Semi-determinate hydraulic geometry of river channels,South Island,New Zealand

Data to describe the morphologic, hydrologic and sedimentologic characteristics of 72 South Island, New Zealand, rivers were collected and analysed. Nearly 70 per cent of variation in channel morphology is accounted for by differences in cross-sectional area, slope, and cross-section shape; only 53 per cent of the morphologic variability could be statistically ‘explained’ by the hydrologic and sediment variables used. The level of explanation varied for different morphologic variables; nearly 90 per cent of the variability in cross-sectional area could be explained, but aspect ratio (maximum depth divided by hydraulic radius) was completely independent. Apart from the inadequacy of the measured variables as indices of the true underlying controlling factors, and the imperfect measurement and sampling procedures, the low level of explanation is probably due to the influence of factors such as floodplain vegetation, high quasi-random variability in bark sediment character, boundary effects imposed by bedrock bluffs, and the precise sequence of flood events, none of which are easily quantified. In addition, observations indicate that there is a large random variation in channel form which cannot be related to any factor. An attempt to relate channel morphology to flow variability, using simple indices of the latter, was unsuccessful.     

Slope-induced changes in channel character along a gravel-bed stream: The Allt Dubhaig,Scotland

Changes in channel character along a small river in the Scottish Highlands are described using measurements in seven reaches over a 3 km length with no significant tributaries but a decline in slope from 0.02 to 0.00015 because of local baselevel control. This decline in slope is associated with rapid downstream fining of the gravel bed followed by an abrupt transition to a sand bed. The channel pattern alters progressively rather than abruptly, in the sequence (1) near-braided, (2) meandering with active point-bar chutes, (3) meandering with active outer-bank talweg, (4) stable equiwidth sinuous. The changes in channel pattern and hydraulic geometry are predicted better by rational approaches based on critical shear stress or other physical concepts than by purely empirical discriminant or trend equations. Measurements in five reaches confirm a downstream decrease in shear stress and the amount and calibre of bedload. It is argued that the downstream changes in channel character in this stream are induced by profile concavity inherited from deglacial conditions, are typical of many streams in mountainous areas and can be understood in terms of slope-induced changes in hydraulic properties.     

Simulation of flow geometry in a riffle-pool stream

The nature of the flow in most natural streams is gradually varied rather than uniform. This is particularly true of streams with coarse gravel bed material organized into relatively stable riffle and pool features. In spite of this, there are few applications of the gradually varied flow models (e.g. the Bernoulli equation) to such streams. This paper presents some initial results of a simulation of flow patterns in two riffle-pool reaches, using an open channel flow profile computation method based on an equation defining an energy balance between successive cross-sections separated by an incremental distance.     

The influence of roughness geometry and Shields parameter on flow resistance in gravel-bed channels

The spatial variability of bed particles of a gravel-bed channel is analysed and treated experimentally in order to simulate the effects of the arrangement of coarse bed elements on the flow resistance law. For the studied bed patterns, characterized by the concentration Γ of coarser elements arranged on the bed layer, a particle arrangement parameter α is proposed. The α parameter is useful for estimating the intercept b₀ of the semi-logarithmic flow resistance law deduced by flume measurements carried out for the hydraulic condition of large-scale and transition roughness. The differences between the experimental friction factor parameter values and the ones calculated by the proposed semi-logarithmic relationship are explained by the ratio between the Shields parameter and its critical value. The analysis shows that estimates of the friction factor parameter are not improved by introducing the Froude number into the flow resistance law. © 1997 by John Wiley & Sons, Ltd.     

Bed morphology and generation of step–pool channels

Flume experiments have been carried out to study the formation processes and the bed morphology of step–pool channels. From the experiments different step types and step configurations could be distinguished depending on the stream power. These step types can be seen as an image of the generation mechanisms of step–pool systems. These results suggest that the bed roughness geometry develops towards a condition that provides the maximum possible bed stability for a given grain size distribution. In contrast to a variety of other studies, antidunes did not contribute to the generation of the step structures. However, the data of the presented study fits well into the region of antidune formation proposed by Kennedy for sand‐bed rivers. This observation points out that step–pool field‐data located in the Kennedy region do not inevitably prove that antidunes played a role in step development. It is rather proposed that in Kennedy's region of antidune formation there exist hydraulic conditions where the flow resistance is maximized. It is suggested that such maximum flow resistance is associated with an optimal distance between the bedforms and their height, independently of whether these are antidunes in sand‐ and gravel‐bed rivers or step–pool units in boulder‐bed streams. The considerations of the Kennedy region of antidune formation and the analysis of planform step types depending on stream power both suggest that steep channels have a potential for self‐stabilization by modifying the step–pool structure towards a geometry that provides maximum flow resistance and maximum bed stability. Copyright © 2008 John Wiley & Sons, Ltd.     

Virtual rate and mean distance of travel of individual clasts in gravel-bed channels

Travel distances in gravel-bed rivers of tagged particles of various sizes are related to excess stream power estimated for peak discharge. Mean distance of movement, irrespective of grain size, is weakly correlated with stream power, especially near the threshold of movement. There may be several reasons for the weak correlation, including variable effects of bed structure, varying magnitudes of sediment mobilizing events and sampling problems. Grain size itself is of marginal significance. The virtual rate of travel calculated using total time for which the flow is larger than that needed to initiate clast movement also bears a weak relation to the excess stream power over the period. Better results are obtained by relating the virtual rate of travel to the first peak of the flow event only. This implies that the initial seeding of the tagged particles dominates the observations. Nonetheless, an underlying general relation is indicated by the data, which are derived from a wide range of flow regime types.     

Bed stability variations after check dam construction in torrential channels (South‐East Spain)

The effects of check dams on the bed stability of torrential channels have been analysed in several tributary basins of the Segura and Guadalentín rivers (South‐East Spain). In order to illustrate the large variability in channel bed‐forms and bed sediment sizes along the stream, 52 reaches of 150 m in length were surveyed. This variability is due to the behaviour of check dams, which depends on bedrock control, bed slope, channel roughness, lateral sediment input and a highly variable sediment transport capacity. Though the purpose of check dams is to diminish the boundary shear stress, reducing the longitudinal slope, and to stabilize the channel bed, downstream they reduce the volume of channel‐stored material, favouring local scour processes, and upstream they can destabilize the sidewalls. The results enable us to evaluate the impact of every check dam on the bed morphology, distinguishing the structures installed in limy marl areas (e.g. catchment of the Cárcavo rambla, Cieza) and in schist and slate terrains (e.g. catchment of the Torrecilla rambla, close to Lorca). In the first type, bedrock and moderately thick granular beds predominate downstream from the check dams, so that the length of bedrock reaches and increase of roughness due to scour processes are the best indicators to verify its geomorphological effectiveness. On the other hand, the metamorphic areas drained by ramblas and gullies produce great quantities of gravel that are retained by check dams, creating more uniform and permeable beds, where the balance between sedimentation and scouring, and the ratio τ_c84/τ₀ (RBS), appear to be the parameters most frequently adopted to estimate the bed stability. Analysis of slope adjustments and the application of other indices to estimate the bed substrate stability (LRBS, SRI) and the structural influence of the dams (SIBS) corroborate the differences in bed stability found in the corrected reaches in each catchment. Copyright © 2007 John Wiley & Sons, Ltd.     

Hydraulic geometry and changes in flow velocity at a river confluence with coarse bed material

A survey of flows was conducted at a river confluence with coarse bed material. Bridges were installed on both tributaries, at the confluence and farther downstream on the receiving stream. At these stations, flow velocities were measured over a dense grid for seven conditions ranging from very low flows to the bankfull stage. Hydraulic geometry relationships established at all four stations revealed that flow is accelerated through the confluence as stage rises. At bankfull discharge, average velocity is 1.6 times higher at the confluence than on either tributary. Flow acceleration occurs at and above intermediate flow stages and is concentrated at the centre of a linear pool located at the confluence. The development of a zone of high shear stress is also associated with the cell of high flow velocity. Flow acceleration is dissipated at the exit of the pool where water surges over boulder ribs. The acceleration is not related to the development of flow separation zones as observed by Best and Reid (1984) for wide junction angles, nor is it explained by the reduction of the friction exerted by the banks. Acceleration is associated with the plan geometry of the confluence, with the lateral slopes which permit water to converge, and with a reduction in grain roughness at the confluence. Owing to the curvature of the tributary and to the acute angle of entry, relative power losses through the confluence decrease with increasing stages.     

Controls on the occurrence and prevalence of floodplain channels in meandering rivers

The process of channelization on river floodplains plays an essential role in regulating river sinuosity and creating river avulsions. Most channelization occurs within the channel belt (e.g. chute channels), but growing evidence suggests some channels originate outside of the channel‐belt in the floodplain. To understand the occurrence and prevalence of these floodplain channels we mapped 3064 km² of floodplain in Indiana, USA using 1.5 m resolution digital elevation models (DEMs) derived from airborne light detection and ranging (LiDAR) data. We find the following range of channelization types on floodplains in Indiana: 6.8% of floodplain area has no evidence of channelization, 55.9% of floodplains show evidence (e.g. oxbow lakes) of chute‐channel activity in the channel belt, and 37.3% of floodplains contain floodplain channels that form long, coherent down‐valley pathways with bifurcations and confluences, and they are active only during overbank discharge. Whereas the first two types of floodplains are relatively well studied, only a few studies have recognized the existence of floodplain channels. To understand why floodplain channels occur, we compared the presence of channelization types with measured floodplain width, floodplain slope, river width, river meander rate, sinuosity, flooding frequency, soil composition, and land cover. Results show floodplain channels occur when the fluvial systems are characterized by large floodplain‐to‐river widths, relatively higher meandering rates, and are dominantly used for agriculture. More detailed reach‐scale mapping reveals that up to 75% of channel reaches within floodplain channels are likely paleo‐meander cutoffs. The meander cutoffs are connected by secondary channels to form floodplain channels. We suggest that secondary channels within floodplains form by differential erosion across the floodplain, linking together pre‐existing topographic lows, such as meander cutoffs. Copyright © 2016 John Wiley & Sons, Ltd.     

A model of channel response in disturbed alluvial channels

Dredging and straightening of alluvial channels between 1959 and 1978 in West Tennessee caused a series of morphologic changes along modified reaches and tributary streams. Degradation occurred for 10 to 15 years at sites upstream of the area of maximum disturbance and lowered bed-levels by as much as 6·1 m. Following degradation, reaches upstream of the area of maximum disturbance experienced a secondary aggradation phase in response to excessive incision and gradient reduction. Aggradation downstream of the area of maximum disturbance reached 0·12 m per year with the greatest rates occurring near the stream mouths. The adjustment of channel geometry and phases of channel evolution are characterized by six process-oriented stages of morphologic development—premodified, constructed, degradation, threshold, aggradation, and restabilization. Down-cutting and toe removal during the degradation stage causes bank failure by mass wasting when the critical height and angle of the bank material is exceeded (threshold stage). Channel widening continues through the aggradation stage as the ‘slough line’ develops as an initial site of lower-bank stability. The bank profile develops three dynamic elements (1) vertical face (70° to 90°), (2) upper bank (25° to 50°), and (3) slough line (20° to 25°). Alternate channel bars form during the restabilization stage and represent incipient meandering of the channel.     

The response of headwater stream channels to urbanization in the humid tropics

Analysis of the bankfull cross-sections of headwater streams in Ado-Ekiti region of Southwestern Nigeria and their comparison with data from other tropical environments and temperate latitudes reveal that the channel capacities of streams in the humid tropics are relatively smaller than those of temperate regions, averaging 1.51 m² with a coefficient of variation of 87 per cent. This is attributed to the small stream discharge, the predominantly low and highly seasonal flows of the streams, the low shear stress of stream load, and the stabilizing and protective influence of riparian vegetation and surface incrustations. The chanel capacities of the urban streams (mean = 1.13m²) are about 47 per cent smaller than those of the natural streams (mean = 2.12 m²) in the same ecological zone. In terms of hydraulic efficiency, the urban streams also have relatively inefficient cross-sections and larger width/depth ratios than their rural or natural counterparts. Resurveys of seventeen monumented cross-sections reveal that while channel shoulder width increased by only 6 per cent over a one-year period, channel depth and capacity decreased by 16 per cent and 4 per cent respectively; the observed decrease in channel size occurs entirely in the channel depth dimension. Thus the response of stream channels to the urbanization of small headwater catchments in the humid tropics is probably more of vertical accretion of channel bed and reduction in channel capacity rather than the widely-reported anomalous enlargement of urban streams through channel widening. The rapid rate of channel aggradation is attributed to excessive rates of sediment production and delivery to streams in urbanized catchments in the humid tropics, rapid deposition of sediments during small runoff events and on the falling stage of storm hydrographs, and the inability of the streams to evacuate the sediments delivered to them despite the increased discharge and peak flow associated with urbanization. The low competence of the urban streams is attributed to the predominance of low flows, very gentle bed slopes, and most importantly the widespread dumping of refuse into the channels thereby reducing flow velocity and promoting backwater flooding, ponding, and sedimentation. The correlations between drainage basin area, a surrogate for stream discharge, and channel capacity are very strong for the rural watersheds, and the regression analysis indicates a tendency towards a steady-state isometric relationship. Urban channels are, to a large extent, in disequilibrium with the urban hydrological state. However, spatial variations in the degree of urbanization of the catchments, and, therefore in runoff volume and velocity, exercise strong control on channel width, depth, and size. A model of the sequence of stream channel adjustment to the urbanization of small headwater catchments in the humid tropics is presented.     

The characteristics and significance of some lateglacial protalus ramparts in upland Britain

Arcuate and linear protalus ramparts of inferred Loch Lomond Stadial age are widespread in upland Britain outside the limits of contemporaneous glaciers. Survey and analysis of the morphology of nine ramparts suggests that these may have formed at the foot of slowly thickening snowbeds, with rockfall debris accumulating against their distal slopes, and that snowbed melting at the end of the stadial was uninterrupted by prolonged periods of stability or renewed growth. Rampart sediments consist of poorly-sorted assemblages of clasts with a variable infill of fines. Clast size and shape are strongly influenced by lithology, but rampart clasts are characteristically more angular and ‘slabbier’ than those of similar lithology in ice-marginal moraines. Ramparts may also be distinguished from moraines by their location, morphology, lack of a true matrix of fines and absence of erratics, and from talus-foot rock glaciers in terms of their width and the absence of flow structures. The mapped distribution of rampart altitudes across the Scottish Highlands displays a marked regional trend, with the lowest features in the west and south and highest in the Cairngorms. This pattern mirrors that of reconstructed firn line altitudes of Loch Lomond Stadial glaciers, and is inferred to reflect a pronounced eastwards and northwards decline in snowfall during the stadial.     

Assessment of vegetation effects on hydraulics and of feedbacks on plant survival and zonation in ephemeral channels

The interaction of vegetation and flow in channels is important for understanding the influences of forces in channels and effects on erosion, sediment flux and deposition; it has implications for channel habitats, channel instability and restoration schemes. Methods are needed for calculating forces on plants and data are required on thresholds for plant destruction and survival. A simple method of calculating the effect of hydraulics on vegetation and its zonation within ephemeral channels is described. Detailed cross section surveys of channel morphology, vegetation and estimates of Manning's n are input into the software program WinXSPRO to calculate the hydraulics of flows across the channel for a given event or flow level, incorporating subdivision into zones of differing morphology and vegetation across the section. This was applied to a number of cross sections on ephemeral channels in SE Spain and typical roughness values for Mediterranean vegetation types in channels were assessed. The method is demonstrated with reference to two well‐documented floods in SE Spain, in September 1997 on the Torrealvilla and in October 2003 along the Salada. These flows led to the mortality of herbs, reed and smaller shrub species. Some damage to larger shrubs and trees occurred, but trees such as Tamarisk (Tamarix canariensis) were shown to withstand high forces. Some grasses were highly resistant to removal and induced sedimentation. Significant erosion was limited to areas with little vegetation covering the channel floor. Further quantification of resistance of vegetation to flows and upper threshold values for removal is continuing by relating calculated hydraulic conditions using the methods outlined to measurements of vegetation responses in events at monitoring sites. Copyright © 2009 John Wiley & Sons, Ltd.     

Temporal and spatial behaviour of rip channels in a multiple‐barred coastal system

A 15‐month data set of daily time‐averaged video images (Argus) has been analyzed to describe the spatial and temporal variability of the rip channels on a multiple‐barred coast at Noordwijk aan Zee, The Netherlands. The landward boundary of the intertidal bars and a proxy of the subtidal bar crest, defined as the intertidal and subtidal bar lines respectively, were derived from the Argus images. Local seaward‐directed deviations of the bar lines represent the cross‐shore and alongshore locations of the rip channels. The average intertidal rip spacing ( ) was 243 m, but the rips were not spaced regularly (σ_λ/ = 0.47). Some intertidal rips were observed to fill up during falling tide, but the majority remained open. The filled intertidal rip channels had more landward positions and migrated more slowly (2.4 versus 4.6 m/day) in the alongshore direction than the open intertidal rip channels. The number and the alongshore migration rate of open intertidal rip channels increased with the preceding wave heights (r = 0.26, p < 0.01) and alongshore component of the offshore wave power (r = 0.25, p < 0.01), respectively. The shape of the intertidal bar lines was similar to the subtidal bar line shape, suggesting that the intertidal morphology is coupled to the subtidal alongshore variability. The phase of two bar lines could vary from in phase (0°) to out of phase (180°). The phase changes gradually, due to different alongshore migration rates of the intertidal and subtidal bar lines. Copyright © 2009 John Wiley & Sons, Ltd.     

Width control on event-scale deposition and evacuation of sediment in bedrock-confined channels

In mixed bedrock–alluvial rivers, the response of the system to a flood event can be affected by a number of factors, including coarse sediment availability in the channel, sediment supply from the hillslopes and upstream, flood sequencing and coarse sediment grain size distribution. However, the impact of along-stream changes in channel width on bedload transport dynamics remains largely unexplored. We combine field data, theory and numerical modelling to address this gap. First, we present observations from the Daan River gorge in western Taiwan, where the river flows through a 1 km long 20–50 m wide bedrock gorge bounded upstream and downstream by wide braidplains. We documented two flood events during which coarse sediment evacuation and redeposition appear to cause changes of up to several metres in channel bed elevation. Motivated by this case study, we examined the relationships between discharge, channel width and bedload transport capacity, and show that for a given slope narrow channels transport bedload more efficiently than wide ones at low discharges, whereas wider channels are more efficient at high discharges. We used the model sedFlow to explore this effect, running a random sequence of floods through a channel with a narrow gorge section bounded upstream and downstream by wider reaches. Channel response to imposed floods is complex, as high and low discharges drive different spatial patterns of erosion and deposition, and the channel may experience both of these regimes during the peak and recession periods of each flood. Our modelling suggests that width differences alone can drive substantial variations in sediment flux and bed response, without the need for variations in sediment supply or mobility. The fluctuations in sediment transport rates that result from width variations can lead to intermittent bed exposure, driving incision in different segments of the channel during different portions of the hydrograph. © 2020 The Authors. Earth Surface Processes and Landforms published by John Wiley & Sons Ltd     

Linear and angular momentum conservation in hydraulic jump in diverging channels

This paper addresses the integral conservation of linear and angular momentum in the steady hydraulic jump in a linearly diverging channel.The flow is considered to be divided into a mainstream that conveys the total liquid discharge, and a roller where no average mass transport occurs. It is assumed that no macroscopic rheological relationship holds, so mass, momentum and angular momentum integral balances are independent relationships. Normal stresses are assumed to be hydrostatic on vertical, cylindrical surfaces. Viscous stresses are assumed to be negligible with respect to turbulent stresses. Assuming that the horizontal velocity distribution in the mainstream is uniform and that the horizontal momentum and angular momentum in the roller are negligible with respect to their mainstream counterparts, an analytical solution is obtained for the free surface profile of the flow. This solution is fundamental for finding the sequent depths and their positions. Consequently, it permits solving for the length of the jump, which is assumed to be equal to the length of the roller. Mainstream and roller thicknesses can also be derived from the present solution. This model may also be theoretically used to derive the average shear stresses exerted by the roller on the mainstream and the power losses per unit weight. This second relationship, which returns the well-known classical expression for total power loss in the jump, demonstrates that the strongly idealized mechanical model proposed here is internally consistent.     

Processes and forms of an unstable alluvial system with resistant,cohesive streambeds

As a response to channelization projects undertaken near the turn of the 20th century and in the late 1960s, upstream reaches and tributaries of the Yalobusha River, Mississippi, USA, have been rejuvenated by upstream‐migrating knickpoints. Sediment and woody vegetation delivered to the channels by mass failure of streambanks has been transported downstream to form a large sediment/debris plug where the downstream end of the channelized reach joins an unmodified sinuous reach. Classification within a model of channel evolution and analysis of thalweg elevations and channel slopes indicates that downstream reaches have equilibrated but that upstream reaches are actively degrading. The beds of degrading reaches are characterized by firm, cohesive clays of two formations of Palaeocene age. The erodibility of these clay beds was determined with a jet‐test device and related to critical shear stresses and erosion rates. Repeated surveys indicated that knickpoint migration rates in these clays varied from 0·7 to 12 m a^?1, and that these rates and migration processes are highly dependent upon the bed substrate. Resistant clay beds of the Porters Creek Clay formation have restricted advancement of knickpoints in certain reaches and have caused a shift in channel adjustment processes towards bank failures and channel widening. Channel bank material accounts for at least 85 per cent of the material derived from the channel boundaries of the Yalobusha River system. Strategies to reduce downstream flooding problems while preventing upstream erosion and land loss are being contemplated by action agencies. One such proposal involves removal of the sediment/debris plug. Bank stability analyses that account for pore‐water and confining pressures have been conducted for a range of hydrologic conditions to aid in predicting future channel response. If the sediment/debris plug is removed to improve downstream drainage, care should be taken to provide sufficient time for drainage of groundwater from the channel banks so as not to induce accelerated bank failures. Published in 2002 John Wiley & Sons, Ltd.     

Key morphological changes and their linkages with stream power and land-use changes in the Upper Tapi River basin,India

Knowledge on spatio-temporal variations in planform, hydraulic geometry, and bed-level variations of alluvial streams is required for planning and development of hydraulic structures and bank protection works. In the current study, a Geographic Information System (GIS) has been used to analyze topographical maps, multi-temporal remotely sensed imagery, and hydrologic and hydraulic data to extract the morphological parameters of the Upper Tapi River, India. The river has been found to have consistent migration towards the northern direction, with erosion/deposition on right/left banks. The river has not experienced any major meander except in the lower reaches of the Upper Tapi Gorge and minor braiding conditions at the location where the river emerges from mountainous topography to the plain region. The analyzed river cross sections were found to be depth dominated, and contain large flows within the channel banks. The cross-sections exhibited moderate channel bed adjustments in 1994, 2006, and 2007 wherein excessive sediment flux and stream power were capable of causing morphological changes in the river. High intensity rainfall in the subcatchment resulted in high sediment flux into the river during 1994, which was reported to cause significant aggradation at the downgauging station. The analysis of sediment flux into the river in conjunction with decadal land use land cover, revealed that sediment yield from the catchment was reduced during 2000–2010 due to an increase in water bodies in the form of minor hydraulic structures. The entry of comparatively less sediment laden water into the river, resulted in moderate bed degradation especially in 2006 and 2007 as observed at the downstream station. The methodology applied in the current study is generic in nature and can be applied to other rivers to identify their morphological issues.     

Modelling sediment transport in stream channels in the arid zone of India

Ephemeral channels in arid regions convey larger amounts of sediment than perennial channels in humid regions. Sediment graphs at the outlet of channels have been derived by the standard sediment rating curve technique and by a lumped model based on the instantaneous unit sediment graph (IUSG) concept. The IUSG gives estimates of sediment transport that are better than those derived with the sediment rating curve as it takes into account the availability of erodible material within the channel bed.     

The influence of debris flows on channels and valley floors in the Oregon Coast Range,U.S.A.

Debris flows are one of the most important processes which influence the morphology of channels and valley floors in the Oregon Coast Range. Debris flows that initiate in bedrock hollows at heads of first-order basins erode the long-accumulated sediment and organic debris from the floors of headwater, first- and second-order channels. This material is deposited on valley floors in the form of fans, levees, and terraces. In channels, deposits of debris flows control the distribution of boulders. The stochastic nature of sediment supply to alluvial channels by debris flows promotes cycling between channel aggradation which results in a gravel-bed morphology, and channel degradation which results in a mixed bedrock- and boulder-bed morphology. Temporal and spatial variability of channel-bed morphology is expected in other landscapes where debris flows are an important process.