Application of stacking and inversion techniques to three-dimensional wide-angle reflection and refraction seismic data of the Eastern Alps

We present new methods for the interpretation of 3-D seismic wide-angle reflection and refraction data with application to data acquired during the experiments CELEBRATION, 2000 and ALP 2002 in the area of the Eastern Alps and their transition to the surrounding tectonic provinces (Bohemian Massif, Carpathians, Pannonian domain, Dinarides). Data was acquired on a net of arbitrarily oriented seismic lines by simultaneous recording on all lines of seismic waves from the shots, which allows 2-D and 3-D interpretations. Much (80%) of the data set consists of crossline traces. Low signal to noise (S/N) ratio in the area of the young orogens decreases the quality of travel time picks. In these seismically heterogeneous areas it is difficult to assign clearly defined arrivals to the seismic phases, in particular on crossline record sections.
In order to enhance the S/N ratio, signal detection and stacking techniques have been applied to enhance the Pg -, Pn - and PmP phases. Further, inversion methods have been developed for the interpretation of WAR/R-data, based on automated 1-D inversion ( Pg ) and the application of the delay time concept ( Pn ). The results include a 3-D velocity model of the crust based on Pg waves, time and depth maps of the Moho and a Pn -velocity map. The models based on stacked data are robust and provide a larger coverage, than models based on travel time picks from single-fold (unstacked) traces, but have relatively low resolution, especially near the surface. They were used as the basis for constructing models with improved resolution by the inversion of picks from single-fold data. The results correlate well with geological structures and show new prominent features in the Eastern Alps area and their surrounds. The velocity distribution in the crust has strong lateral variations and the Moho in the investigation area appears to be fragmented into three parts.     

Generalized Born inversion of seismic reflection data

Summary . Born inverse methods give accurate and stable results when the source wavelet is impulsive. However, in many practical applications (reflection seismology) an impulsive source cannot be realized and the inversion needs to be generalized to include an arbitrary source function. In this paper, we present a Born solution to the seismic inverse problem which can accommodate an arbitrary source function and give accurate and stable results. It is shown that the form of the generalized inversion algorithm reduces to a Wiener shaping ***filter, which is solved efficiently using a Levinson recursion algorithm. Numerical examples of synthetic and real field data illustrate the validity of our method.     

Modelling and inversion of single-ended refraction data from the shot gathers of multifold deep seismic reflection profiling—an approach for deriving the shallow velocity structure

A multifold crustal-scale deep seismic near-vertical reflection profile generates a large number of single-ended shot gathers, which provide redundant data sets because of overlapping coverage of the shallow refractors. We present an approach for deriving the shallow velocity structure by modelling and inversion of single-ended seismic refraction first arrival traveltime data. We apply this method to a data set acquired with a 12-km long spread with 100 m spacing of shots and receivers, of the Neoproterozoic Marwar basin in the NW Indian shield. The approach is shown to be quite successful for delineating the shallow refractor depths, steep dips and velocities, even in the absence of regular reverse refraction profiles. The study reveals two-layered sedimentary formations, Malani volcanics and a complicated basement configuration of the Marwar basin, and provides a measure of resolution and uncertainty of the estimated model parameters. A seismic section of the near-trace gather is found to be qualitatively consistent with the derived structural features of the basin. The relative highs and lows, observed in the Bouguer gravity profile, further corroborate the derived velocity model. The present approach can be especially useful in offshore areas and elsewhere, where the single-ended multifold seismic profiles are the only available data sets.     

Crustal and upper mantle structure of the northwestern North Island, New Zealand, from seismic refraction data

The crustal and upper mantle structure of the northwestern North Island of New Zealand is derived from the results of a seismic refraction experiment; shots were fired at the ends and middle of a 575 km-long line extending from Lake Taupo to Cape Reinga. The principal finding from the experiment is that the crust is 25 ± 2 km thick, and is underlain by what is interpreted to be an upper mantle of seismic velocity 7.6 ± 0.1 km s⁻¹, that increases to 7.9 km s⁻¹ at a depth of about 45 km. Crustal seismic velocities vary between 5.3 and 6.36 km s⁻¹ with an average value of 6.04 km s⁻¹. There are close geophysical and geological similarities between the north-western North Island of New Zealand and the Basin and Range province of the western United States. In particular, the conditions of low upper-mantle seismic velocities, thin crust with respect to surface elevation, and high heat-flow (70–100 mW m⁻²) observed in these two areas can be ascribed to their respective positions behind an active convergent margin for about the past 20 Myr.     

Lithology-derived structure classification from the joint interpretation of magnetotelluric and seismic models

Magnetotelluric and seismic methods provide complementary information about the resistivity and velocity structure of the subsurface on similar scales and resolutions. No global relation, however, exists between these parameters, and correlations are often valid for only a limited target area. Independently derived inverse models from these methods can be combined using a classification approach to map geologic structure. The method employed is based solely on the statistical correlation of physical properties in a joint parameter space and is independent of theoretical or empirical relations linking electrical and seismic parameters. Regions of high correlation (classes) between resistivity and velocity can in turn be mapped back and re-examined in depth section. The spatial distribution of these classes, and the boundaries between them, provide structural information not evident in the individual models. This method is applied to a 10 km long profile crossing the Dead Sea Transform in Jordan. Several prominent classes are identified with specific lithologies in accordance with local geology. An abrupt change in lithology across the fault, together with vertical uplift of the basement suggest the fault is sub-vertical within the upper crust.     

Sequential integrated inversion of refraction and wide-angle reflection traveltimes and gravity data for two-dimensional velocity structures

A new algorithm is presented for the integrated 2-D inversion of seismic traveltime and gravity data. The algorithm adopts the 'maximum likelihood' regularization scheme. We construct a 'probability density function' which includes three kinds of information: information derived from gravity measurements; information derived from the seismic traveltime inversion procedure applied to the model; and information on the physical correlation among the density and the velocity parameters. We assume a linear relation between density and velocity, which can be node-dependent; that is, we can choose different relationships for different parts of the velocity–density grid. In addition, our procedure allows us to consider a covariance matrix related to the error propagation in linking density to velocity. We use seismic data to estimate starting velocity values and the position of boundary nodes. Subsequently, the sequential integrated inversion (SII) optimizes the layer velocities and densities for our models. The procedure is applicable, as an additional step, to any type of seismic tomographic inversion.
We illustrate the method by comparing the velocity models recovered from a standard seismic traveltime inversion with those retrieved using our algorithm. The inversion of synthetic data calculated for a 2-D isotropic, laterally inhomogeneous model shows the stability and accuracy of this procedure, demonstrates the improvements to the recovery of true velocity anomalies, and proves that this technique can efficiently overcome some of the limitations of both gravity and seismic traveltime inversions, when they are used independently.
An interpretation of field data from the 1994 Vesuvius test experiment is also presented. At depths down to 4.5 km, the model retrieved after a SII shows a more detailed structure than the model obtained from an interpretation of seismic traveltime only, and yields additional information for a further study of the area.