Investigation of a shallow alluvial aquifer using geoelectrical methods: a case from Turkey

Near-surface geophysical methods are commonly used to solve a wide class of geological, engineering and environmental problems. In this study, a geoelectrical survey was performed to investigate an alluvial aquifer. The study area is located in the southwest of the Çubukluda? graben, situated in the south of ?zmir, Turkey. The geophysical studies included the electrical resistivity imaging and self-potential (SP) methods. The resistivity data were acquired along eight profiles in the northern part of the study area by a Wenner-Schlumberger electrode configuration and the data processing was achieved by a tomographic inversion technique. The SP data were collected by gradient technique along 16 profiles. Total field values were calculated for each profile by addition of the successive gradient values, then a total field SP map was obtained. The water-saturated zone in the northern part of the study area was clearly revealed by the electrical resistivity imaging and the SP survey yielded useful information on the subsurface fluid movement.     

利用滨海地下水潮汐效应估计含水层参数:以北海半岛为例

通过分析滨海含水层中观测孔的水位动态资料,确定含水层的水力性质和某些参数,或推测含水层在海底的延伸长度和露头处是否存在覆盖层,是水文地质学家一直很感兴趣的问题之一。文中充分分析了广西北海半岛滨海地区水文地质条件,将研究区第一个承压含水层系统概化为具有上覆弱透水层越流和含水层海底露头覆盖层的垂向三层结构的不稳定流模型。应用该模型的解析解对广西北海半岛滨海含水层系统的观测数据进行了分析,拟合效果很好,并利用最小平方罚函数法估算了研究区含水层的参数。     

Estimation of aquifer hydraulic parameters from surface geophysical measurements: a case study of the Upper Cretaceous aquifer, central Sinai, Egypt

The integration of geophysical data with direct hydrogeological measurements can provide a minimally invasive approach to characterize the subsurface at a variety of resolutions and over many spatial scales. The field of hydrogeophysics has attracted much attention during the last two decades. In this domain, the geophysical data inverted to geophysical models are interpreted in terms of the hydrogeology to serve as a basis for the definition of hydraulic models in the areas of interest. The hydraulic conductivity (K) value measured in a reference borehole has been combined with the electrical conductivity obtained from nearby geo-electromagnetic sounding data in the Cenomanian (Upper Cretaceous) aquifer, central Sinai, Egypt. The resulting relation was interpreted with Dar Zarrouk parameters to infer the transmissivity variations at other vertical electrical sounding locations, where K values are unknown. Coincident transient electromagnetic data have been adopted to increase accuracy while interpreting the aquifer geoelectrical properties. The results indicate that the transmissivity values in the aquifer of interest vary from 2,446 to 9,694 m²/day, and K varies from 12.9 to 57.0 m/day throughout the studied area.     

Identifying vulnerable areas of aquifer under future climate change (case study: Hamadan aquifer,West Iran)

Groundwater is the main source of water in arid and semi-arid regions, so it is very important to recognize vulnerable parts of aquifer under future climate change conditions. In this research, 16 climate models were evaluated based on weighting approach. HADCM3 and CGCM2.3.2a models were selected for temperature and precipitation prediction, respectively. LARS-WG was used for downscaling AOGCMs outputs. Results show that temperature increase by 1.4 °C and precipitation changes between +10 and ?6 % under B1 and A2 emission scenario, respectively. Runoff volumes will decrease by ?39 % under A2 emission scenario whereas runoff volume will increase by +12 % under B1 emission scenario. Simulation of groundwater head variation by MODFLOW software indicates higher groundwater depletion rate under A2 scenario compared to B1 scenario. Groundwater model outputs indicate that the most vulnerable part of the aquifer is located in the southwest region. Large number of extraction wells and low aquifer transmissivity are the reasons for high vulnerability of the region.     

Hydrogeological and hydrochemical framework of regional aquifer system in Kali-Ganga sub-basin, India

 The central Ganga Basin is one of the major groundwater reservoirs in India. The Kali-Ganga sub-basin is a micro watershed of the central Ganga Basin, containing a number of productive aquifers. A detailed hydrogeological investigation was carried out, which reveals the occurrence of a single-tier aquifer system down to 163 m bgl (metres below ground level), but at places it is interleaved with clay layers; thus imparting it a two-to three-tier aquifer system. These aquifers are unconfined to confined in disposition. The transmissivity, storage coefficient and hydraulic conductivity are determined as 2178 m²/day, 1.12×10^–5 and 120 m/day, respectively. The groundwater of the basin is fresh, of an alkali-bicarbonate type and is suitable for irrigation and domestic use. However, in certain areas, extensive agricultural activities, and domestic and industrial effluents have caused some deterioration of groundwater quality. This study contains data of where the concentration of Fe, Pb, Cd, Cr and Ni are higher than the permissible limits, which may be hazardous to public health. Received: 2 March 2000 · Accepted: 3 July 2000     

Automatic estimation of aquifer parameters using long-term water supply pumping and injection records

Analyses are presented of long-term hydrographs perturbed by variable pumping/injection events in a confined aquifer at a municipal water-supply well field in the Region of Waterloo, Ontario (Canada). Such records are typically not considered for aquifer test analysis. Here, the water-level variations are fingerprinted to pumping/injection rate changes using the Theis model implemented in the WELLS code coupled with PEST. Analyses of these records yield a set of transmissivity (T) and storativity (S) estimates between each monitoring and production borehole. These individual estimates are found to poorly predict water-level variations at nearby monitoring boreholes not used in the calibration effort. On the other hand, the geometric means of the individual T and S estimates are similar to those obtained from previous pumping tests conducted at the same site and adequately predict water-level variations in other boreholes. The analyses reveal that long-term municipal water-level records are amenable to analyses using a simple analytical solution to estimate aquifer parameters. However, uniform parameters estimated with analytical solutions should be considered as first rough estimates. More accurate hydraulic parameters should be obtained by calibrating a three-dimensional numerical model that rigorously captures the complexities of the site with these data.     

Use of chloride mass balance and tritium data for estimation of groundwater recharge and renewal rate in an unconfined aquifer from North Africa: a case study from Tunisia

The scarcity of surface water resources in arid and semi-arid regions from North African countries contributes to the considerable increase of groundwater exploitation, which leads to the development of hydrogeological studies. However, due to the lack of hydrodynamic data in these regions, these studies focus more and more on the geochemical and environmental isotope techniques to insure a better understanding of the hydrodynamic functioning of subsurface systems. In this study, which interests an important unconfined aquifer in central Tunisia, tritium data and chloride mass balance (CMB) method were applied in order to (1) understand the mode of recharge of this aquifer and (2) obtain a reliable estimation of its recharge amount as well as (3) estimate its annual renewal rate. It has been demonstrated that the shallow groundwaters are classified into two groups according to their tritium contents. The first group includes wells located mainly downstream and highlights the significant role of the post-nuclear lineal recharge through Wadis courses. The second group encloses wells located practically overall the rest of the basin and refers to relatively modern waters originated from areal recharge of present-day rainfall. Based on the CMB method, the recharge to this unconfined aquifer is estimated to 31.7 mm year⁻¹, which corresponds to 10.5% of the total rainfall. The annual renewal rate of groundwater, evaluated based on the tritium contents, is up to 16%.     

Well modeling and estimation of hydraulic parameters

A general model for time‐dependent saturated–unsaturated waterflow caused by a single well with a given radius is presented. The storage capacity of the well tube is taken into account. The inflow into the well (with drainage) is modeled using the Signorini boundary condition. The nonconforming mixed finite element method on a multilevel adaptive grid is used for the solution of the radial symmetric, time dependent problem. Finally, van Genuchten parameters of an aquifer are determined from field measurements by inverse computations.     

用地下水化学动力学方法计算出的水文地质参数来定量评价水文地质条件--以太原三给地垒及周围地区为例

作者根据研究区内剖分获得429个结点的原始资料,分别计算出K、T、u、U、t等5个水文地质参数各429个,利用计算结果,编制K值和T值分区图及地下水循环条件图,对研究区水文地质条件进行了定量评价.该方法为其它岩溶区水文地质条件进行定量评价提供了一条有效的新途径.     

利用CFCs定年数据计算静升盆地含水层渗透系数

文章利用CFCs(氟氯碳化合物)定年数据,计算山西静升盆地含水层渗透系数。结果表明:补给条件较好的区域与补给条件差的深层承压区相比,地下水年龄偏年轻;从冲洪积扇顶部到扇缘,地下水径流逐渐变缓,含水层渗透系数变小;盆地南部较北部,地下水流动缓慢,渗透系数整体偏小。该方法获得的渗透系数符合实际地质条件。     

Impact of model complexity and multi-scale data integration on the estimation of hydrogeological parameters in a dual-porosity aquifer

This study investigates the impact of model complexity and multi-scale prior hydrogeological data on the interpretation of pumping test data in a dual-porosity aquifer (the Chalk aquifer in England, UK). In order to characterize the hydrogeological properties, different approaches ranging from a traditional analytical solution (Theis approach) to more sophisticated numerical models with automatically calibrated input parameters are applied. Comparisons of results from the different approaches show that neither traditional analytical solutions nor a numerical model assuming a homogenous and isotropic aquifer can adequately explain the observed drawdowns. A better reproduction of the observed drawdowns in all seven monitoring locations is instead achieved when medium and local-scale prior information about the vertical hydraulic conductivity (K) distribution is used to constrain the model calibration process. In particular, the integration of medium-scale vertical K variations based on flowmeter measurements lead to an improvement in the goodness-of-fit of the simulated drawdowns of about 30%. Further improvements (up to 70%) were observed when a simple upscaling approach was used to integrate small-scale K data to constrain the automatic calibration process of the numerical model. Although the analysis focuses on a specific case study, these results provide insights about the representativeness of the estimates of hydrogeological properties based on different interpretations of pumping test data, and promote the integration of multi-scale data for the characterization of heterogeneous aquifers in complex hydrogeological settings.     

Estimating hydraulic parameters of a heterogeneous aquitard using long-term multi-extensometer and groundwater level data

The classical aquitard-drainage model COMPAC has been modified to simulate the compaction process of a heterogeneous aquitard consisting of multiple sub-units (Multi-COMPAC). By coupling Multi-COMPAC with the parameter estimation code PEST++, the vertical hydraulic conductivity (K _v) and elastic (S _ske) and inelastic (S _skp) skeletal specific-storage values of each sub-unit can be estimated using observed long-term multi-extensometer and groundwater level data. The approach was first tested through a synthetic case with known parameters. Results of the synthetic case revealed that it was possible to accurately estimate the three parameters for each sub-unit. Next, the methodology was applied to a field site located in Changzhou city, China. Based on the detailed stratigraphic information and extensometer data, the aquitard of interest was subdivided into three sub-units. Parameters K _v, S _ske and S _skp of each sub-unit were estimated simultaneously and then were compared with laboratory results and with bulk values and geologic data from previous studies, demonstrating the reliability of parameter estimates. Estimated S _skp values ranged within the magnitude of 10^?4 m^?1, while K _v ranged over 10^?10–10^?8 m/s, suggesting moderately high heterogeneity of the aquitard. However, the elastic deformation of the third sub-unit, consisting of soft plastic silty clay, is masked by delayed drainage, and the inverse procedure leads to large uncertainty in the S _ske estimate for this sub-unit.     

Resource estimation from historical data: Mercury, a test case

A simple technique based on historical records of tonnage and grade of ore produced provides a means for calculating how much of a mineral product will be available in the future at various average grades. Estimates made on this basis are independent of geologic considerations or changing economic and political factors, although they are based on mining history, which was largely determined by these factors. The relatively minor element, mercury, was used for the test case reported here, but the method has been found applicable to forecasts of resources for other mineral products. Mercury resources available in ore in which the average grade is as low as 0.1% are estimated to be 53 ×10 ⁶ kg (1.5 ×10 ⁶ flasks) for the United States and 1551 ×10 ⁶ kg (45 ×10 ⁶ flasks) for the world; this amount is more than adequate to meet predicted demand to the year 2000. The expectable price of mercury in 1978 dollars at this 0.1% grade is projected to be $58.75 per kg ($2,025 per flask), but at a 10% annual inflation rate, it would be more than $12,000 per flask. To satisfy just the projected U.S. demand for mercury by 2000, the price is calculated to be $48.96 per kg ($1,688 per flask) in 1978 dollars at an average annual grade of 0.12%.     

Hydrogeological characterization of a carbonate aquifer using geophysical and geochemical approach: case of the Krachoua Formation in Tataouine area,Southern Tunisia

An integrated hydrogeological investigation involving geological surface data, well data (lithostratigraphical and piezometric data) and the vertical electrical sounding (VES) method was carried out in Tataouine area, Southern Tunisia to characterize the hydrogeology and the geochemistry of the Krachoua Formation aquifer. The electrical data were used to differentiate lithostratigraphic units and characterize their hydrogeological potentialities. Major elements contents within groundwater samples were assessed and some plots and diagrams have been established in order to investigate the hydrochemical properties of this aquifer and the origin of its mineralization. The Krachoua aquifer exhibits a general drawdown of the piezometric level from 2004 to 2015 reflecting a dramatic decrease in groundwater resources due to increased groundwater abstraction during the last decades. Flow directions shows that the recharge of this aquifer considered as a free aquifer is directly ensured by rainfalls over the outcropping fractured limestones. The geometry of the Krachoua Formation aquifer is tectonically controlled and structured in horst and graben features that impacted greatly the hydrogeology and the hydrodynamics of the area. Subsequent thickness and facies variations within this aquifer influenced the reservoir quality and the groundwater flows. The increased values of salinity to the northwest of the study area seems to be mainly related to the dissolution of the Upper Liassic gypsum of Mestaoua Formation which outcrops widely and can be dissolute easily by meteoric water and contaminate the Krachoua aquifer. This fact is also supported by the sulfated and calci-magnesian chloride facies of this aquifer related to the dissolution of evaporitic rocks (gypsum, anhydrite, and halite). However low salinity values are recorded within the zone where these evaporitic rocks are relatively deep.     

Interpreting sustainable yield of an aquifer using a fuzzy framework

Reliable estimates for how much water can be safely withdrawn from aquifers without harming the environment is crucial for identifying new water supply sources and fostering sustainable growth. Methodologies to estimate groundwater availability that are rooted in science and yet accomplishable with minimal data are particularly useful for effectual aquifer management. Also, as groundwater management is increasingly becoming a participatory process, these methodologies must be transparent and easily understood by a wide range of audiences. In addition, proposed approaches must also reconcile imprecision and uncertainties arising from lack of data, differences in stakeholders’ perceptions and limitations associated with incomplete aquifer characterization. In this study, the fundamental concept of water balance is coupled with fuzzy regression to develop a scheme for assessing regional-scale groundwater availability. Using the mass-balance approach, anthropogenic water demands (municipal, industrial and agricultural) and ecological demands (baseflows to rivers) can be incorporated into the availability estimation process. The use of fuzzy regression enables the specification of decision makers’ preferences to the adopted procedure and renders the parameter estimation to be more robust in the presence of extreme values. The methodology is illustrated by using it to estimate groundwater availability in the Gulf coast aquifer, underlying Refugio County, TX, USA.     

Classifying zones of suitability for manual drilling using textural and hydraulic parameters of shallow aquifers: a case study in northwestern Senegal

A method is proposed that uses analysis of borehole stratigraphic logs for the characterization of shallow aquifers and for the assessment of areas suitable for manual drilling. The model is based on available borehole-log parameters: depth to hard rock, depth to water, thickness of laterite and hydraulic transmissivity of the shallow aquifer. The model is applied to a study area in northwestern Senegal. A dataset of boreholes logs has been processed using a software package (TANGAFRIC) developed during the research. After a manual procedure to assign a standard category describing the lithological characteristics, the next step is the automated extraction of different textural parameters and the estimation of hydraulic conductivity using reference values available in the literature. The hydraulic conductivity values estimated from stratigraphic data have been partially validated, by comparing them with measured values from a series of pumping tests carried out in large-diameter wells. The results show that this method is able to produce a reliable interpretation of the shallow hydrogeological context using information generally available in the region. The research contributes to improving the identification of areas where conditions are suitable for manual drilling. This is achieved by applying the described method, based on a structured and semi-quantitative approach, to classify the zones of suitability for given manual drilling techniques using data available in most African countries. Ultimately, this work will support proposed international programs aimed at promoting low-cost water supply in Africa and enhancing access to safe drinking water for the population.     

Geochemistry of groundwater from a rhyolite aquifer,Northwest Iran

Chemical data on groundwater composition in rhyolitic hard rock aquifers with limited global occurrence are rarely found. In this research geochemistry of Mahabad Rhyolite Aquifer, NW Iran, was studied considering major ions, silica and trace elements measured in wet and dry seasons. Based on the results, the mean silica content was 18 mg l^?1, less than the average of the rhyolitic waters. However, the relatively higher electrical conductivity (EC) of 418 µS cm^?1 was measured. Based on a PHREEQCI model, the weathering of the silicate minerals and dissolution of carbonated intercalations turns groundwater dominantly into Ca–HCO₃ type, enhancing EC, pH and silica concentration along the flow path. Trace elements of Sr, Ba and Pb were measured at highest concentrations, the later with an average value of 83 ppb exceeds the drinking guidelines. Cluster analysis confirms biotite weathering and barite dissolution as the main sources of the trace elements in the groundwater. The results signify geochemical features of rhyolitic groundwater which can be a useful tracer of mixing in flow systems containing variety of aquifers including rhyolites.     

Determination of heterogeneities in the hydraulic properties of a phreatic aquifer from tidal level fluctuations: a case in Argentina

A well-known analytical solution of Jacob (1950) for groundwater flow due to tidal-wave propagation, together with field measurements along a complete tidal cycle and geological data, were used to evaluate the heterogeneities in the hydraulic properties of a phreatic aquifer located next to the River Ajo in the coastal plain environment of the southern sector of the Samborombon Bay wetland, Argentina. From the analysis of water-table fluctuations in a set of monitoring wells located along a riverbank-normal transect, it was possible to quantify the piecewise spatial variations of the hydraulic diffusivity of the phreatic aquifer. The results show the strong lateral variations of the sedimentary environment due to the influence of the different transport and deposition agents that characterize the coastal plain. The known thickness of the phreatic aquifer and the estimated range of the specific yield allowed the hydraulic conductivity to be identified as the most influential factor. [Jacob CE (1950) Flow of ground water. In: Rouse H (ed) Engineering Hydraulics. Wiley, New York]