Combining a Detailed Building Energy Model with a Physically-Based Urban Canopy Model

A scheme that couples a detailed building energy model, EnergyPlus, and an urban canopy model, the Town Energy Balance (TEB), is presented. Both models are well accepted and evaluated within their individual scientific communities. The coupled scheme proposes a more realistic representation of buildings and heating, ventilation and air-conditioning (HVAC) systems, which allows a broader analysis of the two-way interactions between the energy performance of buildings and the urban climate around the buildings. The scheme can be used to evaluate the building energy models that are being developed within the urban climate community. In this study, the coupled scheme is evaluated using measurements conducted over the dense urban centre of Toulouse, France. The comparison includes electricity and natural gas energy consumption of buildings, building façade temperatures, and urban canyon air temperatures. The coupled scheme is then used to analyze the effect of different building and HVAC system configurations on building energy consumption, waste heat released from HVAC systems, and outdoor air temperatures for the case study of Toulouse. Three different energy efficiency strategies are analyzed: shading devices, economizers, and heat recovery.     

An Improved Three-Dimensional Simulation of the Diurnally Varying Street-Canyon Flow

The impact of diurnal variations of the heat fluxes from building and ground surfaces on the fluid flow and air temperature distribution in street canyons is numerically investigated using the PArallelized Large-eddy Simulation Model (PALM). Simulations are performed for a 3 by 5 array of buildings with canyon aspect ratio of one for two clear summer days that differ in atmospheric instability. A detailed building energy model with a three-dimensional raster-type geometry—Temperature of Urban Facets Indoor-Outdoor Building Energy Simulator (TUF-IOBES)—provides urban surface heat fluxes as thermal boundary conditions for PALM. In vertical cross-sections at the centre of the spanwise canyon the mechanical forcing and the horizontal streamwise thermal forcing at roof level outweigh the thermal forces from the heated surfaces inside the canyon in defining the general flow pattern throughout the day. This results in a dominant canyon vortex with a persistent speed, centered at a constant height. Compared to neutral simulations, non-uniform heating of the urban canyon surfaces significantly modifies the pressure field and turbulence statistics in street canyons. Strong horizontal pressure gradients were detected in streamwise and spanwise canyons throughout the day, and which motivate larger turbulent velocity fluctuations in the horizontal directions rather than in the vertical direction. Canyon-averaged turbulent kinetic energy in all non-neutral simulations exhibits a diurnal cycle following the insolation on the ground in both spanwise and streamwise canyons, and it is larger when the canopy bottom surface is paved with darker materials and the ground surface temperature is higher as a result. Compared to uniformly distributed thermal forcing on urban surfaces, the present analysis shows that realistic non-uniform thermal forcing can result in complex local airflow patterns, as evident, for example, from the location of the vortices in horizontal planes in the spanwise canyon. This study shows the importance of three-dimensional simulations with detailed thermal boundary conditions to explore the heat and mass transport in an urban area.     

A Double-Canyon Radiation Scheme for Multi-Layer Urban Canopy Models

We develop a double-canyon radiation scheme (DCEP) for urban canopy models embedded in mesoscale numerical models based on the Building Effect Parametrization (BEP). The new scheme calculates the incoming and outgoing longwave and shortwave radiation for roof, wall and ground surfaces for an urban street canyon characterized by its street and building width, canyon length, and the building height distribution. The scheme introduces the radiative interaction of two neighbouring urban canyons allowing the full inclusion of roofs into the radiation exchange both inside the canyon and with the sky. In contrast to BEP, we also treat direct and diffuse shortwave radiation from the sky independently, thus allowing calculation of the effective parameters representing the urban diffuse and direct shortwave radiation budget inside the mesoscale model. Furthermore, we close the energy balance of incoming longwave and diffuse shortwave radiation from the sky, so that the new scheme is physically more consistent than the BEP scheme. Sensitivity tests show that these modifications are important for urban regions with a large variety of building heights. The evaluation against data from the Basel Urban Boundary Layer Experiment indicates a good performance of the DCEP when coupled with the regional weather and climate model COSMO-CLM.     

Effects of Unstable Thermal Stratification on Vertical Fluxes of Heat and Momentum in Urban Areas

A Reynolds-averaged Navier–Stokes microscale model is used for the simulation of the effect of unstable thermal stratification on the flow within an aligned configuration of building-like cubes as used in Santiago et al. (Urban Clim 9:115–133, 2014). The spatially-averaged results show increased dispersive fluxes, turbulent length scales and sectional drag coefficient. An extension of K-theory is presented to parametrize the sum of the turbulent and dispersive fluxes, and the length scale and drag coefficient increases are parametrized as functions of the ratio of buoyant and inertial forces. This approach improves the results of urban canopy parametrization simulations inside and above the urban canyon and represents the first attempt to account for the dispersive fluxes and the effect of solar radiation on the flow.     

一种单层城市冠层模式的建立及数值试验研究

本文在引进先进的城市地表能量平衡方案 (Town Energy Balance, 简称TEB) 的基础上建立了一个单层城市冠层模式, 并对南京市典型居民区1 km2范围内的局地尺度地表能量平衡各分量进行离线模拟, 将模拟结果与同期观测值作了比对, 发现: TEB方案对城市地表能量平衡各分量的模拟效果良好, 而该方案的模拟性能受建筑物表面材料反照率取值的影响较大。在离线研究的基础上, 本文又将TEB方案成功耦合到南京大学区域边界层模式 (NJU－RBLM) 中, 作为该模式的地表能量平衡参数化方案之一, 分别选取该边界层模式中原有的地表能量平衡参数化方案SVAT (Soil－Vegetation－Atmosphere－Transfer model) 和新引入的TEB方案对冬夏两季不同个例进行模拟, 以常规近地面气温观测资料和Landsat卫星观测的地表反照率资料对模拟结果进行比较, 结果表明: TEB方案对原大气边界层模式的模拟效果有明显改善, 对近地面热力场的改善效果尤为明显, 可以很好地模拟出城市冠层中的“陷阱效应”。     

A Vegetated Urban Canopy Model for Meteorological and Environmental Modelling

An urban canopy model is developed for use in mesoscale meteorological and environmental modelling. The urban geometry is composed of simple homogeneous buildings characterized by the canyon aspect ratio (h/w) as well as the canyon vegetation characterized by the leaf aspect ratio (σ _l ) and leaf area density profile. Five energy exchanging surfaces (roof, wall, road, leaf, soil) are considered in the model, and energy conservation relations are applied to each component. In addition, the temperature and specific humidity of canopy air are predicted without the assumption of thermal equilibrium. For radiative transfer within the canyon, multiple reflections for shortwave radiation and one reflection for longwave radiation are considered, while the shadowing and absorption of radiation due to the canyon vegetation are computed by using the transmissivity and the leaf area density profile function. The model is evaluated using field measurements in Vancouver, British Columbia and Marseille, France. Results show that the model quite well simulates the observations of surface temperatures, canopy air temperature and specific humidity, momentum flux, net radiation, and energy partitioning into turbulent fluxes and storage heat flux. Sensitivity tests show that the canyon vegetation has a large influence not only on surface temperatures but also on the partitioning of sensible and latent heat fluxes. In addition, the surface energy balance can be affected by soil moisture content and leaf area index as well as the fraction of vegetation. These results suggest that a proper parameterization of the canyon vegetation is prerequisite for urban modelling.     

Dispersion of a Passive Scalar Within and Above an Urban Street Network

The transport of a passive scalar from a continuous point-source release in an urban street network is studied using direct numerical simulation (DNS). Dispersion through the network is characterized by evaluating horizontal fluxes of scalar within and above the urban canopy and vertical exchange fluxes through the canopy top. The relative magnitude and balance of these fluxes are used to distinguish three different regions relative to the source location: a near-field region, a transition region and a far-field region. The partitioning of each of these fluxes into mean and turbulent parts is computed. It is shown that within the canopy the horizontal turbulent flux in the street network is small, whereas above the canopy it comprises a significant fraction of the total flux. Vertical fluxes through the canopy top are predominantly turbulent. The mean and turbulent fluxes are respectively parametrized in terms of an advection velocity and a detrainment velocity and the parametrization incorporated into a simple box-network model. The model treats the coupled dispersion problem within and above the street network in a unified way and predictions of mean concentrations compare well with the DNS data. This demonstrates the usefulness of the box-network approach for process studies and interpretation of results from more detailed numerical simulations.     

Further Development of the Vegetated Urban Canopy Model Including a Grass-Covered Surface Parametrization and Photosynthesis Effects

The vegetated urban canopy model (VUCM), which includes parametrizations of urban physical processes for artificial surfaces and vegetated areas in an integrated system, has been further developed by including physical processes associated with grass-covered surfaces in urban pervious surfaces and the photosynthesis effects of urban vegetation. Using measurements made from three urban/suburban sites during the BUBBLE field campaign in 2002, the model’s performance in modelling surface fluxes (momentum flux, net radiation, sensible and latent heat fluxes and storage heat flux) and canopy air conditions (canopy air temperature and specific humidity) was critically evaluated for the non-precipitation and the precipitation days. The observed surface fluxes at the urban/suburban sites were significantly altered by precipitation as well as urban vegetation. Especially, the storage heat at urban surfaces and underlying substrates varied drastically depending on weather conditions while having an important role in the formation of a nocturnal urban surface layer. Unlike the nighttime canopy air temperature that was largely affected by the storage-heat release, the daytime canopy air conditions were highly influenced by the vertical turbulent exchange with the overlying atmosphere. The VUCM well reproduced these observed features in surface fluxes and canopy air conditions at all sites while performing well for both the non-precipitation and the precipitation days. The newly implemented parametrizations clearly improved the model’s performance in the simulation of sensible and latent heat fluxes at the sites, more noticeably at the suburban site where the vegetated area fraction is the largest among the sites. Sensitivity analyses for model input parameters in VUCM elucidated the relative importance of the morphological, aerodynamic, hydrological and radiative/thermal properties in modelling urban surface fluxes and canopy air conditions for daytime and nighttime periods. These results suggest that the VUCM has great potential for urban atmospheric numerical modelling for a range of cities and weather conditions in addition to having a better physical basis in the representation of urban vegetated areas and associated physical processes.     

A Backward-Lagrangian-Stochastic Footprint Model for the Urban Environment

Built terrains, with their complexity in morphology, high heterogeneity, and anthropogenic impact, impose substantial challenges in Earth-system modelling. In particular, estimation of the source areas and footprints of atmospheric measurements in cities requires realistic representation of the landscape characteristics and flow physics in urban areas, but has hitherto been heavily reliant on large-eddy simulations. In this study, we developed physical parametrization schemes for estimating urban footprints based on the backward-Lagrangian-stochastic algorithm, with the built environment represented by street canyons. The vertical profile of mean streamwise velocity is parametrized for the urban canopy and boundary layer. Flux footprints estimated by the proposed model show reasonable agreement with analytical predictions over flat surfaces without roughness elements, and with experimental observations over sparse plant canopies. Furthermore, comparisons of canyon flow and turbulence profiles and the subsequent footprints were made between the proposed model and large-eddy simulation data. The results suggest that the parametrized canyon wind and turbulence statistics, based on the simple similarity theory used, need to be further improved to yield more realistic urban footprint modelling.     

Modelling of the OASIS Energy Flux Measurements Using Two Canopy Concepts

Two land surface schemes, SCAM and CSIRO9, were used to model the measured energy fluxes during the OASIS (Observations At Several Interacting Scales) field program. The measurements were taken at six sites along a 100 km rainfall gradient. Two types of simulations were conducted: (1) offline simulations forced with measured atmospheric input data at each of the six sites, and (2) regional simulations with the two land surface schemes coupled to the regional climate model DARLAM.The two land surface schemes employ two different canopy modelling concepts: in SCAM the vegetation is conceptually above the ground surface, while CSIRO9 employs the more commonly used `horizontally tiled' approach in which the vegetation cover is modelled by conceptually placing it beside bare ground. Both schemes utilize the same below-ground components (soil hydrological and thermal models) to reduce the comparison to canopy processes only. However, the ground heat flux, soil evaporation and evapotranspiration are parameterised by the two canopy treatments somewhat differently.Both canopy concepts reproduce the measured energy fluxes. SCAM has a slightly higher root-mean standard error in the model-measurement comparison for the ground heat flux. The mean surface radiative temperature simulated by SCAM is approximately 1K lower than in the CSIRO9 simulations. However, the soil and vegetation temperatures (which contribute to the radiative temperature) varied more in the CSIRO9 simulations. These larger variations are due to the absence of a representation of the aerodynamic interactions between vegetation and ground.     

Towards a parametrization of river discharges into ocean general circulation models: a closure through energy conservation

Diagnostic methods are defined in order to compare two numerical simulations of ocean dynamics in a region of freshwater influence. The first one is a river plume simulation based on a high resolution numerical configuration of the POM coastal ocean model in which mixing parametrizations have been previously defined. The second one is a simulation based on the NEMO Global Ocean Model used for climate simulations in its half-a-degree configuration in which a river inflow is represented as precipitation on two coastal grid cells. Both simulations are forced with the same freshwater inflows and wind stresses. The divergence of volumetric fluxes above and below the halocline are compared. Results show that when an upwelling wind blows, the two models display similar behavior although the impact of lack of precision can be observed in the NEMO configuration. When a downwelling wind blows, the NEMO Global Ocean configuration can not reproduce the coastally trapped baroclinic dynamics because its grid resolution is too coarse. To find a parametrization to help represent these dynamics in ocean general circulation models, a method based on energy conservation is investigated. This method shows that it is possible to link the energy fluxes provided by river inflows to the divergence of energy fluxes integrated over the grid cells of ocean general circulation models. A parametrization of the dynamics created by freshwater inflows is deduced from this method. This enabled creation of a box model that proved to have the same behavior as the fluxes previously computed from the high resolution configuration.     

WRF/NCAR模拟的夏季长三角城市群区域多城市热岛和地表能量平衡

利用一个包含城市冠层效应的区域模式(WRF/NCAR),对长三角特大城市群的夏季气候效应进行了5 a(2003—2007年)高分辨数值模拟,通过长三角地区有无城市的对比试验分析,重点分析了城市群所造成的多城市热岛和地表能量平衡及其日变化特征。结果表明:城市化会导致显著的地表升温,但昼夜不同的升温幅度造成城市地表温度日较差的降低,以及部分郊区日较差增加;城市化也减小城市近地面风速,但沿海城市升温造成的热力差异,增大白天的海风并降低夜间的陆风。同时大范围城市群的热岛能够显著降低低层气压,导致部分海面风速持续的增加;城市下垫面具有很小的潜热通量,但感热通量和热存储量较大,白天的热岛逐渐增加,并在日落前达到最大,夜间热岛基本维持,但在日出前后迅速减弱;较大的入射短波辐射、较小的向下长波辐射和较低的10 m风速能够减弱白天的热岛,而增强夜间的热岛,并且使热岛峰值从17时延后至20时出现;反之亦然。     

A Physically-Based Scheme For The Urban Energy Budget In Atmospheric Models

An urban surface scheme for atmospheric mesoscale models ispresented. A generalization of local canyon geometry isdefined instead of the usual bare soil formulation currently usedto represent cities in atmospheric models. This allows refinement ofthe radiative budgets as well as momentum, turbulent heat and ground fluxes.The scheme is aimed to be as general as possible, in order to representany city in the world, for any time or weather condition(heat island cooling by night, urban wake, water evaporation after rainfalland snow effects).Two main parts of the scheme are validated against published data.Firstly, it is shown that the evolution of the model-predictedfluxes during a night with calm winds is satisfactory, considering both the longwave budget and the surface temperatures. Secondly, the original shortwave scheme is tested off-line and compared to the effective albedoof a canyon scale model. These two validations show that the radiative energy input to the urban surface model is realistic.Sensitivity tests of the model are performed for one-yearsimulation periods, for both oceanic and continental climates. The scheme has the ability to retrieve, without ad hoc assumptions, the diurnal hysteresis between the turbulent heat flux and ground heat flux. It reproduces the damping of the daytime turbulent heat flux by the heat storage flux observed in city centres. The latent heat flux is negligible on average,but can be large when short time scales are considered (especially afterrainfall). It also suggests that in densely built areas, domesticheating can overwhelm the net radiation, and supply a continuous turbulentheat flux towards the atmosphere. This becomes very important inwinter for continental climates. Finally, a comparison with a vegetation scheme shows that the suburban environment can be represented with a bare soil formulation for large temporal or spatial averages (typical of globalclimatic studies), but that a surface scheme dedicated to the urban surface is necessary when smaller scales are considered: town meteorological forecasts, mesoscale or local studies.     

Intercomparison of three urban climate models

An intercomparison of the surface energy budgets from three urban climate models was made to assess the comparability of results, and to evaluate the surface energy fluxes from each model. The three models selected spanned the continuum of approaches currently employed in the treatment of the effects of urban geometry. The first model was an urban canopy-layer model which explicitly examined urban canyon geometry. The second model treated the city as a warm, rough, moist plate but included greatly simplified parameterizations of urban geometry. Neither model included a dynamic link to the urban boundary-layer. The third model was a one-dimensional urban boundary-layer model which utilized a simple warm, rough, moist plate approach but included a dynamic coupling of the urban surface layer to the urban boundary-layer.Results showed considerable disagreement between the three models in regards to the individual energy fluxes. Average rankings of the energy fluxes in terms of comparability from high-to-low similarity were: (1) solar radiation, (2) sensible heat flux, (3) conduction, (4) latent heat flux, (5) longwave re-radiation, and (6) longwave radiation input. In general, the urban canopy-layer model provided more realistic results, although each model demonstrated strong and weak points. Results indicate that current urban boundary-layer models may produce surface energy budgets with lower sensible heat fluxes and substantially higher latent heat fluxes than is supported by field evidence from the literature.     

A Multi-layer Radiation Model for Urban Neighbourhoods with Trees

A neighbourhood-scale multi-layer urban canopy model of shortwave and longwave radiation exchange that explicitly includes the radiative effects of tall vegetation (trees) is presented. Tree foliage is permitted both between and above buildings, and mutual shading, emission and reflection between buildings and trees are included. The basic geometry is a two-dimensional canyon with leaf area density profiles and probabilistic variation of building height. Furthermore, the model accounts for three-dimensional path lengths through the foliage. Ray tracing determines the receipt of direct shortwave irradiance by building and foliage elements. View factors for longwave and shortwave diffuse radiation exchange are computed once at the start of the simulation using a Monte Carlo ray tracing approach; for subsequent model timesteps, matrix inversion rapidly solves infinite reflections and interception of emitted longwave between all elements. The model is designed to simulate any combination of shortwave and longwave radiation frequency bands, and to be portable to any neighbourhood-scale urban canopy geometry based on the urban canyon. Additionally, the model is sufficiently flexible to represent forest and forest-clearing scenarios. Model sensitivity tests demonstrate the model is robust and computationally feasible, and highlight the importance of vertical resolution to the performance of urban canopy radiation models. Full model evaluation is limited by the paucity of within-canyon radiation measurements in urban neighbourhoods with trees. Where appropriate model components are tested against analytic relations and results from an independent urban radiation transfer model. Furthermore, system response tests demonstrate the ability of the model to realistically distribute shortwave radiation among urban elements as a function of built form, solar angle and tree foliage height, density and clumping. Separate modelling of photosynthetically-active and near-infrared shortwave bands is shown to be important in some cases. Increased canyon height-to-width ratio and/or tree cover diminishes the net longwave radiation loss of individual canyon elements (e.g., floor, walls), but, notably, has little effect on the net longwave loss of the whole urban canopy. When combined with parametrizations for the impacts of trees on airflow and hydrological processes in the urban surface layer, the new radiation model extends the applicability of urban canopy models and permits more robust assessment of trees as tools to manage urban climate, air quality, human comfort and building energy loads.     

The Atmospheric Boundary Layer Over Baltic Sea Ice

A new parametrization for the surface energy balance of urban areas is presented. It is shown that this new method can represent some of the important urban phenomena, such as an urban heat island and the occurrence of a near-neutral nocturnal boundary layer with associated positive turbulent heat fluxes, unlike the traditional method for representing urban areas within operational numerical weather prediction (NWP) models. The basis of the new parametrization is simple and can be applied easily within an operational NWP model. Also, it has no additional computational expense compared to the traditional scheme and is hence applicable for operational forecasting requirements. The results show that the errors for London within the Met Office operational mesoscale model have been significantly reduced since the new scheme was introduced. The bias and root-mean-square (rms) errors have been approximately halved, with the rms error now similar to the model as a whole. The results also show that a seasonal cycle still exists in the model errors, but it is suggested that this may be caused by anthropogenic heat sources that are neglected in the urban scheme.The British Crowns right to retain a non-exclusive royalty-free license in and to any copyright is acknowledged.     

The impact of boundary forcing on RegCM4.2 surface energy budget

The surface energy budget components from two simulations of the regional climate model RegCM4.2 over the European/North African domain during the period 1989–2005 are analysed. The simulations differ in specified boundary forcings which were obtained from ERA-Interim reanalysis and the HadGEM2-ES Earth system model. Surface radiative and turbulent fluxes are compared against ERA-Interim. Errors in surface radiative fluxes are derived with respect to the Global Energy and Water Cycle Experiment/Surface Radiation Budget satellite-based products. In both space and time, we find a high degree of realism in the RegCM surface energy budget components, but some substantial errors and differences between the two simulations are also present. The most prominent error is an overestimation of the net surface shortwave radiation flux of more than 50 W/m² over central and southeastern Europe during summer months. This error strongly correlates with errors in the representation of total cloud cover, and less strongly with errors in surface albedo. During other seasons, the amplitude of the surface energy budget components is more in line with reference datasets. The errors may limit the usefulness of RegCM simulations in applications (e.g. high-quality simulation-driven impact studies). However, by using a simple diagnostic model for error interpretation, we suggest potential sensitivity studies aiming to reduce the underestimation of cloud cover and overestimation of shortwave radiation flux.     

Improving the Representation of the Nocturnal Near-Neutral Surface Layer in the Urban Environment with a Mesoscale Atmospheric Model

A new approach to improve the representation of surface processes in the Global Environmental Multiscale (GEM) atmospheric model associated with the exchanges between the urban canopy and the atmosphere is presented. Effects of the urban canopy on the evolution of surface-layer wind, temperature, moisture, and turbulence are directly parametrized in order to allow realistic interactions between the canopy elements (i.e., roofs, roads, and walls) and the atmosphere at GEM’s multiple vertical levels that are positioned inside the canopy. Surface energy budgets as implemented in the Town Energy Balance (TEB) scheme have been used to determine temperatures of the urban canopy elements for the proposed multilayer scheme. Performance of the multilayer scheme is compared against standard implementations of the TEB scheme for one nighttime intensive observation period of the Joint Urban 2003 experiment held in Oklahoma City, USA. Although the new approach is found to have a negligible impact on urban surface-layer wind profiles, it improves the prediction of near-neutral nocturnal profiles of potential temperature close to the surface. The urban heat island effect is simulated with a better accuracy by the multilayer approach. The horizontal temperature gradient across the central business district of the city along the direction of flow is also reasonably well captured by the proposed scheme.     

A Spatially-Analytical Scheme for Surface Temperatures and Conductive Heat Fluxes in Urban Canopy Models

In the urban environment, surface temperatures and conductive heat fluxes through solid media (roofs, walls, roads and vegetated surfaces) are of paramount importance for the comfort of residents (indoors) and for microclimatic conditions (outdoors). Fully discrete numerical methods are currently used to model heat transfer in these solid media in parametrisations of built surfaces commonly used in weather prediction models. These discrete methods usually use finite difference schemes in both space and time. We propose a spatially-analytical scheme where the temperature field and conductive heat fluxes are solved analytically in space. Spurious numerical oscillations due to temperature discontinuities at the sublayer interfaces can be avoided since the method does not involve spatial discretisation. The proposed method is compared to the fully discrete method for a test case of one-dimensional heat conduction with sinusoidal forcing. Subsequently, the analytical scheme is incorporated into the offline version of the current urban canopy model (UCM) used in the Weather Research and Forecasting model and the new UCM is validated against field measurements using a wireless sensor network and other supporting measurements over a suburban area under real-world conditions. Results of the comparison clearly show the advantage of the proposed scheme over the fully discrete model, particularly for more complicated cases.     

A new design of the LAPS land surface scheme for use over and through heterogeneous and non-heterogeneous surfaces: Numerical simulations and tests

Numerical simulations and tests with the recently redesigned land–air parameterization scheme (LAPS) are presented. In all experiments, supported either by one-point micrometeorological, 1D or 3D simulations, the attention has been directed to: (1) comparison of simulation outputs, expressing the energy transfer over and through heterogeneous and non-heterogeneous surfaces, versus observations and (2) analysis of uncertainties occurring in the solution of the energy balance equation at the land–air interface. To check the proposed method for aggregation of albedo, “propagating hole” sensitivity tests with LAPS over a sandstone rock grid cell have been performed with the forcing meteorological data for July 17, 1999 in Baxter site, Philadelphia (USA). Micrometeorological and biophysical measurements from the surface experiments conducted over crops and apple orchard in Serbia, Poland, Austria and France were used to test the operation of LAPS in calculating surface fluxes and canopy environment temperatures within and above plant covers of different densities. In addition, sensitivity tests with single canopy covers over the Central Europe region and comparison against the observations taken from SYNOP data using 3D simulations were made. Validation of LAPS performances over a solid surface has been done by comparison of 2 m air temperature observations against 5-day simulations over the Sahara Desert rocky ground using 3D model. To examine how realistically the LAPS simulates surface processes over a heterogeneous surface, we compared the air temperature measured at 2 m and that predicted by the 1D model with the LAPS as the surface scheme. Finally, the scheme behaviour over urban surface was tested by runs over different parts of a hypothetical urban area. The corresponding 1D simulations were carried out with an imposed meteorological dataset collected during HAPEX-MOBILHY experiment at Caumont (France). The quantities predicted by the LAPS compare well with the observations and the various subcomponents of the scheme appear to operate realistically.