Fabrication of anodized superhydrophobic 5083 aluminum alloy surface for marine anti-corrosion and anti-biofouling

Marine corrosion and biofouling seriously affect the service life of marine structural materials,resulting in performance failure,enormous economic loss,and even catastrophic safety accidents.It is worthwhile and desirable to develop high-efficiency strategy for anti-corrosion and anti-biofouling.In this paper,superhydrophobic 5083 aluminum alloy(AA5083) surface with micro-nano hierarchical morphology was fabricated through anodization followed by 1 H,1 H,2 H,2 H-perfluorooctyltriethoxysilane(POTS)modification.The surface morphologies,roughness,and chemical compositions were revealed by scanning electron microscopy,atomic force microscopy,and X-ray diffraction.The self-cleaning ability,corrosion resistance and algae adhesion suppression ability of the fabricated surfaces were investigated,indicating an excellent water-proofing,anti-corrosion and anti-biofouling performance.We believe the superhydrophobic creation of metallic materials is expected to have potential applications in marine corrosion and antibiofouling fields.     

Electrochemical corrosion behavior of hot dip coating in artificial seawater

INTR0DUCnONAlloycoatingscandetivelyproteCtsteelagainstcormsioninseri0uscormsionenvir-orunent,suchasthedrinesplashandtidalzones-TwoInainhodiptincaldrinumalloycOaingswidelyusedcommroiallyareGalfancoaing(contalningZn-5wt%kl-us)devel-oPedbytheIntemaionaltalZincReenhheZaionandhocoating(c0n-talningZn-55Wt%Al-1.6Wt%Si)develoPedbytheBethlehemSteelCorpOration-Anewrinc-basedalloycOaingdevel0PedbyNortheaStemUniversityisdiscussedinthesPaperbyelecthehendcalmethod.FromSun(l996),welmOWthecorms…     

Corrosion Behavior of Anodic Oxidized TiO_2 Film in Seawater

TiO2 films were formed on metallic titanium substrates by the anodic oxidation method in H2SO4 solution under the 80V D.C..Phase component and microstructure were characterized by X-ray diffraction (XRD) and scanning electron microscopy (SEM).Water contact angles on titanium oxide film surface were measured under both dark and sunlight illumination conditions.Corrosion tests were carried out in seawater under different illumination conditions by electrochemistry impedance spectrum (EIS) and polarization curves.The result showed that the TiO2 film prepared by the anodic oxidation method was anatase with a uniform structure and without obvious pores or cracks on its surface.The average water contact angle of the film was 116.4? in dark, in contrast to an angle of 42.7? under the UV illumination for 2 hours, which demonstrates good hydrophobic property.The anti-corrosion behavior of the TiO2 film was declining with the extended immersion time.Under dark conditions, however, the hydrophobic TiO2 film retarded the water infiltrating into the substrate.The impedance changed slowly and the corrosion current density was 2 orders of magnitude lower than that with the film illuminated by sunlight.All of those mentioned above indicate that the TiO2 film possesses much better performance under dark condition, and it can be applied as an engineering material under dark seawater environment.     

Alloy elements' effect on steel corrosion in marine environment

INTRODUCTIONBesidesprotectivecoatingandcathodicprotectionmethodsagainstcorrosionoflowalloysteelconstructuresinmarineenvironment,itisalsoimportanttoimprovethecorrosionresistanceofthelowalloysteelitself.Therearefewreportsontherelationshipofalloyelementandthecorrosionre sistanceofsteel .Larrabee (1 958)’s 5-9yearsseaexperimentusinglong scalesteelshowedthatthecorrosionresistanceof 0 .5%Ni-0 .5%Cu -0 .1 %Psteelwasthehighestinthesplashzone .HouandZhang (1 980 )consideredthataproperrelationshi…     

CORROSION RESISTANCE OF INTERFERENCE FILM ON STAINLESS STEEL

IwrRODUcrlONStainlessstalhasbeenusedwidelyasbuildingrnateria1,especiallyasdecoratingrnate-rialinbuildings.Ordinarystainlesssteehasonlyonemonot0noussilverywhitCcolourwhichsomeimesdoesnotrnatchwithitSsurmundingenvironment.lnordert0improveitSdereratingperfonnaneeandexpanditsuse,muchresearchhasbeenconductedsincethe4O'st0trytoformabright,uniform,highcorrosi0nandwearresistantco1ourfilmonastainlesssteesurface.Duringtheeariystage,anirnmersionedhodwasused,i.e.inimrs-ingthestainlesssteelinahots0luti…     

Corrosion behavior of anodic oxidized TiO<Subscript>2</Subscript> film in seawater

TiO₂ films were formed on metallic titanium substrates by the anodic oxidation method in H₂SO₄ solution under the 80V D.C.. Phase component and microstructure were characterized by X-ray diffraction (XRD) and scanning electron microscopy (SEM). Water contact angles on titanium oxide film surface were measured under both dark and sunlight illumination conditions. Corrosion tests were carried out in seawater under different illumination conditions by electrochemistry impedance spectrum (EIS) and polarization curves. The result showed that the TiO₂ film prepared by the anodic oxidation method was anatase with a uniform structure and without obvious pores or cracks on its surface. The average water contact angle of the film was 116.4° in dark, in contrast to an angle of 42.7° under the UV illumination for 2 hours, which demonstrates good hydrophobic property. The anti-corrosion behavior of the TiO₂ film was declining with the extended immersion time. Under dark conditions, however, the hydrophobic TiO₂ film retarded the water infiltrating into the substrate. The impedance changed slowly and the corrosion current density was 2 orders of magnitude lower than that with the film illuminated by sunlight. All of those mentioned above indicate that the TiO₂ film possesses much better performance under dark condition, and it can be applied as an engineering material under dark seawater environment.     

Evaluation and classification of seawater corrosiveness by environmental factors

According to the data of main environmental factors and the depth of localized corrosion of carbon steel and low alloy steels in China seas, combined with the result of grey interrelation analysis, double-factor method was proposed to evaluate and classify seawater corrosiveness. According to the temperature of seawater and the biologically adhesive area on steels, the corrosiveness of seawater from low to high level is classified into five levels （C l-C5）, which was identified by the data of corrosion depth of carbon steel immersed in water for one year.     

Corrosion performance of zinc coated steel in seawater environment

Considering the continuous exploitation of marine resources,it is very important to study the anticorrosion performance and durability of zinc coated streel(ZCS) because its increasing use as reinforcements in seawater.Tafel polarization curves and linear polarization curves combined with electrochemical impedance spectroscopy(EIS) were employed to evaluate the corrosion performance of ZCS at Qingdao test station during long-term immersion in seawater.The results indicated that the corrosion rate of the ZCS increased obviously with immersion time in seawater.The corrosion products that formed on the zinc coated steel were loose and porous,and were mainly composed of Zn_5(OH)_8Cl_2,Zns(OH)_6(CO_3)_2,and ZnO.Pitting corrosion occurred on the steel surface in neutral seawater,and the rate of ZCS corrosion decreased with increasing pH.     

三元复合驱采油污水阻垢缓蚀剂电化学分析

研制适用于三元复合驱采油污水工况条件下的MPM固体缓蚀阻垢剂,分析三元复合驱采油污水中MPM的电化学特性.结果表明:随着温度增加,20#钢在采油污水的腐蚀速率呈增加趋势,极化曲线显示钝化区表面材料在表面高温下处于钝化状态,产生的钝化膜能够降低腐蚀速度.在阻垢缓蚀剂质量浓度相同的情况下,不同温度的电化学阻抗谱在高频区出现容抗弧,显示优良的缓蚀性能.不同质量浓度MPM极化曲线表明,缓蚀率随MPM质量浓度的增加而增大,MPM极值质量浓度为80mg/L.污水体系中的Ca2+、Cl-对缓蚀率产生影响.MPM适用于高质量浓度Ca2+的三元复合驱采油污水处理.     

THE CORROSIVE EFFECT OF BARNACLES ON LOW ALLOY STEELS

The effect of barnacles on corrosion of low alloy (16Mn) steel was studied by immersing steel panels in seawater at Zhonggang.Qingdao, for 41 months. It was found that the secondary attachment on this kind of steel by barnacles had less effect on its corrosion while the primary attachment had a greater effect; that different seasons have different effects on the form and extent of local corrosion in this steel, and that primarily attached barnacles cause more serious local corrosion in high breeding seasons when there are more attachments.     

Effect of Carbonation and Drying-Wetting Cycles on Chloride Diffusion Behavior of Coral Aggregate Seawater Concrete

Based on seawater immersion,drying-wetting cycles,carbonation and drying-wetting cycles for coral aggregate sea-water concrete(CASC)with different strength grades,the effect of carbonation and drying-wetting cycles on chloride diffusion be-havior of CASC is studied.The results show that the free surface chloride concentration(Cs),free chloride diffusion coefficient(Df)and time-dependent index(m)of CASC in the drying-wetting cycles is obviously higher than that in seawater immersion.The Df and m of CASC of carbonation and drying-wetting cycles is higher than that in the drying-wetting cycles.Carbonation increases the Df and m of CASC,which is against CASC to resist chloride corrosion.The corrosion possibility of CASC structures in different ex-posed areas is as follows:splash zone(carbonation and drying-wetting cycles)>tidal zone(drying-wetting cycles)>underwater zone(seawater immersion).Besides,the chloride diffusion rate of C65-CASC is 17.8%-63.4%higher than that of C65-ordinary aggre-gate concrete(OAC)in seawater immersion(underwater zone).Therefore,anti-corrosion measures should be adopted to improve the service life of CASC structure in the oceanic environment.     

FLUXES OF SEAWATER AND SOME DISSOLVED CHEMICALS IN THE BASHI STRAIT

An Acoustic Doppler Current Profiler (ADCP) was used in Nov. 1990 measure the seawaterfluxes in a southeast-northwest cross-section in the Bashi Strait to a depth of 400 m. Measuredconcentrations of dissolved oxygen (DO), phosphate (PO_4), nitrate (NO_3), silicate (SiO_2), total alkalinity(TA) and calculated total CO_2, (TCO_2) and the current speed were used to estimate the flux densities(concentration times current speed) of seawater and chemicals.The fluxes of nutrients were near zero near surface and increased with depth. For oxygen andcarbonates, the distributions of flux had structures similar to that of the curmt speed field.     

米曲霉产中性蛋白酶的适宜条件

研究了米曲霉产蛋白酶的分布,优化了米曲霉产中性蛋白酶的适宜培养条件以及培养基的最优组成。研究发现米曲霉产中性蛋白酶的能力为最强。米曲霉产中性蛋白酶的适宜培养条件为:m(麸皮)∶m(豆粕粉)=4∶1,水的质量分数为60%,培养基中各无机盐质量分数为:KNO30.2%,MgSO40.05%,Na2HPO40.13%,pH值为6.0,接种量为每10 g培养基接种1.0×108个孢子,最佳培养温度为30℃,最佳培养时间为48 h。在此培养条件下,最高酶活力达3 999.2 U.g-1。     

Effect of Ca(OH)2, NaCl,and Na2SO4 on the corrosion and electrochemical behavior of rebar

The corrosion of rebar in reinforced concrete in marine environments causes significant damage to structures built in ocean environments. Studies on the process and mechanism of corrosion of rebar in the presence of multiple ions may help to control damage and predict the service life of reinforced concrete structures in such environments. The effect of interactions between sulfate and chloride ions and calcium hydroxide on the electrochemical behavior of rebar are also important for evaluation of structure durability. In this work, electrochemical impedance spectroscopy(EIS) plots of rebar in Ca(OH)_2 solution and cement grout, including NaCl and Na_2SO_4 as aggressive salts, were measured for different immersion times. The results show that corrosion of rebar was controlled by the rate of charge transfer as the rebar was exposed to chloride solution. In the presence of high concentrations of sulfate ions in the electrolyte, generation and dissolution of the passive film proceeded simultaneously and corrosion was mainly controlled by the diffusion rate. When Na_2SO_4 and NaCl were added to Ca(OH)_2 solution, the instantaneous corrosion rate decreased by a factor of 10 to 20 as a result of the higher p H of the corroding solution.     

INFLUENCE OF ACTIVE MARINE ORGANIC MATTER ON ELECTROCHEMICAL CORROSION Ⅰ.STUDY ON BROWN ALGAE POLYPHENOLS' ACTION ON CARBON STEEL

INTRODUCTIONBrownalgaepolyphenol (BAP)isadistinctivenaturalproduct,anactiveorganicmatterre leasedfromnormalgrowingbrownalgaeintoseawater.TheBAPoutputfromthelivingbrownalgaeis 1g (m2 ·d) (Craigieetal.,1 964 ) .About3 7%ofdissolvedorganicmatter(DOM)inseawateralongshoreisthesecretionfromseaweedcells,andcanreach 70 %oftotalDOMinseawaterifor ganicmatterreleasedbydeadalgaeisincluded (Raganetal.,1 979) .BAP (mainlycomprisingtheyellowmatter)inseawateralongshore ,canreach 2 .5mg L (Rashida…     

The drift velocity of oil film on the sea

To make surface seawater flow, the shear stress of the wind blowing on the sea must overcome the work of cohesion of seawaterW _c. Oil film on the sea will drift along the wind direction so long as the shear stress of the wind overcomes the work of adhesion between the water and the oilW _a or the work of cohesion of oil W_t,o. Experiments bear out the theory that surface tension of seawater is more than twice that of oils generally, so that the wind influenced drift velocity of the oil film is over two times that of the wind-driven surface current. The wind factor for surface current in Jiaozhou Bay is 0.025, while those for the drift velocities of O-diesel oil film and the used light crude oil film are 0.070 and 0.052 respectively. Generally the primary factors influencing the movement velocity of oil film on the sea are current, wind, and the physicochemical properties of the oil. The drift velocity of oil film is determined from analysis of the work of adhesion between seawater and oil. Experiments and actual observations agree with the theoretical analysis. Contribution No. 1831 from the Institute of Oceanology, Academia Sinica     

STUDY ON THE ANALYSIS AND DISTRIBUTION OF DIMETHYL SULFIDE IN THE EAST CHINA SEA

A method is described for determining dimethylI sulfide (DMS) in seawater. DMS was first extractedfrom the seawater using organic reagent, then reverse-extracted by 5% HgCl2. In the laboratory DMS wasreleased by concentrated HCI and finally measured by GC-FPD. The limit of detection me O.05 ng ofS. Measurements of DMS along surface transects and on wtital profibe across the EaSt China Sca (Ers)continental sheif showed tha itS conodIations of S in the surface seawater ranged from 64-180 ng/L andthat itS vertical djstribuion was divided into 3 trpes. Model talculations of a stagnant film show a DMSflux of 10.6 umol/m_2d the air-sea inteIha.     

Nutrients in seawater and interstitial water of the sediments in the Huanghe River estuarine area (November)

The investigation shows that the concentrations of nutrients are high in estuarine and coastal waters and low in offshore waters. The concentration of nitrate in estuaries is controlled through a physical mixing process and is also affected by biotic activity. The annual transport of total inorganic nitrogen and dissolved phosphate-phosphorus from the Huanghe River water to the sea is about 8.45 ×10⁴ and 1.45×10³ tons respectively. The distributions of inorganic nitrogen and silicate in interstitial water of surface sediments are similar to those in surface and bottom seawater. Their contents in interstitial water are 227–552 μmol/l (average375) for ammonia, 0.31–9.0 μmol/l (average 1.6) for nitrite, 0–41 μmol/l (average6.0) for nitrate, and 41–139 μmol/l (average 77) for silicate. The average concentrations of phosphate in the surveyed area are 0.64 μmol/l for seawater and 1.2 μmol/l for interstitial water. A cycle of phosphate in the estuary is also suggested in this paper. Contribution No. 1434 from Institute of Oceanology, Academia Sinica.     

Influence of active marine organic matter on electrochemical corrosion

Chemical means were used to extract polyphenols from healthy brown algae collected in littoral seawater. Experiments on corrosion of A₃ steel, the time-potential curve, and polarization curve in polyphenols seawater showed stronger cathodic polarization compared with that in common seawater. This indicates that brown algae polyphenols might feasibly be used as corrosion inhibitor in seawater. Contribution No. 3763 from the Institute of Oceanology, Chinese Academy of Sciences. Project 59471054 supported by NSFC and National “Nineth Five Year” Project 96-916-04-01.     

The distribution of green algal micro-propagules and macroalgae at the early stage of green tide in the coastal area of South Jiangsu Province in 2014

An integrated investigation was carried out during late April to late May of 2014 in the coastal area of South Jiangsu Province to understand the early development of green tide in the Yellow Sea and discover the temporal and spatial distribution of green algal micro-propagules and macroalgae at the early stage of green tide. The results showed that green algal micro-propagules distributed in all stations from late April to late May, and micro-propagules of high density( 300 ind. L~(-1)) concentrated in the adjacent Porphyra aquaculture area. Floating macroalgae were initially observed in the northern survey areas, and increased gradually. The dominant species was U. prolifera in the floating macroalgae, ranging between 90% and 100%. The seawater surface temperature and salinity in the above mentioned time period were suitable for the growth of macroalgae. This work can help government to strengthen management to reduce the blooms of macroalgae in the coastal area of South Jiangsu Province and also facilitate the decision-making for managers at the early stage of green tide.