Remote sensing of a comet at millimeter and submillimeter wavelengths from an orbiting spacecraft

The ESA Rosetta Spacecraft, launched on March 2, 2004 with the ultimate destination being Comet 67P/Churyumov–Gerasimenko, carries a relatively small and lightweight millimeter–submillimeter spectrometer instrument, the first of its kind launched into deep space. The instrument, named Microwave Instrument for the Rosetta Orbiter (MIRO), consists of a 30-cm diameter, offset parabolic reflector telescope, which couples energy in the millimeter and submillimeter bands to two heterodyne receivers. Center-band operating frequencies are near 190 GHz (1.6 mm) and 562 GHz (0.5 mm). Broadband, total power continuum measurements can be made in both bands. A 4096-channel spectrometer with 44 kHz resolution is connected to the submillimeter receiver. The spectral resolution is sufficient to observe individual, thermally broadened spectral lines (T⩾10 K). The submillimeter radiometer/spectrometer is fixed tuned to measure four volatile species—CO, CH₃OH, NH₃ and three isotopes of water, H₂¹⁶O, H₂¹⁷O and H₂¹⁸O. The MIRO experiment will use these species as probes of the physical conditions within the nucleus and coma. The basic quantities measured by MIRO are surface temperature, gas production rates and relative abundances, and velocity and excitation temperature of each species, along with their spatial and temporal variability. This information will be used to infer coma structure and outgassing processes, including the nature of the nucleus/coma interface.     

Identification of Zirconium Oxide molecular lines in the sunspot umbral spectra

The ZrO molecule has been detected in sunspot umbrae through the identification of following laboratory molecular transitions: ¹Σ⁺ ? X¹Σ⁺ (0, 0), A³Φ₂ ? X²Δ₁ (0, 0), A³Φ₃ ? X²Δ₂ (0, 0), A³Φ₄ ? X²Δ₃ (0, 0), B³Π₂ ? X³Δ₃ (0, 0), B³Π₁ ? X³Δ₂ (0, 0) and B³Π₀ ? X³Δ₁ (0, 0) in red – infrared region using high resolution, visible range Fourier Transform Spectrum of sunspot umbra observed at the National Solar Observatory in Kitt Peak (NSO/KP). Much new identification has been made in the searched spectral wavenumber region from 16650 cm^?1 to 18007 cm^?1 of sunspot spectrum. Equivalent widths of well resolved lines, versus rotational quantum number J have been used to determine the effective rotational temperature for seven bands of the ZrO molecule. This result agrees well with the temperatures derived for other molecules’ presence in sunspot umbrae. It is evident that ZrO molecular lines are formed in higher layers of the atmosphere of relatively “cold” sunspots.     

Atomic oxygen on the Venus nightside: Global distribution deduced from airglow mapping

The Visible and Infra-Red Thermal Imaging Spectrometer (VIRTIS) instrument on board the Venus Express spacecraft has measured the O₂(a¹Δ) nightglow distribution at 1.27 μm in the Venus mesosphere for more than two years. Nadir observations have been used to create a statistical map of the emission on Venus nightside. It appears that the statistical 1.6 MR maximum of the emission is located around the antisolar point. Limb observations provide information on the altitude and on the shape of the emission layer. We combine nadir observations essentially covering the southern hemisphere, corrected for the thermal emission of the lower atmosphere, with limb profiles of the northern hemisphere to generate a global map of the Venus nightside emission at 1.27 μm. Given all the O₂(a¹Δ) intensity profiles, O₂(a¹Δ) and O density profiles have been calculated and three-dimensional maps of metastable molecular and atomic oxygen densities have been generated. This global O density nightside distribution improves that available from the VTS3 model, which was based on measurements made above 145 km. The O₂(a¹Δ) hemispheric average density is 2.1 × 10⁹ cm^?3, with a maximum value of 6.5 × 10⁹ cm^?3 at 99.2 km. The O density profiles have been derived from the nightglow data using CO₂ profiles from the empirical VTS3 model or from SPICAV stellar occultations. The O hemispheric average density is 1.9 × 10¹¹ cm^?3 in both cases, with a mean altitude of the peak located at 106.1 km and 103.4 km, respectively. These results tend to confirm the modeled values of 2.8 × 10¹¹ cm^?3 at 104 km and 2.0 × 10¹¹ cm^?3 at 110 km obtained by Brecht et al. [Brecht, A., Bougher, S.W., Gérard, J.-C., Parkinson, C.D., Rafkin, S., Foster, B., 2011a. J. Geophys. Res., in press] and Krasnopolsky [Krasnopolsky, V.A., 2010. Icarus 207, 17–27], respectively. Comparing the oxygen density map derived from the O₂(a¹Δ) nightglow observations, it appears that the morphology is very different and that the densities obtained in this study are about three times higher than those predicted by the VTS3 model.     

Optical constants from 370 nm to 900 nm of Titan tholins produced in a low pressure RF plasma discharge

Determining the optical constants of Titan aerosol analogues, or tholins, has been a major concern for the last three decades because they are essential to constrain the numerical models used to analyze Titan’s observational data (albedo, radiative transfer, haze vertical profile, surface contribution, etc.). Here we present the optical constant characterization of tholins produced with an RF plasma discharge in a (95%N₂–5%CH₄) gas mixture simulating Titan’s main atmospheric composition, and deposited as a thin film on an Al–SiO₂ substrate. The real and imaginary parts, n and k, of the tholin complex refractive index have been determined from 370 nm to 900 nm wavelength using spectroscopic ellipsometry. The values of n decrease from n = 1.64 (at 370 nm) to n = 1.57 (at 900 nm) as well as the values of k which feature two behaviors: an exponential decay from 370 nm to 500 nm, with k = 12.4 × e^?0.018λ (where λ is expressed in nm), followed by a plateau, with k = (1.8 ± 0.2) × 10^?3. The trends observed for the PAMPRE tholins optical constants are compared to those determined for other Titan tholins, as well as to the optical constants of Titan’s aerosols retrieved from observational data.     

Observation of DCl and upper limit to NH3 on Venus

To search for DCl in the Venus atmosphere, a spectrum near the D³⁵Cl (1–0) R4 line at 2141.54 cm^?1 was observed using the CSHELL spectrograph at NASA IRTF. Least square fitting to the spectrum by a synthetic spectrum results in a DCl mixing ratio of 17.8 ± 6.8 ppb. Comparing to the HCl abundance of 400 ± 30 ppb (Krasnopolsky [2010a] Icarus, 208, 314–322), the DCl/HCl ratio is equal to 280 ± 110 times the terrestrial D/H = 1.56 × 10^?4. This ratio is similar to that of HDO/H₂O = 240 ± 25 times the terrestrial HDO/H₂O from the VEX/SOIR occultations at 70–110 km. Photochemistry in the Venus mesosphere converts H from HCl to that in H₂O with a rate of 1.9 × 10⁹ cm^?2 s^?1 (Krasnopolsky [2012] Icarus, 218, 230–246). The conversion involves photolysis of HCl; therefore, the photochemistry tends to enrich D/H in HCl and deplete in H₂O. Formation of the sulfuric acid clouds may affect HDO/H₂O as well. The enriched HCl moves down by mixing to the lower atmosphere where thermodynamic equilibriums for H₂ and HCl near the surface correspond to D/H = 0.71 and 0.74 times that in H₂O, respectively. Time to establish these equilibriums is estimated at ～3 years and comparable to the mixing time in the lower atmosphere. Therefore, the enriched HCl from the mesosphere gives D back to H₂O near the surface. Comparison of chemical and mixing times favors a constant HDO/H₂O up to ～100 km and DCl/HCl equal to D/H in H₂O times 0.74.Ammonia is an abundant form of nitrogen in the reducing environments. Thermodynamic equilibriums with N₂ and NO near the surface of Venus give its mixing ratio of 10^?14 and 6 × 10^?7, respectively. A spectrum of Venus near the NH₃ line at 4481.11 cm^?1 was observed at NASA IRTF and resulted in a two-sigma upper limit of 6 ppb for NH₃ above the Venus clouds. This is an improvement of the previous upper limit by a factor of 5. If ammonia exists at the ppb level or less in the lower atmosphere, it quickly dissociates in the mesosphere and weakly affects its photochemistry.     

The formation heritage of Jupiter Family Comet 10P/Tempel 2 as revealed by infrared spectroscopy

We present spectral and spatial information for major volatile species in Comet 10P/Tempel 2, based on high-dispersion infrared spectra acquired on UT 2010 July 26 (heliocentric distance R_h = 1.44 AU) and September 18 (R_h = 1.62 AU), following the comet’s perihelion passage on UT 2010 July 04. The total production rate for water on July 26 was (1.90 ± 0.12) × 10²⁸ molecules s^?1, and abundances of six trace gases (relative to water) were: CH₃OH (1.58% ± 0.23%), C₂H₆ (0.39% ± 0.04%), NH₃ (0.83% ± 0.20%), and HCN (0.13% ± 0.02%). A detailed analysis of intensities for water emission lines provided a rotational temperature of 35 ± 3 K. The mean OPR is consistent with nuclear spin populations in statistical equilibrium (OPR = 3.01 ± 0.18), and the (1σ) lower bound corresponds to a spin temperature >38 K. Our measurements were contemporaneous with a jet-like feature observed at optical wavelengths. The spatial profiles of four primary volatiles display strong enhancements in the jet direction, which favors release from a localized vent on the nucleus. The measured IR continuum is much more sharply peaked and is consistent with a dominant contribution from the nucleus itself. The peak intensities for H₂O, CH₃OH, and C₂H₆ are offset by ～200 km in the jet direction, suggesting the possible existence of a distributed source, such as the release of icy grains that subsequently sublimed in the coma. On UT September 18, no obvious emission lines were present in our spectra, nevertheless we obtained a 3σ upper limit Q(H₂O) < 2.86 × 10²⁷ molecules s^?1.     

Characterizing Io’s Pele,Tvashtar and Pillan plumes: Lessons learned from Hubble

Hubble Space Telescope/Wide Field and Planetary Camera 2 (HST/WFPC2) images of Io obtained between 1995 and 2007 between 0.24 and 0.42 μm led to the detection of the Pele plume in reflected sunlight in 1995 and 1999; imaging of the Pele plume via absorption of jovian light in 1996 and 1999; detection of the Prometheus-type Pillan plume in reflected sunlight in 1997; and detection of the 2007 Pele-type Tvashtar plume eruption in reflected sunlight and via absorption of jovian light. Based on a detailed analysis of these observations we characterize and compare the gas and dust properties of each of the detected plumes. In each case, the brightness of the plumes in reflected sunlight is less at 0.26 μm than at 0.33 μm. Mie scattering analysis of the wavelength dependence of each plume’s reflectance signature suggests that range of particle sizes within the plumes is quite narrow. Assuming a normal distribution of particle sizes, the range of mean particle sizes is ～0.035–0.12 μm for the 1997 Pillan eruption, ～0.05–0.08 μm for the 1999 Pele and 2007 Tvasthar plumes, and ～0.05–0.11 μm for the 1995 Pele plume, and in each case the standard deviation in the particle size distribution is <15%. The Mie analysis also suggests that the 2007 Tvashtar eruption released ～10⁹ g of sulfur dust, the 1999 Pele eruption released ～10⁹ g of SO₂ dust, the 1997 Pillan eruption released ～10¹⁰ g of SO₂ dust, and the 1995 Pele plume may have released ～10¹⁰ g of SO₂ dust. Analysis of the plume absorption signatures recorded in the F255W filter bandpass (0.24–0.28 μm) indicates that the opacity of the 2007 Tvashtar plume was 2× that of the 1996 and 1999 Pele plume eruptions. While the sulfur dust density estimated for the Tvashtar from the reflected sunlight data could have produced 61% of the observed plume opacity, <10% of the 1999 Pele F255W plume opacity could have resulted from the SO₂ dust detected in the eruption. Accounting for the remaining F255W opacity level of the Pele and Tvasthar plumes based on SO₂ and S₂ gas absorption, the SO₂ and S₂ gas density inferred for each plume is almost equivalent corresponding to ～2–6 × 10¹⁶ cm^?2 and 3–5 × 10¹⁵ cm^?2, respectively, producing SO₂ and S₂ gas resurfacing rates ～0.04–0.2 cm yr^?1 and 0.007–0.01 cm yr^?1; and SO₂ and S₂ gas masses ～1–4 × 10¹⁰ g and ～2–3 × 10⁹ g; for a total dust to gas ratio in the plumes ～10^?1–10^?2. The 2007 Tvashtar plume was detected by HST at ～380 ± 40 km in both reflected sunlight and absorbed jovian light; in 1999, the detected Pele plume altitude was 500 km in absorbed jovian light, but in reflected sunlight the detected height was ～2× lower. Thus, for the 1999 Pele plume, similar to the 1979 Voyager Pele plume observations, the most efficient dust reflections occurred in the region closest to the plume vent. The 0.33–0.42 μm brightness of the 1997 Pillan plume was 10–20× greater than the Pele or Tvashtar plumes, exceeding by a factor of 3 the average brightness levels observed within 200 km of 1979 Loki eruption vent. But, the 0.26 μm brightness of the 1997 Pillan plume in reflected sunlight was significantly lower than would be predicted by the dust scattering model. Presuming that the 0.26 μm brightness of the 1997 Pillan plume was attenuated by the eruption plume’s gas component, then an SO₂ gas density ～3–6 × 10¹⁸ cm^?2 is inferred from the data (for S₂/SO₂ ratios ?4%), comparable to the 0.3–2 × 10¹⁸ cm^?2 SO₂ density detected at Loki in 1979 (Pearl, J.C. et al. [1979]. Nature 280, 755; Lellouch et al., 1992), and producing an SO₂ gas mass ～3–8 × 10¹¹ g and an SO₂ resurfacing rate ～8–23 cm yr^?1. These results confirm the connection between high (?10¹⁷ cm^?2) SO₂ gas content and plumes that scatter strongly at nearly blue wavelengths, and it validates the occurrence of high density SO₂ gas eruptions on Io. Noting that the SO₂ gas content inferred from a spectrum of the 2003 Pillan plume was significantly lower ～2 × 10¹⁶ cm^?2 (Jessup, K.L., Spencer, J., Yelle, R. [2007]. Icarus 192, 24–40); and that the Pillan caldera was flooded with fresh SO₂ frost/slush just prior to the 1997 Pillan plume eruption (Geissler, P., McEwen, A., Phillips, C., Keszthelyi, L., Spencer, J. [2004a]. Icarus 169, 29–64; Phillips, C.B. [2000]. Voyager and Galileo SSI Views of Volcanic Resurfacing on Io and the Search for Geologic Activity at Europa. Ph.D. Thesis, Univ. of Ariz., Tucson); we propose that the density of SO₂ gas released by this volcano is directly linked to the local SO₂ frost abundance at the time of eruption.     

Search for relativistic magnetic monopoles with the Baikal neutrino telescope

We present results of a search for relativistic magnetic monopoles with the Baikal neutrino telescope NT200, using data taken between April 1998 and February 2003. No monopole candidates have been found. We set an upper limit 4.6 × 10⁻¹⁷ cm⁻² s⁻¹ sr⁻¹ for the flux of monopoles with β_m = 1. This is a factor of 20 below the Chudakov–Parker bound which is inferred from the very existence of large-scale galactic magnetic fields.     

The O2 nightglow in the martian atmosphere by SPICAM onboard of Mars-Express

We present observations of the O₂(a¹Δ_g) nightglow at 1.27 μm on Mars using the SPICAM IR spectrometer onboard of the Mars Express orbiter. In contrast to the O₂(a¹Δ_g) dayglow that results from the ozone photodissociation, the O₂(a¹Δ_g) nightglow is a product of the recombination of O atoms formed by CO₂ photolysis on the dayside at altitudes higher than 80 km and transported downward above the winter pole by the Hadley circulation. The first detections of the O₂(a¹Δ_g) nightglow in 2010 indicate that it is about two order of magnitude less intense than the dayglow (Bertaux, J.-L., Gondet, B., Bibring, J.-P., Montmessin, F., Lefèvre, F. [2010]. Bull. Am. Astron. Soc. 42, 1040; Clancy et al. [2010]. Bull. Am. Astron. Soc. 42, 1041). SPICAM IR sounds the martian atmosphere in the near-IR range (1–1.7 μm) with the spectral resolution of 3.5 cm^?1 in nadir, limb and solar occultation modes. In 2010 the vertical profiles of the O₂(a¹Δ_g) nightside emission have been obtained near the South Pole at latitudes of 82–83°S for two sequences of observations: L_s = 111–120° and L_s = 152–165°. The altitude of the emission maximum varied from 45 km on L_s = 111–120° to 38–49 km on L_s = 152–165°. Averaged vertically integrated intensity of the emission at these latitudes has shown an increase from 0.22 to 0.35 MR. Those values of total vertical emission rate are consistent with the OMEGA observations on Mars-Express in 2010. The estimated density of oxygen atoms at altitudes from 50 to 65 km varies from 1.5 × 10¹¹ to 2.5 × 10¹¹ cm^?3. Comparison with the LMD general circulation model with photochemistry (Lefèvre, F., Lebonnois, S., Montmessin, F., Forget, F. [2004]. J. Geophys. Res. 109, E07004; Lefèvre et al. [2008]. Nature 454, 971–975) shows that the model reproduces fairly well the O₂(a¹Δ_g) emission layer observed by SPICAM when the large field of view (>20 km on the limb) of the instrument is taken into account.     

Chandra X-ray observations of two unusual BAL quasars

We report sensitive Chandra X-ray non-detections of two unusual, luminous Iron Low-Ionization Broad Absorption Line Quasars (FeLoBALs). The observations do detect a non-BAL, wide-binary companion quasar to one of the FeLoBAL quasars. We combine X-ray-derived column density lower limits (assuming solar metallicity) with column densities measured from ultraviolet spectra and CLOUDY photoionization simulations to explore whether constant-density slabs at broad-line region densities can match the physical parameters of these two BAL outflows, and find that they cannot. In the “overlapping-trough” object SDSS J0300+0048, we measure the column density of the X-ray absorbing gas to be N_H ? 1.8 × 10²⁴ cm^?2. From the presence of Fe ii UV78 absorption but lack of Fe ii UV195/UV196 absorption, we infer the density in that part of the absorbing region to be n_e ? 10⁶ cm^?3. We do find that a slab of gas at that density might be able to explain this object’s absorption. In the Fe iii-dominant object SDSS J2215–0045, the X-ray absorbing column density of N_H ? 3.4 × 10²⁴ cm^?2 is consistent with the Fe iii-derived N_H ? 2 × 10²² cm^?2 provided the ionization parameter is log U > 1.0 for both the n_e = 10¹¹ cm^?3 and n_e = 10¹² cm^?3 scenarios considered (such densities are required to produce Fe iii absorption without Fe iiabsorption). However, the velocity width of the absorption rules out its being concentrated in a single slab at these densities. Instead, this object’s spectrum can be explained by a low density, high ionization and high temperature disk wind that encounters and ablates higher density, lower ionization Fe iii-emitting clumps.     

Spectroscopic and photometric study of the contact binary BO CVn

We present the results of the study of the contact binary system BO CVn. We have obtained physical parameters of the components based on combined analysis of new, multi-color light curves and spectroscopic mass ratio. This is the first time the latter has been determined for this object. We derived the contact configuration for the system with a very high filling factor of about 88%. We were able to reproduce the observed light curve, namely the flat bottom of the secondary minimum, only if a third light has been added into the list of free parameters. The resulting third light contribution is significant, about 20–24%, while the absolute parameters of components are: M₁ = 1.16, M₂ = 0.39, R₁ = 1.62 and R₂ = 1.00 (in solar units).The O-C diagram shows an upward parabola which, under the conservative mass transfer assumption, would correspond to a mass transfer rate of dM/dt = 6.3 × 10^?8M_⊙/yr, matter being transferred from the less massive component to the more massive one. No cyclic, short-period variations have been found in the O-C diagram (but longer-term variations remain a possibility).     

High resolution investigation of the 7 μm region of the ethane spectrum

Building upon previous studies, we re-investigated the ethane spectrum between 1330 and 1610 cm^?1 by combining unapodized spectra obtained at room temperature with a Bruker Fourier transform spectrometer (FTS) in Brussels and at 131 K with a Bruker FTS in Pasadena. The maximum optical path differences (MOPD) of the two datasets were 450 and 323.7 cm, corresponding to spectral resolutions of 0.0020 and 0.0028 cm^?1, respectively. Of the 15,000 lines observed, over 4592 transitions were assigned to the ν₆ (at 1379 cm^?1), ν₈ (at 1472 cm^?1), ν₄+ν₁₂ (at 1481 cm^?1) and 2ν₄+ν₉ (at 1388 cm^?1) bands, and another 1044 transitions were located for the ν₄+ν₈?ν₄ hot band (at 1472 cm^?1). Our new analysis included an improved implementation of the Hamiltonian calculation needed to interpret the complex spectral structures caused by numerous interactions affecting these four modes of vibration. From these results, we created the first line-by-line database containing the molecular parameters for over 20,000 ¹²C₂H₆ transitions at 7 μm.     

Gamma–hadron separation methods for the VERITAS array of four imaging atmospheric Cherenkov telescopes

Ground-based arrays of imaging atmospheric Cherenkov telescopes have emerged as the most sensitive γ-ray detectors in the energy range of about 100 GeV and above. The strengths of these arrays are a very large effective collection area on the order of 10⁵ m², combined with excellent single photon angular and energy resolutions. The sensitivity of such detectors is limited by statistical fluctuations in the number of Cosmic-ray initiated air showers that resemble γ-ray air showers in many ways. In this paper, we study the performance of simple event reconstruction methods when applied to simulated data of the Very Energetic Radiation Imaging Telescope Array System (VERITAS) experiment. We review methods for reconstructing the arrival direction and the energy of the primary photons, and examine means to improve on their performance. For a software threshold energy of 300 GeV (100 GeV), the methods achieve point source angular and energy resolutions of σ_63% = 0.1° (0.2°) and σ_68% = 15% (22%), respectively. The main emphasis of the paper is the discussion of γ–hadron separation methods for the VERITAS experiment. We find that the information from several methods can be combined based on a likelihood ratio approach and the resulting algorithm achieves a γ–hadron suppression with a quality factor that is substantially higher than that achieved with the standard methods used so far.     

A new absolute magnitude calibration with 2MASS for cataclysmic variables

Using reliable trigonometric measurements, we find that the absolute magnitude of cataclysmic variables depends on the orbital period and de-reddened (J − H)₀ and (H − K _s)₀ colours of 2MASS (Two Micron All Sky Survey) photometric system. The calibration equation covers the ranges 0.032^d < P_orb ⩽ 0.454^d, −0.08 < (J − H)₀ ⩽ 1.54, −0.03 < (H − K_s)₀ ⩽ 0.56 and 2.0 < M_J < 11.7; It is based on trigonometric parallaxes with relative errors of (σ_π/π) ⩽ 0.4. By using the period-luminosity-colours (PLCs) relation, we estimated the distances of cataclysmic variables with orbital periods and 2MASS observations and compared them with distances found from other methods. We suggest that the PLCs relation can be a useful statistical tool to estimate the distances of cataclysmic variables.     

CCD Photometry of the W UMa type star QX Andromeda

We present new B- and V-band photometry of the W UMa-type binary system QX And, which is a member of the open cluster NGC 752. Revised orbital period and new ephemerides were given for the binary system based on the data of times of light minima. The result of a period analysis reveals that the system is undergoing a continuous orbital period increase during the past decades. The rate of period increasing turns out to be about 2.7 × 10^?7 d yr^?1. With the Wilson–Devinney code, a photometric solution is computed. It yields a contact configuration for the system with a filling factor of 0.361. Combining the results from the photometric solution along with that from the radial-velocity observations, we have determined the absolute parameters for the two components of the system. The masses, radii and luminosity of the primary and secondary stars are calculated as 1.43 ± 0.04 M_⊙, 1.45 ± 0.09 R_⊙, 2.87 ± 0.40 L_⊙ and 0.44 ± 0.02 M_⊙, 0.87 ± 0.05 R_⊙, 0.99 ± 0.13 L_⊙, respectively. The evolutionary status and physical nature of the contact binary system were discussed compared with the theoretical models.     

Spatial correlation of OH Meinel and O2 infrared atmospheric nightglow emissions observed with VIRTIS-M on board Venus Express

We present the two-dimensional distribution of the O₂ a¹Δ–X³Σ (0–0) band at 1.27 μm and the OH Δv = 1 Meinel airglow measured simultaneously with the Visible and Infrared Thermal Imaging Spectrometer (VIRTIS) on board Venus Express. We show that the two emissions present very similar spatial structures. A cross-correlation analysis indicates that the highest level of correlation is reached with only very small relative shifts of the pairs of images. In spite of the strong spatial correlation between the morphology of the bright spots in the two emissions, we also show that their relative intensity is not constant, in agreement with earlier statistical studies of their limb profiles. We conclude that the two emissions have a common precursor that controls the production of both excited species. We argue that atomic oxygen, which produces O₂ (¹Δ) molecules by three-body recombination and is the precursor of ozone formation, also governs to a large extent the OH airglow morphology through the H + O₃ → OH^* + O₂ reaction.     

Spatial variability,composition and thickness of the seasonal north polar cap of Mars in mid-spring

The planetary fourier spectrometer (PFS) for the Mars express mission (MEX) is an infrared spectrometer operating in the wavelength range from 1.2 to 45 μm by means of two spectral channels, called SWC (short wavelength channel) and LWC (long wavelength channel), covering, respectively, 1.2–5.5 and 5.5–45 μm.The middle-spring Martian north polar cap (Ls∼40°) has been observed by PFS/MEX in illuminated conditions during orbit 452. The SWC spectra are here used to study the cap composition in terms of CO₂ ice, H₂O ice and dust content. Significant spectral variation is noted in the cap interior, and regions of varying CO₂ ice grain sizes, water frost abundance, CO₂ ice cover and dust contamination can be distinguished. In addition, we correlate the infrared spectra with an image acquired during the same orbit by the OMEGA imaging spectrometer and with the altimetry from MOLA data. Many of the spectra variations correlate with heterogeneities noted in the image, although significant spectral variations are not discernible in the visible. The data have been divided into five regions with different latitude ranges and strong similarities in the spectra, and then averaged. Bi-directional reflectance models have been run with the appropriate lighting geometry and used to fit the observed data, allowing for CO₂ ice and H₂O ice grain sizes, dust and H₂O ice contaminations in the form of intimate granular mixtures and spatial mixtures.A wide annulus of dusty water ice surrounds the recessing CO₂ seasonal cap. The inner cap exhibits a layered structure with a thin CO₂ layer with varying concentrations of dark dust, on top of an H₂O ice underneath ground. In the best-fits, the ices beneath the top layer have been considered as spatial mixtures. The results are still very good everywhere in the spectral range, except where the CO₂ ice absorption coefficients are such that even a thin layer is enough to totally absorb the incoming radiation (i.e. the band is saturated). This only happens around 3800 cm⁻¹, inside the strong 2.7-μm CO₂ ice absorption band. The effect of finite snow depth has been investigated through a layered albedo model. The thickness of the CO₂ ice deposits increases with latitude, ranging from 0.5–1 g cm⁻² within region II to 60–80 g cm⁻² within the highest-latitude (up to 84°N) region V.Region I is at the cap edge and extends from 65°N to 72°N latitude. No CO₂ ice is present in this region, which consists of relatively large grains of water ice (20 μm), highly contaminated by dust (0.15 wt%). The adjacent region II is a narrow region [76–79°N] right at the edge of the north residual polar cap. This region is very distinct in the OMEGA image, where it appears to surround the whole residual cap. The CO₂ ice features are barely visible in these spectra, except for the strong saturated 2.7 μm band. It basically consists of a thin layer of 5-mm CO₂ ice on top of an H₂O ice layer with the same composition as region I. A third interesting region III is found all along the shoulder of the residual cap [79–81°N]. It extends over 1.5 km in altitude and over only 2° of latitude and consists of CO₂ ice with a large dust content. It is an admixture of CO₂ ice (3–4 mm), with several tens of ppm by mass of water ice and more than 2 ppt by mass of dust. The surface temperatures have been retrieved from the LWC spectra for each observation. We found an increase in the surface temperature in this region, indicating a spatial mixture of cold CO₂ ice and warmer dust/H₂O ice. Region IV is close to the top of the residual cap [81–84°N]; it is much brighter than region III, with a dust content 10 times lower than the latter. The CO₂ grain size is 3 mm and strong CO₂ ice features are present in the data, indicating a thicker CO₂ ice layer than in region II (1–2 g cm⁻²). The final region V is right at the top of the residual cap (⩾84°N). It is “pure” CO₂ ice (no dust) of 5 mm grain sizes, with 30 ppm by weight of water ice. The CO₂ ice features are very pronounced and the 2.7 μm band is saturated. The optical thickness is close to the semi-infinite limit (30–40 g cm⁻²). Assuming a snowpack density of 0.5 g cm⁻³, we get a minimum thickness of 1–2 cm for the top-layer of regions II and III, 4–10 cm for region IV, and ⩾60–80 cm thickness for region V. These values are in close agreement with several recent results for the south seasonal polar cap.These results should provide new, useful constraints in models of the Martian climate system and volatile cycles.     

The role of sputtering and radiolysis in the generation of Europa exosphere

The exosphere of an atmosphereless icy moon is the result of different surface release processes and subsequent modification of the released particles. At Europa icy moon, water molecules are directly released, but photolysis and radiolysis due to solar UV and Jupiter’s magnetospheric plasma, respectively, can result in OH, H, O and (possibly) H₂ production. These molecules can recombine to reform water and/or new chemical species. As a consequence, Europa’s neutral environment becomes a mixture of different molecules, among which, H₂O dominates in the highest altitudes and O₂, formed mainly by radiolysis of ice and subsequent release of the produced molecules, prevails at lower altitudes. In this work, starting from a previously developed Monte Carlo model for the generation of Europa’s exosphere, where the only considered species was water, we make a first attempt to simulate also the H₂ and O₂ components of the neutral environment around Europa, already observed by the Hubble Space Telescope and the Ultraviolet Imaging Spectrograph on board Cassini, during its flyby of Jupiter. Considering a specific configuration where the leading hemisphere coincides with the sunlit hemisphere, we estimate along the Europa–Sun line an O₂ column density of about 1.5 × 10¹⁹ m^?2 at the dayside and 3 × 10¹⁸ m^?2 at the nightside. In this work we also improve our previous estimation of the sputtered H₂O exosphere of this moon, taking into consideration the trailing–leading asymmetry in the magnetospheric ion bombardment and the energy and temperature dependences of the process yields. We find that a density of 1.5 × 10¹² H₂O/m³ is expected at altitudes ～0.1R_E above the surface of the trailing hemisphere. Additionally, we calculate the escape of H₂O, O₂ and H₂. The total number of neutral atoms in Europa’s neutral torus, is estimated to be in the range 7.8 × 10³²–3.3 × 10³³.     

Absolute properties of the overcontact binary HH Boo

We obtained multi-colour light curves of the overcontact binary system HH Boo and analysed the orbital period variation of the system. Our analysis tentatively indicates either mass transfer from the secondary to the primary or mass loss from the system at a rate of -5.04 × 10⁻⁷ M_⊙ per year. Through a combined analysis of the published radial velocity curve and light curves, we determined an inclination (i) of 69°.71 ± 0°.16 and a semi-major axis (a) of 2.246 ± 0.064 R_⊙ for HH Boo. The masses of the primary and secondary components were found to be 0.92 ± 0.08 M_⊙ and 0.58 ± 0.06 M_⊙, respectively. The radius determined for the primary was 0.98 ± 0.03 R_⊙, while that determined for the secondary was 0.80 ± 0.02 R_⊙. We demonstrated that HH Boo is most likely a member of the A-type subclass of W UMa binaries.