Modeling of RC columns strengthened with RC jackets

Constructing concrete jackets is a common technique when strengthening reinforced concrete (RC) columns, particularly in seismic regions. However, there are many uncertainties concerning the behavior of the composite specimen, particularly at the interface between the old and new concrete. In this paper, monotonic finite element (FE) analyses are performed to examine the behavior of strengthened columns under monotonic and cyclic loading. Through investigating two independent series of experimental results, it is demonstrated that monotonic FE analysis with appropriate assumptions can simulate both monotonic and cyclic loading conditions to a reasonable degree of accuracy. According to the results of this study, it is found that a simulation of the interface between the old and the new concrete is vital and cannot be ignored by simply considering a perfect bond at the interface. In the case of strengthened RC columns subjected to cyclic loading, strength degradation at the interface has to be included and can be effectively modeled by reducing the coefficients of friction and adhesion by using a proposed formula. Finally, the effect of jacket concrete shrinkage is simulated that leads to a reduced maximum load and stiffness of strengthened columns. Copyright © 2011 John Wiley & Sons, Ltd.     

钢管混凝土叠合柱边框内藏钢桁架核心筒抗震性能试验研究

为进一步改善混凝土核心简的抗震性能,本文提出了钢管混凝土叠合柱边框内藏钢桁架组合核心筒.进行了2个1/6缩尺的核心筒模型在低周反复荷载下的抗震性能试验研究,1个为钢管混凝土叠合柱边框毛组合核心筒,1个为钢管混凝土叠合柱边框内藏钢桁架组合核心筒.通过试验,对比分析了2个核心简的承载力、延性、刚度及其衰减、滞回特性、耗能能力及破坏特征,给出了钢管混凝土叠合柱边框内藏钢桁架组合核心筒的承载力计算模型,计算结果与实测值符合较好.研究表明,钢管混凝土叠合柱边框内藏钢桁架组合核心筒与钢管混凝土叠合柱边框组合核心筒相比,其抗震性能明显提高.     

震损加固后RC柱抗震性能影响因素分析

整理了国内外相关规范与相关研究中对RC柱抗震性态划分方法与指标限值,发现均是针对未震损未加固的RC柱.以相关试验得到的未预损未加固、未预损直接加固、预损后再加固的RC柱骨架曲线为对象,直接套用现有针对未震损未加固RC柱的性态划分方法与指标限值进行划分,得到对应各抗震性态分隔点处的位移角限值,发现3类RC柱在相同位移角下...     

Probabilistic assessment for seismic performance of port structures

Past experience has shown that ports are often susceptible to severe damage during earthquakes. From field damage data of 1995 Kobe earthquake, it is observed that the seismic behavior of port structures shows significant variability. In this study, a 2D numerical model, representing PC1 berth located in Port Island, Kobe and damaged in the 1995 Kobe earthquake, has been developed and used to simulate seismic behavior. It has been found that the uncertainties in the friction angle and the shear modulus of reclaimed soil contribute most to the variability of the residual horizontal displacement (RHD) response of the quay wall of port structures. To investigate the propagation of uncertainties of soil–structure system to the quay wall, a tornado diagram and a first-order second-moment analysis are used. Uncertainty of ground motions has also been investigated. Based on the results, design considerations have been provided.     

规则钢筋混凝土异形柱框架结构的抗震性能研究

本文按现行规范及技术规程设计了设防烈度为8度的一个规则的钢筋混凝土异形柱框架,并进行了单向水平地震作用下的空间三维非线性地震反应分析,考查了异形柱框架结构在设防和罕遇地震水准下的整体抗震性能,对结构能否达到抗震设防目标进行了初步评价。结果表明,8度区按规范设计的结构在设防烈度及罕遇烈度地震作用下基本能够达到预期的抗震设防目标。     

Seismic retroftting of RC columns with RC jackets and wing walls with different structural details

An original reinforced concrete(RC) column and four strengthened specimens, two with RC jackets and two with wing walls, were tested in this study. The original column specimen was designed to comply with older(pre-1999) design standards so that the usual detailing defi ciencies in existing school buildings in Taiwan could be simulated. Two different structural details were chosen to fabricate the full-scale specimens for each retrofi tting technique. The study confi rmed that either RC jacketing or the installation of wing walls with two different structural details can effectively improve the stiffness and strength of an existing column. RC jacketing shows a better improvement in energy dissipation and ductility when compared to the columns with wing walls installed. This is because the two RC jacketed columns experienced a fl exural failure, while a shear failure was found in the two columns with the wing walls installed, and thus led to a drastic decrease of the maximum lateral strengths and ductility. Since many factors may affect the installation of a post-installed anchor, it is better to use standard hooks to replace post-installed anchors in some specifi c points when using RC jacketing or installing wing walls.     

Seismic retrofi tting of RC columns with RC jackets and wing walls with different structural details

An original reinforced concrete(RC) column and four strengthened specimens, two with RC jackets and two with wing walls, were tested in this study. The original column specimen was designed to comply with older(pre-1999) design standards so that the usual detailing defi ciencies in existing school buildings in Taiwan could be simulated. Two different structural details were chosen to fabricate the full-scale specimens for each retrofi tting technique. The study confi rmed that either RC jacketing or the installation of wing walls with two different structural details can effectively improve the stiffness and strength of an existing column. RC jacketing shows a better improvement in energy dissipation and ductility when compared to the columns with wing walls installed. This is because the two RC jacketed columns experienced a fl exural failure, while a shear failure was found in the two columns with the wing walls installed, and thus led to a drastic decrease of the maximum lateral strengths and ductility. Since many factors may affect the installation of a post-installed anchor, it is better to use standard hooks to replace post-installed anchors in some specifi c points when using RC jacketing or installing wing walls.     

Probabilistic performance assessment of low‐ductility reinforced concrete frames retrofitted with dissipative braces

The paper illustrates a probabilistic methodology for assessing the vulnerability of existing reinforced concrete (RC) buildings with limited ductility capacity retrofitted by means of dissipative braces. The aim is to highlight the most important parameters controlling the capacity of these coupled systems and specific aspects concerning the response uncertainties. The proposed methodology is based on the use of local engineering demand parameters for monitoring the seismic response and on the development of component and system fragility curves before and after the retrofit. In the first part of the paper, the methodology is illustrated by highlighting its advantages with respect to the existing approaches. Then, its capability and effectiveness are tested by considering a benchmark two‐dimensional RC frame designed for gravity‐loads only. The frame is retrofitted by introducing elasto‐plastic dissipative braces designed for different levels of base shear capacity. The obtained results show the effectiveness of the methodology in describing the changes in the response and in the failure modalities before and after the retrofit, for different retrofit levels. Moreover, the retrofit effectiveness is evaluated by introducing proper synthetic parameters describing the fragility curves and by stressing the importance of employing local engineering demand parameters (EDPs) rather than global EDPs in the seismic risk evaluation of coupled systems consisting in low‐ductility RC frames and dissipative braces. Copyright © 2012 John Wiley & Sons, Ltd.     

RC buildings retrofitted by converting frame bays into RC walls

Adding concrete walls by infilling certain frame bays with reinforced concrete is popular for seismic retrofitting, but is covered by codes only if the connection of the old concrete to the new ensures monolithic behavior. To avoid penalizing the foundation of the new wall with a very high moment resistance, the new concrete should not be thicker than, or surround, the old frame members. A cost-effective connection of these members to a thin new web is proposed, alongside a design procedure and detailing that conform to current codes. Owing to practical difficulties, footings of added walls are often small and weakly connected to the other footings, hence they uplift and rock during the earthquake. The model for uplift of 3D footings consists of two pairs of nonlinear-elastic springs in a cross layout and approximates also moderate nonlinearities in the soil continuum. It is used in nonlinear, static or dynamic, analyses of three buildings with added walls. The analyses of a clean, regular 4-story building show the benefit from uplift to the added walls and a certain adverse effect on some columns but not on beams, as well as the lack of a clear positive effect of tie-beams. The application to a 7-story and a 2-story real building with extreme, yet typical, irregularities in plan and elevation exemplifies the real-life restrictions in the use of added walls and shows their limits for the improvement of seismic performance; certain deficiencies in flexure or shear remain in both and are corrected at very low cost with local fiber reinforced polymer (FRP) jackets without new analysis of the building, as FRPs do not change the member effective stiffness or moment resistance.     

纤维加固混凝土圆截面短柱抗震性能试验研究

通过对3根抗剪不足的混凝土圆截面短柱的拟静力试验,不仅验证了横向包裹的碳纤维布能提高短柱的抗剪承载力,改善混凝土的变形性能,从而提高短柱的抗震性能,同时验证了具有一定破损的短柱经碳纤维布强约束加固后,同样具有良好的抗震性能。文章最后对碳纤维布加固短柱的延性提高机理进行了分析。     

Damage assessment for seismic response of recycled concrete filled steel tube columns

A model for evaluating structural damage of recycled aggregate concrete filled steel tube (RCFST) columns under seismic effects is proposed in this paper. The proposed model takes the lateral deformation and the effect of repeated cyclic loading into account. Available test results were collected and utilized to calibrate the parameters of the proposed model. A seismic test for six RCFST columns was also performed to validate the proposed damage assessment model. The main test parameters were the recycled coarse aggregate (RCA) replacement percentage and the bond-slip property. The test results indicated that the seismic performance of the RCFST member depends on the RCA contents and their damage index increases as the RCA replacement percentage increases. It is also indicated that the damage degree of RCFST changes with the variation of the RCA replacement percentage. Finally, comparisons between the RCA contents, lateral deformation ratio and damage degree were implemented. It is suggested that an improvement procedure should be implemented in order to compensate for the performance difference between the RCFST and normal concrete filled steel tubes (CFST).     

Probabilistic seismic performance evaluation of SMA-braced steel frames considering SMA brace failure

This study explores seismic performance of steel frame buildings with SMA-based self-centering bracing systems using a probabilistic approach. The self-centering bracing system described in this study relies on superelastic response of large-diameter cables. The bracing systems is designed such that the SMA cables are always stressed in tension. A four-story steel frame building characterized until collapse in previous research is selected as a case-study building. The selected steel frame building is designed with SMA bracing systems considering various design parameters for SMA braces. Numerical models of these buildings are developed by taking into account the ultimate state of structural components and SMA braces as well as the effect of gravity frames on lateral load resistance. Nonlinear static analyses are conducted to assess the seismic characteristics of each frame and to examine the effect of SMA brace failure on the seismic load carrying capacity of SMA-braced frames. Incremental dynamic analyses (IDA) are performed to compute seismic response of the designed frames at various seismic intensity levels. The results of IDA are used to develop probabilistic seismic demand models for peak inter-story and residual inter-story drifts. Seismic demand hazard curves of peak and residual inter-story drifts are generated by convolving the ground motion hazard with the probabilistic seismic demand models. Results show that steel frames designed with SMA bracing systems provide considerably lower probability of reaching at a damage state level associated with residual drifts compared to a similarly designed steel moment resisting frame, especially for seismic events with high return periods. This indicates reduced risks for the demolition and collapse due to excessive residual drifts for SMA braced steel frames.     

型钢高强混凝土柱抗震性能的试验研究

通过14根型钢高强混凝土柱的低周反复加载试验，得到了型钢高强混凝土柱在压、弯、剪共同作用下的主要破坏形态，并探讨了剪跨比、配箍率、混凝土强度对型钢高强混凝土柱滞回曲线、耗能能力以及延性的影响。试验结果表明，型钢高强混凝土柱具有抵御二次地震作用的能力，其抗震性能优于钢筋混凝土柱。     

基于IDA的套箍加固拱上立柱抗震性能评估

以德阳金花大桥为工程实例,结合拱上立柱的实际震害,利用地震作用下的非线性计算模型,建立基于IDA的钢筋混凝土套箍加固拱上立柱抗震性能评估分析方法.通过分析表明,剪跨比对拱上立柱的抗震性能影响显著,高剪跨比立柱抗震性能相对较差,在地震作用下拱上立柱为易损构件;套箍加固拱上立柱的抗震性能提高明显,易损性显著降低,延性亦有一...     

Numerical evaluation of seismic response of soft-story RC frames retrofitted with passive devices

This study presents a nonlinear modelling technique for reinforced concrete (RC) frames retrofitted with metallic yielding devices to predict the seismic response using a computer software OpenSees. The numerical model considers the axial–flexure interaction, shear force–displacement response and the bond-slip characteristics of the frame members. The predicted hysteretic response has been compared with the results of slow-cyclic testing. The validated numerical model is then used to predict the seismic response of a five-story RC frame with soft-story. Nonlinear cyclic pushover and dynamic analyses are conducted to investigate the effectiveness of the proposed retrofitting scheme in enhancing the lateral strength and energy dissipation potential and in controlling the premature failure of the study frame. Analysis results showed significant improvement in the seismic response of RC frames with soft-story using the proposed retrofitting technique.     

Displacement-based design of RC bridge columns in seismic regions

This paper presents a seismic design philosophy based on displacements rather than forces. By inverting the seismic design process, a rational method is established where member strength and stiffness depend on the target displacement. A comprehensive procedure for displacement-based design of cantilever bridge columns is presented and verified by dynamic inelastic time history analysis. Parameter studies are used to examine the influence of several variables within the possible design solution space.     

Numerical models of RC elements and their impacts on seismic performance assessment

This paper aims to provide a guideline for numerical modeling of reinforced concrete (RC) frame elements for the seismic performance assessment of a structure. Several types of numerical models of RC frame elements are available in nonlinear structural analysis packages. Because the numerical models are formulated based on different assumptions and theories, the models' accuracy, computing time, and applicability vary, which poses a great difficulty to practicing engineers and limits their confidence in the analysis results. In this study, the applicability of five representative numerical models of RC frame elements is evaluated through comparison with 320 experimental results available from the Pacific Earthquake Engineering Research column database. The accuracy of a numerical model is evaluated according to its initial stiffness, peak strength, and energy dissipation capacity of the global responses. In addition, a parametric study of a cantilever RC column subjected to earthquake excitation is carried out to systematically evaluate the consequence of the adopted numerical models on the maximum inelastic structural responses. It is found from this study that the accuracy of the numerical models is sensitive to shear force demand–capacity ratio. If a structural period is short and the structure is shear critical, the use of numerical models that can explicitly capture the shear deformation and failure is suggested. If the structural period is long, the selection of a numerical model does not greatly influence the global response of the structure. The paper also presents statistical parameters of each numerical model, which can be used for probabilistic seismic performance assessment. Copyright © 2014 John Wiley & Sons, Ltd.     

Probabilistic estimate of seismic response design values of RC frames

Probabilistically controlled design values of the nonlinear seismic response of reinforced concrete frames are obtained using a method previously proposed by the authors. The method allows to calculate conservative design values characterized by a predefined non‐exceedance probability, using a limited number of spectrum‐fitting generated accelerograms. Herein the method is applied to elastic‐strain hardening single degree of freedom systems representative of RC framed structures and is then assessed with reference to four reinforced concrete model frames designed according to EC8. The frames are characterized by different natural periods and aspect ratios. The results, compared with those obtained applying current EC8 recommendations, show the effectiveness of the proposed method. EC8 provides for design values of the seismic response of a structure with a nonlinear behavior computed as the mean value of the responses to seven accelerograms or as the maximum value of the responses to three accelerograms. These two criteria lead to design values characterized by very different and uncontrolled non‐exceedance probability levels, while the proposed method allows the analyst to directly control the non‐exceedance probability level of the calculated design values. Copyright © 2009 John Wiley & Sons, Ltd.     

Probabilistic seismic hazard assessment for Thailand

A set of probabilistic seismic hazard maps for Thailand has been derived using procedures developed for the latest US National Seismic Hazard Maps. In contrast to earlier hazard maps for this region, which are mostly computed using seismic source zone delineations, the presented maps are based on the combination of smoothed gridded seismicity, crustal-fault, and subduction source models. Thailand’s composite earthquake catalogue is revisited and expanded, covering a study area limited by 0°–30°N Latitude and 88°–110°E Longitude and the instrumental period from 1912 to 2007. The long-term slip rates and estimates of earthquake size from paleoseismological studies are incorporated through a crustal fault source model. Furthermore, the subduction source model is used to model the megathrust Sunda subduction zones, with variable characteristics along the strike of the faults. Epistemic uncertainty is taken into consideration by the logic tree framework incorporating basic quantities, such as different source modelling, maximum cut-off magnitudes and ground motion prediction equations. The ground motion hazard map is presented over a 10 km grid in terms of peak ground acceleration and spectral acceleration at 0.2, 1.0, and 2.0 undamped natural periods and a 5% critical damping ratio for 10 and 2% probabilities of exceedance in 50 years. The presented maps give expected ground motions that are based on more extensive data sources than applied in the development of previous maps. The main findings are that northern and western Thailand are subjected to the highest hazard. The largest contributors to short- and long-period ground motion hazard in the Bangkok region are from the nearby active faults and Sunda subduction zones, respectively.     

基于OpenSees的CFRP加固RC短柱抗震性能数值模拟

采用地震工程开源模拟软件OpenSees对CFRP加固RC短柱进行了静力Push over分析和低周往复加载分析,并与通用有限元软件ANSYS模拟结果进行对比研究.研究结果表明:利用CFRP进行加固,不仅阻止了RC短柱的脆性剪切破坏,而且使破坏模式转化为延性弯曲破坏,增强了结构延性,进而有效地提高其抗震性能;同ANSYS相比,OpenSees可以宏观的反映CFRP与混凝土共同作用的非线性力学特征,有效地对构件和结构进行加固后的承载力及抗震性能分析.