A storm event watershed model for surface runoff based on 2D fully dynamic wave equations

The main purpose of this work concerns the development and testing of an overland flow model based on the two‐dimensional fully dynamic shallow water equations. Three key aspects, fundamental to get accurate, efficient and robust computation of surface runoff at basin scale, are discussed by transferring the main findings obtained by the recent research on the topic of dam‐break wave and flood propagation in the context of rainfall–runoff modelling. In particular, attention is focused on the numerical flux and bottom slope source terms computation, on a numerical treatment of friction slope terms and on an algorithm for dealing with wetting/drying fronts. The performances of the numerical model have been preliminarily evaluated using experimental or ideal tests characterized by very critical conditions for the stability of a numerical model. Then, attention was focused on a real event occurred in a sub‐basin of Reno river in Italy to analyse the suitability of the model in simulating real flood situations. The numerical results highlight the good performances of the model in all the simulations discussed in the paper. Copyright © 2012 John Wiley & Sons, Ltd.     

Flow convergence over a broad,flat continental shelf

The broad (～500 km) southeastern Bering Sea continental shelf contains three fronts; outer (shelf break, ～170-m depth), middle (～100-m depth), and inner (～50-m depth). The shelf break and inner fronts appear to be analogous to similar fronts reported from other mid-latitude continental shelves; extensively studied examples are from the mid-Atlantic bight, off Nova Scotia, and around the British Isles. The middle front may have counterparts on the broad North Sea and East China Sea shelves.One-month current and temperature records from either side of the middle front, ～150 km landward from the shelf break, showed convergence in the layers deeper than 30 m in both the cross-shelf flow field and heat flux. The convergence was ～3 cm s^?1, so an average upwelling at ～1 × 10^?3cm s^?1 and divergence in the surface layer were required to maintain continuity. Variations in the degree of convergence arose primarily from 1 to 5-day fluctuations in sub-tidal flow across the outer shelf domain seaward of the front.Diffusive landward heat flux was dominated by tidal scales. Horizontal eddy conductivities describing the flux were ～1 ? 10⁶ on the landward side and ～5 × 10⁶cm² s^?1 on the seaward side, and were less in the layers above the bottom layer. Advective flux by the mean flow was the same order as diffusive flux, but landward in the bottom layer and seaward in the mid-water column layers, in agreement with deductions from water mass analyses. Frontal effects reduced the net cross-shelf heat flux beneath ～30 m by about 50%. The observation of a flow convergence in the middle of a broad, flat continental shelf poses an important question of dynamics.     

A robust well-balanced finite volume model for shallow water flows with wetting and drying over irregular terrain

An unstructured Godunov-type finite volume model is developed for the numerical simulation of geometrically challenging two-dimensional shallow water flows with wetting and drying over convoluted topography. In the framework of sloping bottom model, a modified formulation of shallow water equations is used to preserve mass conservation during flooding and recession. The key ingredient of the model is the use of this combination of the sloping bottom model and the modified shallow water equations to provide a robust technique for wet/dry fronts tracking and, together with centered discretization of the bed slope source term, to exactly preserve the static flow on irregular topographies. The variable reconstruction technique ensures nonnegative reconstructed water depth and reasonable reconstructed velocity, and the friction terms are solved by semi-implicit scheme that does not invert the direction of velocity components. The robustness and accuracy of the proposed model are assessed by comparing numerical and reference results of extensive test cases. Moreover, the results of a dam-break flooding over real topography are presented to show the capability of the model on field-scale application.     

Effects of sediment load on hydraulics of overland flow on steep slopes

Eroded sediment may have significant effects on the hydraulics of overland flow, but few studies have been performed to quantify these effects on steep slopes. This study investigated the potential effects of sediment load on Reynolds number, Froude number, flow depth, mean velocity, Darcy–Weisbach friction coefficient, shear stress, stream power, and unit stream power of overland flow in a sand‐glued hydraulic flume under a wide range of hydraulic conditions and sediment loads. Slope gradients were varied from 8·7 to 34·2%, unit flow rates from 0·66 to 5·26×10^?3 m² s^?1, and sediment loads from 0 to 6·95 kg m^?1 s^?1. Both Reynolds number (Re) and Froude number (Fr) decreased as sediment load increased, implying a decrease in flow turbulence. This inverse relationship should be considered in modeling soil erosion processes. Flow depth increased as sediment load increased with a mean value of 1·227 mm, caused by an increase in volume of sediment‐laden flow (contribution 62·4%) and a decrease in mean flow velocity (contribution 37·6%). The mean flow velocity decreased by up to 0·071 m s^?1 as sediment load increased. The Darcy–Weisbach friction coefficient (f) increased with sediment load, showing that the total energy consumption increased with sediment load. The effects of sediment load on f depended on flow discharge: as flow discharge increased, the influence of sediment load on f decreased due to increased flow depth and reduced relative roughness. Flow shear stress and stream power increased with sediment load, on average, by 80·5% and 60·2%, respectively; however, unit stream power decreased by an average of 11·1% as sediment load increased. Further studies are needed to extend and apply the insights obtained under these controlled conditions to real‐world overland flow conditions. Copyright © 2010 John Wiley & Sons, Ltd.     

Dynamic response of debris flows impacting curved joint check dams

The dynamic impact force of debris flow on dams with a curved upstream face curved was investigated using laboratory experiments and a theoretical approach. Equations describing the impact force and maximum run-up height were derived. The experiments and theoretical considerations reveal that the impact force and maximum run-up height are mainly controlled by the Froude number (Fr) reduced by the cosine of the channel slope angle (cosα). Both the impact force and the maximum run-up height have a quadratic relation with the modified Froude number (Fr/(cosα)^0.5). The experimental data and the results of the theoretical approach are in good agreement, indicating that the theoretical approach can be used in practical applications. It is concluded that the comparison between the curved-joint dam and the more conventional sharp-joint dam shows no differences in the maximum impact force and run-up height for the same modified Froude number. With the sharp-joint dam, the peak values of the impact force are reached more quickly than with the curved-joint dam.     

Reconstructing historic Glacial Lake Outburst Floods through numerical modelling and geomorphological assessment: Extreme events in the Himalaya

Recession of high‐mountain glaciers in response to climatic change frequently results in the development of moraine‐dammed glacial lakes. Moraine dam failure is often accompanied by the release of large volumes of water and sediment, termed a Glacial Lake Outburst Flood (GLOF). Chukhung Glacier is a small (~3 km²) receding valley glacier in Mt. Everest (Sagarmatha) National Park, Nepal. Unlike many Himalayan glaciers, which possess a thick mantle of supraglacial debris, its surface is relatively clean. The glacier terminus has receded 1.3 km from its maximum Holocene position, and in doing so provided the space for an ice‐contact moraine‐dammed lake to develop. The lake had a maximum volume of 5.5 × 10⁵ m³ and drained as a result of breaching of the terminal moraine. An estimated 1.3 × 10⁵ m³ of material was removed from the terminal moraine during breach development. Numerical dam‐breach modelling, implemented within a Generalised Likelihood Uncertainty Estimation (GLUE) framework, was used to investigate a range of moraine‐dam failure scenarios. Reconstructed outflow peak discharges, including failure via overtopping and piping mechanisms, are in the range 146–2200 m³ s^‐1. Results from two‐dimensional hydrodynamic GLOF modelling indicate that maximum local flow depths may have exceeded 9 m, with maximum flow velocities exceeding 20 m s^‐1 within 700 m of the breach. The floodwaters mobilised a significant amount of material, sourced mostly from the expanding breach, forming a 300 m long and 100 m wide debris fan originating at the breach exit. moraine‐dam. These results also suggest that inundation of the entire floodplain may have been achieved within ten minutes of initial breach development, suggesting that debris fan development was rapid. We discuss the key glaciological and geomorphological factors that have determined the evolution of a hazardous moraine‐dammed lake complex and the subsequent generation of a GLOF and its geomorphological impact. © 2014 The Authors. Earth Surface Processes and Landforms published by John Wiley & Sons Ltd.     

Numerical resolution of well-balanced shallow water equations with complex source terms

This paper presents a well-balanced numerical scheme for simulating frictional shallow flows over complex domains involving wetting and drying. The proposed scheme solves, in a finite volume Godunov-type framework, a set of pre-balanced shallow water equations derived by considering pressure balancing. Non-negative reconstruction of Riemann states and compatible discretization of slope source term produce stable and well-balanced solutions to shallow flow hydrodynamics over complex topography. The friction source term is discretized using a splitting implicit scheme. Limiting value of the friction force is derived to ensure stability. This new numerical scheme is validated against four theoretical benchmark tests and then applied to reproduce a laboratory dam break over a domain with irregular bed profile.     

Persistence of road runoff generation in a logged catchment in Peninsular Malaysia

Measurements of saturated hydraulic conductivity (K_s) and diagnostic model simulations show that all types of logging road/trail in the 14·4 ha Bukit Tarek Experimental Catchment 3 (BTEC3) generate substantial Horton overland flow (HOF) during most storms, regardless of design and level of trafficking. Near‐surface K_s(0–0·05 m) on the main logging road, skid trails and newly constructed logging terraces was less than 1, 2 and 34 mm h^?1, respectively. Near‐surface K_s on an abandoned skid trail in an adjacent basin was higher (62 mm h^?1), owing to the development of a thin organic‐rich layer on the running surface over the past 40 years. Saturated hydraulic conductivity measured at 0·25 m below the surface of all roads was not different (all <6 mm h^?1) and corresponded to the K_s of the adjacent hillslope subsoil, as most roads were excavated into the regolith more than 0·5–1 m. After 40 years, only limited recovery in near‐surface K_s occurred on the abandoned skid trail. This road generated HOF after the storage capacity of the upper near‐surface layer was exceeded during events larger than about 20 mm. Thus, excavation into low‐K_s substrate had a greater influence on the persistence of surface runoff production than did surface compaction by machinery during construction and subsequent use during logging operations. Overland flow on BTEC3 roads was also augmented by the interception of shallow subsurface flow traveling along the soil–saprolite/bedrock interface and return flow emerging from the cutbank through shallow biogenic pipes. The most feasible strategy for reducing long‐term road‐related impacts in BTEC3 is limiting the depth of excavation and designing a more efficient road network, including minimizing the length and connectivity of roads and skid trails. Copyright © 2007 John Wiley & Sons, Ltd.     

Percolation losses in paddy fields with a dynamic soil structure: model development and applications

The hydraulic characteristics of the plough pan of paddy fields provide continuous ponding conditions during the growing season and control the water use efficiency in wet rice production. Its saturated hydraulic conductivity K_s, however, exhibits a large spatiotemporal variability as a consequence of a highly dynamic soil structure involving temporary shrinkage cracks. Water flow through the earthen bunds surrounding the fields further contributes to the uncertainty in water flux calculations. The objective of this study was to develop a simple deterministic model with stochastic elements (‘PADDY‐FLUX’) for depiction of deep percolation, and to assess the effect of different water management scenarios on percolation in two channel command areas. Darcy's law is used as the fundamental equation for water flow calculations with the ponding water depth h as a time‐dependent variable. Flux uncertainty is estimated by a Monte‐Carlo‐type implementation. K_s is treated as a random variable of a bimodal probability density function (PDF), which is the weighted sum of two Gaussian PDFs (accounting for a matrix and a preferential flow domain). The weighing factor α is a function of h, reflecting an increasing risk for preferential flow situations after desiccation and the development of shrinkage cracks. Under‐bund percolation is calculated using transfer functions. The results demonstrate that percolation losses increase in the following order: continuous soil saturation < continuous flooding (CF) < mid‐season drainage and intermittent irrigation (MD + II) < mid‐season drainage and continuous flooding. The bunds contribute up to 54 and 17% to total fluxes under CF and MD + II, respectively. Preferential water fluxes are responsible for the major part of water losses as soon as desiccation causes the formation of shrinkage cracks. As a conclusion, continuous soil saturation should be promoted as the least water‐intensive irrigation regime, while intermittent irrigation is recommended only in case that irreversible shrinkage cracks have already developed. Copyright © 2010 John Wiley & Sons, Ltd.     

Infiltration and runoff generation processes in fire‐affected soils

Post‐wildfire runoff was investigated by combining field measurements and modelling of infiltration into fire‐affected soils to predict time‐to‐start of runoff and peak runoff rate at the plot scale (1 m²). Time series of soil‐water content, rainfall and runoff were measured on a hillslope burned by the 2010 Fourmile Canyon Fire west of Boulder, Colorado during cyclonic and convective rainstorms in the spring and summer of 2011. Some of the field measurements and measured soil physical properties were used to calibrate a one‐dimensional post‐wildfire numerical model, which was then used as a ‘virtual instrument’ to provide estimates of the saturated hydraulic conductivity and high‐resolution (1 mm) estimates of the soil‐water profile and water fluxes within the unsaturated zone. Field and model estimates of the wetting‐front depth indicated that post‐wildfire infiltration was on average confined to shallow depths less than 30 mm. Model estimates of the effective saturated hydraulic conductivity, K_s, near the soil surface ranged from 0.1 to 5.2 mm h^?1. Because of the relatively small values of K_s, the time‐to‐start of runoff (measured from the start of rainfall), t_p, was found to depend only on the initial soil‐water saturation deficit (predicted by the model) and a measured characteristic of the rainfall profile (referred to as the average rainfall acceleration, equal to the initial rate of change in rainfall intensity). An analytical model was developed from the combined results and explained 92–97% of the variance of t_p, and the numerical infiltration model explained 74–91% of the variance of the peak runoff rates. These results are from one burned site, but they strongly suggest that t_p in fire‐affected soils (which often have low values of K_s) is probably controlled more by the storm profile and the initial soil‐water saturation deficit than by soil hydraulic properties. Published 2013. This article is a U.S. Government work and is in the public domain in the USA.     

Characterizing the hydraulic properties of unsaturated sand considering various porosities and drying‐wetting paths of the retention curve

Previous studies have shown that water retention curve (WRC) and the hydraulic conductivity vary because of changes of the void ratio or porosity of soil. However, limited documents pointed out the change of hydraulic properties of soil when compacted to different porosities while considering both of the drying and wetting processes of the WRC. This information is sometimes necessary for research like finger flow analysis or the occurrence of wetting and drying cycles as what would be seen in the field. Therefore, this study aims to examine the change of WRC characteristics with varied porosity considering both of the drying and wetting path in WRC by conducting a sand box experiment. Results show that the same type of sand compacted to various porosities have different hydraulic parameters. Hydraulic conductivities generally decrease with reduced porosities; shape parameter α of the van Genuchten equation (1980) linearly decreases with declining porosity and shape parameter n in a reversal manner for the sands of interest whether in the drying process or wetting process. The unsaturated properties of sand are further characterized by inspecting the variations of moisture content, matric suction and vertical displacement of soil body subject to periodic changes of the water level by another sand box experiment. The outcomes suggest that the saturated water content and residual water content are changing during the wetting–drying process, which can be an implication of the changed properties of WRC. The characteristics of volumetric deformation might be varied as well because of the observation of the dissimilar patterns of the changing vertical displacements among each wetting–drying process. Infiltration patterns of the sands also are identified through numerical modelling by introducing a constant infiltration flux from the surface followed by a no‐influx condition. Results indicate that less water accumulates in the sand near the surface for the sand compacted to higher porosity, but water can move deeper. Hydraulic conductivity is found as the prime factor dominating the evolvement of wetting fronts. However, shape parameters of water retention curves also affect the infiltration pattern to some extent. In addition, different sands with similar porosities can have quite different infiltrating characteristics. Copyright © 2012 John Wiley & Sons, Ltd.     

Flooding and geomorphic impacts in a mountain torrent: Raise Beck,central Lake District,England

Raise Beck is a mountain torrent located in the central Lake District fells, northern England (drainage area of 1·27 km²). The torrent shows evidence of several major flood events, the most recent of which was in January 1995. This event caused a major channel avulsion at the fan apex diverting the main flood flow to the south, blocking the A591 trunk road and causing local flooding. The meteorological conditions associated with this event are described using local rainfall records and climatic data. Records show 164 mm of rainfall in the 24 hours preceding the flood. The peak flood discharge is reconstructed using palaeohydrological and rainfall–runoff methods, which provide discharge values of 27–74 m³ s^?1, and 4–6 m³ s^?1, respectively. The flood transported boulders with b‐axes up to 1400 mm. These results raise some important general questions about flood estimation in steep mountain catchments. The geomorphological impact of the event is evaluated by comparing aerial photographs from before and after the flood, along with direct field observations. Over the historical timescale the impact and occurrence of flooding is investigated using lichenometry, long‐term rainfall data, and documentary records. Two major historical floods events are identified in the middle of the nineteenth century. The deposits of the recent and historical flood events dominate the sedimentological evidence of flooding at Raise Beck, therefore the catchment is sensitive to high magnitude, low frequency events. Following the 1995 flood much of the lower catchment was channelized using rip‐rap bank protection, re‐establishing flow north towards Thirlmere. The likely success of this management strategy in containing future floods is considered, based on an analysis of channel capacities. It is concluded that the channelization scheme is only a short‐term solution, which would fail to contain the discharge of an event equivalent to the January 1995 flood. Copyright © 2002 John Wiley & Sons, Ltd.     

Spatial and temporal perspectives on spring break‐up flooding in the Slave River Delta,NWT

Spatial and temporal patterns of spring break‐up flooding in the Slave River Delta (SRD), Northwest Territories, are characterized during three years (2003–2005) using water isotope tracers and total inorganic suspended sediment (TSS) concentrations measured from lakewater samples collected shortly after the spring melt. Strongly contrasting spring melt periods led to a moderate flood in 2003, no flooding in 2004 and widespread flooding in 2005. Flooded lakes have isotopically‐depleted δ¹⁸O (δ²H) signatures, ranging between ? 19·2‰ (?145‰) and ? 17·1‰ (?146‰) and most have high TSS concentrations (>10 mg L^?1), while non‐flooded lakes have more isotopically‐enriched δ¹⁸O (δ²H) signatures, ranging between ? 18·2‰ (?149‰) and ? 10·6‰ (?118‰) and low TSS concentrations (<10 mg L^?1). These results, in conjunction with the isotopic signatures of Slave River water and snowmelt, are used to estimate the proportion of river‐ or snowmelt‐induced dilution in delta lakes during the spring of each study year. Calculations indicate river flooding caused dilution of ～70–100% in delta lakes, while snowmelt dilution in the absence of river flooding ranged from ～0–56%. A positive relationship exists between the spatial extent of spring flooding in the SRD and level and discharge on the Slave River and upstream tributaries, suggesting that upstream flow generation plays a key role in determining the magnitude of spring flooding in the SRD. Parallel variations in the 46‐year instrumental Slave River discharge record and flood stratigraphy in the active delta indicate that there is potential for extending the flood history of the SRD, a development that will contribute to a more robust understanding of the drivers of historic, contemporary and future flood frequency in the delta. Copyright © 2008 John Wiley & Sons, Ltd.     

Root properties of vegetation communities and their impact on the erosion resistance of river dikes

Predicted climate change and the associated sea level rise poses an increased threat of flooding due to wave overtopping events at sea and river dikes. To safeguard the land from flooding it is important to keep the soil erosion resistance at the dikes high. As plant roots can be very effective in reducing soil erosion rates by concentrated flow, the main goal of this study is to explore the variability in root system characteristics of five dike vegetation communities along the Scheldt River (Belgium) and to assess their effectiveness in controlling soil erosion rates during concentrated flow. This study is the first one to investigate systematically the erosion‐reducing potential of the root properties of representative dike vegetation communities in a temperate humid climate. Results show that the presence of Urtica dioica resulted in large differences in root length density (RLD) among dike vegetation communities. Observed RLD values in the topsoil ranged from 129 to 235 km m^‐3 for dike vegetation communities without U. dioica, while smaller values ranging from 22 to 58 km m^?3 were found for vegetation communities with U. dioica. The erosion‐reducing effect of the dike vegetation communities was estimated based on a global Hill curve model, linking the RLD to the soil detachment ratio (SDR; i.e. the ratio of the soil detachment rate for root‐permeated topsoils to the soil detachment rate for root‐free topsoils). Concentrated flow erosion rates are likely to be reduced to 13–16% of the erosion rates for root‐free topsoils if U. dioica is absent compared to 22–30% for vegetation communities with U. dioica. Hence, to maintain a high resistance of the soil against concentrated flow erosion it is important to avoid the overgrowth of grassland by U. dioica through an effective vegetation management. Copyright © 2016 John Wiley & Sons, Ltd.     

The 1975 sub-terminal lavas, mount etna: a case history of the formation of a compound lava field

The 1975 sub-terminal activity was characterised by low effusion rates (0.3–0.5 m³ s⁻¹) and the formation of a compound lava field composed of many thousands of flow units. Several boccas were active simultaneously and effusion rates from individual boccas varied from about 10⁻⁴ to 0.25 m³s⁻¹. The morphology of lava flows was determined by effusion rate (E): aa flows with well-developed channels and levees formed when E > 2 × 10⁻³ m³ s⁻¹, small pahoehoe flows formed when 2 × 10⁻³ m³ s⁻¹ >E > 5 > 10⁻⁴ m³ s⁻¹ and pahoehoe toes formed when E < 5 × 10⁻⁴ m³ s⁻¹. There was very little variation with time in the effusion temperature, composition or phenocryst content of the lava.New boccas were commonly formed at the fronts of mature lava flows which had either ceased to flow or were moving slowly. These secondary boccas developed when fluid lava in the interior of mature aa flows either found a weakness in the flow front or was exposed by avalanching of the moving flow front. The resulting release of fluid lava was accompanied by either partial drainage of the mature flow or by the formation of a lava tube in the parent flow. The temperature of the lava forming the new bocca decreased with increasing distance from the source bocca (0.035°C m⁻¹). It is demonstrated from the rate of temperature decrease and from theoretical considerations that many of the Etna lavas still contained a substantial proportion of uncooled material in their interior as they came to rest. The formation of secondary boccas is postulated to be one reason why direct measurements of effusion rates tend, in general, to overestimate the total effusion rates of sub-terminal Etna lava fields.     

Characterization of hydraulic suitability of Chinese sturgeon (Acipenser sinensis) spawning habitat in the Yangtze River

Hydrodynamic flow fields affect the ecological processes such as the water diversity and the distribution of organisms. Understanding the hydrodynamic and ecological processes is critical for the restoration and protection of especially fragile ecological habitats in river systems. This study uses turbulent flow to characterize the ecological behaviour of Chinese Sturgeon (Acipenser sinensis) in the Yangtze River. The Delft3D‐Flow model, which is first validated with field‐measured data, is used to simulate the flow field within spawning habitats of Chinese Sturgeon, downstream of Gezhouba Dam. The model‐simulated turbulent kinetic energy (TKE) and its distribution pattern are then used to characterize the hydraulic environment of the fish's spawning habitat. For the spawning habitat, downstream of Gezhouba Dam, the lower limit of TKE for the Chinese Sturgeon egg mass field is 0.025 m²/s², which occurs at a velocity less than 1.7 m/s. Chinese Sturgeon prefers habitats with TKE range of 0.010 ~ 0.015 m²/s² for resting. This suggests that discharge regimes provide the basis for ecological regulation of the Three Gorges Reservoir and the scientific reference for river management. Copyright © 2011 John Wiley & Sons, Ltd.     

The influence of flow discharge variations on the morphodynamics of a diffluence–confluence unit on a large river

Bifurcations are key geomorphological nodes in anabranching and braided fluvial channels, controlling local bed morphology, the routing of sediment and water, and ultimately defining the stability of their associated diffluence–confluence unit. Recently, numerical modelling of bifurcations has focused on the relationship between flow conditions and the partitioning of sediment between the bifurcate channels. Herein, we report on field observations spanning September 2013 to July 2014 of the three‐dimensional flow structure, bed morphological change and partitioning of both flow discharge and suspended sediment through a large diffluence–confluence unit on the Mekong River, Cambodia, across a range of flow stages (from 13 500 to 27 000 m³ s^?1). Analysis of discharge and sediment load throughout the diffluence–confluence unit reveals that during the highest flows (Q = 27 000 m³ s^?1), the downstream island complex is a net sink of sediment (losing 2600 ± 2000 kg s^?1 between the diffluence and confluence), whereas during the rising limb (Q = 19 500 m³ s^?1) and falling limb flows (Q = 13 500 m³ s^?1) the sediment balance is in quasi‐equilibrium. We show that the discharge asymmetry of the bifurcation varies with discharge and highlight that the influence of upstream curvature‐induced water surface slope and bed morphological change may be first‐order controls on bifurcation configuration. Comparison of our field data to existing bifurcation stability diagrams reveals that during lower (rising and falling limb) flow the bifurcation may be classified as unstable, yet transitions to a stable condition at high flows. However, over the long term (1959–2013) aerial imagery reveals the diffluence–confluence unit to be fairly stable. We propose, therefore, that the long‐term stability of the bifurcation, as well as the larger channel planform and morphology of the diffluence–confluence unit, may be controlled by the dominant sediment transport regime of the system. © 2017 The Authors. Earth Surface Processes and Landforms published by John Wiley & Sons Ltd.     

Impacts of sediment load on Manning coefficient in supercritical shallow flow on steep slopes

The Manning equation is one of the most widely used formulae for calculating the velocity of shallow overland flow in hydrological and erosion models. Precise estimation of the Manning's friction coefficient (n) is critical to determining overland flow and soil erosion processes. Few studies have been conducted to quantify the effects of sediment load on Manning's n on steep slopes. This study was conducted to investigate the potential effects of sediment load on Manning's n in a flume with a fixed bed, under wide ranges of hydraulics and sediment loads. Slope gradient varied from 8·7 to 34·2%, unit flow rate from 0·66 to 5·26 × 10^?3 m² s^?1, and sediment load from 0 to 6·95 kg m^?1 s^?1. The Reynolds number ranged from 350 to 5899. Results showed that Manning's n varied in both sediment‐free and sediment‐laden flows ranging from 0·012 to 0·055. The apparent Manning's coefficients of sediment‐laden flow were much greater than those of sediment‐free flow. The mean Manning coefficient of sediment‐laden flow was 51·27% greater than the mean value of sediment‐free flow. For sediment‐laden flow, Manning's n could be estimated with a power function of unit flow discharge and sediment content. Further studies are needed to quantify the potential effects of sediment load on the Manning's n on erodible beds and in fields. Copyright © 2010 John Wiley & Sons, Ltd.     

The seismic signatures of the surge wave from the 2009 Xiaolin landslide‐dam breach in Taiwan

The catastrophic Xiaolin landslide occurred on 9 August 2009, after Typhoon Morakot struck Taiwan. This landslide formed a dam that subsequently breached, burying and flooding the village of Xiaolin. Seismic signals were induced by the landslide and dam breaching and recorded at the Jiaxian broadband seismic station in Taiwan. The time‐frequency spectra for the data from this station were analysed to extract the seismic characteristics of the landslide and to deduce the timing of processes associated with the landslide dam‐break flooding. The duration of the river blockage, the time of the dam breach, the duration of the surge wave and the mean speed of the surge wave were estimated, and the hydrological implications of the flood behaviour were interpreted. The spectral characteristics of the different stream discharges were also studied. Stream water level/discharge is closely related to the frequency of the seismic signals. The broadband stations are particularly useful for flood monitoring due to their ability to continuously record measurements and their high sensitivity. Copyright © 2011 John Wiley & Sons, Ltd.