Scenario of particulate trace metal and metalloid transport during a major flood event inferred from transient geochemical signals

High-resolution sampling (every 3 h) of SPM was performed during a major flood event in a heterogeneous, medium scale watershed of the Garonne-Gironde fluvial-estuarine system (the Lot River; A = 10,700 km²; Q = 151 m³/s). Particulate metal and metalloid (Cd, Zn, Pb, Co, Cr, Ni, Mo, V, U, As, Sb, Th) concentrations were compared with monthly data of the same site (Temple site) obtained during 1999–2002. During the flood event, suspended particulate matter (SPM) concentrations closely followed river discharge with a maximum value (1530 mg/L) coinciding with the discharge peak (2970 m³/s). Trace metal/metalloid concentrations showed significant temporal variations and very contrasted responses. Particulate concentrations were similar to baseline values at the beginning of the flood and mostly increased during the event, showing anticlockwise and complex shape hystereses. Comparison of SPM yield (440,000 t) and particulate metal/metalloid fluxes during the flood with annual fluxes (1999–2002) highlights the great importance of major flood events in fluvial transport. Adequate sampling frequency during floods is necessary for reliable annual flux estimates and provides geochemical signals that may greatly improve our understanding of fluvial transport processes. The scenario of SPM and metal and metalloid transport during the flood are reconstructed by combining variations of Zn, Cd and Sb concentrations, concentration ratios (e.g. Zn/Cd, As/Th, Cd/Th) and hysteresis loops. Changes in SPM and metal/metalloid transport during distinct key stages of the flood were attributed to successive dominance of different water masses transporting material from different sources (e.g. industrial point source, bed sediment from reservoirs, plain erosion). Flood management (dam flushing) clearly enhanced the remobilization of up to 30-a old polluted sediment from reservoir lakes. Sediment remobilization accounted for ∼185,000 t of SPM (i.e. 42% of the total SPM fluxes during the flood) and strongly contributed to particulate metal/metalloid transport for Cd (90%), Zn (83%) and Pb (61%). Therefore, flood management needs to be taken into consideration in future models for erosion and pollutant transport.     

Assessment of trace metal and rare earth elements contamination in rivers around abandoned and active mine areas. The case of Lubumbashi River and Tshamilemba Canal,Katanga, Democratic Republic of the Congo

Active and abandoned mine activities constitute the sources of deterioration of water and soil quality in many parts of the world, particularly in the African Copperbelt regions. The accumulation in soils and the release of toxic substances into the aquatic ecosystem can lead to water resources pollution and may place aquatic organisms and human health at risk. In this study, the impact of past mining activity (i.e., abandoned mine) on aquatic ecosystems has been studied using ICP-MS analysis for trace metals and Rare Earth Elements (REE) in sediment samples from Lubumbashi River (RL) and Tshamilemba Canal (CT), Katanga, Democratic Republic of the Congo (DRC). Soil samples from surrounding CT were collected to evaluate trace metal and REE concentrations and their spatial distribution. The extent of trace metal contamination compared to the background area was assessed by Enrichment Factor (EF) and Geoaccumulation Index (I_geo). Additionally, the trace metal concentrations probable effect levels (PELs) for their potential environmental impact was achieved by comparing the trace metal concentrations in the sediment/soil samples with the Sediment Quality Guidelines (SQGs). Spearman's Rank-order correlation was used to identify the source and origin of contaminants. The results highlighted high concentrations of trace metals in surface sediments of CT reaching the values of 40152, 15586, 610, 10322, 60704 and 15152 mg kg⁻¹ for Cu, Co, Zn, Pb, Fe and Mn, respectively. In the RL, the concentrations reached the values of 24093, 2046, 5463, 3340, 68290 and 769 mg kg⁻¹ for Cu, Co, Zn, Pb, Fe and Mn, respectively. The ΣREE varied from 66 to 218 and 142–331 mg kg⁻¹ for CT and RL, respectively. The soil samples are characterized by variable levels of trace metals. The EF analysis showed “extremely severe enrichment” for Cu and Co. However, no enrichment was observed for REE. Except for Mo, Th, U, Eu, Mo, Ho and Tm for which Igeo is classified as “moderately polluted and/or unpolluted”, all elements in different sites are classified in the class 6, “extremely polluted”. The trace metal concentrations in all sampling sites largely exceeded the SQGs and the PELs for the Protection of Aquatic Life recommendation. Cu and Co had positive correlation coefficient values (r = 0.741, P < 0.05, n = 14). This research presents useful tools for the evaluation of water contamination in abandoned and active mining areas.     

Mercury in European agricultural and grazing land soils

Agricultural (Ap, A_p-horizon, 0–20 cm) and grazing land soil samples (Gr, 0–10 cm) were collected from a large part of Europe (33 countries, 5.6 million km²) at an average density of 1 sample site/2500 km². The resulting more than 2 × 2000 soil samples were air dried, sieved to <2 mm and analysed for their Hg concentrations following an aqua regia extraction. Median concentrations for Hg are 0.030 mg/kg (range: <0.003–1.56 mg/kg) for the Ap samples and 0.035 mg/kg (range: <0.003–3.12 mg/kg) for the Gr samples. Only 5 Ap and 10 Gr samples returned Hg concentrations above 1 mg/kg. In the geochemical maps the continental-scale distribution of the element is clearly dominated by geology. Climate exerts an important influence. Mercury accumulates in those areas of northern Europe where a wet and cold climate favours the build-up of soil organic material. Typical anthropogenic sources like coal-fired power plants, waste incinerators, chlor-alkali plants, metal smelters and urban agglomerations are hardly visible at continental scales but can have a major impact at the local-scale.     

Laboratory study of calcite–gypsum sludge–water interactions in a flooded tailings impoundment at the Kristineberg Zn–Cu mine,northern Sweden

Due to liming of acid mine drainage, a calcite–gypsum sludge with high concentrations of Zn (24,400 ± 6900 μg g⁻¹), Cu (2840 ± 680 μg g⁻¹) and Cd (59 ± 20 μg g⁻¹) has formed in a flooded tailings impoundment at the Kristineberg mine site. The potential metal release from the sludge during resuspension events and in a long-term perspective was investigated by performing a shake flask test and sequential extraction of the sludge. The sequentially extracted carbonate and oxide fractions together contained ⩾97% of the total amount of Cd, Co, Cu, Ni, Pb and Zn in the sludge. The association of these metals with carbonates and oxides appears to result from sorption and/or coprecipitation reactions at the surfaces of calcite and Fe, Al and Mn oxyhydroxides forming in the impoundment. If stream water is diverted into the flooded impoundment, dissolution of calcite, gypsum and presumably also Al oxyhydroxides can be expected during resuspension events. In the shake flask test (performed at a pH of 7–9), remobilisation of Zn, Cu, Cd and Co from the sludge resulted in dissolved concentrations of these metals that were significantly lower than those predicted to result from dissolution of the carbonate fraction of the sludge. This may suggest that cationic Zn, Cu, Cd and Co remobilised from dissolving calcite, gypsum and Al oxyhydroxides were readsorbed onto Fe oxyhydroxides remaining stable under oxic conditions. In a long-term perspective (≳10² a), ⩾97% of the Cd, Co, Cu, Ni, Pb and Zn content of the sludge potentially is available for release by dissolution of calcite and reductive dissolution of Fe oxyhydroxides if the sludge is subject to a soil environment with lower dissolved Ca concentrations, pH and redox than in the impoundment.     

A regional-scale geochemical survey of soil O and C horizon samples in Nord-Trøndelag,Central Norway: Geology and mineral potential

A highly efficient, low-density sampling strategy was employed to study the geochemical expression of geological bodies and the mineral potential on the county scale in Central Norway. Soil O and C horizon samples (N = 752) were collected in Nord-Trøndelag and parts of Sør-Trøndelag, and analysed for 53 chemical elements (Ag, Al, As, Au, B, Ba, Be, Bi, Ca, Cd, Ce, Co, Cr, Cs, Cu, Fe, Ga, Ge, Hf, Hg, In, K, La, Li, Mg, Mn, Mo, Na, Nb, Ni, P, Pb, Pd, Pt, Rb, Re, S, Sb, Sc, Se, Sn, Sr, Ta, Te, Th, Ti, Tl, U, V, W, Y, Zn, and Zr) and Pb isotopes in an aqua regia extraction. At the sample density of one site/36 km² the four metal deposits, which have been mined in the area within the last 50 years were all detected as geochemical anomalies. In addition, a number of new anomalies that may warrant follow-up surveys were found. In terms of geology the Grong–Olden Culmination is marked by a distinct ²⁰⁶Pb/²⁰⁷Pb isotope anomaly. Geochemical differences distinguish the most important belts of mafic metavolcanic lithologies in the area. Though the Fosdalen iron ore deposit is only marked in the soil O horizon, the C horizon outlines the more prominent anomalies of possibly economic interest. Climatic factors like the input of marine aerosols along the coast are clearly visible in the soil O horizon. Low-density geochemical mapping of two sample materials provides important complementing information for the interpretation of the geochemical variation in Nord-Trøndelag county.     

Measuring reactive pools of Cd,Pb and Zn in coal fly ash from the UK using isotopic dilution assays

Large volumes of coal fly ash are continually being produced and stockpiled around the world and can be a source of environmentally sensitive trace elements. Whilst leaching tests are used for regulatory purposes, these provide little information about the true geochemical behaviour and ‘reactivity’ of trace elements in coal ash because they are poorly selective. Isotope dilution (ID) assays are frequently used in soil geochemistry as a means of measuring the reactive pools of trace metals that are in equilibrium with soil pore waters. This paper examines the applicability of multi-element ID assays in measuring the labile or reactive pool of Cd, Pb and Zn in a range of fresh and weathered fly ash, where pH is generally much more alkaline than in soils. The method generally worked well using 0.0005 M EDTA as a background electrolyte as it provided robust analytical ICP-MS measurements as well as fulfilling the important principle of ID that non-labile metal should not be solubilised. Reactive pools were equivalent to 0.5–3% of the total Pb pool and 4–13% of the total Cd pool. For Zn, where samples had pH < 11.5, the reactive Zn pool varied between 0.3% and 2%; when fresh ash samples with pH > 11.5 were tested, the method failed as the spiked isotope appeared to be sorbed or precipitated. Ash weathering was found to exert little impact on the lability of Cd, Pb and Zn. Isotope dilution results were compared with 0.43 M HNO₃ and 0.05 M EDTA extractions, these commonly being used as analogues of the ID assay, and concluded that these can be used as fast, cost-effective and simple proxies for the ID assays. Results suggest that ID methods can be used to enhance knowledge of trace element behaviour in fresh and weathered fly ash.     

Toxic metal(loid) speciation during weathering of iron sulfide mine tailings under semi-arid climate

Toxic metalliferous mine-tailings pose a significant health risk to ecosystems and neighboring communities from wind and water dispersion of particulates containing high concentrations of toxic metal(loid)s (e.g., Pb, As, Zn). Tailings are particularly vulnerable to erosion before vegetative cover can be reestablished, i.e., decades or longer in semi-arid environments without intervention. Metal(loid) speciation, linked directly to bioaccessibility and lability, is controlled by mineral weathering and is a key consideration when assessing human and environmental health risks associated with mine sites. At the semi-arid Iron King Mine and Humboldt Smelter Superfund site in central Arizona, the mineral assemblage of the top 2 m of tailings has been previously characterized. A distinct redox gradient was observed in the top 0.5 m of the tailings and the mineral assemblage indicates progressive transformation of ferrous iron sulfides to ferrihydrite and gypsum, which, in turn weather to form schwertmannite and then jarosite accompanied by a progressive decrease in pH (7.3–2.3).Within the geochemical context of this reaction front, we examined enriched toxic metal(loid)s As, Pb, and Zn with surficial concentrations 41.1, 10.7, 39.3 mmol kg⁻¹ (3080, 2200, and 2570 mg kg⁻¹), respectively. The highest bulk concentrations of As and Zn occur at the redox boundary representing a 1.7 and 4.2-fold enrichment relative to surficial concentrations, respectively, indicating the translocation of toxic elements from the gossan zone to either the underlying redox boundary or the surface crust. Metal speciation was also examined as a function of depth using X-ray absorption spectroscopy (XAS). The deepest sample (180 cm) contains sulfides (e.g., pyrite, arsenopyrite, galena, and sphalerite). Samples from the redox transition zone (25–54 cm) contain a mixture of sulfides, carbonates (siderite, ankerite, cerrusite, and smithsonite) and metal(loid)s sorbed to neoformed secondary Fe phases, principally ferrihydrite. In surface samples (0–35 cm), metal(loid)s are found as sorbed species or incorporated into secondary Fe hydroxysulfate phases, such as schwertmannite and jarosites. Metal-bearing efflorescent salts (e.g., ZnSO₄·nH₂O) were detected in the surficial sample. Taken together, these data suggest the bioaccessibility and lability of metal(loid)s are altered by mineral weathering, which results in both the downward migration of metal(loid)s to the redox boundary, as well as the precipitation of metal salts at the surface.     

Measurement of labile metals in acid rock drainage springs,New Zealand: Field application of anodic stripping voltammetry

Spring waters were analysed in the field by anodic stripping voltammetry, using equipment which is sufficiently portable to be useful in a remote heavily forested area accessible by foot only. The equipment and techniques are capable of producing analyses on site to the μg/L level for labile metals. Field analysis avoids issues of sample storage and transport protocols that limit confidence in laboratory measurements of labile elements. Samples were taken as a feedback to immediate analysis resulting in a fine grid map of the geological site. Acid rock drainage emanates from a New Zealand historic mine site, with elevated concentrations of metals. However, ground water and surface water discharging naturally from mineralised rocks in the same area also have elevated levels of metals. This study quantifies natural metalliferous discharges from a single site, and compares this to the overall metal flux from the mine area. Acid (pH 3) metalliferous springs emanate from colluvium and bedrock in a young (months-old) landslide. Labile Cu, Pb, Zn and Cd are the environmentally most significant metals in the studied area. Labile metal concentrations observed in the natural springs are up to 24 μg/L Cu, up to 50 μg/L Pb, up to 5 μg/L Cd and up to 9 mg/L Zn. Labile Cu and Zn concentrations are similar to laboratory-determined total concentrations, whereas labile Pb and Cd concentrations are generally distinctly lower than total Pb and Cd concentrations. Four different spring water compositions occur within metres of each other: acid metalliferous water with high Pb, acid metalliferous water with low Pb, high Cu, Pb, Zn acid water and high pH water with elevated Cu. High metal concentrations in these waters are readily attenuated by adsorption to Fe oxyhydroxides (HFO), especially when rain raises spring water pH at the surface. Copper, Pb and Cd are >99% adsorbed, and Zn >95% adsorbed, during this rainfall dilution. Natural spring waters have potential to contribute up to 10% of the total Zn flux from the catchment, but negligible proportions of Cu, Pb and Cd.     

Metal and arsenic distribution in soil particle sizes relevant to soil ingestion by children

Ingestion of soil is a common behaviour in young children as a means of exploring their surroundings. Much attention has been given to remediation of point-source polluted sites with regard to potential health risks for children. However, because of diffuse pollution and long-range atmospheric deposition, soil contaminant levels are generally increased in urban areas compared to their rural counterparts, even in areas located away from any point sources of pollution. Intake of urban soil can thereby result in significant amounts of the child’s daily metal intake. In the present study, soil samples were collected from 25 playgrounds around urban Uppsala, Sweden and analysed for contents of Al, As, Fe, Cr, Cu, Cd, Hg, Mn, Ni, Pb, W and Zn. Prior to aqua regia digestion, the samples were wet-sieved in order to separate soil particle fractions representing deliberate (<4 mm) and involuntary (<50 μm) soil ingestion by children, as well as a third size fraction of 50–100 μm representing soil that is easily transported by suspension. While the metal and As contents in the 50–100 μm fraction were similar to those of the <4 mm fraction, the <50 μm fraction had metal and As contents on average one and a half times higher than those of the <4 mm fraction. The metal and As contents correlated negatively with the sand content in both particle size fractions <4 mm and 50–100 μm, suggesting a general decrease in metal and As content with increasing sand content. However, a positive correlation was found between sand content and the metal and As contents of the finest fraction (<50 μm), suggesting that when the sand content is high, the bulk of the sorbed elements are on the finest particles. The difference between metal and As contents in the different size fractions was greater in the soil sample with the highest sand content than in the sample with the lowest sand content. This implies that texture is a significant factor in metal and As distribution in soils with moderate metal and As contents, when the number of binding sites associated with small particles is low. Tolerable daily intake (TDI) values for Pb and As were exceeded at all sites, and at two sites for Cd, for children with pica behaviour. A high ingestion rate of mainly small particles could also result in the TDI value for Pb being exceeded at 10 sites and that for As at one site. This study also found that soil analysis by the procedure recommended by Swedish authorities accurately represents the metal intake from deliberate soil ingestion, whereas involuntary soil ingestion of mainly small particles could result in metal intakes which are up to twice as high.     

Statistical categorization geochemical modeling of groundwater in Ain Azel plain (Algeria)

Water analysis data of 54 groundwater samples from 18 uniformly distributed wells were collected during three campaigns (June, September and December 2004). Q-mode hierarchical cluster analysis (HCA) was employed for partitioning the water samples into hydrochemical facies. Interpretation of analytical data showed that the abundance of major ions was identified as follows: Ca ? Mg > Na > K and HCO₃ ? Cl > SO₄. Three major water facies are suggested by the HCA analysis. The samples from the area were classified as recharge area waters (Ca–Mg–HCO₃ water), transition area waters (Mg–Ca–HCO₃–Cl water), and discharge area waters (Mg–Ca–Cl–HCO₃ water). Inverse geochemical modeling suggests that relatively few phases are required to derive the water chemistry in the area. In a broad sense, the reactions responsible for the hydrochemical evolution in the area fall into two categories: (1) evaporite weathering reactions and (2) precipitation of carbonate minerals.     

Environmental assessment of abandoned mine tailings in Adak,Västerbotten district (northern Sweden)

Sulfide-rich mine tailings in Adak that are exposed to weathering cause acid mine drainage characterized by low pH (2–4) and high SO₄ (up to 800 mg L⁻¹). Surface water, sediment and soil samples collected in this study contain higher concentrations of As, Cu, Fe and Zn, compared to the target and/or intervention limits set by international regulatory agencies. In particular, high As concentrations in water (up to 2900 μg L⁻¹) and sediment (up to 900 mg kg⁻¹) are of concern. There is large variability in trace element concentrations, implying that both physical (grain size) and chemical factors (pH, secondary phases as sulfides, Al-oxides or clay minerals) play an important role in their distribution. The low pH keeps the trace elements dissolved, and they are transported farther downstream. Trace element partition coefficients are low (log K_d = 0.3–4.3), and saturation indices calculated with PHREEQC are <0 for common oxide and sulfidic minerals. The sediment and soil samples indicate an enhanced pollution index (up to 17), and high enrichment factors for trace elements (As up to 38,300; Zn up to 800). Finally, leaves collected from different plant types indicate bioaccumulation of several elements (As, Al, Cu, Fe and Zn). However, some of the plants growing in this area (e.g., Salix, Equisétum) are generally resistant to metal toxicity, and hence, liming and phytoremediation could be considered as potential on-site remediation methods.     

The nature and distribution of Cu,Zn, Hg,and Pb in urban soils of a regional city: Lithgow,Australia

This study investigates the concentration and spatial distribution of Cu, Zn, Hg and Pb in the surface (0–2 cm) soils of a regional city in Australia. Surface soils were collected from road sides and analysed for their total Cu, Zn, Hg and Pb concentrations in the <180 μm and <2 mm grain size fractions. The average metal concentration of surface soils, relative to local background soils at 40–50 cm depth, are twice as enriched in Hg, more than three times enriched in Cu and Zn, and nearly six times as enriched in Pb. Median surface soil metal concentration values were Cu – 39 mg/kg (682 mg/kg max), Zn – 120 mg/kg (4950 mg/kg max), Hg – 44 μg/kg (14,900 μg/kg max) and Pb – 46 mg/kg (3490 mg/kg max). Five sites exceeded the Australian NEPC (1999) 300 mg/kg guideline for Pb in residential soils. Strong positive correlations between Cu, Zn and Pb, coupled with the spatial distribution of elevated soil concentrations towards the city centre and main roads suggest traffic and older housing as major sources of contamination. No spatial relationships were identified between elevated metal loadings and locations of past or present industries.     

Evidence for SEDEX-style mineralization in the 1.7 Ga Tawallah Group,McArthur Basin,Australia

The Paleoproterozoic McArthur Basin (McArthur Group) of northern Australia hosts world-class sedimentary ‘exhalative’ (SEDEX) McArthur type Zn–Pb deposits, which are largely hosted within a sequence of 1.64 Ga pyritic carbonaceous shales deposited in an extensional rift setting. A well-known example of these is McArthur River (or Here's Your Chance [HYC] Zn–Pb–Ag deposit). The ~ 1.78 Ga McDermott and ~ 1.73 Ga Wollogorang formations (Tawallah Group) both contain carbonaceous shales deposited in similar environments. Our observations suggest the carbonaceous facies of the Wollogorang Formation were deposited under mostly euxinic conditions, with periodically-high concentrations of sedimentary pyrite deposition. The carbonaceous shales in the older McDermott Formation contain considerably less early pyrite, reflecting a mostly sulfide-poor, anoxic depositional environment. Localized fault-bound sub-basins likely facilitated lateral facies variations, which is evident from synsedimentary breccias.The presence of evaporitic oxidized facies within the McDermott and Wollogorang formations, alongside evidence for synsedimentary brecciation in reduced shales are favourable criteria for SEDEX-style base metal deposition. Both formations overlie volcanic units, which could have been sources of base metals. Detailed X-ray petrography, new geochemical data and sulfur isotope data from historical drill cores indicate multiple horizons of stratiform and sediment breccia-hosted base metal sulfide within carbonaceous shale units, with high-grade Zn concentrations. A close association between sphalerite and ferromanganean dolomite alteration draws comparisons with younger SEDEX mineralization at HYC. Additionally, SEDEX alteration indices, used demonstrably as a vector to the younger orebodies, indicate the sedimentary rocks analyzed in this study are marginally below the ore window when compared to the overlying mineralized stratigraphy.Our data imply that localized active circulation of metalliferous brines occurred in the Tawallah Group basin. High-grade sulfide deposition in reduced facies alteration may represent distal expressions of larger SEDEX-style deposits. Furthermore, abundant pyrite and high molybdenum in the Wollogorang Formation suggest the global oceanic sulfate concentration was sufficient by ~ 1.73 Ga to engender intermittent but strong bottom-water euxinia during shale deposition, thus providing a robust chemical trap for base metal sulfide mineralization.     

Investigations of karstic springs of the Biokovo Mt from the Dinaric karst of Croatia

Ten gravity springs from the slopes of the Biokovo Mt, Adriatic coast of Croatia were investigated. Three of them are included in the regional water supply system. The aim of this study was to investigate hydrogeological and geochemical characteristics of watershed, presenting one of the most typical karstic areas in the world.Hydrogeological investigations were performed during two seasons with dye tracing, using Na-fluoresceine which was poured into two pits, observing springs at distances of 1.82–8.8 km. Apparent velocities were 0.21–0.51 cm s^?1. Dye tracing was first time partially effective and second time ineffective, what could be due to immanent ore mineralization, which presents a natural barrier and was discovered by geochemical and mineralogical methods.Concentrations of 17 dissolved and total trace elements were determined first time in groundwater samples. Their concentrations were extremely low, more than 3 orders of magnitude less than allowed by the Croatian directives for the first category of groundwater and drinking water. The mass fractions of 60 elements were determined in 3 representative spring sediments. Highest concentrations of some metals in sediments (mg kg^?1) are: lead 5440, chromium 118, manganese 935, zinc 116 and barium 238. Origin of some elements and mineralogy is discussed.     

Mechanisms controlling acid neutralization and metal mobility within a Ni-rich tailings impoundment

Low-quality pore waters containing high concentrations of dissolved H⁺, SO₄, and metals have been generated in the East Tailings Management Area at Lynn Lake, Manitoba, as a result of sulfide-mineral oxidation. To assess the abundance, distribution, and solid-phase associations of S, Fe, and trace metals, the tailings pore water was analyzed, and investigations of the geochemical and mineralogical characteristics of the tailings solids were completed. The results were used to delineate the mechanisms that control acid neutralization, metal release, and metal attenuation. Migration of the low-pH conditions through the vadose zone is limited by acid-neutralization reactions, resulting in the development of distinct pore-water pH zones at depth; the neutralization reactions involve carbonate (pH ⩾ 5.7), Al-hydroxide (pH ⩾ 4.0), and aluminosilicate solids. As the zone of low-pH pore water expands, the pH will then be primarily controlled by less soluble solids, such as Fe(III) oxyhydroxides (pH < 3.5) and the relatively more recalcitrant aluminosilicates (pH ⩾ 1.3). Precipitation/dissolution reactions involving secondary Fe(III) oxyhydroxides and hydroxysulfates control the concentrations of dissolved Fe(III). Concentrations of dissolved SO₄ are principally controlled by the formation of gypsum and jarosite. Geochemical extractions indicate that the solid-phase concentrations of Ni, Co, and Zn are associated predominantly with reducible and acid-soluble fractions. The concentrations of dissolved trace metals are therefore primarily controlled by adsorption/complexation and (or) co-precipitation/dissolution reactions involving secondary Fe(III) oxyhydroxide and hydroxysulfate minerals. Concentrations of dissolved metals with relatively low mobility, such as Cu, are also controlled by the precipitation of discrete minerals. Because the major proportion of metals is sequestered through adsorption and (or) co-precipitation, the metals are susceptible to remobilization if low-pH or reducing conditions develop within the tailings.     

Biogeochemical indicators of buried mineralization under cover,Talbot VMS Cu–Zn prospect,Manitoba

Results are presented of a surficial geomicrobiological investigation of glacial cover overlying buried mineralization at the Talbot prospect, Manitoba, Canada, where previous surficial geochemistry surveys indicated anomalous concentrations of elements above the buried mineralization. The Cu–Zn volcanogenic massive sulfide (VMS) occurrence is overlain by 100 m of Paleozoic dolomites and Quaternary glacial cover. The geomicrobiological investigation demonstrates that there is a distinct microbial ecology at the anomalous sampling locations, especially directly overlying buried mineralization. The combined geochemical and geomicrobiological analyses reveal the presence of an anomaly directly over mineralization due to oxidation of the buried ore. Specifically, geomicrobiological analyses yield an inverse correlation between Zn in the clay-size (<2 μm) fraction and total microbial biomass and a direct correlation between Cu in the clay-size (<2 μm) fraction and abundance of methanotrophic bacteria. These results demonstrate that microbiological analyses can be a useful addition to geochemical exploration by revealing metal transport and sequestration processes and enhancing surficial anomalies.     

Diel variation of arsenic,molybdenum and antimony in a stream draining natural As geochemical anomaly

The Mokrsko Stream in the central Czech Republic is an oxic and slightly alkaline stream that drains a natural As geochemical anomaly. Although long-term monitoring has characterized the general seasonal trends in trace element concentrations (i.e., As, Mo, Cu, Zn) in this stream, little is known about solubility controls and sorption processes that influence diel cycles in trace element concentrations. Trace elements (including As species, Cu, Mn, Mo, Pb and Sb) and other parameters were monitored over two 24-h periods in unfiltered and filtered (0.1 μm) samples collected in August 2010 and June 2011. Copper and Pb were predominantly (>92% of the mass) associated with the particulate fraction (>0.1 μm). Arsenic, Mo and Sb were predominantly (>88% of the mass) in the “dissolved” (<0.1 μm) form. Particulate-associated elements displayed up to a factor of 13 differences between minimum and maximum concentrations, most likely due to increased streamflow related to rainfall events. Dissolved concentrations of the trace metal cations (Cu, Fe, Mn and Pb) were consistently low and displayed no diel trends. Dissolved As(V), Mo and Sb varied on a diel cycle, with increased concentrations (up to 36%) during the late afternoon and decreased concentrations during the nighttime. Diel trends in trace anionic elements are explained by temperature-dependent sorption, as the diel changes in pH during base flow were very small (0.07 std. units). Very low concentrations of As(III), which have been shown to vary in a diel cycle, were attributed to enhanced hydraulic exchange with As(III)-rich hyporheic water during rainfall events.     

The Diavik waste rock project: Initial geochemical response from a low sulfide waste rock pile

Three large-scale experimental waste rock piles (test piles) were constructed and instrumented at the Diavik Diamond Mine in the Northwest Territories, Canada, as part of an integrated field and laboratory study to measure and compare physical and geochemical characteristics of experimental, low sulfide waste rock piles at various scales. This paper describes the geochemical response during the first season from a test pile containing 0.053 wt.% S. Bulk drainage chemistry was measured at two sampling points for pH, Eh, alkalinity, dissolved cations and anions, and nutrients. The geochemical equilibrium model MINTEQA2 was used to interpret potential mineral solubility controls on water chemistry. The geochemical response characterizes the initial flushing response of blasting residues and oxidation products derived from sulfides in waste rock exposed to the atmosphere for less than 1 year. Sulfate concentrations reached 2000 mg L⁻¹ when ambient temperatures were >10 °C, and decreased as ambient temperatures declined to <0 °C. The pH decreased to <5, concomitant with an alkalinity minimum of <1 mg L⁻¹ (as total CaCO₃), suggesting all available alkalinity is consumed by acid-neutralizing reactions. Concentrations of Al and Fe were <0.36 and <0.11 mg L⁻¹, respectively. Trends of pH and alkalinity and the calculated saturation indices for Al and Fe (oxy)hydroxides suggest that dissolution of Al and Fe (oxy)hydroxide phases buffers the pH. The effluent water showed increased concentrations of dissolved Mn (<13 mg L⁻¹), Ni (<7.0 mg L⁻¹), Co (<1.5 mg L⁻¹), Zn (<0.5 mg L⁻¹), Cd (<0.008 mg L⁻¹) and Cu (<0.05 mg L⁻¹) as ambient temperatures increased. Manganese is released by aluminosilicate weathering, Ni and Co by pyrrhotite [Fe_1−xS] oxidation, Zn and Cd by sphalerite oxidation, and Cu by chalcopyrite [CuFeS₂] oxidation. No dissolved metals appear to have discrete secondary mineral controls. Changes in SO₄, pH and metal concentrations indicate sulfide oxidation is occurring and effluent concentrations are influenced by ambient temperatures and, possibly, increasing flow path lengths that transport reaction products from previously unflushed waste rock.     

Levels of selected potential harmful elements (PHEs) in soils and vegetables used in diet of the population living in the surroundings of the Estarreja Chemical Complex (Portugal)

This study was carried out to analyze the distribution and soil–plant transfer of selected potential harmful elements (PHEs: As, Hg and Zn) in soils and in two edible horticultural crops (cabbage, Brassica oleracea L., and tomato, Lycopersicon esculentum Mill). randomly sampled in kitchen gardens/small farms around one of the most important and old Portuguese industrial areas (Estarreja Chemical Complex-ECC). The results show that 46% and 11.5% of the soils present high total As (12–532 mg/kg) and Hg (6.6–13.65 mg/kg) concentrations that exceed protective health Canadian soil quality guidelines. Soil As and Zn available fractions are also of concern for groundwater and crops contamination as more than 84% of the samples were above the trigger value proposed by the German legislation for both elements (0.4 and 2 mg/kg, respectively). In the horticultural crops the cabbage leaves concentrate more the PHEs (max.: 3.5, 0.08 and 746 mg/kg dw for As, Hg and Zn, respectively) than the tomato fruit (max.: 0.4, 0.02 and 82 mg/kg dw, respectively). The highest concentration of the study PHEs in soils and horticultural crops were found near sewage outlets that are chiefly related to historical industrial activities mostly from arsenopyrite roasting and a chloralkali plant. The values of estimated bioaccumulation and bioconcentration coefficients suggested exclusion mechanisms for transfer of As to edible cabbage and tomato tissues and cabbage Zn tolerance capacity. The concentration of the PHEs in the edible horticultural crops tissues were not directly related with respective soil total concentration or available fractions, specially for As and Hg. Sampling locations with the highest concentrations of As, Hg, Zn in soil and vegetable foodstuffs should be sites to foregoing research and human daily intakes should be investigated in order to evaluate potential health risks.     

Dissolved and particulate zinc and nickel in the Yangtze River (China): Distribution,sources and fluxes

Dissolved and particulate Zn and Ni concentrations were determined at 76 locations along the Yangtze River basin from the headwaters to the estuary during flood and dry seasons. Spatial and temporal variations of Zn and Ni were investigated and six major source zones were identified. The Three Gorges Dam (TGD) blocked most of the suspended loads and extremely low concentration of Zn and Ni were observed downstream of the dam. Dissolved (ranging from 0.062 to 8.0 μg L⁻¹) and particulate (ranging from 12 to 110 mg kg⁻¹) Ni showed similar levels of concentrations during flood and dry seasons, whereas dissolved (ranging from 0.43 to 49 μg L⁻¹) and particulate (ranging from 54 to 1100 mg kg⁻¹) Zn were slightly and much lower in the flood season than dry season, respectively. This was attributed to the increased water discharge during the flood season causing a dilution effect and sediment resuspension. In the flood season, average concentrations of Zn and Ni were higher in the main channel than in tributaries, due to soil erosion and mining activities providing the dominant inputs. The situation was opposite in the dry season, attributed to the contribution of municipal sewage, industrial activities, and waste disposal. During the flood season, dissolved Zn and Ni concentrations were negatively correlated with pH. Water and suspended particulate matter (SPM) from the upper reaches, middle reaches, and lower reaches of the Yangtze River were characterized by their Zn and Ni concentrations. The Panzhihua, Nanling and Tongling mining areas were considered as the most important source zones of particulate Zn and Ni. The Chongqing region, Wuhan region and the Yangtze River Delta provided most of the dissolved Zn and Ni inputs into the river. Annual net flux of Zn (10–72 × 10⁵ kg a⁻¹) and Ni (5.0–19 × 10⁵ kg a⁻¹) in each source zone were estimated according to their respective influent and effluent fluxes. Contributions of the source zones to Zn and Ni transport decreased from the upper reaches to the lower reaches.