Synthesis and Characterization of Poly(2‐hydroxyethylmethacrylate‐hydroxyapatite) a Novel Composite for the Removal of Lead(II) from Aqueous Solutions

In the present study, a novel adsorbent, poly (2‐hydroxyethylmethacrylate‐hydroxyapatite) [P(HEMA‐Hap)], was prepared and characterized. The synthesis was achieved by means of free‐radical polymerization and a number of structural characterization methods, including FT‐IR, XRD, TGA, SEM, BET‐porosity, and swelling tests. Pb²⁺ adsorption was performed using a series of pH, time, and temperature ranges. The reusability of the composite was also tested. The results obtained indicated that the novel adsorbent is able to bind Pb²⁺ ions with strong chemical affinity. The adsorption results were fitted to the classic Langmuir, Freundlich, and Dubinin–Radushkevich (D–R) sorption models. Thermodynamic parameters obtained demonstrated that the sorption process was spontaneous (ΔG < 0), endothermic (ΔH > 0), as expected. The process was also consistent with the pseudo‐second‐order model, and chemical adsorption was determined to be the rate‐controlling step. It was also shown that the composite could be used for five consecutive adsorption processes.     

Use of Pistachio Shells as an Adsorbent for the Removal of Zinc(II) Ion

In this study, the removal of zinc(II) ion from an aqueous solution by pistachio shells (PS) is investigated. The dynamic behavior of the adsorption is examined on the effects of pH, adsorbent dosage, and contact time. The adsorption rates are determined quantitatively and simulated by the Lagergren first order, pseudo‐second order, Elovich, and intra‐particle diffusion kinetic models. The adsorption kinetic models are also tested for validity. The thermodynamic parameters, which are also deduced from adsorption experiments, are very useful in elucidating the nature of adsorption. The experimental results reveal that the optimum pH value and the contact time for the adsorption of Zn²⁺ onto PS are found as 6 and 10 min, respectively. According to these parameters, adsorption process follows the pseudo‐second order kinetic model with high correlation coefficients (R² = 0.999). The obtained results demonstrate that PS is a reasonably effective adsorbent for the removal of Zn²⁺ from aqueous leachate of hazardous waste.     

A Study: Removal of Cu(II), Cd(II), and Pb(II) Ions from Real Industrial Water and Contaminated Water Using Activated Sludge Biomass

This study aims to remove of Cu²⁺, Cd²⁺, and Pb²⁺ ions from solution and to investigate the adsorption isotherms, adsorption kinetics, and ion‐exchange affinities of these metals using waste activated sludge (AS) biomass. The adsorptions of the metals on biomass were optimal at an acidic pH value of 6.0 based on its monolayer capacities. Maximum monolayer capacities of AS biomass (q_max) were calculated as 0.478, 0.358, and 0.280 mmol g^?1 for Cu²⁺, Cd²⁺, and Pb²⁺, respectively, and the adsorption equilibrium time was found as 60 min for each metal. The adsorbed amount of metal rose with increasing of initial metal ion concentration. The equilibrium adsorption capacity of AS for initial 0.25 mmol L^?1 metal concentration was determined as 0.200, 0.167, and 0.155 mmol g^?1 for Cu²⁺, Cd²⁺, and Pb²⁺ ions, respectively. These relevant values were determined as 0.420, 0.305, and 0.282 mmol g^?1 for Cu²⁺, Cd²⁺, and Pb²⁺ ions, respectively, when initial metal concentration was 0.50 mmol L^?1. In the multi‐metal sorption system, the adsorption capacity of AS biomass was observed in the order of Cu²⁺ > Cd²⁺ > Pb²⁺. In the presence of 100 mmol L^?1 H⁺ ion, the order of ion‐exchange affinity with H⁺ was found as Cu²⁺ > Cd²⁺ > Pb²⁺. The adsorption kinetics were also found to be well described by the pseudo‐second‐order and intraparticle diffusion models. Two different rate constants were obtained as k_i1 and k_i2 and k_i1 (first stage) was found to be higher than k_i2 (second stage).     

Study of the Contributions of Non‐Specific and Specific Interactions during Fluoxetine Adsorption onto Activated Carbons

The adsorption of fluoxetine onto activated carbons (ACs) prepared from almond tree pruning by steam and CO₂ activation under different temperature conditions (650–950°C), was studied. In both series increasing the temperature caused an increase in the BET apparent surface area, yielding ACs with S_BET up to 870 and 710 m² g^?1 after steam and CO₂ activation, respectively. Also, a slight widening of the porosity was found in both cases. In order to modify the functionality of the ACs, two of them were impregnated with triethylenediamine (TEDA) prior to the adsorption process, which caused a decrease in the AC apparent surface mainly due to micropore blockage. The fluoxetine adsorption isotherms at 25°C showed maximum adsorption capacities between 110 and 224 mg g^?1. The adsorption isotherms were analyzed using Langmuir and Freundlich models. Although the impregnation reduced the pore volume, it did not cause a decrease in the fluoxetine maximum adsorption capacity, but a modification in the adsorption mechanism was observed.     

Adsorption studies of aqueous Pb(II) onto a sugarcane bagasse/multi-walled carbon nanotube composite

Adsorption of Pb²⁺ from aqueous solution onto a sugarcane bagasse/multi-walled carbon nanotube (MWCNT) composite was investigated by using a series of batch adsorption experiments and compared with the metal uptake ability of sugarcane bagasse. The efficiency of the adsorption processes was studied experimentally at various pH values, contact times, adsorbent masses, temperatures and initial Pb²⁺ concentrations. A pH of 4.5 was found to be the optimum pH to obtain a maximum adsorption percentage in 120 min of equilibration time. The composite showed a much enhanced adsorption capacity for Pb²⁺ of 56.6 mg g⁻¹ compared with 23.8 mg g⁻¹ for bagasse at 28 °C. The Langmuir adsorption isotherm provided the best fit to the equilibrium adsorption data. The pseudo first-order, pseudo second-order, intraparticle diffusion and Elovich kinetics models were used to analyse the rate of lead adsorption and the results show that the Elovich model is more suitable. The thermodynamic parameters of adsorption, namely ΔG°, ΔH° and ΔS°, were determined over the temperature range of 20–45 °C. The adsorption of Pb²⁺ onto both bagasse and the sugarcane bagasse/MWCNT composite was found to be spontaneous but for the former adsorbent it was enthalpy-driven whereas for the latter it was entropy-driven. Desorption of the lead-loaded adsorbents was fairly efficient with 0.1 mol dm⁻³ HCl. Overall this composite has the potential to be a good adsorbent for the removal of Pb²⁺ from wastewaters.     

Acute Toxicity of Mercury,Copper and Zinc to a Freshwater Pulmonate Snail,Lymnaea luteola (LAMARCK)

The short-term toxicity of mercury, copper and zinc was studied using a freshwater pulmonate snail, Lymnaea luteola (LAMARCK ). The median period of survival increases with decreasing the toxicant concentration. The 96 h LC₅₀ values and their confidence limits were 0.135 (0.112 … 0.186) ppm of Hg²⁺; 0.172 (0.118 … 0.355) ppm of Cu²⁺; and 6.13 (5.73 to 7.19) ppm of Zn²⁺. The relative potency ratio indicates that the Hg²⁺ ions were most toxic, followed by Cu²⁺ and Zn²⁺ ions.     

Adsorption of cobalt by using inorganic components of sediment samples from water bodies

The adsorption of cobalt ions was evaluated using sediment samples from water bodies to investigate the adsorption properties of sediment and the behavior of these natural materials in the presence of nuclear and industrial waste.The two sediments(S1 and S2)were treated to eliminate humic and fulvic acids and then they were characterized by several techniques.The minerals found in both the sediments(X-ray diffraction)were quartz and albite;plus,goethite and muscovite in S1,and kaolinite and montmorillonite in S2.Point of zero charge(PZC)of S1 and S2 was 6.00 and 5.22,respectively.The specific area of S1(63.3 m²/g)is higher than S2(1.5 m²/g).Adsorption kinetics data for S1 and S2 were best fitted to the pseudo second-order model.The removal efficiency of S1 for cobalt was 96%with an adsorption capacity(qe)of 0.93 mg/g,and for S2 was 45%with a qeof 0.40 mg/g.The experimental data of the adsorption isotherms were adjusted to Langmuir and Freundlich models for S1 and S2,respectively.The thermodynamic parameters(enthalpy,entropy,and Gibb’s free energy)indicated that the adsorption processes were endothermic,spontaneous,and chemisorption mechanism.The results show that the adsorption capacities of the sediments depend on their composition.These water sediments have important adsorption properties for cobalt,and they can be used in the treatment of nuclear and industrial aqueous wastes.     

Characterization and Application of Dried Plants to Remove Heavy Metals,Nitrate, and Phosphate Ions from Industrial Wastewaters

Low cost adsorbents were prepared from dried plants for the removal of heavy metals, nitrate, and phosphate ions from industrial wastewaters. The efficiency of these adsorbents was investigated using batch adsorption technique at room temperature. The dried plant particles were characterized by N₂ at 77 K adsorption, scanning electron microscopy, energy dispersive X‐ray spectroscopy, Fourier transform infrared spectroscopy, and phytochemical screening. The adsorption experiments showed that the microparticles of the dried plants presented a good adsorption of heavy metals, phosphate, and nitrate ions from real wastewaters. This adsorption increased with increasing contact time. The equilibrium time was found to be 30 min for heavy metals and nitrate ions and 240 min for phosphate ions. After the adsorption process, the Pb(II) concentrations, as well as those of Cd(II), Cu(II), and Zn(II) were below the European drinking water norms concentrations. The percentage removal of heavy metals, nitrates, and phosphates from industrial wastewaters by dried plants was ～94% for Cd²⁺, ～92% for Cu²⁺, ～99% for Pb²⁺, ～97% for Zn²⁺, ～100% for ${\rm NO}_{{\rm 3}}^{{-} } $ and ～77% for ${\rm PO}_{{\rm 4}}^{3{-} } $ ions. It is proved that dried plants can be one alternative source for low cost absorbents to remove heavy metals, nitrate, and phosphate ions from municipal and industrial wastewaters.     

Effect of Zinc,Copper and Mercury on Channa marulius (HAMILTON)

Static bioassay acute toxicity tests of Zinc, Copper and Mercury were conducted to determine the median lethal concentrations (LC₅₀s) of a freshwater teleost Channa marulius (HAM .) The 96 h LC₅₀ and 95% confidence limits for Zn²⁺ were 25.61 (24.13 … 27.12) mg/l; 0.90 (0.80 … 1.038) mg/l; for Cu²⁺ and 0.314 (0.257 … 0.371) mg/l for Hg²⁺. However, these values decreased at 240 h of exposure and were: 21.09 (18.29 … 24.60) mg Zn²⁺/l; 0.66 (0.568 … 0.841) mg Cu²⁺/l; and 0.131 (0.103 … 0.158) mg Hg²⁺/l. The relative potency ratio of Zn/Hg, Zn/Cu and Cu/Hg suggests that fish were most sensitive to Hg, followed by Cu and Zn ions. The acute toxicities of mixtures of Zn²⁺?Cu²⁺; Zn²⁺?Hg²⁺, Cu²⁺?Hg²⁺ and Zn²⁺?Cu²⁺?Hg²⁺ up to 48 h of exposure were also investigated. The additive index and ranges for Zn²⁺?Cu²⁺ were ?0.241 (-0.577 … 0.054); 0.056 (-0.269 … 0.475) for Zn-Hg; 0.285 (-0.043 … 0.718) for Cu-Hg; and -0.542 (-1.215 … 0.005) for Zn-Cu-Hg. All the mixtures tested showed a greater than additive toxicity because index ranges overlapped zero.     

Assessment of groundwater quality and its suitability for drinking and agricultural uses in arid environment

Groundwater quality in Ma’an area was evaluated for its suitability for drinking and agricultural uses by determining the main physical and chemical properties during a 1 year survey study (August 2009 to August 2010). Several samples were collected from ten different wells and analysed for temperature, pH, conductivity, total dissolved solids, total hardness, major cations (Ca²⁺, Mg²⁺, Na⁺ and K⁺), major anions (HCO₃ ^?, Cl^?, NO₃ ^?, SO₄ ^2?, F^? and Br^?) and trace metals (Fe²⁺, Al³⁺, Mn²⁺, Cu²⁺, Zn²⁺, Pb²⁺ and Cd²⁺). The general chemistry of water samples was typically of alkaline earth waters with prevailing bicarbonate chloride. The results showed great variations among the analyzed samples with respect to their physical and chemical parameters. However, most values were below the maximum permissible levels recommended by Jordanian and WHO drinking water standards. The quality assessment shows that in general, the GW in the study area is not entirely fit for direct drinking with respect to EC, and Pb²⁺. According to the residual sodium carbonate and sodium adsorption ratio, the water in the studied wells can be used for irrigational purposes.     

Removal of Cadmium from Aqueous Solution Using Castor Seed Hull: A Kinetic and Equilibrium Study

The effects of various parameters such as initial concentration, adsorbent loading, pH, and contact time on kinetics and equilibrium of adsorption of Cd²⁺ metal ion from its aqueous solution by castor seed hull (CSH) and also by activated carbon have been investigated by batch adsorption experiments. The amount of adsorption increases with initial metal ion concentration, contact time, solution pH, and the loading of adsorbent for both the systems. Kinetic experiments indicate that adsorption of cadmium metal ion on both CSH and on activated carbon consists of three steps – a rapid adsorption of cadmium metal ion, a transition phase, and an almost flat plateau region. This has also been confirmed by the intraparticle diffusion model. The lumped kinetic results show that the cadmium adsorption process follows a pseudo‐second order rate law. The kinetic parameters including the rate constant are determined at different initial metal ion concentrations, pH, amount, and type of adsorbent, respectively. The Langmuir and Freundlich adsorption isotherm models are used to describe the experimental data. The Langmuir model yields a better correlation coefficient than the other model. A comparison of the monolayer adsorption capacity (q_m) of CSH, activated carbon, and several other reported adsorbents has been provided. The value of separation factor (R_L) calculated from the Langmuir equation also gives an indication of favorable adsorption of the metal ion. From comparative studies, it has been found that CSH is a potentially attractive adsorbent than commercial activated carbon for cadmium metal ion (Cd²⁺) removal.     

Hg,Cd对莼菜冬芽茎、叶叶绿素含量及活性氧清除系统的影响

利用人工配制的生活污水先进行单胞藻（斜生栅落Ｓｃｅｎｅｄｅｓｍｕｓ ｏｂｌｉｑｕｕｓ Ｔｕｒｐ）的培养,再接种田螺（Ｃｉｐａｎｇｏｐａｌｕｄｉｎａ ｓｐ．）和短钝蚤（Ｄａｐｈｎｉａ ｏｂｔｕｓａ Ｋｕｒｚ）对栅藻密度的经时变化,短钝蚤种群增长及水体中氮,磷,碳在培养过程中的变化作了与分析。     

Analysis of Diffusion and Adsorption of Volatile Organic Compounds in Zeolites by a Single Pellet Moment Technique

The diffusion and adsorption of two common volatile organic compounds, i. e., methanol and benzene, in different zeolite pellets were studied experimentally by using the single pellet moment technique. The experiments were conducted in a one‐sided single pellet adsorption cell at different temperatures in the range between 303 and 343 K. The results showed that both volatile organic tracers were adsorbed reversibly onto all zeolite samples. The overall adsorption equilibrium constants of both volatile organic compounds decreased with increasing temperature. The adsorption of the tracers onto the zeolite samples were found to increase in the order of NaY > clinoptilolite > 4A. In the range between 303 and 343 K, the adsorption constants of benzene range from 10.51 to 5.52 for zeolite 4A, from 11.90 to 6.37 for clinoptilolite and from 20.32 to 9.82 for NaY. The adsorption constants of methanol range from 19.05 to 8.26 for zeolite 4A, from 38.40 to 9.12 for clinoptilolite and from 74.21 to 14.70 for NaY at temperatures between 303 and 333 K. The effective diffusivities for benzene varied from 2.20·10^–6 to 13.01·10^–6 m²/s, whereas for methanol, they varied from 9.80·10^–6 to 15.60·10^–6 m²/s at the temperatures studied.     

Removal of Cu2+ and Pb2+ Ions Using CMC Based Thermoresponsive Nanocomposite Hydrogel

In this study, carboxymethylcellulose (CMC) based thermoresponsive nanocomposite hydrogel was synthesized for the removal of Cu²⁺ and Pb²⁺ ions from aqueous solutions. To prepare nanocomposite hydrogel, graft copolymerization of N‐isopropyl acrylamide (NIPAm) and acrylic acid (AA) onto CMC was carried out in Na‐montmorillonite (MMT)/water suspension media and ammonium persulfate (APS) used as initiator. The chemical structures of hydrogels were characterized by Fourier transform infrared (FT‐IR) and X‐ray diffraction spectroscopy (XRD). Lower critical solution temperature (LCST), pH responsivity, swelling, and deswelling properties of the hydrogels were also examined. In addition competitive and non‐competitive removal of Cu²⁺ and Pb²⁺ studies were carried out. According to heavy metal sorption studies results, removal capacities of nanocomposite hydrogel for both metal ions were found to be higher than those of pure hydrogel. The analyzed adsorption data showed that the adsorption process of Cu²⁺ and Pb²⁺ could be explained by pseudo‐second order kinetic model. Moreover, according to competitive sorption studies, it is found to be that both hydrogels are more selective to Cu²⁺ ion rather than Pb²⁺.     

Studies on the Removal of Iron from Drinking Water by Electrocoagulation – A Clean Process

The present study describes an electrocoagulation process for the removal of iron from drinking water using magnesium as the anode and galvanized iron as the cathode. Experiments were carried out as a function of pH, temperature and current density. The adsorption capacity was evaluated using both the Langmuir and the Freundlich isotherm models. The results show that the maximum removal efficiency of 98.4% was achieved at a current density of 0.06 A dm^–2, at a pH of 6.0. The adsorption of iron was better explained by fitting the Langmuir adsorption isotherm, which suggests a monolayer coverage of adsorbed molecules. The adsorption process followed a second‐order kinetics model. Temperature studies showed that adsorption was endothermic and spontaneous in nature.     

Base Treated Cogon Grass (Imperata cylindrica) as an Adsorbent for the Removal of Ni(II): Kinetic,Isothermal and Fixed‐bed Column Studies

The adsorption of Ni(II) from aqueous solutions using base treated cogon grass or Imperata cylindrica (NHIC) was performed under batch and column modes. Batch experiments were conducted to determine the factors affecting adsorption such as pH, adsorbent dosage, initial nickel concentration, contact time and temperature. The fixed‐bed column experiment was performed to determine the practical applicability of NHIC and to obtain the breakthrough curve. Adsorption was fast as equilibrium was achieved within 60 min, and was best described by the pseudo second order model. According to the Langmuir model, a maximum adsorption capacity of 6.96 mg/g was observed at pH 5 and at a temperature of 313 K. Thermodynamic parameters such as ΔG⁰, ΔH⁰ and ΔS⁰ were calculated, and indicated that adsorption was a spontaneous and endothermic process. The mechanistic pathway of Ni(II) uptake was examined by Fourier transform infrared (FTIR) spectroscopy, scanning electron microscopy (SEM) and energy dispersive X‐ray (EDX) spectroscopy. The Thomas and Yoon‐Nelson models were used to analyze the fixed‐bed column data.     

Adsorption of Cadmium Ions from Aqueous Solution Using Granular Activated Carbon and Activated Clay

The present study was aimed at removing cadmium ions from aqueous solution through batch studies using adsorbents, such as, granular activated carbon (GAC) and activated clay (A‐clay). GAC was of commercial grade where as the A‐clay was prepared by acid treatment of clay with 1 mol/L of H₂SO₄. Bulk densities of A‐clay and GAC were 1132 and 599 kg/m³, respectively. The surface areas were 358 m²/g for GAC and 90 m²/g for A‐clay. The adsorption studies were carried out to optimize the process parameters, such as, pH, adsorbent dosage, and contact time. The results obtained were analyzed for kinetics and adsorption isotherm studies. The pH value was optimized at pH 6 giving maximum Cd removal of 84 and 75.2% with GAC and A‐clay, respectively. The adsorbent dosage was optimized and was found to be 5 g/L for GAC and 10 g/L for A‐clay. Batch adsorption studies were carried out with initial adsorbate (Cd) concentration of 100 mg/L and adsorbent dosage of 10 g/L at pH 6. The optimum contact time was found to be 5 h for both the adsorbents. Kinetic studies showed Cd removal a pseudo second order process. The isotherm studies revealed Langmuir isotherm to better fit the data than Freundlich isotherm.     

Acute toxicity of inorganic mercury to Capitella

The polychaete worm Capitella capitata is shown to be fairly resistant to high concentrations of inorganic mercury. Survival of adults compared with those of the polychaete Ophryotrocha labronica shows that C. capitata can withstand 1 ppm Hg²⁺ for several days whilst O. labronica succombs to 0.5 ppm Hg²⁺ in 2 h.     

The Adsorption Behavior of Functional Particles Modified by Polyvinylimidazole for Cu(II) Ion

In this paper, a novel composite material the silica grafted by poly(N‐vinyl imidazole) (PVI), i.e., PVI/SiO₂, was prepared using 3‐methacryloxypropyl trimethoxysilane (MPS) as intermedia through the “grafting from” method. The adsorption behavior of metal ions by PVI/SiO₂ was researched by both static and dynamic methods. Experimental results showed that PVI/SiO₂ possessed very strong adsorption ability for metal ions. For different metal ions, PVI/SiO₂ exhibited different adsorption abilities with the following order of adsorption capacity: Cu²⁺ > Cd²⁺ > Zn²⁺. The adsorption material PVI/SiO₂ was especially good at adsorbing Cu(II) ion and the saturated adsorption capacity could reach up to 49.2 mg/g. The empirical Freundlich isotherm was found to describe well the equilibrium adsorption data. Higher temperatures facilitated the adsorption process and thus increased the adsorption capacity. The pH and grafting amount of PVI had great influence on the adsorption amount. In addition, PVI/SiO₂ particles had excellent eluting and regenerating property using diluted hydrochloric acid solution as eluent. The adsorption ability trended to steady during 10 cycles.     

Preparation of Nano‐Lepidocrocite and an Investigation of Its Ability to Remove a Metal Complex Dye

Lepidocrocite (γ‐FeOOH) nanoparticles were synthesized from iron(II) sulfate solution and characterized using X‐ray diffraction (XRD), transmission electron microscopy (TEM), Fourier transform‐IR (FT‐IR), nitrogen adsorption, and point of zero charge pH (pH_PZC) analyses. TEM, XRD, and FT‐IR analyses proved the synthesis of nano‐lepidocrocite. Surface area and pH_PZC of the synthesized lepidocrocite were 68.1 m² g^?1 and 4.8, respectively. Utilization of the synthesized lepidocrocite in the adsorption of Lanacron brown S‐GL (LBS‐GL) from aqueous solutions was investigated, and the effect of lepidocrocite dosage, pH, temperature, and contact time on this process were optimized and modeled using response surface methodology approach. The lepidocrocite dosage of 0.015 g, pH 3.5, temperature of 38°C, and contact time of 100 min were determined as optimum adsorption conditions. Isotherm and kinetics of the adsorption process were analyzed at the optimum conditions. The equilibrium data were fitted well to the Langmuir isotherm model. The maximum monolayer adsorption capacity was 528.21 mg g^?1. The adsorption process was described by the pseudo‐second‐order kinetic model. Furthermore, the effect of pH on the desorption of LBS‐GL was investigated. High LBS‐GL desorption efficiency was achieved at a high pH value.