Preliminary seismic microzonation of Sivas city (Turkey) using microtremor and refraction microtremor (ReMi) measurements

Sivas city, located in the inner east part of Anatolia (Turkey), is far from seismic sources. However, the city is under risk owing to strong earthquakes occurring around the area, and different soil conditions that can produce variation in the ground motion amplification. Microzonation of cities provides a basis for site-specific hazard analysis in urban settlements. In particular, seismic microzonation can be achieved by means of detailed seismic assessment of the area, including earthquake recordings and geological studies. In this paper, we propose a preliminary microzonation map for the city of Sivas, based on the variation in the dominant periods of the sediments covering the area. The periods are retrieved from microtremor measurements conducted at 114 sites, using the horizontal-to-vertical spectral ratio technique. The results of microtremor analysis were compared with those obtained from refraction microtremor measurements at two profiles crossing the studied area. According to the classification of dominant periods, Sivas area can be divided into four zones, probably prone to different levels of seismic hazard. However, specific studies including analysis of weak earthquakes are required in the future to validate our microzonation map.     

Comparison between different techniques for evaluation of predominant periods using strong ground motion records and microtremors in Pereira Colombia

This paper presents a comparison between different techniques for evaluation of predominant periods in soft soil, for the urban area of Pereira city, Western Colombia. In this study we used microtremor and strong ground motion records obtained by a local array of seven accelerographs stations deployed in the city. Response spectra and spectral ratios have been calculated and compared with strong seismic events recorded in solid rock and soft soil stations. These observations allowed the determination of dominant response spectra for several sectors in the urban area. For the microtremor measurements and earthquake data, dominant periods were determined using interpretation of Fourier amplitude spectra and Nakamura's technique. A comparison between dominant periods obtained from strong ground motion records and those obtained from microtremor measurements show similarities, which is in the range 0.2–0.5 s. A preliminary version of a site response map for Pereira city was obtained from this analysis.     

武汉市主城规划区地震动参数小区划及其应用问题研究

本文以武汉市主城规划区地震动参数小区划（以下简称武汉市地震动参数小区划）工作为主线,研究了弱震区内潜在震源区划分和工程地质条件对峰值加速度的影响程度、软土地基反应谱特征与构造措施的选取,以及以小区划成果作为抗震设防标准在实际应用中所遇到的一些问题。     

Seismic Observations and Seismic Hazard Studies in the Philippines

It has taken more than a hundred years for seismic observations in the Philippines to evolve to a modern observation system.The responsibility of seismic observations was likewise transfeered from one agency to another during this same period of time.At present,the mandate of conducting seismic observatins in the Philippines rests with the Philippine Institute of Volcanology and Seismology(PHIVOLCS),In 2000,through a grant aid from the Japan International Cooperation Agency(JICA),the Philippine Seismic netowrk was upgraded to a digital system.As a result,a new set of seismic monitoring equipments was installed in all of the 34 PHIVOLCS seismic stations all over the country,Digital waveforms are now available for high level seismic data processing.and data acquisition and processing are now automated.Included in the upgrade is the provision of strong motion accelerographs in all stations whose data can now be used for studying ground motion and intensity attenuation relations,The new setup is now producing high-resolution data that can now be used for conducting basic seismological researches,Earthquake locations have now improved allowing for the modeling and delineation of earthquake source regions necessary for earthquake hazard studies.Current seismic hazard studies in the Philippines involve the estimation of ground motion using both probabilitstic and deterministic approaches,seismic microzonation studies of key cities using microtremor observations,paleoseismology and active faults mapping ,and identification of liquefaction-prone,landslide-prone nd tsunami-affected areas.The earthquake database is now being reviewed and completed with the addition of historical events and from data from regional databases,While studies of seismic hazards were primarily concentrated on a regional level ,PHIVOLCS is now focusing on doing these seismic hazard studies on a micriolevel.For Metro Manila,first generation hazard maps showing ground rupture,ground shaking and liquefaction hazards have recently been completed.Other large cities that are also at risk from large earthquakes are the next targets.The elements at risk such as population,lifelines,and vertical and horizontal structures for each of these urban centers are also being incorporated in the hazard maps for immediate use of planners,civil defense officials,policy-makers and engineers.The maps can also now be used to describe possible scenarios during times of strong events and how appropriate socio-economic and engineering responses could be designed.In addition,a rapid earthquake damage assessment system has been started which will attempt to produce immediate or rapid assessments identification of elements at risk durin times of strong earthquakes     

Regional and local seismic hazard assessment

Recent earthquakes such as the M_JMA 7.2 Hyogo-ken Nambu earthquake and the M 7.4 Kocaeli earthquake demonstrate once again the need to include detailed soil investigation into hazard evaluation, that is the need of microzonation. Seismic hazard assessment evaluated at a regional scale generally does not consider soil effects but only in a limited way using an attenuation law that can be ‘soft soil’ or ‘rock’. However, the relevant role of seismic hazard in the assessment of seismic coefficients for the definition of the actions in seismic codes must be properly considered. That is to say, the level of protection of buildings is proportional to a definite level of hazard (generally considered to be the ground motion with 10% probability of exceedence in 50 years). When a microzonation is performed, this criterion cannot be ignored, therefore, a clear linkage must be established between hazard (regional scale) and microzonation. The crucial point is represented by the reference motion (or input motion) to be used for site effects analysis, that must be compatible with the regional seismic hazard. In this paper, three different approaches for reference motion evaluation are analysed: probabilistic; stochastic; and deterministic. Through the case history of Fabriano microzonation the three approaches are compared. It is shown that each approach presents advantages and disadvantages with respect to the others. For example, the probabilistic approach (the reference motion is directly derived from the expected response spectra for a given return period) is linked with hazard, but produces an overestimation in short periods range, while the deterministic approach correctly simulates the wave propagation, but it ends with a kind of conditional probability. Until now, clear criteria to choose the right approach do not appear to exist and the expert experience is of fundamental importance.     

Probabilistic seismic hazard assessment for Thailand

A set of probabilistic seismic hazard maps for Thailand has been derived using procedures developed for the latest US National Seismic Hazard Maps. In contrast to earlier hazard maps for this region, which are mostly computed using seismic source zone delineations, the presented maps are based on the combination of smoothed gridded seismicity, crustal-fault, and subduction source models. Thailand’s composite earthquake catalogue is revisited and expanded, covering a study area limited by 0°–30°N Latitude and 88°–110°E Longitude and the instrumental period from 1912 to 2007. The long-term slip rates and estimates of earthquake size from paleoseismological studies are incorporated through a crustal fault source model. Furthermore, the subduction source model is used to model the megathrust Sunda subduction zones, with variable characteristics along the strike of the faults. Epistemic uncertainty is taken into consideration by the logic tree framework incorporating basic quantities, such as different source modelling, maximum cut-off magnitudes and ground motion prediction equations. The ground motion hazard map is presented over a 10 km grid in terms of peak ground acceleration and spectral acceleration at 0.2, 1.0, and 2.0 undamped natural periods and a 5% critical damping ratio for 10 and 2% probabilities of exceedance in 50 years. The presented maps give expected ground motions that are based on more extensive data sources than applied in the development of previous maps. The main findings are that northern and western Thailand are subjected to the highest hazard. The largest contributors to short- and long-period ground motion hazard in the Bangkok region are from the nearby active faults and Sunda subduction zones, respectively.     

Multi scenario seismic hazard assessment for Egypt

Egypt is located in the northeastern corner of Africa within a sensitive seismotectonic location. Earthquakes are concentrated along the active tectonic boundaries of African, Eurasian, and Arabian plates. The study area is characterized by northward increasing sediment thickness leading to more damage to structures in the north due to multiple reflections of seismic waves. Unfortunately, man-made constructions in Egypt were not designed to resist earthquake ground motions. So, it is important to evaluate the seismic hazard to reduce social and economic losses and preserve lives. The probabilistic seismic hazard assessment is used to evaluate the hazard using alternative seismotectonic models within a logic tree framework. Alternate seismotectonic models, magnitude-frequency relations, and various indigenous attenuation relationships were amended within a logic tree formulation to compute and develop the regional exposure on a set of hazard maps. Hazard contour maps are constructed for peak ground acceleration as well as 0.1-, 0.2-, 0.5-, 1-, and 2-s spectral periods for 100 and 475 years return periods for ground motion on rock. The results illustrate that Egypt is characterized by very low to high seismic activity grading from the west to the eastern part of the country. The uniform hazard spectra are estimated at some important cities distributed allover Egypt. The deaggregation of seismic hazard is estimated at some cities to identify the scenario events that contribute to a selected seismic hazard level. The results of this study can be used in seismic microzonation, risk mitigation, and earthquake engineering purposes.     

Seismic Zonation of the Delhi Region for Bedrock Ground Motion

An endeavor is made to compute peak ground horizontal accelerations at bedrock level in the Delhi region due to the seismogenic sources present around Delhi. The entire area is divided into six seismogenic sources for which seismic hazard analysis is carried out using the complete and extreme part of the seismicity data. Maximum likelihood estimates of hazard parameters viz., seismic activity rate , b value and maximum probable earthquake M _max are made for each zone. The return periods and the probabilities of occurrence of various magnitudes for return periods of 50, 100 and 1000 years are also computed for each zone. The peak ground acceleration (PGA) values for 20% exceedance in 50 years are then computed for the Delhi region from each zone. The maximum PGA value considering all the zones is 0.34 g, which is due to the Mathura fault zone. The seismogenic zones V and VI, i.e., Mathura fault zone and the Sohna fault zone are observed to be contributing maximum PGA values in the Delhi region governing the isoacceleration contours computed for the region. The seismic zonation map for the PGA values at the bedrock level is obtained for the Delhi region. This can be used directly as input for the microzonation of ground motion at the surface by incorporating the local site conditions.     

Seismic ground amplification by unlined tunnels subjected to vertically propagating SV and P waves using BEM

Recent researches have revealed that the seismic ground response above tunnels can be different from the free-field motion during earthquakes. Nevertheless, to the best of the authors׳ knowledge, neither building codes nor seismic microzonation guidelines have yet considered this matter. In the present study, the seismic response of a linear elastic medium including a buried unlined tunnel subjected to vertically propagating incident SV and P waves are addressed. For analysis purposes, a numerical time-domain analysis is performed by utilizing a robust numerical algorithm working based on the boundary element method. It is observed that the amplification of the ground surface underlain by a tunnel is increased in long periods. The variation of the amplification factor and characteristic period of the medium versus the buried depth of the tunnel are depicted as the major results of this study. Some simple and useful relations are proposed for estimating the seismic microzonation of the areas underlain by tunnels. These relations can also be used for the preliminary seismic design of structures located on underground structures.     

TBT-pollution in the Gulf of Thailand: A re-inspection of imposex incidence after 10 years

Imposex in neogastropods was used to determine the relative TBT distribution in the Gulf of Thailand in 2006. To identify the imposex prevalence, 8757 specimens, belonging to 22 species from five families of neogastropods, were collected at 56 sites in 13 sample areas. These areas were located between the Bight of Bangkok in the north and the Malaysian border in the south. A contamination model was developed to compensate for differences in TBT sensitivity among species and to make comparisons among areas. At every area imposex was found in neogastropods. The highest incidence was in the east side of the Bight of Bangkok off Si Racha and Pattaya and in the southern part around Pattani. The same areas showed the highest frequency of imposex in 1996. While the frequency of imposex appeared to have slightly decreased in these areas, increases were found elsewhere. In Pattani Province this could be related to dumping of highly polluted harbour sediments in the shallow coastal area. The overall frequency of imposex in the Gulf of Thailand significantly increased from 1996 to 2006.     

应用微动H/V谱比法和台阵技术探测场地响应和浅层速度结构

为了快速而且廉价地获取北京市详细的场地响应和浅层速度结构,应用于地震动模拟和地震灾害预防,我们开展了微动观测技术和处理方法研究.本文利用2007年夏季北京五棵松地区进行的几个微动观测实验数据,使用单台H/V谱比法分析场地的卓越频率及其对应的放大系数,并对比了不同地震仪和观测时间对H/V曲线的影响;应用高分辨率F-K频谱分析方法从微动台阵数据中得到Rayleigh波的频散曲线并使用邻域算法反演出浅层速度结构.H/V结果表明该地区卓越频率在2.1～2.2 Hz之间,对应的放大系数下限约为3;利用微动H/V方法得到的场地卓越频率具有较高的稳定性.微动台阵反演结果给出了比较合理的波阻抗界面深度和层平均速度结构,认为地下80多米处的波阻抗界面是决定场地卓越频率和其场地放大系数的主要界面.本研究表明微动技术应用于评估城市地震场地响应和浅层速度结构是可行且易于实施的.     

Seismic microzonation of Marsa Alam, Egypt using inversion HVSR of microtremor observations

An attempt was made to estimate seismic microzonation in Marsa Alam city, Egypt based on the analysis of seismic microtremor observations. Observations were carried out at 140 sites in the study region. Analysis and processing of microtremor were divided into two steps; the first one is to measure the horizontal-to-vertical spectral ratios (HVSR) for each site and picked predominant frequency and its amplitude for each site. The second step is to measure the average shear wave velocity in the upper 30 m (Vs30) of subsoil using inversion of HVSR technique. The results show well matching of theoretical HVSR and observed HVSR for body waves in all sites. The Vs30 parameter was used to classify subsoil into classes of soil properties converted to the slandered European soil code (Eurocode-8 (2002)) as follows; Vs < 180(class D), 180 ≤ Vs < 360 (class C), 360 ≤ Vs < 800 (class B) and Vs ≥ 800 m/s (class A). Our study exhibits that most of Marsa Alam city were covered by B and C classes with small portions of class D close to the shoreline and class A at the northeastern part of the region. The developed classification soil map of the study area was correlated with the distribution of the predominant frequency in view of the surface geology and given a good matching. The results of this study will be useful for planning the Marsa Alam region to be the future tourist dream for Egypt. The method used in assessment of seismic microzonation in Marsa Alam city could be the fast and inexpensive technique to measure the Vs30 based on the HVSR of microtremor and would be applied in many other areas in Egypt.     

Ground‐motion attenuation relationship for the Sumatran megathrust earthquakes

A representative attenuation relationship is one of the key components required in seismic hazard assessment of a region of interest. Attenuation relationships for peak ground acceleration, peak ground velocity and response spectral accelerations for Sumatran megathrust earthquakes, covering M_w up to 9.0, are derived based on synthetic seismograms obtained from a finite‐fault kinematic model. The relationships derived are for very hard rock site condition and for a long‐distance range between 200 and 1500 km. They are then validated with recorded data from giant earthquakes on the Sumatran megathrust occurring since year 2000. A close examination of the recorded data also shows that spectral shapes predicted by most of the existing attenuation relationships and that specified in the IBC code are not particularly suitable for sites where potential seismic hazard is dominated by large‐magnitude, distant, earthquakes. Ground motions at a remote site are typically signified by the dominance of long‐period components with periods longer than 1 s, whereas the predominant periods from most of the existing attenuation relationships and the IBC code are shorter than 0.6 s. The shifting of response spectrum towards longer period range for distant earthquakes should be carefully taken into account in the formulation of future seismic codes for Southeast Asia, where many metropolises are located far from active seismic sources. The attenuation relationship derived in the present study can properly reproduce the spectral shape from distant subduction earthquakes, and could hopefully give insights into the formulation of future seismic codes. Copyright © 2009 John Wiley & Sons, Ltd.     

Analysis of the weightiness of site effects on reinforced concrete (RC) building seismic behaviour: The Adra town example (SE Spain)

The damage distribution in Adra town (south‐eastern Spain) during the 1993 and 1994 Adra earthquakes (5.0 magnitude), that reached a maximum intensity degree of VII (European Macroseismic Scale (EMS scale)), was concentrated mainly in the south‐east zone of the town and the most relevant damage occurred in reinforced concrete (RC) buildings with four or five storeys. In order to evaluate the influence of ground condition on RC building behaviour, geological, geomorphological and geophysical surveys were carried out, and a detailed map of ground surface structure was obtained. Short‐period microtremor observations were performed in 160 sites on a 100m × 100m dimension grid and Nakamura's method was applied in order to determine a distribution map of soil predominant periods. Shorter predominant periods (0.1–0.3 s) were found in mountainous and neighbouring zones and larger periods (greater than 0.5 s) in thicker Holocene alluvial fans. A relationship T = (0.049 ± 0.001)N, where T is the natural period of swaying motion and N is the number of storeys, has been empirically obtained by using microtremor measurements at the top of 38 RC buildings (ranging from 2 to 9 storeys). 1‐D simulation of strong motion on different soil conditions and for several typical RC buildings were computed, using the acceleration record in Adra town of the 1993 earthquake. It is noteworthy that all the aforementioned results show the influence of site effects in the degree and distribution of observed building damage. Copyright © 2007 John Wiley & Sons, Ltd.     

Soil characterization for seismic damage scenarios purposes: application to Angra do Heroísmo (Azores)

Angra do Heroismo, the main town of Terceira Island in the Azores Archipelago, was hit in 1980 by a 7.2 magnitude earthquake that caused great destruction in the central part of the town. Taking into consideration the high seismic hazard of the region and the cultural and social importance of Angra do Heroísmo, the elaboration of damage scenarios is of particular importance to implement measures for preserve and protect the town against future earthquakes. The first step is to perform microzonation studies in order to characterize the soil seismic behaviour. Taking into consideration the available geologic, geotechnical and geophysical information, a detailed soil characterization was performed based on the results from numerical modelling and the analysis of microtremor experimental measurements. Nine different soil profiles were identified, characterized and classified. Discussion on the detailed soil classification and the Eurocode 8 soil classification is presented. This study shows that even with an available code, microzonation studies must be developed in order to identify differences on soil behaviour inside the interested area. It shows also that the use of experimental measurements presents a great help on soil characterization. The obtained detailed classification will be used on the estimation of damage scenarios for Angra do Heroísmo.     

Assessment of <Emphasis Type="Italic">pre-crisis</Emphasis> and <Emphasis Type="Italic">syn-crisis</Emphasis> seismic hazard at Campi Flegrei and Mt. Vesuvius volcanoes,Campania, southern Italy

In this study, we address the issue of short-term to medium-term probabilistic seismic hazard analysis for two volcanic areas, Campi Flegrei caldera and Mt. Vesuvius in the Campania region of southern Italy. Two different phases of the volcanic activity are considered. The first, which we term the pre-crisis phase, concerns the present quiescent state of the volcanoes that is characterized by low-to-moderate seismicity. The second phase, syn-crisis, concerns the unrest phase that can potentially lead to eruption. For the Campi Flegrei case study, we analyzed the pattern of seismicity during the 1982–1984 ground uplift episode (bradyseism). For Mt. Vesuvius, two different time-evolutionary models for seismicity were adopted, corresponding to different ways in which the volcano might erupt. We performed a site-specific analysis, linked with the hazard map, to investigate the effects of input parameters, in terms of source geometry, mean activity rate, periods of data collection, and return periods, for the syn-crisis phase. The analysis in the present study of the pre-crisis phase allowed a comparison of the results of probabilistic seismic hazard analysis for the two study areas with those provided in the Italian national hazard map. For the Mt. Vesuvius area in particular, the results show that the hazard can be greater than that reported in the national hazard map when information at a local scale is used. For the syn-crisis phase, the main result is that the data recorded during the early months of the unrest phase are substantially representative of the seismic hazard during the whole duration of the crisis.     

Microtremor Measurements for the Microzonation of Dinar

v--vThe geotechnical site conditions in Dinar town located in western Turkey were investigated after the 1995 Dinar earthquake based on borings, in situ penetration tests, seismic wave velocity measurements, and microtremor records. The variation of damage distribution within the town was evaluated with respect to 23 district damage ratios calculated, based on the detailed damage survey conducted by the General Directorate of Disaster Affairs. Site amplifications were estimated from microtremor spectral ratios and microzonation was performed using a GIS methodology. The results of in situ penetration tests and seismic wave velocity measurements as well as the damage distribution were compared with the amplification zonation obtained from microtremor records. The results indicate the applicability of microtremor spectral ratios for assessing the local site conditions and site amplifications.     

Seismic microzonation and earthquake damage scenarios for urban areas

A methodology for seismic microzonation and earthquake damage scenarios may be considered as composed of two stages. In the first stage, microzonation maps with respect to estimated earthquake characteristics on the ground surface are generated for an investigated urban area. The effects of local geological and geotechnical site conditions are taken into account based on site characterization with respect to representative soil profiles extending down to the engineering bedrock. 1D site response analyses are performed to calculate earthquake characteristics on the ground surface using as many as possible, hazard compatible real acceleration time histories. In the second stage, vulnerability of buildings and pipeline systems are estimated based on site-specific ground motion parameters. A pilot study is carried out to evaluate seismic damage in a district in Istanbul, Turkey. The results demonstrate the significance of site characterization and site response analysis in calculating the earthquake characteristics on the ground surface in comparison to simplified empirical procedures.     

Ambient noise as the new source for urban engineering seismology and earthquake engineering: a case study from Beijing metropolitan area

In highly populated urban centers, traditional seismic survey sources can no longer be properly applied due to restrictions in modern civilian life styles. The ambient vibration noise, including both microseisms and microtremor, though are generally weak but available anywhere and anytime, can be an ideal supplementary source for conducting seismic surveys for engineering seismology and earthquake engineering. This is fundamentally supported by advanced digital signal processing techniques for effectively extracting the useful information out from the noise. Thus, it can be essentially regarded as a passive seismic method. In this paper we first make a brief survey of the ambient vibration noise, followed by a quick summary of digital signal processing for passive seismic surveys. Then the applications of ambient noise in engineering seismology and earthquake engineering for urban settings are illustrated with examples from Beijing metropolitan area. For engineering seismology the example is the assessment of site effect in a large area via microtremor observations. For earthquake engineering the example is for structural characterization of a typical reinforced concrete high-rise building using background vibration noise. By showing these examples we argue that the ambient noise can be treated as a new source that is economical, practical, and particularly valuable to engineering seismology and earthquake engineering projects for seismic hazard mitigation in urban areas.