Kinetics of chromate reduction by pyrite and biotite under acidic conditions

The removal of chromate from aqueous solutions, using finely ground pyrite and biotite, was investigated by batch experiments. The kinetics and mechanism of chromate reduction are discussed here. Chromate reduction by pyrite was about 100 times faster than that by biotite, and was also faster at pH 3 than 4. When pyrite was used, more than 90% of the initial chromate was reduced within 4 h at pH 4, and within 40 min. at pH 3. However, with biotite more than 400 h was required for the reduction of 90% of the initial chromate. The results indicate that the rate of chromate reduction was strongly depending on the amount and dissolution rate of the Fe(II) in the minerals. The reduction of chromate at pH 4 resulted in the precipitation of (Cr, Fe)(OH)_3(s), which is believed to have limited the concentrations of dissolved Cr(III) and Fe(III) to less than the expected values. When biotite was used, the amounts of decreased Fe(II) and reduced Cr(VI) showed no stoichiometric relationship, which implies that not only was there chromate reduction by Fe(II) ions in the acidic solution, but also heterogeneous reduction of Fe(III) ions by structural Fe(II) in biotite. However, the results from a series of the experiments using pyrite showed that the concentrations of the decreased Fe(II) and the reduced Cr(VI) were close to the stoichiometric ratio of 3:1. This was because the oxidation of pyrite rapidly created Fe(II) ions, even in oxygenated solutions, and the chromate reduction by the Fe(II) ions was significantly faster than the Fe(II) ion oxygenation. When compared with the experimental sets controlled at an initial pH of 3, the pH of the biotite batch, which was not controlled, increased to 3.4. Because of the increase in the pH, Cr(VI) was not completely removed, and 25% (1.2–1.3 mg/L Cr(VI)) of the initial concentration remained for up to 1000 h. The pH increase is, in most cases, caused by the hydrolysis of clay minerals. However, in the pyrite batches, there was no difference in the variations of the chromate reduction in relation to the pH control. There was also no difference in the capacity and rate of Cr(VI) reduction in 0.01 M NaCl or Na₂SO₄ solutions. In the 0.01 M NaH₂PO₄ solution pyrite experiment, the Cr(VI) was not completely removed, despite the maintenance of the pH at 3. The dominant Fe species was about 10 mg/L Fe(III) and few Fe(II) ions existed in solution. The Fe phosphate (Fe₃(PO₄)₂ or FePO₄) coatings on the surface of pyrite prevented access of O₂ or Cr(VI). Therefore, the surface coatings are likely to have caused the deterioration of the Cr(VI) reduction capacity in the NaH₂PO₄ solution.     

Arsenic redox transformation by humic substances and Fe minerals

The toxicity and mobility of the redox-active metalloid As strongly depends on its oxidation state, with As(III) (arsenite) being more toxic and mobile than As(V) (arsenate). It is, therefore, necessary to know the biogeochemical processes potentially influencing As redox state to understand and predict its environmental behavior. The first part of this presentation will discuss the quantification of As redox changes by pH-neutral mineral suspensions of goethite [α-Fe^IIIOOH] amended with Fe(II) using wet-chemical and synchrotron X-ray absorption (XANES) analysis (Amstaetter et al., 2010). First, it was found that goethite itself did not oxidize As(III). Second, in contrast to thermodynamic predictions, Fe(II)–goethite systems did not reduce As(V). However, surprisingly, rapid oxidation of As(III) to As(V) was observed in Fe(II)–goethite systems. Iron speciation and mineral analysis by Mössbauer spectroscopy showed rapid formation of ⁵⁷Fe–goethite after ⁵⁷Fe(II) addition and the formation of a so far unidentified additional Fe(II) phase. No other Fe(III) phase could be detected by Mössbauer spectroscopy, EXAFS, scanning electron microscopy, X-ray diffraction or high-resolution transmission electron microscopy. This suggests that reactive Fe(III) species form as an intermediate Fe(III) phase upon Fe(II) addition and electron transfer into bulk goethite but before crystallization of the newly formed Fe(III) as goethite.The second part of the presentation will show that semiquinone radicals produced during microbial or chemical reduction of a humic substance model quinone (AQDS, 9,10-anthraquinone-2,6-disulfonic acid) can react with As and change its redox state (Jiang et al., 2009). The results of these experiments showed that these semiquinone radicals are strong oxidants and oxidize arsenite to arsenate, thus decreasing As toxicity and mobility. The oxidation of As(III) depended strongly on pH. More arsenite (up to 67.3%) was oxidized at pH 11 compared to pH 7 (12.6% oxidation) and pH 3 (0.5% oxidation). In addition to As(III) oxidation by semiquinone radicals, hydroquinones that were also produced during quinone reduction, reduced As(V) to As(III) at neutral and acidic pH values (less than 12%) but not at alkaline pH. In an attempt to understand the observed redox reactions between As and reduced/oxidized quinones present in humic substances, the radical content in reduced AQDS solutions was quantified and Eh-pH diagrams were constructed. Both the radical quantification and the Eh-pH diagram allowed explaining the observed redox reactions between the reduced AQDS solutions and the As.In summary these studies indicate that in the simultaneous presence of Fe(III) oxyhydroxides, Fe(II), and humic substances as commonly observed in environments inhabited by Fe-reducing microorganisms, As(III) oxidation can occur. This potentially explains the presence of As(V) in reduced groundwater aquifers.     

石英与钠长石浮选分离的研究

用十八胺(阳离子捕收剂)和十二烷基磺酸钠(阴离子捕收剂,SDS)作浮选为捕收剂分离石英与钠长石,研究了浮选条件对分离效果的影响以及捕收剂在矿物表面的吸附行为.结果表明,最佳浮选条件是浮选液的pH=2,阴、阳离子捕收剂的浓度分别为3.0×10-6 mol/L和4.0×10-6 mol/L;阴阳离子捕收剂在石英与钠长石两种矿物上表现出相同的吸附行为.在最佳浮选条件下,对不同配比的石英和钠长石混合物进行浮选,石英回收率为14%,钠长石回收率达80%,分离效果显著;对含微量长石的石英矿粉进行浮选,分离效果与石英与钠长石混合物相近.     

Evaluation of redox-active iron sites in smectites using middle and near infrared spectroscopy

Redox processes of structural Fe in clay minerals play an important role in biogeochemical cycles and for the dynamics of contaminant transformation in soils and aquifers. Reactions of Fe(II)/Fe(III) in clay minerals depend on a variety of mineralogical and environmental factors, which make the assessment of Fe redox reactivity challenging. Here, we use middle and near infrared (IR) spectroscopy to identify reactive structural Fe(II) arrangements in four smectites that differ in total Fe content, octahedral cationic composition, location of the negative excess charge, and configuration of octahedral hydroxyl groups. Additionally, we investigated the mineral properties responsible for the reversibility of structural alterations during Fe reduction and re-oxidation. For Wyoming montmorillonite (SWy-2), a smectite of low structural Fe content (2.8 wt%), we identified octahedral AlFe(II)-OH as the only reactive Fe(II) species, while high structural Fe content (>12 wt%) was prerequisite for the formation of multiple Fe(II)-entities (dioctahedral AlFe(II)-OH, MgFe(II)-OH, Fe(II)Fe(II)-OH, and trioctahedral Fe(II)Fe(II)Fe(II)-OH) in iron-rich smectites Ölberg montmorillonite, and ferruginous smectite (SWa-1), as well as in synthetic nontronite. Depending on the overall cationic composition and the location of excess charge, different reactive Fe(II) species formed during Fe reduction in iron-rich smectites, including tetrahedral Fe(II) groups in synthetic nontronite. Trioctahedral Fe(II) domains were found in tetrahedrally charged ferruginous smectite and synthetic nontronite in their reduced state while these Fe(II) entities were absent in Ölberg montmorillonite, which exhibits an octahedral layer charge. Fe(III) reduction in iron-rich smectites was accompanied by intense dehydroxylation and structural rearrangements, which were only partially reversible through re-oxidation. Re-oxidation of Wyoming montmorillonite, in contrast, restored the original mineral structure. Fe(II) oxidation experiments with nitroaromatic compounds as reactive probes were used to link our spectroscopic evidence to the apparent reactivity of structural Fe(II) in a generalized kinetic model, which takes into account the presence of Fe(II) entities of distinctly different reactivity as well as the dynamics of Fe(II) rearrangements.     

Biomineralization of lepidocrocite and goethite by nitrate-reducing Fe(II)-oxidizing bacteria: Effect of pH, bicarbonate, phosphate, and humic acids

Fe(III) solid phases are the products of Fe(II) oxidation by Fe(II)-oxidizing bacteria, but the Fe(III) phases reported to form within growth experiments are, at times, poorly crystalline and therefore difficult to identify, possibly due to the presence of ligands (e.g., phosphate, carbonate) that complex iron and disrupt iron (hydr)oxide precipitation. The scope of this study was to investigate the influences of geochemical solution conditions (pH, carbonate, phosphate, humic acids) on the Fe(II) oxidation rate and Fe(III) mineralogy. Fe(III) mineral characterization was performed using ⁵⁷Fe-Mössbauer spectroscopy and μ-X-ray diffraction after oxidation of dissolved Fe(II) within Mops-buffered cell suspensions of Acidovorax sp. BoFeN1, a nitrate-reducing, Fe(II)-oxidizing bacterium. Lepidocrocite (γ-FeOOH) (90%), which also forms after chemical oxidation of Fe(II) by dissolved O₂, and goethite (α-FeOOH) (10%) were produced at pH 7.0 in the absence of any strongly complexing ligands. Higher solution pH, increasing concentrations of carbonate species, and increasing concentrations of humic acids promoted goethite formation and caused little or no changes in Fe(II) oxidation rates. Phosphate species resulted in Fe(III) solids unidentifiable to our methods and significantly slowed Fe(II) oxidation rates. Our results suggest that Fe(III) mineralogy formed by bacterial Fe(II) oxidation is strongly influenced by solution chemistry, and the geochemical conditions studied here suggest lepidocrocite and goethite may coexist in aquatic environments where nitrate-reducing, Fe(II)-oxidizing bacteria are active.     

Reductive biotransformation of Fe in shale-limestone saprolite containing Fe(III) oxides and Fe(II)/Fe(III) phyllosilicates

A <2.0-mm fraction of a mineralogically complex subsurface sediment containing goethite and Fe(II)/Fe(III) phyllosilicates was incubated with Shewanella putrefaciens (strain CN32) and lactate at circumneutral pH under anoxic conditions to investigate electron acceptor preference and the nature of the resulting biogenic Fe(II) fraction. Anthraquinone-2,6-disulfonate (AQDS), an electron shuttle, was included in select treatments to enhance bioreduction and subsequent biomineralization. The sediment was highly aggregated and contained two distinct clast populations: (i) a highly weathered one with “sponge-like” internal porosity, large mineral crystallites, and Fe-containing micas, and (ii) a dense, compact one with fine-textured Fe-containing illite and nano-sized goethite, as revealed by various forms of electron microscopic analyses. Approximately 10-15% of the Fe(III)_TOT was bioreduced by CN32 over 60 d in media without AQDS, whereas 24% and 35% of the Fe(III)_TOT was bioreduced by CN32 after 40 and 95 d in media with AQDS. Little or no Fe²⁺, Mn, Si, Al, and Mg were evident in aqueous filtrates after reductive incubation. Mössbauer measurements on the bioreduced sediments indicated that both goethite and phyllosilicate Fe(III) were partly reduced without bacterial preference. Goethite was more extensively reduced in the presence of AQDS whereas phyllosilicate Fe(III) reduction was not influenced by AQDS. Biogenic Fe(II) resulting from phyllosilicate Fe(III) reduction remained in a layer-silicate environment that displayed enhanced solubility in weak acid. The mineralogic nature of the goethite biotransformation product was not determined. Chemical and cryogenic Mössbauer measurements, however, indicated that the transformation product was not siderite, green rust, magnetite, Fe(OH)₂, or Fe(II) adsorbed on phyllosilicate or bacterial surfaces. Several lines of evidence suggested that biogenic Fe(II) existed as surface associated phase on the residual goethite, and/or as a Fe(II)-Al coprecipitate. Sediment aggregation and mineral physical and/or chemical factors were demonstrated to play a major role on the nature and location of the biotransformation reaction and its products.     

Modeling transport of arsenic through modified granular natural siderite filters for arsenic removal

Groundwater arsenic(As)contamination is a hot issue,which is severe health concern worldwide.Recently,many Fe-based adsorbents have been used for As removal from solutions.Modified granular natural siderite(MGNS),a special hybrid Fe(II)/Fe(III)system,had higher adsorption capacity for As(III)than As(V),but the feasibility of its application in treating high-As groundwater is still unclear.In combination with transport modeling,laboratory column studies and field pilot tests were performed to reveal both mechanisms and factors controlling As removal by MGNS-filled filters.Results show that weakly acid pH and discontinuous treatment enhanced As(Ⅲ)removal,with a throughput of 8700 bed volumes(BV)of 1.0 mg/L As(Ⅲ)water at breakthrough of 10 μg/L As at pH 6.Influent HCO_3~-inhibited As removal by the filters.Iron mineral species,SEM and XRD patterns of As-loading MGNS show that the important process contributing to high As(Ⅲ)removal was the mineral transformation from siderite to goethite in the filter.The homogeneous surface diffusion modeling(HSDM)shows that competition between As(III)and HCO_3~-with adsorption sites on MGNS was negligible.The inhibition of HCO_3~-on As(Ⅲ)removal was connected to inhibition of siderite dissolution and mineral transformation.Arsenic loadings were lower in field pilot tests than those in the laboratory experiments,showing that high concentrations of coexisting anions(especially HCO_3~-and SiO_4~(4-)),high pH,low EBCT,and low groundwater temperature decreased As removal.It was suggested that acidification and aeration of highAs groundwater and discontinuous treatment would improve the MGNS filter performance of As removal from real high-As groundwater.     

Adsorption of heavy metals in glacial till soil

The charged sites on soil particles are important for the retention/adsorption of metals. Metallic counterions can neutralize the intrinsic charges on the surfaces of soil particles by forming complexes. In this study, efforts have been made to determine the effect of surface potential, pH, and ionic strength on the adsorption of four metal ions, hexavalent chromium Cr(VI), trivalent chromium Cr(III), nickel Ni(II) and cadmium Cd(II), in glacial till soil. Batch tests were performed to determine the effect of pH (2–12) and ionic strength (0.001–0.1 M KCl) on zeta potential of the glacial till soil. The point of zero charge (pH _PZC ) of glacial till was found to be 7.0±2.5. Surface charge experiments revealed the high buffering capacity of the glacial till. Batch adsorption experiments were conducted at natural pH (8.2) using various concentrations of selected metals. The adsorption data was described by the Freundlich adsorption model. Overall glacial till shows lower adsorption affinity to Cr(VI) as compared to cationic metals, Cr(III), Ni(II) and Cd(II).     

Assessment of the geochemical reactivity of Fe-DOM complexes in wetland sediment pore waters using a nitroaromatic probe compound

The reductive capacity of Fe(II) present in anoxic sediment pore waters affects biogeochemically significant processes that occur in these environments, such as metal speciation, mineral solubility, nutrient bioavailability, and the transformation of anthropogenic organic compounds. We studied the reduction of pentachloronitrobenzene (PCNB) in natural pore waters to elucidate the reductive capacity of Fe(II) complexes, and monitored the redox-active species responsible for the observed kinetics. Differential pulse polarography (DPP) scans of sediment pore waters from a coastal Lake Erie wetland (Old Woman Creek National Estuarine Research Reserve, Huron, OH) revealed an increase in both Fe(III)-organic and Fe(II) species to a depth of ∼30 cm below the sediment-water interface. Concentrations of dissolved organic matter (DOM) in pore waters increased while pH decreased with depth. We found that Fe(II) was necessary for rapid PCNB reduction (<24 h), and observed faster reduction with increased pH. PCNB reduction in preserved pore waters (acidified to pH 2.5 after pore water extraction and raised to the native pH (6.7-7.6) prior to reaction) was similar to that observed in a model system containing Fe(II) and fulvic acid isolated from this site. Conversely, PCNB reduction in unaltered pore water was significantly slower than that observed in preserved pore water, indicating that the Fe(II) speciation and its reductive capacity differed. DPP scans of pore waters used for kinetic studies confirmed that pH-adjustment affected Fe_T speciation in the pore waters, as the Fe(III)-DOM peak current was lowered or disappeared completely in the preserved pore water samples. These data show that pH-adjustment of pore waters presumably alters both their complexation chemistry and reactivity towards PCNB, and shows how small changes in Fe complexation can potentially affect redox chemistry in anoxic environments. Our results also show that reactive organic Fe(II) complexes are naturally present in wetland sediment pore waters, and that these species are potentially important mediators of Fe(II)/Fe(III) redox biogeochemistry in anoxic sedimentary environments.     

Abundance, Sources and Speciation of Trace Elements in Humus-Rich Streams Affected by Acid Sulphate Soils

The behaviour of trace elements (Al, As, Cd, Co, Cr,Cu, Fe, Mn, Ni, V, Zn) was studied in five humus-richstreams (dissolved organic carbon = 14–40 mg/L)impacted by acid sulphate soils developed in marinesulphide-bearing fine-grained sediments. During heavyrainfalls in autumn, on which the study focusses, themetals Al, Cd, Co, Cu, Mn, Ni and Zn are extensivelyleached from these acidic soils (pH = 2.5–4.5), whileAs, Cr, Fe and V are not leached more strongly fromthis soil type than from areas of till and peat. Aspeciation experiment, based on anion and cationexchange of the stream waters in the field, showedthat (1) the metals Al, Cd, Co, Mn, Ni and Zn aretransported in the streams mainly as inorganiccations, (2) Cu exists mainly in cationic form but isalso to a significant extent associated with dissolvedhumic substances, (3) Fe occurs mainly in the anionicfraction explained by organic coating on colloidal Feoxyhydoxides and (4) the hydrochemistry of As, Cr andV is complex as these elements may exist in severalunquantified anionic fractions and to a minor extentin cationic species/forms. Whereas the proportion ofacid sulphate soils in the catchments had a largeimpact on concentrations levels of several elements inthe stream waters, these soils did not have a largeaffect on the speciation of elements in water.     

Chromium speciation and mobility in a high level nuclear waste vadose zone plume

Radioactive core samples containing elevated concentrations of Cr from a high level nuclear waste plume in the Hanford vadose zone were studied to asses the future mobility of Cr. Cr(VI) is an important subsurface contaminant at the Hanford Site. The plume originated in 1969 by leakage of self-boiling supernate from a tank containing REDOX process waste. The supernate contained high concentrations of alkali (NaOH ≈ 5.25 mol/L), salt (NaNO₃/NaNO₂ >10 mol/L), aluminate [Al(OH)₄⁻ = 3.36 mol/L], Cr(VI) (0.413 mol/L), and ¹³⁷Cs⁺ (6.51 × 10⁻⁵ mol/L). Water and acid extraction of the oxidized subsurface sediments indicated that a significant portion of the total Cr was associated with the solid phase. Mineralogic analyses, Cr valence speciation measurements by X-ray adsorption near edge structure (XANES) spectroscopy, and small column leaching studies were performed to identify the chemical retardation mechanism and leachability of Cr. While X-ray diffraction detected little mineralogic change to the sediments from waste reaction, scanning electron microscopy (SEM) showed that mineral particles within 5 m of the point of tank failure were coated with secondary, sodium aluminosilicate precipitates. The density of these precipitates decreased with distance from the source (e.g., beyond 10 m). The XANES and column studies demonstrated the reduction of 29-75% of the total Cr to insoluble Cr(III), and the apparent precipitation of up to 43% of the Cr(VI) as an unidentified, non-leachable phase. Both Cr(VI) reduction and Cr(VI) precipitation were greater in sediments closer to the leak source where significant mineral alteration was noted by SEM. These and other observations imply that basic mineral hydrolysis driven by large concentrations of OH⁻ in the waste stream liberated Fe(II) from the otherwise oxidizing sediments that served as a reductant for CrO₄²⁻. The coarse-textured Hanford sediments contain silt-sized mineral phases (biotite, clinochlore, magnetite, and ilmenite) that are sources of Fe(II). Other dissolution products (e.g., Ba²⁺) or Al(OH)₄⁻ present in the waste stream may have induced Cr(VI) precipitation as pH moderated through mineral reaction. The results demonstrate that a minimum of 42% of the total Cr inventory in all of the samples was immobilized as Cr(III) and Cr(VI) precipitates that are unlikely to dissolve and migrate to groundwater under the low recharge conditions of the Hanford vadose zone.     

Accurate determination of Fe(II) concentrations in the presence of a very high soluble Fe(III) background

Analytical methods used for determining dissolved Fe(II) often yield inaccurate results in the presence of high Fe(III) concentrations. Accurate analysis of Fe(II) in solution when it is less than 1% of the total dissolved Fe concentration (Fe_T) is sometimes required in both geochemical and environmental studies. For example, such analysis is imperative for obtaining the ratio Fe(II)/Fe(III) in rocks, soils and sediments, for determining the kinetic constants of Fe(II) oxidation in chemical or biochemical systems operating at low pH, and is also important in environmental engineering projects, e.g. for proper control of the regeneration step (oxidation of Fe(II) into Fe(III)) applied in ferric-based gas desulphurization processes. In this work a method capable of yielding accurate Fe(II) concentrations at Fe(II) to Fe_T ratios as low as 0.05% is presented. The method is based on a pretreatment procedure designed to separate Fe(II) species from Fe(III) species in solution without changing the original Fe(II) concentration. Once separated, a modified phenanthroline method is used to determine the Fe(II) concentration, in the virtual absence of Fe(III) species. The pretreatment procedure consists of pH elevation to pH 4.2–4.65 using NaHCO₃ under N₂(g) environment, followed by filtration of the solid ferric oxides formed, and subsequent acidification of the Fe(II)-containing filtrate. Accuracy of Fe(II) analyses obtained for samples (Fe(II)/Fe_T ratios between 2% and 0.05%) to which the described pretreatment was applied was >95%. Elevating pH to above 4.65 during pretreatment was shown to result in a higher error in Fe(II) determination, likely resulting from adsorption of Fe(II) species and their removal from solution with the ferric oxide precipitate.     

Effects of humic substances on Fe(II) sorption onto aluminum oxide and clay

We studied the effects of humic substances (HS) on the sorption of Fe(II) onto Al-oxide and clay sorbents at pH 7.5 with a combination of batch kinetic experiments and synchrotron Fe K-edge EXAFS analyses. Fe(II) sorption was monitored over the course of 4 months in anoxic clay and Al-oxide suspensions amended with variable HS types (humic acid, HA; or fulvic acid, FA) and levels (0, 1, and 4 wt%), and with differing Fe(II) and HS addition sequences (co-sorption and pre-coated experiments, where Fe(II) sorbate was added alongside and after HS addition, respectively). In the Al-oxide suspensions, the presence of HS slowed down the kinetics of Fe(II) sorption, but had limited, if any, effect on the equilibrium aqueous Fe(II) concentrations. EXAFS analyses revealed precipitation of Fe(II)–Al(III)-layered double hydroxide (LDH) phases as the main mode of Fe(II) sorption in both the HA-containing and HA-free systems. These results demonstrate that HS slow down Fe(II) precipitation in the Al-oxide suspensions, but do not affect the composition or stability of the secondary Fe(II)–Al(III)-LDH phases formed. Interference of HS with the precipitation of Fe(II)–Al(III)-LDH was attributed to the formation organo-Al complexes HS limiting the availability of Al for incorporation into secondary layered Fe(II)-hydroxides. In the clay systems, the presence of HA caused a change in the main Fe(II) sorption product from Fe(II)–Al(III)-LDH to a Fe(II)-phyllosilicate containing little structural Al. This was attributed to complexation of Al by HA, in combination with the presence of dissolved Si in the clay suspension enabling phyllosilicate precipitation. The change in Fe(II) precipitation mechanism did not affect the rate of Fe(II) sorption at the lower HA level, suggesting that the inhibition of Fe(II)–Al(III)-LDH formation in this system was countered by enhanced Fe(II)-phyllosilicate precipitation. Reduced rates of Fe(II) sorption at the higher HA level were attributed to surface masking or poisoning by HA of secondary Fe(II) mineral growth at or near the clay surface. Our results suggest that HS play an important role in controlling the kinetics and products of Fe(II) precipitation in reducing soils, with effects modulated by soil mineralogy, HS content, and HS properties. Further work is needed to assess the importance of layered Fe(II) hydroxides in natural reducing environments.     

Structural and compositional evolution of Cr/Fe solids after indirect chromate reduction by dissimilatory iron-reducing bacteria

The mobility and toxicity of Cr within surface and subsurface environments is diminished by the reduction of Cr(VI) to Cr(III). The reduction of hexavalent chromium can proceed via chemical or biological means. Coupled processes may also occur including reduction via the production of microbial metabolites, including aqueous Fe(II). The ultimate pathway of Cr(VI) reduction will dictate the reaction products and hence the solubility of Cr(III). Here, we investigate the fate of Cr following a coupled biotic-abiotic reduction pathway of chromate under iron-reducing conditions. Dissimilatory bacterial reduction of two-line ferrihydrite indirectly stimulates reduction of Cr(VI) by producing aqueous Fe(II). The product of this reaction is a mixed Fe(III)-Cr(III) hydroxide of the general formula Fe_1−xCr_x(OH)₃ · nH₂O, having an α/β-FeOOH local order. As the reaction proceeds, Fe within the system is cycled (i.e., Fe(III) within the hydroxide reaction product is further reduced by dissimilatory iron-reducing bacteria to Fe(II) and available for continued Cr reduction) and the hydroxide products become enriched in Cr relative to Fe, ultimately approaching a pure Cr(OH)₃ · nH₂O phase. This Cr purification process appreciably increases the solubility of the hydroxide phases, although even the pure-phase chromium hydroxide is relatively insoluble.     

Analysis of long-term bacterial vs. chemical Fe(III) oxide reduction kinetics

Data from studies of dissimilatory bacterial (10⁸ cells mL⁻¹ of Shewanella putrefaciens strain CN32, pH 6.8) and ascorbate (10 mM, pH 3.0) reduction of two synthetic Fe(III) oxide coated sands and three natural Fe(III) oxide-bearing subsurface materials (all at ca. 10 mmol Fe(III) L⁻¹) were analyzed in relation to a generalized rate law for mineral dissolution (J_t/m₀ = k′(m/m₀)^γ, where J_t is the rate of dissolution and/or reduction at time t, m₀ is the initial mass of oxide, and m/m₀ is the unreduced or undissolved mineral fraction) in order to evaluate changes in the apparent reactivity of Fe(III) oxides during long-term biological vs. chemical reduction. The natural Fe(III) oxide assemblages demonstrated larger changes in reactivity (higher γ values in the generalized rate law) compared to the synthetic oxides during long-term abiotic reductive dissolution. No such relationship was evident in the bacterial reduction experiments, in which temporal changes in the apparent reactivity of the natural and synthetic oxides were far greater (5-10 fold higher γ values) than in the abiotic reduction experiments. Kinetic and thermodynamic considerations indicated that neither the abundance of electron donor (lactate) nor the accumulation of aqueous end-products of oxide reduction (Fe(II), acetate, dissolved inorganic carbon) are likely to have posed significant limitations on the long-term kinetics of oxide reduction. Rather, accumulation of biogenic Fe(II) on residual oxide surfaces appeared to play a dominant role in governing the long-term kinetics of bacterial crystalline Fe(III) oxide reduction. The experimental findings together with numerical simulations support a conceptual model of bacterial Fe(III) oxide reduction kinetics that differs fundamentally from established models of abiotic Fe(III) oxide reductive dissolution, and indicate that information on Fe(III) oxide reactivity gained through abiotic reductive dissolution techniques cannot be used to predict long-term patterns of reactivity toward enzymatic reduction at circumneutral pH.     

Adsorption of hydroxamate siderophores and EDTA on goethite in the presence of the surfactant sodium dodecyl sulfate

Siderophore-promoted iron acquisition by microorganisms usually occurs in the presence of other organic molecules, including biosurfactants. We have investigated the influence of the anionic surfactant sodium dodecyl sulfate (SDS) on the adsorption of the siderophores DFOB (cationic) and DFOD (neutral) and the ligand EDTA (anionic) onto goethite (α-FeOOH) at pH 6. We also studied the adsorption of the corresponding 1:1 Fe(III)-ligand complexes, which are products of the dissolution process. Adsorption of the two free siderophores increased in a similar fashion with increasing SDS concentration, despite their difference in molecule charge. In contrast, SDS had little effect on the adsorption of EDTA. Adsorption of the Fe-DFOB and Fe-DFOD complexes also increased with increasing SDS concentrations, while adsorption of Fe-EDTA decreased. Our results suggest that hydrophobic interactions between adsorbed surfactants and siderophores are more important than electrostatic interactions. However, for strongly hydrophilic molecules, such as EDTA and its iron complex, the influence of SDS on their adsorption seems to depend on their tendency to form inner-sphere or outer-sphere surface complexes. Our results demonstrate that surfactants have a strong influence on the adsorption of siderophores to Fe oxides, which has important implications for siderophore-promoted dissolution of iron oxides and biological iron acquisition.     

Reactive iron(III) in sediments: Chemical versus microbial extractions

The availability of particulate Fe(III) to iron reducing microbial communities in sediments and soils is generally inferred indirectly by performing chemical extractions. In this study, the bioavailability of mineral-bound Fe(III) in intertidal sediments of a eutrophic estuary is assessed directly by measuring the kinetics and extent of Fe(III) utilization by the iron reducing microorganism Shewanella putrefaciens, in the presence of excess electron donor. Microbial Fe(III) reduction is compared to chemical dissolution of iron from the same sediments in buffered ascorbate-citrate solution (pH 7.5), ascorbic acid (pH 2), and 1 M HCl. The results confirm that ascorbate at near-neutral pH selectively reduces the reactive Fe(III) pool, while the acid extractants mobilize additional Fe(II) and less reactive Fe(III) mineral phases. Furthermore, the maximum concentrations of Fe(III) reducible by S. putrefaciens correlate linearly with the iron concentrations extracted by buffered ascorbate-citrate solution, but not with those of the acid extractions. However, on average, only 65% of the Fe(III) reduced in buffered ascorbate-citrate solution can be utilized by S. putrefaciens, probably due to physical inaccessibility of the remaining fraction of reactive Fe(III) to the cells. While the microbial and abiotic reaction kinetics further indicate that reduction by ascorbate at near-neutral pH most closely resembles microbial reduction of the sediment Fe(III) pool by S. putrefaciens, the results also highlight fundamental differences between chemical reductive dissolution and microbial utilization of mineral-bound ferric iron.     

ANC,BNC and mobilization of Cr from polluted sediments in function of pH changes

During the manufacturing of chromate salts (1972–1992) large quantities of Chromite Ore Processing Residue (COPR) were released into a decantation pond east of the former chemical plant of Porto-Romano (Durres, Albania), giving rise to yellow colored pond sediments. These Cr(VI) bearing sediments were deposited upon Quaternary silty-clay lagoonal sediments rich in iron oxides and organic matter. The pH values in these lagoonal sediments vary around 6.6, while in the pond sediments, it is mainly acidic (due to the presence of the sulfur stock piles in the area and the release of the H₂SO₄ from the activity of the former chemical plant), varying between 1.4 and 3.8. Continuous leaching of the COPR waste resulted in yellow-colored surface water runoff. The prediction of pH changes in the different types of sediments based upon acid/base neutralizing capacity (ANC/BNC) jointly with the quantitative data on release of heavy metals and especially Cr is considered an important advantage of the pH_stat leaching test if compared to conventional leaching procedures. Thus, factors controlling the leaching of Cr(VI), Cr(III), Ca, Al, Fe, Mg from the COPR were investigated by means of pH_stat batch leaching tests and mineralogical analysis. Moreover, mathematical and geochemical modeling complemented the study. The COPR in the area contain very high concentrations of chromium 24,409 mg/kg, which mainly occurs as Cr(III) (75–90%) as well as Cr(VI) (25–10%). The leaching of Cr(VI) occurs in all the range (2–10) of the tested pH values, however, it decreases under acidic conditions. Beside some reduction of Cr(VI) to Cr(III), the Cr(VI) content of the leachtes remains relatively high in the acidic environment, while the limning of Cr(VI) pond sediments will increase the release of the latter specie. The leaching of the Cr(III) occurs strictly under acidic conditions, whereby limning of these sediments will give rise to the lower solubility of Cr(III). The key mineral phases responsible for the fast release of the Cr(VI) are: the chromate salts (i.e. sodium chromate and sodium dichromate), while sparingly soluble chromatite (CaCrO₄) and hashemite (BaCrO₄) release Cr(VI) very slowly. Thus, pH and mineral solubility have been identified as key factors in the retention and the release of the hexavalent CrO₄ ²⁻ and Cr₂O₇ ⁻ from the COPR-rich pond sediments.     

Siderophore-promoted dissolution of cobalt from hydroxide minerals

Recent research has revealed that siderophores, a class of biogenic ligands with high affinities for Fe(III), can also strongly complex Co(III), an element essential to the normal metabolic function of microbes and animals. This study was conducted to quantify the rates and identify the products and mechanisms of the siderophore-promoted dissolution of Co from synthetic Co-bearing minerals. The dissolution reactions of heterogenite (CoOOH) and four Co-substituted goethites (Co-FeOOH) containing different Co concentrations were investigated in the presence of a trihydroxamate siderophore, desferrioxamine B (DFOB), using batch and flow-through experiments. Results showed that DFOB-promoted dissolution of Co from Co-bearing minerals may occur via pH-dependent ligand-promoted or reductive dissolution mechanisms. For heterogenite, ligand-promoted dissolution was the dominant pathway at neutral to alkaline pH, while production of dissolved Co(II) for pH <6. It was not possible from our data to decouple the separate contributions of homogenous and heterogeneous reduction reactions to the aqueous Co(II) pool. Cobalt substitution in Co-substituted goethite, possibly caused by distortion of goethite structure and increased lattice strain, resulted in enhanced total dissolution rates of both Co and Fe. The DFOB-promoted dissolution rates of Co-bearing minerals, coupled with the high affinity of Co(III) for DFOB, suggest that siderophores may be effective for increasing Co solubility, and thus possibly Co bioavailability. The results also suggest that siderophores may contribute to the mobilization of radioactive ⁶⁰Co from Co-bearing mineral phases through mineral weathering and dissolution processes.