共查询到20条相似文献,搜索用时 31 毫秒
1.
During bedload movement by saltation, streamwise momentum is transferred from the ?ow to the saltating grains. When the grains collide with other grains on the bed or in the ?ow, streamwise momentum is reduced, and there is a decrease in streamwise ?ow velocity and an increase in ?ow resistance, herein termed bedload transport resistance fbt. Based on experiments in two ?umes with ?xed and mobile plane beds and previously published data, an equation is developed that may be used to predict fbt for both capacity and non‐capacity ?ows. The variables in this equation are identi?ed by dimensional analysis and the coef?cients are determined by non‐linear regression. This equation applies to rough turbulent open‐channel ?ows, where the relative submergence is between 1 and 20 and the entire sediment load moves by saltation. An investigation of the relative magnitudes of fbt and grain resistance fc suggests that where dimensionless shear stress θ is less than 1 and saltation is the dominant mode of bedload transport, fbt/fc increases with θ but never exceeds 1. Copyright © 2004 John Wiley & Sons, Ltd. 相似文献
2.
In wind‐driven rains, wind velocity and direction are expected to affect not only energy input of rains but also shallow ?ow hydraulics by changing roughness induced by raindrop impacts with an angle on ?ow and the unidirectional splashes in the wind direction. A wind‐tunnel study under wind‐driven rains was conducted to determine the effects of horizontal wind velocity and direction on sediment transport by the raindrop‐impacted shallow ?ow. Windless rains and the rains driven by horizontal wind velocities of 6 m s?1, 10 m s?1, and 14 m s?1 were applied to three agricultural soils packed into a 20 by 55 cm soil pan placed on both windward and leeward slopes of 7 per cent, 15 per cent, and 20 per cent. During each rainfall application, sediment and runoff samples were collected at 5‐min intervals at the bottom edge of the soil pan with wide‐mouth bottles and were determined gravimetrically. Based on the interrill erosion mechanics, kinetic energy ?ux (Ern) as a rainfall parameter and product of unit discharge and slope in the form of qbSco as a ?ow parameter were used to explain the interactions between impact and ?ow parameters and sediment transport (qs). The differential sediment transport rates occurred depending on the variation in raindrop trajectory and rain intensity with the wind velocity and direction. Flux of rain energy computed by combining the effects of wind on the velocity, frequency, and angle of raindrop impact reasonably explained the characteristics of wind‐driven rains and acceptably accounted for the differences in sediment delivery rates to the shallow ?ow transport (R2 ≥ 0·78). Further analysis of the Pearson correlation coef?cients between Ern and qSo and qs also showed that wind velocity and direction signi?cantly affected the hydraulics of the shallow ?ow. Ern had a smaller correlation coef?cient with the qs in windward slopes where not only reverse splashes but also reverse lateral raindrop stress with respect to the shallow ?ow direction occurred. However, Ern was as much effective as qSo in the sediment transport in the leeward slopes where advance splashes and advance lateral raindrop stress on the ?ow occurred. Copyright © 2004 John Wiley & Sons, Ltd. 相似文献
3.
Vito Ferro 《地球表面变化过程与地形》2003,28(7):707-722
Velocity measurements carried out by an acoustic doppler velocimeter (ADV) in a rectangular laboratory ?ume having a gravel bed are presented. The velocity pro?les are measured in six verticals of the channel cross‐section having an increasing distance (from 4 to 38·5 cm) from the ?ume wall. The experimental runs are carried out for ?ve different bed arrangements, characterized by different concentrations of coarser elements, and for the two conditions of small‐ and large‐scale roughness. For both hydraulic conditions, the velocity measurements are ?rst used to test the applicability of the Dean pro?le and of the logarithmic pro?le corrected by a divergence function proposed in this paper. Then, for each value of the depth sediment ratio h/d84, the non‐dimensional friction factor parameter is calculated by integration of the measured velocity distributions in the different verticals of the cross‐section. Finally a semi‐logarithmic ?ow resistance equation is empirically deduced. Copyright © 2003 John Wiley & Sons, Ltd. 相似文献
4.
Vito Ferro 《地球表面变化过程与地形》2003,28(12):1325-1339
A previously published mixing length (ML) model for evaluating the Darcy–Weisbach friction factor for a large‐scale roughness condition (depth to sediment height ratio ranging from 1 to 4) is brie?y reviewed and modi?ed (MML). Then the MML model and a modi?ed drag (MD) model are experimentally tested using laboratory measurements carried out for gravel‐bed channels and large‐scale roughness condition. This analysis showed that the MML gives accurate estimates of the Darcy–Weisbach coef?cient and for Froude number values greater than 0·5 the MML model coincides with the ML one. Testing of the MD model shows limited accuracy in estimating ?ow resistance. Finally, the MML and MD models are compared with the performance of a quasi‐theoretical (QT) model deduced applying the P‐theorem of the dimensional analysis and the incomplete self‐similarity condition for the depth/sediment ratio and the Froude number. Using the experimental gravel‐bed data to calibrate the QT model, a constant value of the exponent of the Froude number is determined while two relationships are proposed for estimating the scale factor and the exponent of the depth/sediment ratio. This indirect estimate procedure of the coef?cients (b0, b1 and b2) of the QT model can produce a negligible overestimation or underestimation of the friction factor. Copyright © 2003 John Wiley & Sons, Ltd. 相似文献
5.
A wave‐?ume experiment was conducted to examine the formative condition for three types of distinctive bedforms that emerged through deformation of existing ripples due to waning wave power. They were ripple marks with: (1) a single secondary crest, (2) double secondary crests, and (3) a rounded crest. Data were analysed using two parameters, kh and d0/λ*, where k is the wave number, h is the water depth, d0 is the near‐bottom orbital diameter, and λ* is the spacing of existing ripples. The former quantity, kh, was employed as a surrogate for the degree of ?ow asymmetry. The result showed that ripples with secondary crests developed under a rather symmetrical ?ow ?eld with kh ? 0·7, if d0/λ* ? 1·2, whereas rounded‐crest ripples emerged under asymmetrical ?ow ?eld with kh ? 0·7, if d0/λ* ? ?2·9 kh + 3·2. The number of secondary crests, which initially occurred in each trough, was single if d0/λ* ? 0·8, or double if d0/λ* ? 0·8. Copyright © 2004 John Wiley & Sons, Ltd. 相似文献
6.
David Dunkerley 《地球表面变化过程与地形》2004,29(8):1011-1026
Soil surface microtopography produces non‐uniform surface run‐off, in which narrow threads of relatively deep and fast ?ow move within broader, shallower, slower‐moving regions. This kind of ?ow is probably widespread, given that microtopography is itself common. Methods used to record the properties of surface run‐off include grid‐ or transect‐based depth observations, with a single mean ?ow speed derived by calculation from V = Q/WD, and the use of dye timing to estimate velocity, with an effective mean depth calculated from D = Q/WV. Because these methods allow only single, ?ow‐?eld mean values to be derived for V or D, neither is well suited to non‐uniform ?ows. The use of depth data to derive a ?ow‐?eld mean V furthermore implicitly applies area weighting to the depth data; likewise, the use of dye speeds for V inherently overestimates mean V because dye dominantly follows the faster ?ow threads. The associated errors in derived parameters such as friction coef?cients are not readily quanti?ed and appear not to have been addressed previously. New ?eld experiments made on untilled soil surfaces in arid western NSW, Australia, explore these circumstances and the implications for deriving meaningful measures of ?ow properties, including friction coef?cients. On surfaces deliberately chosen for their very subtle microtopography, average thread velocities are shown to be commonly 2·5 times greater than the ?ow‐?eld mean, and locally 6–7 times greater. On the other hand, non‐thread ?ow speeds lie below the ?ow‐?eld mean, on average reaching only 84 per cent of this value, and often considerably less. Flow‐?eld means conceal the existence of regions of the ?ow ?eld whose properties are statistically distinct. Results con?rm that a reliance on ?ow‐?eld average depths yields estimates of friction coef?cients that are biased toward the shallower, high‐roughness parts of the ?ow, while if dye speeds are relied upon the results are biased toward the deeper, smoother threads of ?ow. A new approach to the evaluation of friction coef?cients in non‐uniform ?ows is advanced, involving the determination of separate coef?cients for threads and non‐thread zones of the ?ow ?eld. In contrast, ?ow‐?eld friction coef?cients as they are customarily derived in run‐off plot experiments subsume these distinct coef?cients in proportions that are generally unknown. The value of such coef?cients is therefore questionable. Copyright © 2004 John Wiley & Sons, Ltd. 相似文献
7.
When sediment grains are transported as bed load in overland flow, there is a net transfer of momentum from the flow to the grains. When these grains collide with other grains, whether on the bed or in the flow, streamwise flow velocity decreases and resistance to flow increases. Resistance to flow generated in this manner is termed bed‐load transport resistance. Resistance to flow f over a plane bed may be partitioned into grain resistance fg and bed‐load transport resistance fbt. We use the symbols fbtf and fbtm to denote fbt for flows over fixed beds and over mobile beds, respectively, and we compute the effect of bed mobility on flow resistance fmob by subtracting fbtf from fbtm. The data for this study come from 54 flume experiments with fixed beds and 38 with mobile beds. On average fmob is approximately equal to half of fbtm, which is about one‐quarter of f. Hence, fmob is about one‐tenth of f. Predictive equations are developed for fbtf, fbtm and fmob using dimensional analysis to identify the relevant independent variables and regression analysis to evaluate the coefficients associated with these variables. Values of fmob are always positive which implies that mobile beds offer greater resistance to flow than do fixed beds. Evidently bed‐load grains colliding with mobile beds lose more momentum to the bed than do grains colliding with fixed beds. In other words, grain collisions with mobile beds are less elastic than those with fixed beds. Copyright © 2005 John Wiley & Sons, Ltd. 相似文献
8.
David L. Dunkerley 《地球表面变化过程与地形》2003,28(7):777-786
Tracers, such as ?uorescein dye, are widely employed to measure overland ?ow speeds by time‐of‐travel along measured ?ow paths. Among several disadvantages of this method are the involvement of human reaction time when using stop‐watches, and the relatively long travel path that is consequently needed for reliable timing. Long ?ow paths mean that local variability along the ?ow path cannot be detected. This paper describes a new optical tachometer that overcomes these limitations, as well as offering other advantages. It is based on the use of a small ?oating re?ector target that is carried on the surface tension ?lm, and which passes between two re?ective sensors mounted above the ?ow. The new device allows virtual ‘spot’ measurements of surface ?ow speed over a path as short as 1 cm, and eliminates the in?uence of human reaction time. The new device is battery powered and portable, and provides an improved alternative to dye timing in many ?eld and laboratory applications. Its use will allow the collection of more re?ned data than have hitherto been easily achievable. Copyright © 2003 John Wiley & Sons, Ltd. 相似文献
9.
Much of the published literature relating to reach‐scale total ?ow resistance concentrates on alluvial rivers and little mention is made of the more extreme resistance found in bedrock‐in?uenced river systems. This paper presents the results of a detailed investigation of total ?ow resistance variation for ?ve channel types on the Sabie River, South Africa (cohesive mixed anastomosed, uncohesive mixed anastomosed, mixed pool–rapid, alluvial braided and alluvial single thread) over a range of discharges. Manning's ‘n’ and Darcy‐Weisbach f resistance coef?cients are calculated using Barnes' methodology (H. H. Barnes, US Geological Survey Water Supply Paper 1849, 1967). These data are analysed at the scales of channel type and morphologic unit and the resultant resistance values are compared with the literature. Generally the low‐?ow friction values estimated for the bedrock‐in?uenced channel types are higher than any reported. Flow resistance quanti?cation of the alluvial channel type study sites on the Sabie River produced values slightly higher than earlier studies of similar morphologies. In situations where signi?cant areas of irregular bedrock are exposed (cohesive mixed anastomosed and mixed pool–rapid channel types) the high ?ow resistance coef?cients at low discharges probably re?ect energy dissipation due to hydraulic jumps and internal distortions; however, these values fall as discharge increases to values comparable to those recorded for step–pool rivers. It is suggested that the slightly elevated resistance coef?cients recorded in the alluvial channel types are the result of the vegetation roughness component, operating when the macro‐channel bar features are inundated. Copyright © 2004 John Wiley & Sons, Ltd. 相似文献
10.
Pascale M. Biron Colleen Robson Michel F. Lapointe Susan J. Gaskin 《地球表面变化过程与地形》2004,29(11):1403-1415
Bed shear stress is a fundamental variable in river studies to link ?ow conditions to sediment transport. It is, however, dif?cult to estimate this variable accurately, particularly in complex ?ow ?elds. This study compares shear stress estimated from the log pro?le, drag, Reynolds and turbulent kinetic energy (TKE) approaches in a laboratory ?ume in a simple boundary layer, over plexiglas and over sand, and in a complex ?ow ?eld around de?ectors. Results show that in a simple boundary layer, the log pro?le estimate is always the highest. Over plexiglas, the TKE estimate was the second largest with a value 30 per cent less than the log estimate. However, over sand, the TKE estimate did not show the expected increase in shear stress. In a simple boundary layer, the Reynolds shear stress seems the most appropriate method, particularly the extrapolated value at the bed obtained from a turbulent pro?le. In a complex ?ow ?eld around de?ectors, the TKE method provided the best estimate of shear stress as it is not affected by local streamline variations and it takes into account the increased streamwise turbulent ?uctuations close to the de?ectors. It is suggested that when single‐point measurements are used to estimate shear stress, the instrument should be positioned close to 0·1 of the ?ow depth, which corresponds to the peak value height in pro?les of Reynolds and TKE shear stress. Copyright © 2004 John Wiley & Sons, Ltd. 相似文献
11.
Present‐day understanding of rill dynamics is hampered by a lack of detailed data on velocity distributions in rills. The latter are dif?cult to collect with traditional techniques due to the very low water depths and the relatively high ?ow velocities in rills. The objectives of this paper were to investigate the feasibility of miniaturized acoustic Doppler velocimeter (mADV) measurements in rill ?ow and to explore longitudinal variations in ?ow velocities and their relationship with rill bed morphology. Detailed data on longitudinal ?ow velocity were required to achieve these objectives. A 1·8 m long rill was formed freely in a ?ume at 5° slope and 0·001 m3 s?1 discharge. Rill topography was characterized by an alternation of steps and pools. The ?ume surface was then ?xed to preserve rill roughness. A topographical scanning of the entire ?ume surface was made. Velocity was measured with a mADV along the rill, and at different depths. Flow depth in a longitudinal direction was also measured using an elevation gauge. A strong relationship exists between rill topography and ?ow hydraulics. Over steps, ?ow was unidirectional and rapidly accelerating until a threshold Froude number (Fn) value between 1·3 and 1·7 was reached and a hydraulic jump occurred leading to the formation of a pool. In the pool, the ?ow pattern was multidirectional and complex. The ?ow was subcritical when leaving the pool and accelerated over the next step until the threshold Froude number value was again reached. Energy loss in the rill was concentrated in the pools, mainly due to the action of a hydraulic jump. This mechanism of energy dissipation appeared to be an essential factor in rill formation and bedform evolution. Copyright © 2004 John Wiley & Sons, Ltd. 相似文献
12.
Partitioning resistance to overland flow on rough mobile beds 总被引:1,自引:0,他引:1
For overland flows transporting predominantly bed load over rough mobile beds without rainfall, resistance to flow f may be divided into four components: surface resistance fs, form resistance ff, wave resistance fw, and bed‐mobility resistance fm. In this study it is assumed that f = fs + ff + fw + fm, and an equation is developed for each component. The equations for fs and ff are borrowed from the literature, while those for fw and fm are developed from two series of flume experiments in which the beds are covered with various concentrations of large‐scale roughness elements. The first series consists of 65 experiments on fixed beds, while the second series contains 194 experiments on mobile beds. All experiments were performed on the same slope (S = 0·114) and with the same size of sediment (D = 0·00074 m). The equations for fw and fm are derived by a combination of dimensional analysis and regression analysis. The analyses reveal that the major controls of fw and fm are the Froude number F and the concentration of the roughness elements Cr. When the equations for fw and fm are summed, the Cr terms cancel out, leaving fw+m = 0·63F?2. An equation is developed that predicts total f, and the contributions of fs, ff, fw and fm to f are computed from the series 1 and 2 experiments. An analysis of the first series reveals that in clear‐water flows over fixed beds, fw accounts for 52 per cent of f. A similar analysis of the second series indicates that in sediment‐laden flows over mobile beds fw comprises 37 per cent and fm 32 per cent of f, so that together fw and fm account for almost 70 per cent of f. Finally, regression analyses indicate that where F > 0·5, fw and fm each vary with F?2 and fw/fm = 1·18. The equation developed here for predicting total f applies only to the range of hydraulic, sediment, and bed roughness conditions represented by the experimental data. With additional data from a broader range of conditions the same methodology as employed here could be used to develop a more general equation. Copyright © 2006 John Wiley & Sons, Ltd. 相似文献
13.
Ivo Thonon Johannes R. Roberti Hans Middelkoop Marcel van der Perk Peter A. Burrough 《地球表面变化过程与地形》2005,30(10):1327-1343
Due to a lack of data on settling velocities (ws) and grain size distributions (GSDs) in ?oodplain environments, sedimentation models often use calibrated rather than measured parameters. Since the characteristics of suspended matter differ from those of deposited sediment, it is impossible to derive the ws and GSD from the latter. Therefore, one needs to measure in situ suspended sediment concentrations (SSCs), settling velocities, effective grain sizes and sedimentation ?uxes. For this purpose we used the LISST‐ST, a laser particle sizer combined with a settling tube. In 2002 (twice) and 2004, we located the LISST‐ST with an optical backscatter sensor and sediment traps in two ?oodplains in The Netherlands: one along the unembanked IJssel River, another along the embanked Waal River. Measurements revealed that the SSC in the ?oodplains varied in relation to the SSC in the river channel. Smaller ?ocs dominated the SSC, while larger ?ocs dominated the potential sedimentation ?uxes. The in situ GSD in the IJssel ?oodplain was signi?cantly coarser than in the Waal ?oodplain, while the dispersed median grain sizes were equal for both ?oodplains. Therefore, the dispersed median grain size was two to ?ve times smaller than the effective one. The in situ grain size exhibited a signi?cant positive relationship with ws, although the ws for the largest ?ocs showed high variability. Consequently, the variability in sedimentation ?uxes was also large. In the actual sedimentation ?uxes, and hence in sedimentation models, in situ grain sizes up to about 20 µm can be neglected. In ?oodplain sedimentation models the relation between settling velocity and in situ grain size can be used instead of Stokes's law, which is only valid for dispersed grain sizes. These models should also use adequate data on ?ow conditions as input, since these strongly in?uence the suspended sediment characteristics. Copyright © 2005 John Wiley & Sons, Ltd. 相似文献
14.
John Pitlick Erich R. Mueller Catalina Segura Robert Cress Margaret Torizzo 《地球表面变化过程与地形》2008,33(8):1192-1209
This study investigates trends in bed surface and substrate grain sizes in relation to reach‐scale hydraulics using data from more than 100 gravel‐bed stream reaches in Colorado and Utah. Collocated measurements of surface and substrate sediment, bankfull channel geometry and channel slope are used to examine relations between reach‐average shear stress and bed sediment grain size. Slopes at the study sites range from 0·0003 to 0·07; bankfull depths range from 0·2 to 5 m and bankfull widths range from 2 to 200 m. The data show that there is much less variation in the median grain size of the substrate, D50s, than there is in the median grain size of the surface, D50; the ratio of D50 to D50s thus decreases from about four in headwater reaches with high shear stress to less than two in downstream reaches with low shear stress. Similar trends are observed in an independent data set obtained from measurements in gravel‐bed streams in Idaho. A conceptual quantitative model is developed on the basis of these observations to track differences in bed load transport through an idealized stream system. The results of the transport model suggest that downstream trends in total bed load flux may vary appreciably, depending on the assumed relation between surface and substrate grain sizes. Copyright © 2007 John Wiley & Sons, Ltd. 相似文献
15.
Coarse bed load was sampled in a gravel/cobble bed stream during two major floods in the snowmelt runoff season. The channel is characterized by high rates of bank erosion and, therefore, high rates of sediment supply and bed load flux. Peak discharge reached four times bank‐full, and bed load was sampled at flows 0·7–1·7 times bank‐full. A large aperture bed load sampler (1 m by 0·45 m) captured the largest particles in motion, and specifically targeted the coarse bed load size distribution by using a relatively large mesh (32 mm or D25 of streambed surface size distribution). Bed load flux was highly variable, with a peak value of 0·85 kg/s/m for the coarse fraction above 38 mm. Bed load size distribution and maximum particle size was related to flow strength. Entrainment was size selective for particles D70 and larger (88–155 mm), while particles in the range D30–D70 (35–88 mm) ceased to move at essentially the same flow. Bed load flux was size selective in that coarse fractions of the streambed surface were under‐represented in or absent from the bed load. Painted tracer particles revealed that the streambed surface in the riffles could remain stable even during high rates of bed load transport. These observations suggest that a large proportion of bed load sediments was sourced from outside the riffles. Repeat surveys confirmed major scour and fill in pools (up to 0·75 m), and bank erosion (>2 m), which together contributed large volumes of sediment to the bed load. Copyright © 2007 John Wiley & Sons, Ltd. 相似文献
16.
A computational study is presented on the hydraulics of a natural pool–rif?e sequence composed of mixed cobbles, pebbles and sand in the River Lune, northern England. A depth‐averaged two‐dimensional numerical model is employed, calibrated with observed data at the ?eld site. From the computational outputs, the occurrence of longitudinally double peak zones of bed shear stress and velocity is found. In particular, at low discharge there exists a primary peak zone of bed shear stress and velocity at the rif?e tail in line with the local maximum energy slope, in addition to a secondary peak at the pool head. As discharge increases, the primary peak at the rif?e tail at low ?ow moves toward the upstream side of the rif?e along with the maximum energy slope, showing progressive equalization to the surrounding hydraulic pro?les. Concurrently, the secondary peak, due to channel constriction, appears to stand at the pool head, with its value increasing with discharge and approaching or exceeding the primary peak over the rif?e. The existence of ?ow reversal is demonstrated for this speci?c case, which is attributable to channel constriction at the pool head. A dynamic equilibrium model is presented to reconstruct the pool–rif?e morphology. A series of numerical modelling exercises demonstrates that the pool–rif?e morphology is more likely produced by shallow ?ows concentrated with coarse sediments than deep ?ows laden with low concentrations of ?ne sediments. It is concluded that channel constriction can, but may not necessarily, lead to competence reversal, depending on channel geometry, ?ow discharge and sediment properties. Copyright © 2003 John Wiley & Sons, Ltd. 相似文献
17.
Eroded sediment may have significant effects on the hydraulics of overland flow, but few studies have been performed to quantify these effects on steep slopes. This study investigated the potential effects of sediment load on Reynolds number, Froude number, flow depth, mean velocity, Darcy–Weisbach friction coefficient, shear stress, stream power, and unit stream power of overland flow in a sand‐glued hydraulic flume under a wide range of hydraulic conditions and sediment loads. Slope gradients were varied from 8·7 to 34·2%, unit flow rates from 0·66 to 5·26×10?3 m2 s?1, and sediment loads from 0 to 6·95 kg m?1 s?1. Both Reynolds number (Re) and Froude number (Fr) decreased as sediment load increased, implying a decrease in flow turbulence. This inverse relationship should be considered in modeling soil erosion processes. Flow depth increased as sediment load increased with a mean value of 1·227 mm, caused by an increase in volume of sediment‐laden flow (contribution 62·4%) and a decrease in mean flow velocity (contribution 37·6%). The mean flow velocity decreased by up to 0·071 m s?1 as sediment load increased. The Darcy–Weisbach friction coefficient (f) increased with sediment load, showing that the total energy consumption increased with sediment load. The effects of sediment load on f depended on flow discharge: as flow discharge increased, the influence of sediment load on f decreased due to increased flow depth and reduced relative roughness. Flow shear stress and stream power increased with sediment load, on average, by 80·5% and 60·2%, respectively; however, unit stream power decreased by an average of 11·1% as sediment load increased. Further studies are needed to extend and apply the insights obtained under these controlled conditions to real‐world overland flow conditions. Copyright © 2010 John Wiley & Sons, Ltd. 相似文献
18.
Wind tunnel tests were conducted to examine the fetch effect of a gravel surface on the ?ux pro?le of the sand cloud blowing over it using typical dune sand. The results suggest that the ?ux pro?le of blown sand over a gravel surface differs from that over a sandy surface and is characterized by a peak ?ux at a height above the surface while that over a sandy surface decreases exponentially with height. The ?ux pro?le of a sand cloud over a gravel surface can be expressed by a Gaussian peak function: q = a + b exp (?0·5((h ? c)/d)2), where q is the sand transport rate at height h, and a, b, c and d are regression coef?cients. The signi?cance of the coef?cients in the function could be de?ned in accordance with the fetch length of the gravel surface and wind velocity. Coef?cient c represents the peak ?ux height and increases with both wind velocity and fetch length, implying that the peak ?ux height is related to the bounce height of the particles in the blowing sand cloud. Coef?cient d shows a tendency to increase with both wind velocity and fetch length. The sum of a and b, representing the peak ?ux, increases with wind velocity but decreases with fetch length. The average saltation height derived from the cumulative percentage curve shows a tendency to increase with both the fetch length and wind velocity. For any fetch length of a gravel surface the sand transport equation is expressed as Q = C(1 ? Ut/U)(ρ/g)U3, where Q is the sand transport rate, U is the wind velocity, Ut is the threshold velocity measured at the same height as U, g is the gravitational acceleration, ρ is the air density, C is a proportionality coef?cient that decreases with the fetch length of the gravel surface. At a given wind velocity, the sand transport rate over a gravel surface is only 52–68 per cent of that over a sandy surface. The ?ux rate in true creep over a gravel surface increases with wind velocity but decreases with the fetch length, whereas the creep proportion (the ratio of creep ?ux to the sand transport rate) decreases with both the wind velocity and fetch length. Two‐variable (including fetch length and wind velocity) equations were developed to predict the peak ?ux height, average saltation height and transport rate. Copyright © 2004 John Wiley & Sons, Ltd. 相似文献
19.
The estimation of debris‐?ow magnitude is an essential step in the assessment of debris‐?ow hazard. Although different methods have been developed for the assessment of debris‐?ow magnitude, this is still a dif?cult task because of the complexity of ?ow processes and the lack of data to test estimation procedures in many mountainous regions. Data on debris‐?ow magnitude from 127 basins in the Eastern Italian Alps have been collected from scienti?c and technical journals, technical reports, historical documents gathered from local archives, and ?eld surveys. These data were used to develop and test different predictive approaches, encompassing regression equations, geomorphological surveys and probabilistic analysis of time series. Regression techniques were used to correlate debris‐?ow magnitude to morphometric parameters and geological characteristics of the basins. Values of the channel debris yield rate (contribution per unit length of channel), proposed in the literature, were compared with data from the study area for identifying reference values for channel stretches of different morphological characteristics. Although limited to the few basins in which suf?cient data were available, the probabilistic analysis of time series of debris‐?ow magnitude provides indications about the relations between magnitude and frequency of debris ?ows. Some observations about the capability and drawbacks of considered methods are presented and the combined use of different approaches for the estimation of debris‐?ow magnitude is suggested. Copyright © 2004 John Wiley & Sons, Ltd. 相似文献
20.
Impacts of sediment load on Manning coefficient in supercritical shallow flow on steep slopes 总被引:1,自引:0,他引:1
The Manning equation is one of the most widely used formulae for calculating the velocity of shallow overland flow in hydrological and erosion models. Precise estimation of the Manning's friction coefficient (n) is critical to determining overland flow and soil erosion processes. Few studies have been conducted to quantify the effects of sediment load on Manning's n on steep slopes. This study was conducted to investigate the potential effects of sediment load on Manning's n in a flume with a fixed bed, under wide ranges of hydraulics and sediment loads. Slope gradient varied from 8·7 to 34·2%, unit flow rate from 0·66 to 5·26 × 10?3 m2 s?1, and sediment load from 0 to 6·95 kg m?1 s?1. The Reynolds number ranged from 350 to 5899. Results showed that Manning's n varied in both sediment‐free and sediment‐laden flows ranging from 0·012 to 0·055. The apparent Manning's coefficients of sediment‐laden flow were much greater than those of sediment‐free flow. The mean Manning coefficient of sediment‐laden flow was 51·27% greater than the mean value of sediment‐free flow. For sediment‐laden flow, Manning's n could be estimated with a power function of unit flow discharge and sediment content. Further studies are needed to quantify the potential effects of sediment load on the Manning's n on erodible beds and in fields. Copyright © 2010 John Wiley & Sons, Ltd. 相似文献