A Finite Layer Formulation for Groundwater Flow to Horizontal Wells

A finite layer approach for the general problem of three‐dimensional (3D) flow to horizontal wells in multilayered aquifer systems is presented, in which the unconfined flow can be taken into account. The flow is approximated by an integration of the standard finite element method in vertical direction and the analytical techniques in the other spatial directions. Because only the vertical discretization is involved, the horizontal wells can be completely contained in one specific nodal plane without discretization. Moreover, due to the analytical eigenfunctions introduced in the formulation, the weighted residual equations can be decoupled, and the formulas for the global matrices and flow vector corresponding to horizontal wells can be obtained explicitly. Consequently, the bandwidth of the global matrices and computational cost rising from 3D analysis can be significantly reduced. Two comparisons to the existing solutions are made to verify the validity of the formulation, including transient flow to horizontal wells in confined and unconfined aquifers. Furthermore, an additional numerical application to horizontal wells in three‐layered systems is presented to demonstrate the applicability of the present method in modeling flow in more complex aquifer systems.     

Performance of the steady-state dipole flow test in layered aquifers

Steady-state numerical simulations of the dipole flow test in layered aquifers demonstrate that the test produces a good estimate of the equivalent hydraulic conductivity anisotropy ratio for the part of the aquifer spanned by the well chambers. The effects of chamber size, different conductivity of layers and layer location on the estimated anisotropy ratios are presented. The steady-state dipole flow test, when performed at different levels in the well, can yield estimates of the down-hole anisotropy ratio distribution. Numerical simulations also illustrate that the skin effect can significantly distort the anisotropy estimates produced by the dipole flow test. © 1997 John Wiley & Sons, Ltd.     

A new analytical solution solved by triple series equations method for constant-head tests in confined aquifers

The constant-head pumping tests are usually employed to determine the aquifer parameters and they can be performed in fully or partially penetrating wells. Generally, the Dirichlet condition is prescribed along the well screen and the Neumann type no-flow condition is specified over the unscreened part of the test well. The mathematical model describing the aquifer response to a constant-head test performed in a fully penetrating well can be easily solved by the conventional integral transform technique under the uniform Dirichlet-type condition along the rim of wellbore. However, the boundary condition for a test well with partial penetration should be considered as a mixed-type condition. This mixed boundary value problem in a confined aquifer system of infinite radial extent and finite vertical extent is solved by the Laplace and finite Fourier transforms in conjunction with the triple series equations method. This approach provides analytical results for the drawdown in a partially penetrating well for arbitrary location of the well screen in a finite thickness aquifer. The semi-analytical solutions are particularly useful for the practical applications from the computational point of view.     

Leaky Aquifer Models to Simulate the Well Flow in Fractured Aquifers with Linear Interporosity Flow

Following Hemker and Maas (1987) the models of two or three leaky aquifers are applied to simulate the flow to vertical wells operating in the fractured or dual porosity aquifers. The software WellTest (WT) (Székely 2015) is used for calculating the drawdown and discharge rate variation. The comparative analysis with the independent analytical solutions by Boulton and Streltsova-Adams (1978), Warren and Root (1963), Kazemi et al. (1969) concluded with acceptable agreement between the WT simulation and the alternate calculation methods. The selected field tests have been conducted in fractured limestone aquifers. The pumping test west of Copenhagen shows an example of fractured aquifer with considerable negative skin effect at the well face. The flowing well Wafra W1 in Kuwait operates in the two-zone aquifer exhibiting sufficient vertical recharge via leakage beyond a circular domain of estimated radius of 2460 m.     

Boundary depletion rate and drawdown in leaky wedge‐shaped aquifers

This study presents analytical solutions of the three‐dimensional groundwater flow to a well in leaky confined and leaky water table wedge‐shaped aquifers. Leaky wedge‐shaped aquifers with and without storage in the aquitard are considered, and both transient and steady‐state drawdown solutions are derived. Unlike the previous solutions of the wedge‐shaped aquifers, the leakages from aquitard are considered in these solutions and unlike similar previous work for leaky aquifers, leakage from aquitards and from the water table are treated as the lower and upper boundary conditions. A special form of finite Fourier transforms is used to transform the z‐coordinate in deriving the solutions. The leakage induced by a partially penetrating pumping well in a wedge‐shaped aquifer depends on aquitard hydraulic parameters, the wedge‐shaped aquifer parameters, as well as the pumping well parameters. We calculate lateral boundary dimensionless flux at a representative line and investigate its sensitivity to the aquitard hydraulic parameters. We also investigate the effects of wedge angle, partial penetration, screen location and piezometer location on the steady‐state dimensionless drawdown for different leakage parameters. Results of our study are presented in the form of dimensionless flux‐dimensionless time and dimensionless drawdown‐leakage parameter type curves. The results are useful for evaluating the relative role of lateral wedge boundaries and leakage source on flow in wedge‐shaped aquifers. This is very useful for water management problems and for assessing groundwater pollution. The presented analytical solutions can also be used in parameter identification and in calculating stream depletion rate and volume. Copyright © 2011 John Wiley & Sons, Ltd.     

Hydraulics of a partially penetrating well with skin zone in a confined aquifer

A steady/quasi-steady model is developed for predicting flow into a partially penetrating well with skin zone in a confined aquifer overlying an impervious layer. The model takes into account flow through the bottom of the wellbore, finite skin thickness and finite horizontal and vertical extent of the aquifer. Moreover, the solution can be easily extended to include the mixed-type boundary condition at the well face, where a Dirichlet in the form of a specified hydraulic head and a Neumann in the form of zero flux coexist at the same time at different portions of the well face. The validity of the proposed solution is tested by comparing a few results obtained from the developed model with corresponding results obtained by analytical and numerical means. The study shows that, among other factors remaining constant, both the horizontal and vertical extent of an artesian aquifer, thickness of the skin zone, bottom flow and conductivity contrast of the skin and formation zones, play an important part in deciding flow to a well dug in the aquifer, and hence these factors must be considered while analyzing the problem. The model proposed here can be used to estimate skin thickness as well as hydraulic conductivities of the skin and formation zones of a well with skin zone in an artesian aquifer underlain by an impervious layer by utilizing pumping test data falling in the steady or quasi-steady state of a typical pumping test. As the proposed solution is of a general nature in the sense that it can handle, apart from partial penetration and bottom flow, the finite size skin zone and finite horizontal and vertical extent of an artesian aquifer together with the mixed-type boundary condition at the well face, it is hoped that the predictions coming out of the model will be more realistic than those obtained using solutions developed with more stringent assumptions.     

Recent advances in modeling of well hydraulics

Well hydraulics is a discipline to understand the process of flow to the well in an aquifer which is regarded as a source of groundwater. A variety of analytical and numerical models have been developed over the last few decades to provide a framework for understanding and quantifying the flow behavior in aquifer systems. In this review, we first briefly introduce the background of the theory of well hydraulics and the concepts, methodologies, and applications of analytical, semi-analytical, numerical and approximate methods in solving the well-hydraulic problems. We then address the subjects of current interests such as the incorporation of effects of finite well radius, wellbore storage, well partial penetration, and the presence of skin into various practical problems of groundwater flow. Furthermore, we also summarize recent developments of flow modeling such as the flow in aquifers with horizontal wells or collector wells, the capture zone delineation, and the non-Darcian flow in porous media and fractured formations. Finally, we present a comprehensive review on the numerical calculations for five well functions frequently appearing in well-hydraulic literature and suggest some topics in groundwater flow for future research.     

Three-dimensional semi-analytical solution to groundwater flow in confined and unconfined wedge-shaped aquifers

The Laplace domain solutions have been obtained for three-dimensional groundwater flow to a well in confined and unconfined wedge-shaped aquifers. The solutions take into account partial penetration effects, instantaneous drainage or delayed yield, vertical anisotropy and the water table boundary condition. As a basis, the Laplace domain solutions for drawdown created by a point source in uniform, anisotropic confined and unconfined wedge-shaped aquifers are first derived. Then, by the principle of superposition the point source solutions are extended to the cases of partially and fully penetrating wells. Unlike the previous solution for the confined aquifer that contains improper integrals arising from the Hankel transform [Yeh HD, Chang YC. New analytical solutions for groundwater flow in wedge-shaped aquifers with various topographic boundary conditions. Adv Water Resour 2006;26:471–80], numerical evaluation of our solution is relatively easy using well known numerical Laplace inversion methods. The effects of wedge angle, pumping well location and observation point location on drawdown and the effects of partial penetration, screen location and delay index on the wedge boundary hydraulic gradient in unconfined aquifers have also been investigated. The results are presented in the form of dimensionless drawdown-time and boundary gradient-time type curves. The curves are useful for parameter identification, calculation of stream depletion rates and the assessment of water budgets in river basins.     

Dynamic response of a multi-layered poroelastic medium

An exact stiffness matrix method is presented to evaluate the dynamic response of a multi-layered poroelastic medium due to time-harmonic loads and fluid sources applied in the interior of the layered medium. The system under consideration consists of N layers of different properties and thickness overlying a homogeneous half-plane or a rigid base. Fourier integral transform is used with respect to the x-co-ordinate and the formulation is presented in the frequency domain. Fourier transforms of average displacements of the solid matrix and pore pressure at layer interfaces are considered as the basic unknowns. Exact stiffness (impedance) matrices describing the relationship between generalized displacement and force vectors of a layer of finite thickness and a half-plane are derived explicitly in the Fourier-frequency space by using rigorous analytical solutions for Biot's elastodynamic theory for porous media. The global stiffness matrix and the force vector of a layered system is assembled by considering the continuity of tractions and fluid flow at layer interfaces. The numerical solution of the global equation system for discrete values of Fourier transform parameter together with the application of numerical quadrature to evaluate inverse Fourier transform integrals yield the solutions for poroelastic fields. Numerical results for displacements and stresses of a few layered systems and vertical impedance of a rigid strip bonded to layered poroelastic media are presented. The advantages of the present method when compared to existing approximate stiffness methods and other methods based on the determination of layer arbitrary coefficients are discussed.     

Periodic forcing in composite aquifers

Observations of periodic components of measured heads have long been used to estimate aquifer diffusivities. The estimations are often made using well-known solutions of linear differential equations for the propagation of sinusoidal boundary fluctuations through homogeneous one-dimensional aquifers. Recent field data has indicated several instances where the homogeneous aquifer solutions give inconsistent estimates of aquifer diffusivity from measurements of tidal lag and attenuation. This paper presents new algebraic solutions for tidal propagation in spatially heterogeneous one-dimensional aquifers. By building on existing solutions for homogeneous aquifers, comprehensive solutions are presented for composite aquifers comprising of arbitrary (finite) numbers of contiguous homogeneous sub-aquifers and subject to sinusoidal linear boundary conditions. Both Cartesian and radial coordinate systems are considered. Properties of the solutions, including rapid phase shifting and attenuation effects, are discussed and their practical relevance noted. Consequent modal dispersive effects on tidal waveforms are also examined via tidal constituent analysis. It is demonstrated that, for multi-constituent tidal forcings, measured peak heights of head oscillations can seem to increase, and phase lags seem to decrease, with distance from the forcing boundary unless constituents are separated and considered in isolation.     

Steady flow to a partially penetrating blind‐wall well in a confined aquifer

Wells in aquifers of loose collapsible sediment are cased so that they have a blind wall and gain water only from the bottom. The hydraulic gradient established at the bottom of these wells during pumping brings the aquifer materials in a quicksand state, which may cause abrasion of pipes and pumps and even the destruction of well structure. To examine the quicksand occurrence, an analytical solution for the steady flow to a partially penetrating blind‐wall well in a confined aquifer is developed. The validity of the proposed solution is evaluated numerically. The sensitivity of maximum vertical gradient along the well bottom in response to aquifer and well parameters is examined. The solution is presented in the form of dimensionless‐type curves and equations that can be easily used to design the safe pumping rate and optimum well geometry to protect the well against sand production. The solution incorporates the anisotropy of aquifer materials and can also be used to determine the hydraulic conductivity of the aquifer. Copyright © 2012 John Wiley & Sons, Ltd.     

Underdamped slug tests with unsaturated‐saturated flows by considering effects of wellbore skins

An analytical solution is presented for the slug tests conducted in a partially penetrating well in an unconfined aquifer affected from above by an unsaturated zone. The solution considers the effects of wellbore skin and oscillatory responses on underdamped slug tests. The flow in the saturated zone is described by a two‐dimensional, axially symmetric governing equation, and the flow in the unsaturated zone above the water table by a linearized one‐dimensional Richards' equation. The unsaturated medium properties are represented by the exponential constitutive relationships. A Laplace domain solution is derived using the Laplace and finite Fourier transform and the solution in the real‐time domain is evaluated using the numerical inverse Laplace transform method. The solution derived in this study is more general and reduces to the most commonly used solutions for slug tests in their specified conditions. It is found that the unsaturated flow has a significant impact on the slug test conducted in an unconfined aquifer. The impact of unsaturated flow on such a slug test is enhanced with a larger anisotropy ratio, a shorter well screen length, a shorter distance between the well screen and the water table, or a larger well screen radius. The impact of unsaturated flow on slug tests decreases as the degree of penetration (the length of well screen) increases. For a fixed well screen length, the impact of unsaturated flow on slug tests decreases as the distance between the centre of screen and the water table increases. A large dimensionless well screen radius (>0.01) leads to significant effects of unsaturated flow on slug tests. The unsaturated flow reduces the oscillatory responses to underdamped slug tests. The unsaturated zone has significant impact on slug test under high‐permeability wellbore skin.     

Estimation of seawater retreat timescales in homogeneous and confined coastal aquifers based on dimensional analysis

Reliable estimation of the timescales of seawater retreat (SWR) in coastal aquifers has significant implications for sustainable groundwater management in coastal areas. Due to the complexity of coastal dynamics, analytical estimates of SWR timescales are limited in number, and numerical models are mainly utilized. Although numerical models allow for accurate analysis of the coastal systems, they concern particular aquifer cases, thus their results are not generally applicable. Here, we perform a dimensional analysis for the depth-integrated freshwater/seawater continuity equations and identify the dimensionless parameters that affect SWR in confined, homogeneous and flux-controlled aquifers. Based on numerical simulations, we gain insight into how these parameters affect SWR, and produce type curves which can be used as a simple tool for estimating SWR timescales in idealized coastal systems, independent of the hydraulic and geometric characteristics of the aquifer. The reliability of our estimates in real-world applications is also discussed.     

Ground water whirls

Numerical experiments with steady-state ground water flow models show that spiraling flow lines occur in layered aquifers that have different anisotropic horizontal hydraulic conductivities in adjacent layers. Bundles of such flow lines turning in the same direction can be referred to as ground water whirls. An anisotropic layered block in a field of uniform horizontal flow results in one or more whirls with their axes in the uniform flow direction. The number of whirls depends on the number of interfaces between layers with different anisotropic properties. For flow to a well in an aquifer consisting of two anisotropic layers, with perpendicular major principal directions, whirls are found to occur in quadrants that are bounded by the principal directions of the hydraulic conductivity. The combined effect of flow to a well and a layered anisotropy implies that a single well in a system with a single anisotropic layer within an otherwise isotropic aquifer causes eight whirls. All adjacent whirls rotate in opposite directions.     

A double-porosity model for a fractured aquifer with non-Darcian flow in fractures

Abstract

Non-Darcian flow in a finite fractured confined aquifer is studied. A stream bounds the aquifer at one side and an impervious stratum at the other. The aquifer consists of fractures capable of transmitting water rapidly, and porous blocks which mainly store water. Unsteady flow in the aquifer due to a sudden rise in the stream level is analysed by the double-porosity conceptual model. Governing equations for the flow in fractures and blocks are developed using the continuity equation. The fluid velocity in fractures is often too high for the linear Darcian flow so that the governing equation for fracture flow is modified by Forcheimer's equation, which incorporates a nonlinear term. Governing equations are coupled by an interaction term that controls the quasi-steady-state fracture—block interflow. Governing equations are solved numerically by the Crank-Nicolson implicit scheme. The numerical results are compared to the analytical results for the same problem which assumes Darcian flow in both fractures and blocks. Numerical and analytical solutions give the same results when the Reynolds number is less than 0.1. The effect of nonlinearity on the flow appears when the Reynolds number is greater than 0.1. The higher the rate of flow from the stream to the aquifer, the higher the degree of nonlinearity. The effect of aquifer parameters on the flow is also investigated. The proposed model and its numerical solution provide a useful application of nonlinear flow models to fractured aquifers. It is possible to extend the model to different types of aquifer, as well as boundary conditions at the stream side. Time-dependent flow rates in the analysis of recession hydrographs could also be evaluated by this model.     

Numerical Modeling of Slug Tests with MODFLOW Using Equivalent Well Blocks

Slug tests are a widely used technique to estimate aquifer hydraulic parameters and the test data are generally interpreted with analytical solutions under various assumptions. However, these solutions are not convenient when slug tests are required to be analyzed in a three‐dimensional model for complex aquifer‐aquitard systems. In this study, equivalent well blocks (EWB) are proposed in numerical modeling of slug test data with MODFLOW. Multi‐well slug tests in partially penetrating wells with skin zones can be simulated. Accuracy of the numerical method is demonstrated by benchmarking with analytical solutions. The EWB method is applied in a case study on slug tests in aquitards in the Pearl River Delta, China.     

Estimating hydraulic properties using a moving-model approach and multiple aquifer tests

A new method was developed for characterizing geohydrologic columns that extended >600 m deep at sites with as many as six discrete aquifers. This method was applied at 12 sites within the Southwest Florida Water Management District. Sites typically were equipped with multiple production wells, one for each aquifer and one or more observation wells per aquifer. The average hydraulic properties of the aquifers and confining units within radii of 30 to >300 m were characterized at each site. Aquifers were pumped individually and water levels were monitored in stressed and adjacent aquifers during each pumping event. Drawdowns at a site were interpreted using a radial numerical model that extended from land surface to the base of the geohydrologic column and simulated all pumping events. Conceptually, the radial model moves between stress periods and recenters on the production well during each test. Hydraulic conductivity was assumed homogeneous and isotropic within each aquifer and confining unit. Hydraulic property estimates for all of the aquifers and confining units were consistent and reasonable because results from multiple aquifers and pumping events were analyzed simultaneously.     

Stream tube integration method for analysing subsurface fluid flow

A stream tube integration method is introduced to solve transient subsurface fluid flow problems. The method combines a geometry-embedded form of Darcy's Law and the notion of location of average. Two types of problems, transient radial flow to a well of finite radius in an areally infinite aquifer and in a double porosity system, are solved by the stream tube integration method and the integral finite difference method. Results of the solutions show that the stream tube integration method, with fixed coarse mesh, are more accurate and better behaved than the integral finite difference method, with fine mesh. The fixed mesh stream tube integration method is readily extended to the moving mesh method. With much coarse mesh, the moving mesh technique can obtain the same accurate results as the fixed mesh stream tube integration method. It is suggested that the stream tube integration method is a viable way to state, solve, interpret and verify numerical solutions. The method provides efficient computation and improved accuracy for analysing subsurface fluid flow. © 1998 John Wiley & Sons, Ltd.     

A novel analytical solution for a slug test conducted in a well with a finite-thickness skin

An aquifer containing a skin zone is considered as a two-zone system. A mathematical model describing the head distribution is presented for a slug test performed in a two-zone confined aquifer system. A closed-form solution for the model is derived by Laplace transforms and Bromwich integral. This new solution is used to investigate the effects of skin type, skin thickness, and the contrast of skin transmissivity to formation transmissivity on the distributions of dimensionless hydraulic head. The results indicate that the effect of skin type is marked if the slug-test data is obtained from a radial two-zone aquifer system. The dimensionless well water level increases with the dimensionless positive skin thickness and decreases as the dimensionless negative skin thickness increases. In addition, the distribution of dimensionless well water level due to the slug test depends on the hydraulic properties of both the wellbore skin and formation zones.     

Identifying Aquifer Type in Fractured Rock Aquifers using Harmonic Analysis

Determining aquifer type, unconfined, semi‐confined, or confined, by drilling or performing pumping tests has inherent problems (i.e., cost and complex field issues) while sometimes yielding inconclusive results. An improved method to cost‐effectively determine aquifer type would be beneficial for hydraulic mapping of complex aquifer systems like fractured rock aquifers. Earth tides are known to influence water levels in wells penetrating confined aquifers or unconfined thick, low‐porosity aquifers. Water‐level fluctuations in wells tapping confined and unconfined aquifers are also influenced by changes in barometric pressure. Harmonic analyses of water‐level fluctuations of a thick (～1000 m) carbonate aquifer located in south‐central Oklahoma (Arbuckle‐Simpson aquifer) were utilized in nine wells to identify aquifer type by evaluating the influence of earth tides and barometric‐pressure variations using signal identification. On the basis of the results, portions of the aquifer responded hydraulically as each type of aquifer even though there was no significant variation in lithostratigraphy. The aquifer type was depth dependent with confined conditions becoming more prevalent with depth. The results demonstrate that harmonic analysis is an accurate and low‐cost method to determine aquifer type.