Bed morphological changes around a finite patch of vegetation

For the appropriate management and restoration of rivers, isolated vegetation is often a practical means for improving stream habitat and ecology. The effect of a finite vegetation patch on flow and bed morphology in an open channel was investigated using laboratory experiments. The patch containing emergent and submerged vegetation was modeled using circular cylinders and located mid‐channel along a side wall. Several configurations of the patch and submergence ratio (i.e. water depth to the height of vegetation), and two flow conditions (i.e. below and above the sediment motion threshold) were considered. For flows below the sediment motion threshold, erosion occurred primarily on the opposite side of the patch and near the leading edge of the patch. The degree of scouring depth observed in both these regions was affected by the submergence ratio and it increased with the non‐dimensional flow blockage (i.e. the product of the patch density and width). In contrast, for flows above the sediment motion threshold, sediment accumulated within and around the patch due to a reduction in bed shear stress, which was strongly influenced by the flow blockage and the obstruction ratio (i.e. the ratio of patch width to channel width). The eroded area observed within the patch was consistent with the interior adjustment region where the deceleration and diversion of flow occurred through the patch. As the flow blockage increased or as the obstruction ratio decreased, the deposition rate within and behind the patch decreased. Furthermore, the deposition rate increased with an increase in the ratio of flow rate through the patch to total flow rate regardless of the submergence ratio. Copyright © 2014 John Wiley & Sons, Ltd.     

How sediment composition and flow rate influence downstream channel morphodynamics upon dam removal

The process of dam removal establishes the channel morphology that is later adjusted by high-flow events. Generalities about process responses have been hypothesized, but broad applicability and details remain a research need. We completed laboratory experiments focused on understanding how processes occurring immediately after a sediment release upon dam removal or failure affect the downstream channel bed. Flume experiments tested three sediment mixtures at high and low flow rates. We measured changes in impounded sediment volume, downstream bed surface, and rates of deposition and erosion as the downstream bed adjusted. Results quantified the process responses and connected changes in downstream channel morphology to sediment composition, temporal variability in impounded sediment erosion, and spatial and temporal rates of bedload transport. Within gravel and sand sediments, the process response depended on sediment mobility. Dam removals at low flows created partial mobility with sands transporting as ripples over the gravel bed. In total, 37% of the reservoir eroded, and half the eroded sediment remained in the downstream reach. High flows generated full bed mobility, eroding sands and gravels into and through the downstream reach as 38% of the reservoir eroded. Although some sediment deposited, there was net erosion from the reach as a new, narrower channel eroded through the deposit. When silt was part of the sediment, the process response depended on how the flow rate influenced reservoir erosion rates. At low flows, reservoir erosion rates were initially low and the sediment partially exposed. The reduced sediment supply led to downstream bed erosion. Once reservoir erosion rates increased, sediment deposited downstream and a new channel eroded into the deposits. At high flows, eroded sediment temporarily deposited evenly over the downstream channel before eroding both the deposits and channel bed. At low flows, reservoir erosion was 17–18%, while at the high flow it was 31–41%.     

Influence of diversion angle on water and sediment flow into diversion channel

Accumulation of the sediment in the stream of the diversion channels adversely affects its operational systems. Diversion channels are often constructed perpendicular to the main river. In this study, the water flow and sediment transport in the diversion channel with different angles were investigated in an attempt to maximize water discharge and minimize sediment discharge. A physical model with movable bed was used to simulate water and sediment flow with five diversion angles (θ) between (30°–90°). Moreover, three bed width ratios (B_r) (the relation between diversion to main channel bed width) between 30% and 50% and five total discharges between (7.25 L/s to 12.25 L/s) were considered for each case of (θ). The results showed, up to 10%, increasing in proportion discharge ratios for 30 and 45 diversion angles compared with 90° diversion angle. The results also showed that the lowest diversion sediment concentration was provided by the (θ) of 30°. Across all scenarios, the average proportion concentration reduction was 64%, compared with 90° diversion angle. Closer observation of the diversion system mechanism confirmed that decreased (θ) result in decreased sediment concentrations in the diversion channels. In conclusion, the diversion channel water and sediment discharge could be effectively managed by changing the (θ) to 30° or 45° instead of 90°.     

Estimating bed material fluxes upstream and downstream of a controlled large bifurcation - the Mississippi-Atchafalaya River diversion

Bed material transport at river bifurcations is crucial for channel stability and downstream geomorphic dynamics. However, measurements of bed material transport at bifurcations of large alluvial rivers are difficult to make, and standard estimates based on the assumption of proportional partitioning of flow and bedload transport at bifurcations may be erroneous. In this study, we employed a combined approach based on observed topographic change (erosion/deposition) and bed material transport predicted from a one-dimensional model to investigate bed material fluxes near the engineering-controlled Mississippi-Atchafalaya River diversion, which is of great importance to sediment distribution and delivery to Louisiana's coast. Yang's (1973) sediment transport equation was utilized to estimate daily bed material loads upstream, downstream, and through the diversion during 2004–2013. Bathymetric changes in these channels were assessed with single beam data collected in 2004 and 2013. Results show that over the study period, 24% of the Mississippi River flow was diverted into the Atchafalaya River, while the rest remained in the mainstem Mississippi. Upstream of the diversion, the bed material yield was predicted to be 201 million metric tons (MT), of which approximately 35 MT (i.e., 17%) passed through the bifurcation channel to the Atchafalaya River. The findings from this study reveal that in the mainstem Mississippi, the percentage of bed material diversion (83%) is larger than the percentage of flow diversion (76%); Conversely, the diversion channel receives a disproportionate amount of flow (24%) relative to bed material supply (17%). Consequently, severe bed scouring occurred in the controlled Outflow Channel to the Atchafalaya River, while riverbed aggradation progressed in the mainstem Mississippi downstream of the diversion structures, implying reduced flow capacity and potential risk of a high backwater during megafloods. The study demonstrates that Yang's sediment transport equation provides plausible results of bed material fluxes for a highly complicated large river diversion, and that integration of the sediment transport equation with observed morphological changes in riverbed is a valuable approach to investigate sediment dynamics at controlled river bifurcations.     

Reduction of bend scour with an air-bubble screen-morphology and flow patterns

The interplay between streamwise flow,curvature-induced secondary flow,sediment transport and bed morphology leads to the formation of a typical bar-pool bed morphology in open-channel bends.The associated scour at the outer bank and deposition at the inner bank may endanger the outer bank’s stability or reduce the navigable width of the channel.Previous preliminary laboratory experiments in a sharply curved flume with a fixed horizontal bed have shown that a bubble screen located near the outer bank can generate an additional secondary flow located between the outer bank and the curvature-induced secondary flow and with a sense of rotation opposite to the latter.This bubble-induced secondary flow redistributes velocities and bed shear stresses.The reported study investigates the implications of a bubble screen on the flow and the morphology in configurations with mobile bed.Velocity measurements show that the bubble-induced secondary flow shifts the curvature-induced secondary flow in inwards direction and reduces its strength.The bubble screen considerably reduces morphological gradients.Maximum bend scour is reduced by about 50%and occurs further away from the outer bank where it does not endanger the bank stability anymore.The location of maximum scour coincides with the junction of the curvature-induced and bubble-induced secondary flows.At this same location,the maximum streamwise velocities and maximum vertical velocities impinging on the bed also occur,which indicates their importance with respect to the formation of bend scour.The bubble screen also substantially reduced deposition at the inner bank.These preliminary experiments show the potential of a bubble screen to influence and modify the bed morphology.     

Observations of bedload movement,bar development and sediment supply in the braided Ohau river

Relative bedload transport rate and hydraulic parameters were measured on two occasions in a reach of the braided, gravel-bedded Ohau River. Each reach contained a deep, fast-flowing chute leading to an area of diverging, shallow flow which contained a middle bar. The measurements are self-consistent, and indicate that, where flow is concentrated in a deep chute, shear stress is high, but where flow diverges, depth, slope and shear stress decrease. In the first survey, the bed was scoured in the chute and sediment transport rates were high, but where flow diverged sediment transport rate decreased. It appears that deposition leads to bar growth, bar growth in turn reduces slope and depth, deposition is encouraged, and the bar continues to grow vertically, laterally and upstream. In the second survey no sediment transport was observed, despite hydraulic conditions very similar to the first survey. The absence of sediment transport is attributed to the cessation of sediment supply to the river channel.     

Numerical calculation for bed variation in compound-meandering channel using depth integrated model without assumption of shallow water flow

In a compound meandering channel, patterns of flow structures and bed variations change with increasing water depth owing to complex momentum exchange between high-velocity flow in a main channel and low-velocity flows in flood plains. We have developed a new quasi-three-dimensional model without the shallow water assumption, i.e., hydrostatic pressure distribution; our method is known as the general bottom velocity computation (BVC) method. In this method, a set of depth-integrated equations, including depth-integrated momentum and vorticity equations, are prepared for evaluating bottom velocity and vertical velocity distributions. The objective of this study is to develop a bed variation calculation method for both single and compound meandering channels by using the BVC method coupled with a sediment transport model. This paper shows that the BVC method can reproduce the pattern change of bed variation in a compound meandering channel flow with increasing relative depth. The variation in sediment transport rate due to overbank flow is explained by experimental and computational results.     

SCOUR RATE FORMULA

I.INTRODUCTIONhiverchannelsaresubjecttocontinuouschangeingeometryduetoillteraCtionbetWeentheflowanderodibleboundaries.Ofconcerntothedesignersofoilpipelinesacrossariver,bridgesandhydraulicworksistheproblemofscourwhichcanunderminetheStructures.Scouratsiteofbridgesandhydraulicworksoccursduetoconstrictedflowandexistenceofbridgepiers.SuchatabOfscouroccursonlyinashortsection,usuallyillthesameorderofthelengthofthehydraulicworksorbridges.Therefore,thispatternofscouriscalledlocalscour.Man}rresea…     

Morphodynamic assessment of side channel systems using a simple one‐dimensional bifurcation model and a comparison with aerial images

Side channel construction is a common intervention applied to increase a river's conveyance capacity and to increase its ecological value. Past modelling efforts suggest two mechanisms affecting the morphodynamic change of a side channel: (1) a difference in channel slope between the side channel and the main channel and (2) bend flow just upstream of the bifurcation. The objective of this paper was to assess the conditions under which side channels generally aggrade or degrade and to assess the characteristic timescales of the associated morphological change. We use a one‐dimensional bifurcation model to predict the development of side channel systems and the characteristic timescale for a wide range of conditions. We then compare these results to multitemporal aerial images of four side channel systems. We consider the following mechanisms at the bifurcation to be important for side channel development: sediment diversion due to the bifurcation angle, sediment diversion due to the transverse bed slope, partitioning of suspended load, mixed sediment processes such as sorting at the bifurcation, bank erosion, deposition due to vegetation, and floodplain sedimentation. There are limitations to using a one‐dimensional numerical model as it can only account for these mechanisms in a parametrized manner, but the model reproduces general behaviour of the natural side channels until floodplain‐forming processes become important. The main result is a set of stability diagrams with key model parameters that can be used to assess the development of a side channel system and the associated timescale, which will aid in the future design and maintenance of side channel systems. © 2017 The Authors. Earth Surface Processes and Landforms published by John Wiley & Sons Ltd.     

Multigene genetic programming for sediment transport modeling in sewers for conditions of non-deposition with a bed deposit

It is known that construction of large sewers based on consideration of flow with non-deposition without a bed deposit is not economical. Sewer design based on consideration of flow with non-deposition with a bed deposit reduces channel bed slope and construction cost in which the presence of a small depth of sediment deposition on the bed increases the sediment transport capacity of the flow. This paper suggests a new Pareto-optimal model developed by the multigene genetic programming (MGGP) technique to estimate particle Froude number (Fr_p) in large sewers with conditions of sediment deposition on the bed. To this end, four data sets including wide ranges of sediment size and concentration, deposit thickness, and pipe size are used. On the basis of different statistical performance indices, the efficiency of the proposed Pareto-optimal MGGP model is compared to those of the best MGGP model developed in the current study as well as the conventional regression models available in the literature. The results indicate the higher efficiency of the MGGP-based models for Fr_p estimation in the case of no additional deposition onto a bed with a sediment deposit. Inasmuch as the Pareto-optimal MGGP model utilizes a lower number of input parameters to yield comparatively higher performance than the conventional regression models, it can be used as a parsimonious model for self-cleansing design of large sewers in practice.     

1999-2015年汛后小浪底水库典型支流口门淤积发展影响分析

支流作为水库综合效益发挥的重要组成部分,其河口泥沙大幅淤积会影响水库综合效益的发挥.选取多沙河流水库黄河小浪底库区畛水、石井两支流作为典型实例,在对1999-2015年汛后水库的来水来沙、水库调度、库区干支流淤积量与形态分析基础上,研究干支流淤积形态的变化,重点研究支流口门拦门沙坎抬升变化特征,结果表明：支流的分流及淤积与入库流量、含沙量及库区的淤积形态有关.入库流量越大,支流分流比小,支流淤积规模小;入库含沙量越大,支流分沙比越大,支流淤积规模越大.     

Morphodynamic evolution of a lower Mississippi River channel bar after sand mining

In‐channel sand mining by dredge removes large quantities of bed sediment and alters channel morphodynamic processes. While the reach‐scale impacts of dredging are well documented, the effects of the dredged borrow pit on the local flow and sediment transport are poorly understood. These local effects are important because they control the post‐dredge evolution of the borrow pit, setting the pit lifespan and affecting reach‐scale channel morphology. This study documents the observed morphological evolution of a large (1·46 million m³) borrow pit mined on a lateral sandbar in the lower Mississippi River using a time‐series of multibeam bathymetric surveys. During the 2·5 year time‐series, 53% of the initial pit volume infilled with sediment, decreasing pit depth by an average of 0·88 m yr^?1. To explore the controls of the observed infilling, a morphodynamic model (Delft3D) was used to simulate flow and sediment transport within the affected river reach. The model indicated that infilling rates were primarily related to the riverine sediment supply and pit geometry. The pit depth and length influenced the predicted magnitude of the pit bed shear stress relative to its pre‐dredged value, i.e. the bed‐stress reduction ratio (R*), a metric that was correlated with the magnitude and spatial distribution of infilling. A one‐dimensional reduced‐complexity model was derived using predicted sediment supply and R* to simulate patterns of pit infilling. This simplified model of borrow‐pit evolution was able to closely approximate the amount and patterns of sediment deposition during the study period. Additional model experiments indicate that, for a borrow pit of a set volume, creating deep, longitudinally‐shorter borrow pits significantly increased infilling rates relative to elongated pits. Study results provide insight into the resilience of alluvial river channels after a disturbance and the sustainability of sand mining as a sediment source for coastal restoration. Copyright © 2015 John Wiley & Sons, Ltd.     

EXPERIMENTAL INVESTIGATION AND ANALYSIS OF HEC-6 RIVER MORPHOLOGICAL MODEL

Only comparatively few experimental studies have been carried out to investigate the performance of the HEC-6 river morphological model. The model was developed by the Hydrologic Engineering Center of the US Army Corps of Engineers. In this study, experiments were carried out in a 20 m long concrete flume 0.6 m wide with varying rectangular cross-sections. The channel bed is paved with uniform sand of D₅₀ = 0.9 mm and D₉₀ = 1.2 mm within the test reach of 12 m. Two types of experiments were carried out with sediment transport, one under steady uniform flow and another under steady non-uniform flow conditions. Nine steady uniform flow experiments were carried out to compare the measured equilibrium relationship of flow and sediment transport rate with two bedload formulae, namely, Du Boys and Meyer–Peter and Muller, and with three total load formulae, namely, Toffaleti, Laursen and Yang. It was found that even though the sediment transport consists of a certain portion of bedload, the total load formulae give satisfactory results and better agreement than the two bedload formulae. Five steady non-uniform flow experiments were carried out under various conditions of varying bed profile and channel width and also with sediment addition and withdrawal. The measured transient water surface and bed profiles are compared with the computed results from the HEC-6 model. It was found that the Toffaleti and Yang total load formulae used in the HEC-6 model give the most satisfactory prediction of actual bed profiles under various conditions of non-uniform flow and sediment transport. The effects of Manning's n, variations of sediment inflow, various sediment transport formulae, sediment grain size and the model numerical parameters, i.e. distance interval Δx and numerical weighting factor, on the computed water surface and bed profiles were determined. It was found that the selection of the sediment transport formulae has the most significant effect on the computed results. It can be concluded that the HEC-6 model can predict satisfactorily a long-term average pattern of local scour and deposition along a channel with either a small abrupt change in geometry or gradually varying cross-sections. However, the accuracy of the model prediction is reduced in the regions where highly non-uniform flow occurs.     

Dynamic model for constriction scour caused by large woody debris

Large woody debris (LWD) can have a significant impact upon local channel morphology by creating scour pools and zones of reduced shear stress in which sediment is deposited. It is important to predict scour depths associated with LWD, as it is becoming increasingly common for debris to be added into river channels to improve sediment retention and create pools for aquatic habitat. Engineered log‐jams should therefore be designed using factor of safety engineering analysis, which includes estimates of associated scour and deposition rates. However, the rate and total depth of scour associated with LWD have not been modelled comprehensively, with authors resorting to the use of generic local and constriction scour models to predict scour depths. Also, constriction scour models presented, to date, do not calculate the rate of scour development. In this paper a model is presented for predicting the rate and total depth of scour associated with a channel constriction. The model is one‐dimensional and is based upon the sediment continuity equation, the calculation of specific head changes through the constricted reach and also allows for a variable free surface elevation above the bed at the constriction. This model could be applied to any channel constriction problem but here is used to determine scour rates and depths associated with deflector‐type LWD jams. Deflector jams are one category of jam type presented in a debris jam classification scheme, in which jam type is a function of the ratio of average riparian tree height to average channel width. Deflector jams, as the name implies, partially block the flow and therefore act as a channel constriction, which results in constriction scour. Copyright © 2002 John Wiley & Sons, Ltd.     

NUMERICAL SIMULATION OF RIVER BED CHANGE AT SIMAO PORT

LINTRODUCTIONJinghongHydraulicPowerPlant,locatedintheload,erreachesofLanchangmyer,trib.ofMekong,isintheNorthOfJinghongCity.Thepowerstationisamultipurposehydro-junction,includingelectricpowergeneration,shipping,floodcontrol,cultivahonandwatersupply.SimaoPort,animportanttransportcenterinSimaoDistriCt,YunnanProvince,isabollt80kmaamsuPStreamofthedam.Anerthereservoirisimpounded,thewaterstagewillriseandagreatamountofsedimentwillbedepositedintheriverbedinevitably.Asaresult,itisverylikelyt…     

The response of a gravel‐bed river planform configuration to flow variations and bed reworking: a modelling study

A 2D depth‐averaged model has been developed for simulating water flow, sediment transport and morphological changes in gravel‐bed rivers. The model was validated with a series of laboratory experiments and then applied to the Nove reach of the Brenta River (Northern Italy) to assess its bed material transport, interpret channel response to a series of intensive flood events (R.I. ≈ 10 years) and provide a possible evolutionary scenario for the medium term. The study reach is 1400 m long with a mean slope of 0.0039 m m^?1. High‐resolution digital terrain models were produced combining LiDAR data with colour bathymetry techniques. Extensive field sedimentological surveys were also conducted for surface and subsurface material. Data were uploaded in the model and the passage of two consecutive high intensity floods was simulated. The model was run under several hypotheses of sediment supply: one considering substantial equilibrium between sediment input and transport capacity, and the others reducing the sediment supply. The sediment supply was then calibrated comparing channel morphological changes as observed in the field and calculated by the model. Annual bed material transport was assessed and compared with other techniques. Low‐frequency floods (R.I. ≈ 1.5 years) are expected to produce negligible changes in the channel while high floods may erode banks rather than further incising the channel bed. Location and distribution of erosion and deposition areas within the Nove reach were predicted with acceptable biases stemming from imperfections of the model and the specified initial, boundary and forcing conditions. A medium‐term evolutionary scenario simulation underlined the different response to and impact of a consecutive sequence of floods. Copyright © 2015 John Wiley & Sons, Ltd.     

Channel response to a dam-removal sediment pulse captured at high-temporal resolution using routine gage data

In this study, we captured how a river channel responds to a sediment pulse originating from a dam removal using multiple lines of evidence derived from streamflow gages along the Patapsco River, Maryland, USA. Gages captured characteristics of the sediment pulse, including travel times of its leading edge (~7.8 km yr⁻¹) and peak (~2.6 km yr⁻¹) and suggest both translation and increasing dispersion. The pulse also changed local hydraulics and energy conditions, increasing flow velocities and Froude number, due to bed fining, homogenization and/or slope adjustment. Immediately downstream of the dam, recovery to pre-pulse conditions occurred within the year, but farther downstream recovery was slower, with the tail of the sediment pulse working through the lower river by the end of the study 7 years later. The patterns and timing of channel change associated with the sediment pulse were not driven by large flow or suspended sediment-transporting events, with change mostly occurring during lower flows. This suggests pulse mobility was controlled by process-factors largely independent of high flow. In contrast, persistent changes occurred to out-of-channel flooding dynamics. Stage associated with flooding increased during the arrival of the sediment pulse, 1 to 2 years after dam removal, suggesting persistent sediment deposition at the channel margins and nearby floodplain. This resulted in National Weather Service-indicated flood stages being attained by 3–43% smaller discharges compared to earlier in the study period. This study captured a two-signal response from the sediment pulse: (1) short- to medium-term (weeks to months) translation and dispersion within the channel, resulting in aggradation and recovery of bed elevations and changing local hydraulics; and (2) dispersion and persistent longer-term (years) effects of sediment deposition on overbank surfaces. This study further demonstrated the utility of US Geological Survey gage data to quantify geomorphic change, increase temporal resolution, and provide insights into trajectories of change over varying spatial and temporal scales.     

RETROGRESSIVE EROSION AND LONGITUDINAL PROFILE EVOLUTION IN NONCOHESIVE MATERIAL

1 INTRODUCTION A headcut, which is an abrupt break in the slope of a channel bed, is often called a “knickpoint” or “scarp” in the study of rivers and waterways. A headcut tends to retreat upstream as water flows over it. As a headcut passes a cross s…     

A simulation model of morphological,vegetation and sediment changes in ephemeral streams

A model to simulate channel changes in ephemeral river channels and to test the effects of hydrological changes due to climate change and[sol ]or land use change was developed under the auspices of the EU funded MEDALUS programme (Mediterranean Desertification and Land Use). The model, CHANGISM (Channel Change GIS Simulation Model), is designed to simulate the effect of channel flow events and of climate conditions on morphology, sediment and vegetation, through sequences of events and conditions, over periods of up to several decades. The modelling is based on cellular automata but with calculations for water and sediment continuity. Process rules have both deterministic and stochastic elements. An important feature of the model is that it incorporates feedback elements between each event. The main aim of the model is to indicate the likely outcomes of events and combinations of conditions. It is linked to GIS for both input and output. The modelling is based on a channel reach and state is input as GIS layers of morphology (DEM), sediment and vegetation cover and state. Other initial conditions of soil moisture, groundwater level, and overall gradient are input. Parameters for processes are read from tables and can be easily changed for successive runs of the model. The bases for decisions on process specifications are discussed in this paper. Initial tests of the operation and sensitivity of the model were made on idealized reaches. The model was then tested using data from monitored sites in SE Spain. Simulations using clearwater flow worked well but initial simulations using events with sediment loads showed some tendency for excess deposition. Further tests and modifications are taking place. Overall, the model is one of the most sophisticated that simulates the interaction of flows with sediment and vegetation and the outcomes in terms of erosion, deposition, morphology, sediment cover, vegetation cover and plant survival over periods of up to 30 years for the scale of a channel reach. Copyright © 2005 John Wiley & Sons, Ltd.