共查询到20条相似文献,搜索用时 15 毫秒
1.
The deep ocean floor between the Clarion and Clipperton fracture zones (NE equatorial Pacific) has the highest known manganese nodule abundance in the world oceans. A detailed analysis of MR1 (Mapping Researcher 1, 11–12?kHz) sonar images and free-fall grab data in the Korean manganese nodule field areas reveals a close relationship between side-scan sonar characteristics of the seafloor and manganese nodule abundance. Eight sonar facies are identified based on back-scattering intensity and distribution patterns. These sonar facies can be interpreted as (1) volcanic seamounts (facies I-1), (2) bounding faults of abyssal hills (facies I-2 and II-1), (3) lava flows or volcanoclastic mass-flow deposits around the volcanic seamounts (facies I-3 and II-2), (4) crests of abyssal hills (facies II-1), (5) abyssal troughs between abyssal hills (facies III-1), (6) relatively flat areas (facies II-3 and III-2). In the areas where facies II-1 (abyssal hill crests with thin sediment cover) and II-3 (relatively flat areas draped by thin sediments) are dominant, manganese nodules occur abundantly. In contrast, zones comprising facies III-1 (abyssal troughs with thick sediment cover) and III-2 (relatively flat areas covered by thick sediments) are characterized by low abundance of manganese nodules. This relationship between distribution of sonar facies and manganese nodule abundance implies that (1) the qualitative difference in acoustic reflectivity of long-range side-scan sonar with some ground truth data is useful for regional assessment of manganese nodule occurrence over wide areas in a reasonable time, and (2) seafloor topography and sediment thickness are important controlling factors for regional occurrences of manganese nodules. 相似文献
2.
Hoi-Soo Jung Young-Tak Ko Sang-Bum Chi Jai-Woon Moon 《Marine Georesources & Geotechnology》2001,19(3):167-180
Seafloor morphology and ferromanganese nodule occurrence were studied using a multibeam side scan sonar (SeaBeam, 2000) and a deep-sea camera system in the Korea Deep-sea Environmental Study (KODES) area, northeast equatorial Pacific. Seafloor morphology and nodule abundance are highly variable even in this small study area. The NNE-SSW oriented hills are parallel and about 100-200 m high. Valleys are very flat-floored, while hilltops are rugged with depressions of tens of meters. Cliffs to about 100 m bound the valleys and the hills. The study area can be classified into three types based both on nodule occurrence and seafloor morphology, mostly G- and B-types and some M-type. G-type is characterized by high nodule abundance, ubiquitous bioturbation, and flat seafloor morphology, while B-type is characterized by irregular-shaped nodules, variable nodule abundance, occurrence of giant nodules and sediment lumps, rugged bottom morphology with depressions, and white calcareous surface sediments. Medium nodule abundance and a generally flat seafloor characterize M-type. G-type occurs mostly in the valley regions, while B-type is on the hilltop areas. M-type is located between the hilltop and the valley. Tectonic movement of the Pacific plate resulted in the elongated abyssal hills and cliffs. The rugged morphology on hilltops resulted from erosion and redistribution of surface siliceous sediments on hilltops by bottom currents, outcropping of underlying calcareous sediments, and dissolution of the carbonate sediments by corrosive bottom water undersaturated with CaCO 3 . Sediment eroded from the hills, which is relatively young and organic-rich, is deposited in the valleys, and diagenetic metal supply to manganese nodules in the valley area is more active than on the hills. We suggest that tectonic movement ultimately constrains morphology, surface sediment facies, bottom currents and sediment redistribution, bioturbation, thickness of the sedimentary layer, and other conditions, which are all interrelated and control nodule occurrence. The best potential area for mining in the study area is the G-type valley zones with about 3-4 km width and NNW-SSE orientation. 相似文献
3.
Hoi-Soo Jung Young-Tak Ko Sang-Bum Chi Jai-Woon Moon 《Marine Georesources & Geotechnology》2013,31(3):167-180
Abstract Seafloor morphology and ferromanganese nodule occurrence were studied using a multibeam side scan sonar (SeaBeam, 2000) and a deep-sea camera system in the Korea Deep-sea Environmental Study (KODES) area, northeast equatorial Pacific. Seafloor morphology and nodule abundance are highly variable even in this small study area. The NNE-SSW oriented hills are parallel and about 100–200 m high. Valleys are very flat-floored, while hilltops are rugged with depressions of tens of meters. Cliffs to about 100 m bound the valleys and the hills. The study area can be classified into three types based both on nodule occurrence and seafloor morphology, mostly G- and B-types and some M-type. G-type is characterized by high nodule abundance, ubiquitous bioturbation, and flat seafloor morphology, while B-type is characterized by irregular-shaped nodules, variable nodule abundance, occurrence of giant nodules and sediment lumps, rugged bottom morphology with depressions, and white calcareous surface sediments. Medium nodule abundance and a generally flat seafloor characterize M-type. G-type occurs mostly in the valley regions, while B-type is on the hilltop areas. M-type is located between the hilltop and the valley. Tectonic movement of the Pacific plate resulted in the elongated abyssal hills and cliffs. The rugged morphology on hilltops resulted from erosion and redistribution of surface siliceous sediments on hilltops by bottom currents, outcropping of underlying calcareous sediments, and dissolution of the carbonate sediments by corrosive bottom water undersaturated with CaCO3. Sediment eroded from the hills, which is relatively young and organic-rich, is deposited in the valleys, and diagenetic metal supply to manganese nodules in the valley area is more active than on the hills. We suggest that tectonic movement ultimately constrains morphology, surface sediment facies, bottom currents and sediment redistribution, bioturbation, thickness of the sedimentary layer, and other conditions, which are all interrelated and control nodule occurrence. The best potential area for mining in the study area is the G-type valley zones with about 3–4 km width and NNW-SSE orientation. 相似文献
4.
During RV SONNE cruise SO-79 to the eastern Pacific Ocean, two areas of about 65×80 km in the northern Peru Basin were surveyed with the acoustic mapping systems HYDROSWEEP (bathymetry), PARASOUND (3.5 kHz high-resolution seismic system), and a deep-towed side-scan sonar system. In addition, we sampled sediments using piston and box corers. The data show an unexpected variability of seafloor features: The bathymetry is characterized by an abyssal hill topography with predominately N-S ridges up to 300 m high, and scattered volcanic hills. Moreover, one 2000-m-high seamount was mapped. PARASOUND shows several distinct reflectors within the sediment cover, all of which are attributed to carbonate-rich strata. In the northern area, the uppermost prominent reflector is related to the Mid-Brunhes Event (0.45 Ma) in the sediment cores, while the lowermost represents acoustic basement. In the southern area, the seismic pattern reveals an upper opaque zone and a lower transparent zone. The base of the opaque zone is marked by a distinct reflector which corresponds to a huge carbonate peak (6–7 Ma) in the sediment cores. However, despite this general pattern, the PARASOUND records show a highly variable situation, with the distribution of sediment echo types strongly influenced by the seafloor topography. The side-scan sonar revealed the existence of numerous small volcanic cones up to 25 m high and nearly free of sediment. Additionally, the sonar records show a patchy (up to 800 m across) seafloor reflectiviti. We interpret this patchiness as a local lack of manganese nodule coverage. Volcanic cones and the most distinct nodule-free patches are usually on ridges. We interpret this variability as caused by winnowing and erosion, an interpretation that is supported by the occurrence of outcrops of Tertiary strata. This regional small-scale variability argues for a highly dynamic depositional history of the Peru Basin. 相似文献
5.
Chan Min Yoo Jongmin Joo Sang Hoon Lee Youngtak Ko Sang-Bum Chi Hyung Jeek Kim Inah Seo Kiseong Hyeong 《Ocean Science Journal》2018,53(2):381-394
A high level of confidence in resource data is a key prerequisite for conducting a reliable economic feasibility study in deep water seafloor mining. However, the acquisition of accurate resource data is difficult when employing traditional point-sampling methods to assess the resource potential of polymetallic nodules, given the vast size of the survey area and high spatial variability in nodule distribution. In this study, we analyzed high-resolution acoustic backscatter intensity images to estimate nodule abundance and increase confidence levels in nodule abundance data. We operated a 120 kHz deep-towed sidescan sonar (DSL-120) system (1×1 m resolution) across a 75 km2 representative area in the Korean Exploration Area for polymetallic nodules in the Northeastern Equatorial Pacific. A deep-towed camera system was also run along two tracks in the same area to estimate the abundance of polymetallic nodules on the seafloor. Backscatter data were classified into four facies based on intensity. The facies with the weakest and strongest backscatter intensities occurred in areas of high slope gradient and basement outcrops, respectively. The backscatter intensities of the two other facies correlated well with the nodule abundances estimated from still-camera images. A linear fit between backscatter intensity and mean nodule abundance for 10 zones in the study area yielded an excellent correlation (r2 = 0.97). This allowed us to compile a map of polymetallic nodule abundance that shows greater resolution than a map derived from the extrapolation of point-sampling data. Our preliminary analyses indicate that it is possible to greatly increase the confidence level of nodule resource data if the relationship between backscatter intensity and nodule abundance is reliably established. This approach has another key advantage over point sampling and image analyses in that detailed maps of mining obstacles along the seafloor are produced when acquiring data on the abundance of polymetallic nodules. The key limitation of this work is a poor correlation between nodule coverage, as observed from photographs, and nodule abundance. Significant additional ground truth sampling using well located box cores should be completed to determine whether or not there is a real correlation between the backscatter and abundance. 相似文献
6.
Thomas F. Wever Hannelore M. Fiedler Gunther Fechner Friedrich Abegg Ingo H. Stender 《Geo-Marine Letters》1997,17(4):246-252
Between 2 and 6 February, 1995, a 25 km2 area at the Dry Tortugas (Florida Keys) was surveyed with a 100 kHz side-scan sonar system and 3.5-kHz subbottom profiler.
The side-scan system revealed a pattern of alternating high and low backscatter. The subbottom profiler showed areas with
no acoustic penetration between sediment troughs. The combination of both methods allowed delineation of the boundaries in
high-backscatter regions, and sediment samples allowed correlations between high backscatter and coarser-grained sediments. 相似文献
7.
Mahatma Lanuru Rolf Riethmüller Carlo van Bernem Kerstin Heymann 《Estuarine, Coastal and Shelf Science》2007,72(4):603-614
The erosion potential over bedforms in a tidal flat of the East Frisian Wadden Sea was studied by conducting erosion and physical and biological sediment property measurements on the crests and troughs of bedforms. Five stations along a cross-shore transect of 1.5 km length from immediately below the salt marsh to the mid tide-level of the tidal flat were visited during two field campaigns in June and September 2002. Measurements of sediment erodibility were made on both crests and troughs using an EROMES erosion device and quantified in terms of critical erosion shear stress and erosion rate. Surface sediment scrape samples (upper 1 mm layer) were taken from crests and troughs to determine various physical and biological properties of the sediment. The results show that crests are generally more stable (i.e. higher critical erosion shear stresses and lower erosion rates) than troughs. In general, crests contained more chlorophyll a, colloidal carbohydrate, and EPS (extracellular polymeric substance) than troughs. Median grain-size, water content and wet bulk density of the crests showed no statistically significant difference from those of the troughs with the exception at the most landward station immediately below the salt marsh margin, where crests had significantly lower water content and higher wet bulk density than troughs.Two different processes were identified for the difference in erodibility between crests and troughs: (1) At stations with emersion times less than 6 h, the higher benthic diatom biomass (measured as chlorophyll a concentration) on the crests increases the amount of EPS, which is likely to stabilize the sediment surface of these features; (2) in a saltmarsh transition area (most landward station), physical processes such as surface drying and compaction seem to enhance in a synergistic way the sediment stability on the crests. 相似文献
8.
Quantitative estimation of seafloor features from photographs and their application to nodule mining
Rahul Sharma 《Marine Georesources & Geotechnology》2013,31(4):311-331
Methods developed for quantitative estimation of seafloor features from seabed photographs and their application for estimation of nodule sizes, coverage, abundance, burial, sediment thickness, extent of rock exposure, density of benthic organisms, and their lebensspuren have been presented. Digitization of the photographs shows variable nodule size (< 1 to 10 cm), coverage (< 1 to 75%) and abundance (< 1 to 20 kg/m2). Nodule population is inversely proportional to the coverage of the sediment (10–100%) and its thickness (0 to > 10 cm), which causes differential burial (0–100%) of nodules. Correlation between nodule parameters (diameter and coverage) in the photographs and grab recovery is used to evolve empirical relationships for estimating nodule abundance in different seabed settings. The rock outcrops (basalts) with a coverage of 6–100% are the sources of nuclei for the nodules, the distribution of which is controlled by the local topography. Higher concentrations of nodules are observed along the slopes, followed by the crests of seamounts, and are lowest in the valleys and plains. A population density of 6–7 benthic organisms per 100 m2 belonging to 7 different phyla is observed, with a high frequency of lebensspuren (4–12 traces/m2) in association with nodules. Estimation of these parameters can be used as important inputs in the design of the nodule collector, as it will have to encounter a variety of seafloor conditions, such as patchy nodule distribution, rock outcrops, steep slopes, and frequent microtopographic changes, as well as benthic life. The distribution and relation of various features with one another can also be used to understand the possible impact of nodule mining on the seabed. Estimates show that for a yield of 3 million tonnes of nodules per year, the volume of sediment disturbed will be between 200 × 107 and 500 × 107 m3over an area of 300–600 km2, depending upon the average abundance of nodules. Hence, the nodule collector will have to be a self‐propelled system, with photographic and acoustic sensors, to enable selective mining and avoid unfavorable areas. 相似文献
9.
Application of quantitative angular backscatter modelling to manganese nodule-bearing areas of the Central Indian Ocean Basin (CIOB) has been initiated at NIO during the year 1998. Studies were aimed to establish the suitability of seafloor backscattering in delineating seafloor parameters characteristic of nodule-rich sediments. In this paper, processed Hydrosweep multi-beam backscatter data from 45 spot locations in the CIOB (where nodule samples are available) were analysed to estimate seafloor and sediment volume roughness parameters. The application of a composite roughness model to a nodule-bearing region (6,600 km2) of the CIOB, to determine seafloor interface roughness parameters from a multi-beam backscatter dataset, shows only four power law sets. The results attest 80% of the nodule-bearing seafloor to be smooth in terms of interface roughness parameters at micro-topographic level. The sediment volume roughness parameters are dominant only in 29% of the smooth interface roughness sites. This indicates that 51% of the seafloor area possesses negligible (interface and volume) roughness. A critical analysis using pseudo-side-scan records from 12 selected locations in the study area affirms the combined importance of the seafloor interface and sediment volume roughness parameters for precise determination of manganese nodule abundance. 相似文献
10.
The I.O.S. long range side-scan sonar GLORIA has been widely used over a variety of seabed types, but until recently had not been used over an independently authenticated field of manganese nodules. In the Eastern Atlantic Ocean at approximately 31°25 N 25°15 W, a field of nodules approximately 3–6 cm in diameter covering up to 18% of the seafloor was observed using an underwater camera. The nodule field occurred over approximately 2.8 km of the 8.3 km camera run. The corresponding GLORIA image shows an area of medium intensity backscattering, approximately 3.7 km in diameter. Considering the likely contrast in acoustic reflectivity between manganese nodules and deep sea sediments, we propose a correlation between the nodules observed in the photographs and the medium intensity echo target revealed by the GLORIA system. 相似文献
11.
Manganese nodule distribution is primarily influenced by seafloor topography. Nodule distribution at 479 locations vis‐à‐vis seabed topography is studied by superimposing sampling location on the topographic profile and assigning appropriate domain (hilltop, valley, slope, or plain) for the sampling location. Highest mean abundance is observed at the valleys (6.94 kg /m2), followed by hilltops, slopes, and least on plains. Frequency distributions are regular (Gaussian) on plains, whereas on valleys and hilltops they are irregular (Rayleigh type). Fe and Co content is highest in nodules from hilltops and lowest in those from plains. Conversely, Mn, Cu, and Ni content is highest on plains and least on valleys. Fe: Mn and Co: Mn are negatively correlated in all the domains. Mn and total metal content (Ni + Cu + Co) show direct relationship in all the domains. An inverse relation between nodule abundance and composition is found. Cluster analysis on chemical and abundance data shows two distinct groups in all domains. Abundance and Fe and Co content typically form one group, while all other elements form another group. Genesis of nodules depends on the availability of supply of transition elements to the abyssal environment, maintenance of nodules in the sediment‐water interface, and sedimentation rates. 相似文献
12.
Polymetallic nodule and sediment characteristics were investigated for two blocks (KR2 and KR5) in the Korea Deep Ocean Study (KODOS) area in order to better understand nodule distribution and the potential effects of sediments on nodule genesis. The northern block (KR2) is dominated by hydrogenetic nodules, whereas the southern block (KR5) is dominated by diagenetic nodules. Sediments in the study area are assigned to three major lithologic units which are distinctive in color and texture. The northern block is characterized by a thick, metalpoor Unit 1 sediment, which is thin in the southern block, where metal-rich Units 2b and 3 occur close to the surface. The distribution of different nodule genetic types in the northern and southern blocks can be attributed to topographic variations (topographic high near seamounts in KR2 and abyssal plain in KR5) and different sedimentation rates (0.1 and 0.32 mm/kyr in blocks KR2 and KR5, respectively). The southern block has a geologic setting more conducive to diagenetic nodule formation, such as flat topography and sediment composition. Nodule distribution in the studied blocks might also be explained by the distribution of the sediment units of different metal contents. The northern block, in which Unit 1 is thicker, has more abundant hydrogenetic nodules, possibly because Unit 1 prevents metals that are remobilized from the underlying sediments from reaching the seabed where the nodules are forming. 相似文献
13.
Optimum sampling interval for evaluating ferromanganese nodule resources in the central Indian Ocean
A study to estimate manganese nodule abundance (weight of nodules in kg/m2) was carried out in a small area of the abyssal plains covering a one-degree square block in the central Indian Basin. Abundance was assessed at various intervals by progressively reducing the grid spacing. Sampling the corners of the 1° survey block (approximately110-km spacing), i.e., four stations with 5-7 free-fall operations (sampling locations) in each case, indicated a nodule abundance of 3.50 kg/m2. By reducing the sampling spacing to four grid units (0.5° survey blocks) and sampling the entire block at eight stations (25 locations), the average abundance of the block was 3.36 kg/m2. Further reduction of the grid to 0.25° survey blocks and sampling in 16 grid units (70 sampling locations) increased the abundance to 4.41 kg/m2. For 64 grid units in the one-degree block (sampling in 0.125° survey blocks), a substantially higher value was recorded, i.e., 5.31 kg/m2 or about 1.5 times the abundance obtained at a 1° spacing. Adding 25 more stations in 0.0625° survey blocks (intervals of sampling locations approximately 500 m) resulted in a negligible change in abundance, the average value of the one-degree block being 5.23 kg/m2. These data demonstrate that, for estimating nodule resources in the region, it is important to adopt a close-grid sampling strategy, so that areas with lower abundance can be relinquished and areas with higher abundance can be confidently identified. To ascertain exact nodule abundance for mine-track selection, it may be sufficient to restrict detailed grid surveys to areas with marked variations in topography and nodule abundance, rather than carrying out such detailed (albeit less cost effective) surveys at a very narrow spacing (0.0625°) over the entire pioneer area. 相似文献
14.
Distribution characteristics of cobalt‐rich manganese deposits were evaluated from stereo photographs and video data on a seamount in the central Pacific Ocean by image analysis, photogrammetric technique, and visual observations. The results show that many locations have high crust coverages with highly undulating micro‐topography. High nodule coverages occur on relatively flat seafloor, and the nodule size distribution varies from uniform to inhomogeneous among different locations. Distribution of these deposits along detailed topographic sections show that the seafloor can be divided into nodule dominant zones between 0° and 3° slopes, with sediment patches up to 4° slopes; and crust dominant zones, which occur on slopes higher than 15°. The transition zone, between 4° and 15° slopes, has many locations, where nodules and crusts co‐occur in varying percentages. The observation of crust outcrops among sediments and nodules, as well as in the gravity core samples, indicates the presence of shallow buried crusts as well, which can substantially enhance resource evaluation of the deposits. 相似文献
15.
High-resolution multi-beam/single-beam bathymetric data and seismic profiling data from the latest surveys are used to map and interpret the detailed seafloor geomorphology of the western region of the North Yellow Sea (NYS), China. The mapping area covers 156 410 km2, and incorporates a flat shelf plain, subaqueous accumulation shoals, tidal scouring troughs, and tidal sand ridge groups. Offshore areas with water depths less than 50 m in the western region of the NYS are mainly covered by thick, loose sediments, forming wide spread accumulation geomorphological features; these include the Liaodong Peninsula subaqueous accumulation system containing shoals and rugged scouring troughs, and the large mud wedge of the Shandong Peninsula. In the central part of the NYS, there is a relatively flat residual shelf plain with coarser sediment deposits. This flat shelf plain has a water depth larger than 50 m and a thin layer of sediment, on which there is a large pockmark field caused by seafloor seepage. These geomorphological structures indicate that modern sedimentary processes are the main driving force controlling the sculpture of the current seafloor surface landform. Extensive strong tidal current systems and abundant sediment sources provide the critical external forces and essential conditions for the formation of seafloor geomorphology. The tectonic basement controls the macroscopic morphological shape of the NYS, but is reflected very little in the seafloor geomorphic elements. Our results provide a detailed seafloor geomorphological map of the western region of the NYS, an area that has not previously mapped and also provide a scientific framework for further research into offshore seafloor geomorphology, shelf sedimentary processes, and submarine engineering construction in this region. 相似文献
16.
海南岛东南外海海底沉积物特征及其声学物理性质研究 总被引:3,自引:1,他引:2
分析研究了南海北部大陆架西南缘的海南岛东南外海海底沉积物声学物理特性,在多个航次中进行了海底沉积层取样、海水CTD测量、浅地层及旁侧声呐扫测等工作.在实验室里对沉积物样品进行声学参数、沉积学基本参数、物理力学参数和14C年龄测试等分析.根据多尔特曼公式求解出弹性模量、体积弹性模量、压缩系数、切变模量、泊松比和拉梅常数等六项沉积物弹性参数.分析结果表明在该海区海底沉积物的压缩波速为1.474~1.700 m/s,在不同的海区内有高低声速两类性质的沉积物分布;沉积物的切变波速为150~600 m/s;沉积物在100 kHz的声衰减为35~260 dB/m;沉积物的密度为1.4~2.0 g/cm3;沉积物的孔隙度为42%~88%. 相似文献
17.
Morphological Features of Co-Rich Manganese Deposits and Their Relation to Seabed Slopes 总被引:7,自引:0,他引:7
The morphological features associated with Co-rich manganese deposits, the size variations of nodules, and the occurrence of different substrates have been analyzed, to evaluate the influence of various seabed slope angles on the distribution of these features. The coverage and size of the crusts depend on their surface morphology and seabed topography, resulting in cobble-type, lineated, or step-like outcrops. Small nodules (1 - 4 cm in diameter) dominate all seabed slopes, with a few locations having nodules ranging from 1 to 8 or 1 to 10 cm. Sediments invariably occur as substrates for nodules and as cover for crusts, their coverage being inversely proportional to that of the nodules and crust outcrops. Steeper seafloor areas have large crust outcrops exposed with no or few nodules and sediments associated with them. The intermediate slopes have a combination of nodules, sediments, and crusts in various proportions, depending on topography and gradient. Large-scale nodule occurrences, followed by sediment fields and crust outcrops on seabed slopes of greater than 3 degrees, 3 - 7 degreees, and less than 15 degrees, respectively, represent typical morphological distribution zones of the Co-rich manganese deposits on a seamount in the central Pacific Ocean. A transition zone between nodule-dominated fields and large crust outcrops occurs for slopes from 7 degrees to 15 degrees. This detailed study on distribution of Co-rich deposits gives a better understanding for purposes of their exploitation. 相似文献
18.
A 250 km2 area of abyssal hills in the vicinity of 14°N, 126°W (between the Clarion and Clipperton Fracture Zones in the Equatorial Pacific) was surveyed in detail using an instrument package towed close to the deep sea floor, the MPL Deep Tow device. Both topography and near bottom magnetic field are lineated perpendicular to the major fracture zones. Except for a few localized depressions, the sediment surface is generally smooth and of low relief with maximum elevation differences of 200 m and slopes of six degrees. Several small graben-like troughs and depressions were observed, most of them near the crest of one abyssal hill. The largest trough is two kilometers long, 250 m wide and 50 m deep with steep sides (>30°). These troughs are tentatively interpreted as the result of tensional separation at the tops of the hills caused by down-slope creep and consolidation of the pelagic sediments.Contribution of the Scripps Institution of Oceanography, new series. 相似文献
19.
In the Central Indian Basin manganese nodule abundance was variable in all sediment types. Mean abundance varied from 1.5 in calcareous ooze to 10.2 kg/m2 in terrigenous-siliceous ooze sediments. Nodule grade and growth rates are positively correlated only up to 10 mm/My (million years), and grade shows no distinct relationship with abundance. Relationships between the morphochemical characteristics of the nodules and host sediment types are subtle. Both hydrogenetic and diagenetic nodules (with smooth and rough surfaces respectively) occur on almost all sediments, but in variable proportions. Thus, the overall distribution pattern shows that small nodules (<4-cm diameters) of lower grade (average value Ni+Cu+Co=1.21%) with smooth surfaces are more common on red clay, terrigenous, and terrigenous-siliceous ooze transition-zone sediments. By contrast, large nodules (>4-cm diameters) of higher grade (average value Ni+Cu+Co=1.80%) with rough surfaces are more prevalent on siliceous ooze, siliceous ooze-red clay, and calcareous ooze-red clay transition-zone sediments. This implies an enhanced supply of trace metals from pore waters to rough-surface nodules during early diagenesis. 相似文献
20.
The Mediterranean Ridge is an arcuate ridge of deformed sediment caught up in the convergent plate margin between the African plate and the Aegean. An intensive campaign of SeaMARC I and SeaBeam surveys followed by piston coring has been conducted along the contact between undeformed turbidites of the Sirte Abyssal Plain and folded and faulted sediments of the Mediterranean Ridge. Along the outer edge of the Ridge, surficial sediments have been deformed into sinusoidal ridges and troughs (wavelengths 0.5–2 km, amplitude 20–150 m), which we interpret as folds. In plan view, the ridge and the trough fabric parallels the NW-SE trending regional contours, suggesting that the folds formed in response to compression orthogonal to the Mediterranean Ridge. The outermost ridge is shedding a debris apron out onto the abyssal plain, implying that uplift and deformation are ongoing. We show that the geometry of the outermost folds can be produced by elastic bending of a packet of 5–10 relatively strong layers, each 10–20 m thick, interbedded between weaker layers; we equate the strong layers with gypsum beds in the Messinian upper evaporites. Folding the seafloor from a flat layer into the observed ridge and trough topography would shorten the layer by less than 2%. Two percent shortening (equals two percent thickening) is insufficient to create the observed relief of the Mediterranean Ridge even if the entire sediment column down to basement were involved; we infer that additional shortening/thickening is accommodated by thrust faulting above a decollement at the top of the Messinian salt layer. At distances > 15 km from the deformation front and more than 500 m from the abyssal plain, sharp-edged, fine-grained side-scan lineations with very little vertical relief cut across the kilometer-scale ridge and trough topography. These fine-grained lineations fall in two groups trending N/S to NNE/SSW and ~ENE. We interpret these lineaments as traces of conjugate strike-slip faults formed in the same compressional regime which formed the NW/SE trending folds. The onset of strike-slip faulting may coincide with the cessation of imbricate thrust fan development above the initial salt-controlled decollement surface. The following characteristics of the Mediterranean Ridge are attributed to the presence of evaporites in the incoming sedimentary section: (1) initial deformation by folding rather than thrust faulting; (2) narrow taper; (3) rapid rate of outward growth; (4) karstification. 相似文献