including hazard curves at periods of 0.1, 0.2, 0.33, 0.5, 1.0, and 2.0 s and uniform hazard spectra at urban locations in the area, including Sétif, Constantine, Kherrata, Bejaia, and Jijel.     

Probabilistic assessment of seismic hazard of dam sites in Jordan

A Probabilistic method is used to evaluate the seismic hazard of nineteen embankment dam sites in Jordan. A line source model developed by McGuire (1978) is used in this study. An updated earthquake catalogue covering the period from 1 A.D. to 1991 A.D. is used for this purpose. This catalogue includes all earthquakes that occurred in Jordan and adjacent areas, more specifically between latitudes 27.0°–35.5° N and longitudes 32.0°–39.0° E.Nine distinct seismic sources of potential seismic activities are identified. The seismic hazard parameters are determined using the method suggested by Kijko and Sellevoll (1989).The Peak Ground Acceleration (PGA) is selected as a measure of ground motion severity. Esteva (1974) attenuation relationship is used in evaluating PGA values at each dam site. Analysis is carried out for 50%, 90%, and 95% probability that is not being exceeded in a life time of 50, 100, and 200 years.Results of analysis indicate that PGA values are higher for dam sites closer to the Dead Sea Fault. This fault is believed to be responsible for most earthquake activities in Jordan and vicinity. The highest PGA value is found to be for Al-Karama dam site.     

Probabilistic seismic hazard analysis for Sumatra, Indonesia and across the Southern Malaysian Peninsula

The ground motion hazard for Sumatra and the Malaysian peninsula is calculated in a probabilistic framework, using procedures developed for the US National Seismic Hazard Maps. We constructed regional earthquake source models and used standard published and modified attenuation equations to calculate peak ground acceleration at 2% and 10% probability of exceedance in 50 years for rock site conditions. We developed or modified earthquake catalogs and declustered these catalogs to include only independent earthquakes. The resulting catalogs were used to define four source zones that characterize earthquakes in four tectonic environments: subduction zone interface earthquakes, subduction zone deep intraslab earthquakes, strike-slip transform earthquakes, and intraplate earthquakes. The recurrence rates and sizes of historical earthquakes on known faults and across zones were also determined from this modified catalog. In addition to the source zones, our seismic source model considers two major faults that are known historically to generate large earthquakes: the Sumatran subduction zone and the Sumatran transform fault. Several published studies were used to describe earthquakes along these faults during historical and pre-historical time, as well as to identify segmentation models of faults. Peak horizontal ground accelerations were calculated using ground motion prediction relations that were developed from seismic data obtained from the crustal interplate environment, crustal intraplate environment, along the subduction zone interface, and from deep intraslab earthquakes. Most of these relations, however, have not been developed for large distances that are needed for calculating the hazard across the Malaysian peninsula, and none were developed for earthquake ground motions generated in an interplate tectonic environment that are propagated into an intraplate tectonic environment. For the interplate and intraplate crustal earthquakes, we have applied ground-motion prediction relations that are consistent with California (interplate) and India (intraplate) strong motion data that we collected for distances beyond 200 km. For the subduction zone equations, we recognized that the published relationships at large distances were not consistent with global earthquake data that we collected and modified the relations to be compatible with the global subduction zone ground motions. In this analysis, we have used alternative source and attenuation models and weighted them to account for our uncertainty in which model is most appropriate for Sumatra or for the Malaysian peninsula. The resulting peak horizontal ground accelerations for 2% probability of exceedance in 50 years range from over 100% g to about 10% g across Sumatra and generally less than 20% g across most of the Malaysian peninsula. The ground motions at 10% probability of exceedance in 50 years are typically about 60% of the ground motions derived for a hazard level at 2% probability of exceedance in 50 years. The largest contributors to hazard are from the Sumatran faults.     

Probabilistic seismic hazard analysis of interconnected infrastructure: a case of Iranian high-pressure gas supply system

Seismic hazard maps are widely used for engineering design, land-use planning, and disaster mitigation. The development of the new seismic hazard map of Iran with regard to the specification of Iranian high-pressure gas network is based on probabilistic seismic hazard analysis using the historical and new earthquakes data, geology, tectonics, fault activity, and seismic zone models in Iran. The map displays the probabilistic estimates of peak ground acceleration for the return period of 2,475 year (2 % probability in 50 years). The results presented in this study will provide the basis for the preparation of risk map, the estimation of insurance premiums, finding best paths for future pipelines, planning, and relocating lifeline facilities especially for interconnected infrastructures.     

Probabilistic seismic hazard of Pakistan, Azad-Jammu and Kashmir

The seismic hazard study for Pakistan and Azad Jammu and Kashmir has been conducted by using probabilistic approach in terms of peak ground acceleration (PGA) in m/s² and also seismic hazard response spectra for different cities. A new version of Ambraseys et al. (Bull Earthq Eng 3:1–53, 2005) ground acceleration model is used, and parameterization is based on most recent updated earthquake catalogs that consisted of 14,000 events. The threshold magnitude was fixed at M _w 4.8, but seismic zones like northern Pakistan–Tajikistan, Hindukush and northern Afghanistan–Tajikistan border had M _w 5.2. The average normalized ‘a’ and ‘b’ values for all zones are 6.15 and 0.95, respectively. Seismicity of study area was modeled, and ground motion was computed for eight frequencies (0.025, 0.1, 0.2, 0.5, 1.0, 1.5, 2.0, 2.5 s) for different annual exceedance rates of 0.02, 0.01, 0.005, 0.002 and 0.001 (return periods 50, 100, 200, 500 and 1,000 years) for stiff rocks at the gridding of 0.1° × 0.1°. Seismic hazard maps based on computed PGA for 0.02, 0.01 and 0.002 annual exceedance are prepared. These maps indicate the earthquake hazard of Pakistan and surrounding areas in the form of acceleration contour lines, which are in agreement with geological and seismotectonic characteristics of the study area. The maximum seismic hazard values are found at Muzaffarabad, Gilgit and Quetta areas.     

Probabilistic seismic hazard analysis for Kakrapar atomic power station, Gujarat, India

Seismic ground motion caused by earthquakes mainly affects the constructions and structures around its area of influence. In this context, the probabilistic seismic hazard analysis (PSHA) is a scientific step towards the safety analysis of any major construction such as nuclear power plant. Thus, the present study focused to estimate seismic hazard level at different probabilities for Kakrapar nuclear power plant located in the Western India. The hazard curves for the study area are developed following the procedure of PSHA suggested by Cornell–McGuire. Three source zones, Narmada-Tapti zone (NTZ), Rann of Kuchchh (ROK), and west passive margin (WPM), are classified on the basis of seismicity and tectonic setting of the study area. The estimated maximum magnitude (m _max) for NTZ, ROK, and WPM are 6.9 ± 0.57, 6.5 ± 0.64, and 6.1 ± 0.64, respectively. Logic tree approach has been used for the development of hazard curves to account the epistemic uncertainties associated with the analysis. For maximum credible earthquake [MCE, i.e., the probability of exceedance of 2 % in 50 years (return period of ~2,500 years)], the peak spectral acceleration (i.e., PSA at 0.2 s) expected around 5 km of the Kakrapar nuclear power plant (site) is 0.23 g from all source zones; however, at exact site location, it is 0.18 g. The PSA values due to NTZ, ROK, and WPM based on MCE are 0.22, 0.065, and 0.052 g, respectively. In case of design-based earthquake (DBE, i.e., 50 % probability in 50 years (return period of ~110 years)), the calculated maximum spectral acceleration (SA) from all source zones is about 0.045 g. The PSA distribution for the DBE from the NTZ has reached a maximum value of 0.042 g; however, PSA for ROK and WPM is considerably low with a maximum value of 0.022 and 0.021 g, respectively. Considering the MCE and DBE, the estimated PSA at 0.2 s has a highest value of ~0.23 g from all source zones. Spectral accelerations (SAs) correspond to different periods are presented, and SA plots for NTZ zone can be considered as response spectra for the KAPS site. Deaggregation of PSHA in the present study is also discussed. PGA values reported in seismic zonation map and global seismic hazard analysis program around the present study area range from 0.05 to 0.2 g which is slightly lower than the peak acceleration obtained in this study. The results of this study would facilitate in the performance of the site-specific seismic probabilistic safety analysis.     

Probabilistic seismic hazard assessment in the Constantine region,Northeast of Algeria

This paper presents a seismic hazard evaluation and develops an earthquake catalogue for the Constantine region over the period from 1357 to 2014. The study contributes to the improvement of seismic risk management by evaluating the seismic hazards in Northeast Algeria. A regional seismicity analysis was conducted based on reliable earthquake data obtained from various agencies (CRAAG, IGN, USGS and ISC). All magnitudes (M _l, m _b) and intensities (I ₀, I _MM, I _MSK and I _EMS) were converted to M _s magnitudes using the appropriate relationships. Earthquake hazard maps were created for the Constantine region. These maps were estimated in terms of spectral acceleration (SA) at periods of 0.1, 0.2, 0.5, 0.7, 0.9, 1.0, 1.5 and 2.0 s. Five seismogenic zones are proposed. This new method differs from the conventional method because it incorporates earthquake magnitude uncertainty and mixed datasets containing large historical events and recent data. The method can be used to estimate the b value of the Gutenberg-Richter relationship, annual activity rate λ(M) of an event and maximum possible magnitude M _max using incomplete and heterogeneous data files. In addition, an earthquake is considered a Poisson with an annual activity rate λ and with a doubly truncated exponential earthquake magnitude distribution. Map of seismic hazard and an earthquake catalogue, graphs and maps were created using geographic information systems (GIS), the Z-map code version 6 and Crisis software 2012.     

Probabilistic seismic and tsunami hazard analysis for design criteria development of a coastal area in the city of Banda Aceh

Both seismic and tsunami hazards design criteria are essential input to the rehabilitation and long-term development of city of Banda Aceh Post Sumatra 2004 (M _w=9.3) disaster. A case study to develop design criteria for future disaster mitigation of the area is presented. The pilot study consists of probabilistic seismic and tsunami hazard analysis. Results of the probabilistic seismic hazard analysis indicates that peak ground acceleration at baserock for 10 and 2% probability of exceedance in 50 years is 0.3 and 0.55 g, respectively. The analysis also provides spectral values at short (T=0.2 s) and long period (T=1.0 s) motions. Some non-linear time-domain earthquake response analyses for soft, medium, and hard site-class were conducted to recommend design response spectra for each site-class. In addition, tsunami inundation maps generated from probabilistic tsunami hazard analysis were developed through tsunami wave propagation analysis and run-up numerical modeling associated with its probability of tsunamigenic earthquake source potential. Both the seismic and tsunami hazard curve and design criteria are recommended as contribution of this study for design criteria, as part of the disaster mitigation effort in the development process of the city. The methodology developed herein could be applied to other seismic and tsunami disaster potential areas.     

Probabilistic seismic hazard assessment for Lake Van basin,Turkey

The seismic hazard for the Lake Van basin is computed using a probabilistic approach, along with the earthquake data from 1907 to present. The spatial distribution of seismic events between the longitudes of 41–45° and the latitudes of 37.5–40°, which encompasses the region, indicates distinct seismic zones. The positions of these zones are well aligned with the known tectonic features such as the Tutak-Çald?ran fault zone, the Özalp fault zone, the Geva? fault zone, the Bitlis fault zone and Karl?ova junction where the North Anatolian fault zone and East Anatolian fault zone meet. These faults are known to have generated major earthquakes which strongly affected cities and towns such as Van, Mu?, Bitlis, Özalp, Muradiye, Çald?ran, Erci?, Adilcevaz, Ahlat, Tatvan, Geva? and Gürp?nar. The recurrence intervals of M _s ≥ 4 earthquakes were evaluated in order to obtain the parameters of the Gutenberg–Richter measurements for seismic zones. More importantly, iso-acceleration maps of the basin were produced with a grid interval of 0.05 degrees. These maps are developed for 100- and 475- year return periods, utilizing the domestic attenuation relationships. A computer program called Sistehan II was utilized to generate these maps.