High-resolution parallel electron energy-loss spectroscopy of Mn L2,3-edges in inorganic manganese compounds

Parallel electron energy-loss spectroscopy (PEELS) in a scanning transmission electron microscope (STEM) was used to record the Mn L_2,3-edges from a range of natural and synthetic manganese containing materials, covering valences 0, II, III, IV and VII, with an energy resolution of ca. 0.5 eV. The Mn L_2,3 electron-loss near-edge structure (ELNES) of these edges provided a sensitive fingerprint of its valence. The Mn²⁺ L_2,3-edges show little sensitivity to the local site symmetry of the ligands surrounding the manganese. This is illustrated by comparing the Mn L_2,3-edges from 4-, 6- and 8-fold coordinated Mn²⁺. In contrast, the Mn L₃-edges from Mn³⁺ and Mn⁴⁺ containing minerals exhibited ELNES that are interpreted in terms of a crystal-field splitting of the 3d electrons, governed by the symmetry of the surrounding ligands. The Mn L₃-edges for octahedrally coordinated Mn²⁺, Mn³⁺ and Mn⁴⁺ showed variations in their ELNES that were sensitive to the crystal-field strength. The crystal-field strength (10Dq) was measured from these edges and compared very well with published optically determined values. The magnitude of 10Dq measured from the Mn L₃-edges and their O K-edge prepeaks of the manganese oxides were almost identical. This further confirms that the value of 10Dq measured at the Mn L₃-edge is correct. Selected spectra are compared with theoretical 2p atomic multiplet spectra and the differences and similarities are explained in terms of the covalency and site symmetry of the manganese. The Mn L₃-edges allow the valence of the manganese to be ascertained, even in multivalent state materials, and can also be used to determine 10Dq.     

Release,transport and attenuation of metals from an old tailings impoundment

The oxidation of sulfide minerals from mine wastes results in the release of oxidation products to groundwater and surface water. The abandoned high-sulfide Camp tailings impoundment at Sherridon, Manitoba, wherein the tailings have undergone oxidation for more than 70 a, was investigated by hydrogeological, geochemical, and mineralogical techniques. Mineralogical analysis indicates that the unoxidized tailings contain nearly equal proportions of pyrite and pyrrhotite, which make up to 60 wt% of the total tailings, and which are accompanied by minor amounts of chalcopyrite and sphalerite, and minute amounts of galena and arsenopyrite. Extensive oxidation in the upper 50 cm of the tailings has resulted in extremely high concentrations of dissolved SO₄ and metals and As in the tailings pore water (pH < 1, 129,000 mg L⁻¹ Fe, 280,000 mg L⁻¹ SO₄, 55,000 mg L⁻¹ Zn, 7200 mg L⁻¹ Al, 1600 mg L⁻¹ Cu, 260 mg L⁻¹ Mn, 110 mg L⁻¹ Co, 97 mg L⁻¹ Cd, 40 mg L⁻¹ As, 15 mg L⁻¹ Ni, 8 mg L⁻¹ Pb, and 3 mg L⁻¹ Cr). The acid released from sulfide oxidation has been extensive enough to deplete carbonate minerals to 6 m depth and to partly deplete Al-silicate minerals to a 1 m depth. Below 1 m, sulfide oxidation has resulted in the formation of a continuous hardpan layer that is >1 m thick. Geochemical modeling and mineralogical analysis indicate that the hardpan layer consists of secondary melanterite, rozenite, gypsum, jarosite, and goethite. The minerals indicated mainly control the dissolved concentrations of SO₄, Fe, Ca and K. The highest concentrations of dissolved metals are observed directly above and within the massive hardpan layer. Near the water table at a depth of 4 m, most metals and SO₄ sharply decline in concentration. Although dissolved concentrations of metals and SO₄ decrease below the water table, these concentrations remain elevated throughout the tailings, with up to 60,600 mg L⁻¹ Fe and 91,600 mg L⁻¹ SO₄ observed in the deeper groundwater. During precipitation events, surface seeps develop along the flanks of the impoundment and discharge pore water with a geochemical composition that is similar to the composition of water directly above the hardpan. These results suggest that shallow lateral flow of water from a transient perched water table is resulting in higher contaminant loadings than would be predicted if it were assumed that discharge is derived solely from the deeper primary water table. The abundance of residual sulfide minerals, the depletion of aluminosilicate minerals in the upper meter of the tailings and the presence of a significant mass of residual sulfide minerals in this zone after 70 a of oxidation suggest that sulfide oxidation will continue to release acid, metals, and SO₄ to the environment for decades to centuries.     

Enrichment of Rh,Ru, Ir and Os in Cr spinels from oxidized magmas: Evidence from the Ambae volcano,Vanuatu

Experimental studies, performed under oxidized conditions (fO₂ > QFM + 2, where QFM is quartz–fayalite–magnetite oxygen buffer), have shown that Rh, Ru, Ir and Os are strongly compatible with Cr spinel, whereas empirical studies of Cr spinels from ultramafic–mafic rocks suggest that the experimental results may overestimate the partition coefficients. We report laser-ablation inductively coupled plasma mass spectrometry (LA-ICP-MS) analyses of platinum-group elements (PGE), Au and Re abundances in Cr spinels from the Ambae volcano, Vanuatu (fO₂ = QFM + 2.5), the Jimberlana layered intrusion, western Australia, and the Bushveld complex, South Africa (fO₂ ～ QFM). The results show that Rh and IPGEs (Iridium-group PGE; Ru, Ir, Os) partition strongly into the Cr spinels that crystallized from the oxidized Ambae lavas whereas most of the Cr spinels from the more reduced Jimberlana layered intrusion and the Bushveld complex contain no detectable PGE, Au or Re, with exception of ～10 ppb of Ir in some Jimberlana Cr spinels. In the Ambae Cr spinels, Rh, Ru and, to lesser extent Os, are positively correlated with Fe³⁺, Ni and V. The homogeneous distribution of Rh and IPGEs in LA-ICP-MS time-resolved spectra indicates that these elements are in solid solution in Cr spinels. Pt–Fe alloys occur as inclusions within the Ambae Cr spinels, which indicate that the Ambae melt was saturated with Pt.Our results show that partitioning of Rh, Ru and Ir into Cr spinels increases with increasing oxygen fugacity, which suggests that the high concentrations of these elements in the Ambae Cr spinels are due to the high oxygen fugacity of the host magma. Therefore, Cr spinels may play an important role in controlling the concentrations of Rh and IPGEs during fractional crystallization of oxidized ultramafic–mafic magmas and during partial melting of oxidized arc mantle.     

The Diavik waste rock project: Initial geochemical response from a low sulfide waste rock pile

Three large-scale experimental waste rock piles (test piles) were constructed and instrumented at the Diavik Diamond Mine in the Northwest Territories, Canada, as part of an integrated field and laboratory study to measure and compare physical and geochemical characteristics of experimental, low sulfide waste rock piles at various scales. This paper describes the geochemical response during the first season from a test pile containing 0.053 wt.% S. Bulk drainage chemistry was measured at two sampling points for pH, Eh, alkalinity, dissolved cations and anions, and nutrients. The geochemical equilibrium model MINTEQA2 was used to interpret potential mineral solubility controls on water chemistry. The geochemical response characterizes the initial flushing response of blasting residues and oxidation products derived from sulfides in waste rock exposed to the atmosphere for less than 1 year. Sulfate concentrations reached 2000 mg L⁻¹ when ambient temperatures were >10 °C, and decreased as ambient temperatures declined to <0 °C. The pH decreased to <5, concomitant with an alkalinity minimum of <1 mg L⁻¹ (as total CaCO₃), suggesting all available alkalinity is consumed by acid-neutralizing reactions. Concentrations of Al and Fe were <0.36 and <0.11 mg L⁻¹, respectively. Trends of pH and alkalinity and the calculated saturation indices for Al and Fe (oxy)hydroxides suggest that dissolution of Al and Fe (oxy)hydroxide phases buffers the pH. The effluent water showed increased concentrations of dissolved Mn (<13 mg L⁻¹), Ni (<7.0 mg L⁻¹), Co (<1.5 mg L⁻¹), Zn (<0.5 mg L⁻¹), Cd (<0.008 mg L⁻¹) and Cu (<0.05 mg L⁻¹) as ambient temperatures increased. Manganese is released by aluminosilicate weathering, Ni and Co by pyrrhotite [Fe_1−xS] oxidation, Zn and Cd by sphalerite oxidation, and Cu by chalcopyrite [CuFeS₂] oxidation. No dissolved metals appear to have discrete secondary mineral controls. Changes in SO₄, pH and metal concentrations indicate sulfide oxidation is occurring and effluent concentrations are influenced by ambient temperatures and, possibly, increasing flow path lengths that transport reaction products from previously unflushed waste rock.     

Fluctuations in late Neoproterozoic atmospheric oxidation — Cr isotope chemostratigraphy and iron speciation of the late Ediacaran lower Arroyo del Soldado Group (Uruguay)

Oxygenation of the Earth's atmosphere occurred in two major steps, near the beginning and near the end of the Proterozoic Eon (2500 to 542 Ma ago), but the details of this history are unclear. Chromium isotopes in iron-rich chemical sediments offer a potential to highlight fine-scale fluctuations in the oxygenation of the oceans and atmosphere and to add a further dimension in the use of redox-sensitive tracers to solve the question regarding fluctuations of atmospheric oxygen levels and their consequences for Earth's climate. We observe strong positive fractionations in Cr isotopes (δ⁵³Cr up to + 5.0‰) in iron-rich cherts and banded iron formation horizons within the Arroyo del Soldado Group (Ediacaran; Uruguay) that can be explained by rapid, effective oxidation of Fe(II)-rich surface waters. These fluctuations are correlated with variations in ratios of highly reactive iron (Fe_HR) to total iron (Fe_tot) which indicate a predominance of anoxic water columns (Fe_HR/Fe_tot > 0.38) during the onset of oxidation pulses. We favor the scenario by which isotopically heavy Cr(VI) entered the basin after pulses of oxidative weathering on land and in which Fe(II) accumulated in the water column. Neodymium isotopes reveal that these oxygenation pulses were followed by increased influxes to the basin of continental crust-derived detrital components of Paleoproterozoic (Nd T_DM model ages = 2.1–2.2 Ga) provenance typical of the Rio de la Plata Craton. The association of positive δ⁵³Cr–ferruginous (Fe_HR/Fe_tot > 0.38) stratigraphic intervals with low-diversity acritarch assemblages dominated by Bavlinella faveolata strongly support models postulating a stratified, eutrophic Neoproterozoic ocean. Thus, even within a few million years of the Precambrian–Cambrian boundary, paleoceanographic conditions resembled more those of Paleoproterozoic oceans than Phanerozoic and present oceans. This highlights the sheer magnitude of ecological changes at the Precambrian–Cambrian transition, changes which ultimately led to the demise of the Precambrian world and the birth of the metazoan-dominated Phanerozoic.     

Dielectric loss in ore-forming chromium spinel at temperatures from 20 to 800 °C

Physical, physicochemical, and mineralogical-petrographic methods have been applied to samples of ophiolite-hosted chromite ore from different deposits and occurrences in the Urals. Temperature dependences of dielectric loss obtained for nine chromite ore samples consisting of 95–98% Cr spinel show prominent peaks indicating a relaxation origin of the loss. The analyzed samples have the loss peaks at different temperatures depending mainly on H = (FeO/Fe₂O₃)^? : (FeO/Fe₂O₃)^??, where (FeO/Fe₂O₃)^? and (FeO/Fe₂O₃)^?? are, respectively, the ferrous/ferric oxide ratios in the samples before and after heating to 800 °C, and H is thus the heating-induced relative change in the FeO/Fe₂O₃ ratio. These peak temperatures vary from 550 °C (sample 1, high-Cr chromium spinel with more than 52% Cr₂O₃) to 750 °C (sample 2, aluminous and magnesian spinel with less than 30% Cr₂O₃), and H ranges correspondingly from 1.61 to 5.49. The temperature of the loss peaks is related with H as H = 34.30 ? 11.52N + 1.20N², with an error of σ = 0.19 (N = T · 10^?2, T is temperature in °C).     

An Apatite II permeable reactive barrier to remediate groundwater containing Zn,Pb and Cd

Phosphate-induced metal stabilization involving the reactive medium Apatite II™ [Ca_10−xNa_x(PO₄)_6−x(CO₃)_x(OH)₂], where x < 1, was used in a subsurface permeable reactive barrier (PRB) to treat acid mine drainage in a shallow alluvial groundwater containing elevated concentrations of Zn, Pb, Cd, Cu, SO₄ and NO₃. The groundwater is treated in situ before it enters the East Fork of Ninemile Creek, a tributary to the Coeur d’Alene River, Idaho. Microbially mediated SO₄ reduction and the subsequent precipitation of sphalerite [ZnS] is the primary mechanism occurring for immobilization of Zn and Cd. Precipitation of pyromorphite [Pb₁₀(PO₄)₆(OH,Cl)₂] is the most likely mechanism for immobilization of Pb. Precipitation is occurring directly on the original Apatite II. The emplaced PRB has been operating successfully since January of 2001, and has reduced the concentrations of Cd and Pb to below detection (2 μg L⁻¹), has reduced Zn to near background in this region (about 100 μg L⁻¹), and has reduced SO₄ by between 100 and 200 mg L⁻¹ and NO₃ to below detection (50 μg L⁻¹). The PRB, filled with 90 tonnes of Apatite II, has removed about 4550 kg of Zn, 91 kg of Pb and 45 kg of Cd, but 90% of the immobilization is occurring in the first 20% of the barrier, wherein the reactive media now contain up to 25 wt% Zn. Field observations indicate that about 30% of the Apatite II material is spent (consumed).     

An Apatite II permeable reactive barrier to remediate groundwater containing Zn,Pb and Cd

Phosphate-induced metal stabilization involving the reactive medium Apatite II™ [Ca_10−xNa_x(PO₄)_6−x(CO₃)_x(OH)₂], where x < 1, was used in a subsurface permeable reactive barrier (PRB) to treat acid mine drainage in a shallow alluvial groundwater containing elevated concentrations of Zn, Pb, Cd, Cu, SO₄ and NO₃. The groundwater is treated in situ before it enters the East Fork of Ninemile Creek, a tributary to the Coeur d’Alene River, Idaho. Microbially mediated SO₄ reduction and the subsequent precipitation of sphalerite [ZnS] is the primary mechanism occurring for immobilization of Zn and Cd. Precipitation of pyromorphite [Pb₁₀(PO₄)₆(OH,Cl)₂] is the most likely mechanism for immobilization of Pb. Precipitation is occurring directly on the original Apatite II. The emplaced PRB has been operating successfully since January of 2001, and has reduced the concentrations of Cd and Pb to below detection (2 μg L⁻¹), has reduced Zn to near background in this region (about 100 μg L⁻¹), and has reduced SO₄ by between 100 and 200 mg L⁻¹ and NO₃ to below detection (50 μg L⁻¹). The PRB, filled with 90 tonnes of Apatite II, has removed about 4550 kg of Zn, 91 kg of Pb and 45 kg of Cd, but 90% of the immobilization is occurring in the first 20% of the barrier, wherein the reactive media now contain up to 25 wt% Zn. Field observations indicate that about 30% of the Apatite II material is spent (consumed).     

Effect of organic-matter type and thermal maturity on methane adsorption in shale-gas systems

A series of methane (CH₄) adsorption experiments on bulk organic rich shales and their isolated kerogens were conducted at 35 °C, 50 °C and 65 °C and CH₄ pressure of up to 15 MPa under dry conditions. Samples from the Eocene Green River Formation, Devonian–Mississippian Woodford Shale and Upper Cretaceous Cameo coal were studied to examine how differences in organic matter type affect natural gas adsorption. Vitrinite reflectance values of these samples ranged from 0.56–0.58 %R_o. In addition, thermal maturity effects were determined on three Mississippian Barnett Shale samples with measured vitrinite reflectance values of 0.58, 0.81 and 2.01 %R_o.For all bulk and isolated kerogen samples, the total amount of methane adsorbed was directly proportional to the total organic carbon (TOC) content of the sample and the average maximum amount of gas sorption was 1.36 mmol of methane per gram of TOC. These results indicate that sorption on organic matter plays a critical role in shale-gas storage. Under the experimental conditions, differences in thermal maturity showed no significant effect on the total amount of gas sorbed. Experimental sorption isotherms could be fitted with good accuracy by the Langmuir function by adjusting the Langmuir pressure (P_L) and maximum sorption capacity (Γ_max). The lowest maturity sample (%R_o = 0.56) displayed a Langmuir pressure (P_L) of 5.15 MPa, significantly larger than the 2.33 MPa observed for the highest maturity (%R_o > 2.01) sample at 50 °C.The value of the Langmuir pressure (P_L) changes with kerogen type in the following sequence: type I > type II > type III. The thermodynamic parameters of CH₄ adsorption on organic rich shales were determined based on the experimental CH₄ isotherms. For the adsorption of CH₄ on organic rich shales and their isolated kerogen, the heat of adsorption (q) and the standard entropy (Δs⁰) range from 7.3–28.0 kJ/mol and from −36.2 to −92.2 J/mol/K, respectively.     

Mineralogical evidence for crystallization conditions and petrogenesis of ilmenite-series I-type granitoids at the Baogutu reduced porphyry Cu deposit (Western Junggar,NW China): Mössbauer spectroscopy,EPM and LA-(MC)-ICPMS analyses

Primary ore-forming minerals retain geochemical signatures of magmatic crystallization information and can reveal the petrochemical conditions prevalent at the time of their formation. The Baogutu deposit is a typical reduced porphyry Cu deposit. Amphibole and biotite Fe³⁺/ΣFe ratios, minerals (feldspar, biotite, amphibole, zircon and apatite), in situ elemental and apatite Nd isotopic compositions were determined by Mössbauer spectroscopy, electron probe microanalysis, and laser ablation multiple-collection inductively coupled plasma mass spectrometry, respectively, to investigate the magma oxidation state, petrogenesis, source features, and to constrain the carbon species at magmatic stages for the intrusive phases. The results show that the primary plagioclase and amphibole in the mineralized diorite to granodiorite porphyry and post ore hornblende diorite porphyry are distinct (An_26-55 versus An_60-69; Mg-hornblende versus tschermakite). In particular, the amphibole shows distinct major and trace element compositions with light rare earth element enrichments and negative Eu anomalies in Mg-hornblende and light rare earth element depletions and no Eu anomalies in tschermakite. All the analyzed biotites are primary igneous phases with a biotite phenocryst profile showing significant variations of Zn, Cr, Sc and Sr from core to rim. These results may indicate the occurrence of mixing between two distinct magmas during mineral formation. Titanium in zircon and Si¹ in amphibole thermometries indicate that magma crystallized at >900 °C and continued to ∼650 °C. In situ apatite Nd isotope (εNd(t) = 5.6–7.6, T_DM2 = 620–460 Ma), indicate absence of significant reduced sedimentary contamination and the source of juvenile lower crust. Slightly decreasing Fe³⁺/ΣFe ratios from biotite and amphibole to whole rock indicate decreasing oxygen fugacity during magma crystallization. Recalculated biotite compositions according to Fe³⁺/ΣFe ratios indicate fO₂ values of less than Ni-NiO buffer (NNO) which show slightly lower values than that estimated according to zircon/melt distribution coefficients Ce anomalies (∼ΔNNO + 0.6). These values are consistent with the features of reduced porphyry Cu deposits. Crystallization of other mineral phases significantly affects the reliability of oxybarometer of zircon/melt distribution coefficients Eu anomalies and Mn contents in apatite. This oxidation state suggests that only CO₂ was present at the magmatic stage, and implies that CH₄ formed during CO₂ reduction occurring later hydrothermal alteration. The alteration of primary amphibole to actinolite released Ti, Al, Fe, Mn, Na and K to the fluid with later precipitation of titanite, albite and minor ilmenite and magnetite during actinolite alteration.     

Laboratory chalcopyrite oxidation by Acidithiobacillus ferrooxidans: Oxygen and sulfur isotope fractionation

Laboratory experiments were conducted to simulate chalcopyrite oxidation under anaerobic and aerobic conditions in the absence or presence of the bacterium Acidithiobacillus ferrooxidans. Experiments were carried out with 3 different oxygen isotope values of water (δ¹⁸O_H2O) so that approach to equilibrium or steady-state isotope fractionation for different starting conditions could be evaluated. The contribution of dissolved O₂ and water-derived oxygen to dissolved sulfate formed by chalcopyrite oxidation was unambiguously resolved during the aerobic experiments. Aerobic oxidation of chalcopyrite showed 93 ± 1% incorporation of water oxygen into the resulting sulfate during the biological experiments. Anaerobic experiments showed similar percentages of water oxygen incorporation into sulfate, but were more variable. The experiments also allowed determination of sulfate–water oxygen isotope fractionation, ε¹⁸O_SO4–H2O, of ~ 3.8‰ for the anaerobic experiments. Aerobic oxidation produced apparent ε_SO4–H2O values (6.4‰) higher than the anaerobic experiments, possibly due to additional incorporation of dissolved O₂ into sulfate. δ³⁴S_SO4 values are ~ 4‰ lower than the parent sulfide mineral during anaerobic oxidation of chalcopyrite, with no significant difference between abiotic and biological processes. For the aerobic experiments, a small depletion in δ³⁴S_SO4 of ~? 1.5 ± 0.2‰ was observed for the biological experiments. Fewer solids precipitated during oxidation under aerobic conditions than under anaerobic conditions, which may account for the observed differences in sulfur isotope fractionation under these contrasting conditions.     

Effect of local soil conditions on dynamic ground response in the southern coast of Izmir Bay,Turkey

The city of Izmir, located at the western end of Turkey, has experienced many strong earthquakes throughout its history. The southern coast of Izmir Bay, one of the most densely populated areas of Izmir, is located on deep alluvial sediments. It is important to determine the effect of local soil conditions on dynamic ground response in the study area, where thick loose water-saturated alluvial sediments exist. A database including geotechnical and geological information on the study area is constructed. Majority of the site is classified as D and E according to NEHRP provisions. Dynamic site response analyses are performed with EERA by utilizing the field and laboratory test results and earthquake time histories of moderate-scale earthquakes such as 1977 Izmir (M_L = 5.3), 2003 Urla (M_d = 5.6), and 2005 Uzunkuyu-Urla (M_L = 5.9), which occurred in and nearby Izmir. In addition, a scenario ground motion generated by the Izmir Fault with a magnitude of 6.5, having an average distance of 10 km to the study area, is also considered. The output data obtained from the dynamic site response analyses are evaluated, and maps displaying variation in dynamic parameters on ground surface are prepared for the southern coast of Izmir Bay, Turkey. Consequently, the dynamic analyses performed with the soil models constituted for the study area verified the damage occurred in a close distance event of 1977 Izmir earthquake. The scenario earthquake resulted in peak ground accelerations more than 0.6 g at the eastern and western ends of the study area. However, long distance events resulted in spectral amplifications by up to 5 times. With this study, it is emphasized that local soil conditions should be evaluated individually in the area of interest. Generation of a site-specific design spectrum is recommended for the areas located on deep alluvial sediments.     

Compositional differences of chromophoric dissolved organic matter derived from phytoplankton and macrophytes

Chromophoric dissolved organic matter (CDOM) is an important component in the aquatic environment and plays a key role in light attenuation and in carbon biogeochemical cycles. We examined CDOM production in each of two laboratory experiments in which phytoplankton and macrophyte degradation were monitored using absorption and excitation–emission matrix fluorescence spectroscopy (EEMs). During the incubation period, CDOM was produced from phytoplankton and macrophytes, and partly decomposed by microorganisms. The absorption spectra of the phytoplankton derived and the macrophyte derived CDOM were distinct and characterized by peaks and shoulders in the UV bands. Production of CDOM absorption at 350 nm, a(350), was 0.0125 m²/g per unit of chlorophyll a from phytoplankton CDOM from 0–3 d. Meanwhile a(350) production was 2.708 × 10⁻⁴ m²/g per unit of wet biomass from macrophytes CDOM from 1–7 d. Despite the high production of CDOM by phytoplankton and macrophytes, extrapolation of these values to the field indicated that about 15% of total CDOM was produced from phytoplankton during algal blooms in Meiliang Bay in summer and about 8% of total CDOM was produced from macrophytes in the macrophyte dominated littorals. The mean value of the spectral slope (S) describing the exponential decrease of the absorption spectrum, which was strongly correlated to an optical index of molecular size, for the phytoplankton derived CDOM was 10.26 ± 2.05 μm⁻¹, which was significantly lower than the mean S of 14.47 ± 2.88 μm⁻¹ for the macrophyte derived CDOM (t-test, p < 0.001). The mean value of the spectral slope ratio (S_R) for the phytoplankton derived CDOM was 1.79 ± 0.52, which was significantly higher than that of 0.35 ± 0.58 for the macrophyte derived CDOM (t-test, p < 0.001). Three fluorescent components were validated in parallel factor analysis (PARAFAC) models calculated separately for phytoplankton derived and macrophyte derived CDOM, each CDOM source resulting in distinct excitation and emission maxima for each component. The significant differences in CDOM absorption spectra, S, S_R and PARAFAC fluorescence component characteristics, all showed that phytoplankton derived CDOM was compositionally distinct from macrophyte derived CDOM. Overall both sources were important to the CDOM pool in the shallow temperate lake.     

Enhancement of in situ biodegradation of organic compounds in groundwater by targeted pump and treat intervention

This study demonstrates the value of targeted pump and treatment (PAT) to enhance the in situ biodegradation of organic contaminants in groundwater for improved restoration. The approach is illustrated for a plume of phenolic compounds in a sandstone aquifer, where PAT is used for hydraulic containment and removal of dissolved phase contaminants from specific depth intervals. Time-series analysis of the plume hydrochemistry and stable isotope composition of dissolved species (δ³⁴S-SO₄, δ¹³C-CH₄, δ¹³C-TDIC (TDIC = Total Dissolved Inorganic Carbon)) in groundwater samples from high-resolution multilevel samplers were used to deduce changes in the relative significance of biodegradation processes and microbial activity in the plume, induced by the PAT system over 3 years. The PAT system has reduced the maximum contaminant concentrations (up to 6800 mg L⁻¹ total phenols) in the plume by 50% to ∼70% at different locations. This intervention has (i) stimulated in situ biodegradation in general, with an approximate doubling of contaminant turnover based on TDIC concentration, which has increased from <200 mg L⁻¹ to >350 mg L⁻¹, (ii) enhanced the activity of SO₄-reducing microorganisms (marked by a declining SO₄ concentration with corresponding increase in SO₄-δ³⁴S to values >7–14‰_V-CDT relative to background values of 1.9–6.5‰_V-CDT), and (iii) where the TDIC increase is greatest, has changed TDIC-δ¹³C from values of −10 to −15‰_V-PDB to ∼−20‰_V-PDB. This indicates an increase in the relative importance of respiration processes (including denitrification and anaerobic methane oxidation, AMO) that yield ¹³C-depleted TDIC over fermentation and acetoclastic methanogenesis that yield ¹³C-enriched TDIC in the plume, leading to higher contaminant turnover. The plume fringe was found to be a zone of enhanced biodegradation by SO₄-reduction and methanogenesis. Isotopically heavy methane compositions (up to −47.8‰_V-PDB) and trends between δ¹³C-TDIC and δ¹³C-CH₄ suggest that AMO occurs at the plume fringe where the contaminant concentrations have been reduced by the PAT system. Mass and isotope balances for inorganic carbon in the plume confirm the shift in spatial dominance of different biodegradation processes and significant increase in contribution of anaerobic respiration for contaminant biodegradation in zones targeted by the PAT system. The enhanced in situ biodegradation results from a reduction in organic contaminant concentrations in the plume to levels below those that formerly suppressed microbial activity, combined with increased supply of soluble electron acceptors (e.g. nitrate) into the plume by dispersion. An interruption of the PAT system and recovery of the dissolved organic contaminant concentrations towards former values highlights the dynamic nature of this enhancement on restoration and relatively rapid response of the aquifer microorganisms to changing conditions induced by the PAT system. In situ restoration using this combined engineered and passive approach has the potential to manage plumes of biodegradable contaminants over shorter timescales than would be possible using these methods independently. The application of PAT in this way strongly depends on the ability to ensure an adequate flux of dissolved electron acceptors into the plume by advection and dispersion, particularly in heterogeneous aquifers.     

ELNES spectroscopy of mixed Si coordination minerals

 Si K- and L-edge ELNES spectroscopy and multiple-scattering (MS) calculations are used to examine mixed Si coordination compounds varying in Si^VI:Si^IV ratio. As in previous studies, the edges are influenced mainly by silicon coordination (tetrahedral vs. octahedral), as supported by the MS calculations. We demonstrate two methods semi-quantitatively to extract the value of Si^VI/(Si^VI+Si^IV): (1) A linear relationship between the L_2,3-L₁ splitting and Si^VI/(Si^VI+Si^IV) is observed, (2) a fitting method based on the coaddition of reference tetrahedral and octahedral Si spectra is applied to both Si K- and L-edge ELNES spectra. Received: February 10, 1997 / Revised, accepted: May 23, 1997     

Diagenetic state and source characterization of marine sediments from the inner continental shelf of the Gulf of Cádiz (SW Spain), constrained by terrigenous biomarkers

Surface sediments from the Gulf of Cádiz (GoC) were analyzed by alkaline CuO oxidation, in order to estimate the contribution of terrigenous organic matter (TOM) to the inner continental shelf of the southwest Iberian Peninsula. The parallel analysis of sediment samples from the two most important rivers draining to this coastal area (i.e. Guadiana River and Tinto–Odiel fluvial system) provided fundamental information regarding local terrestrial sources. Relatively constant intensive lignin parameters (S:V = 1.0 ± 0.1 and C:V = 0.22 ± 0.04) and high values of the lignin phenol vegetation index (LPVI = 155 ± 43) indicated that non-woody angiosperm tissues constitute the dominant component of vascular plant material reaching the shelf sediments. The NW to SE decreasing isotopic (¹³C) and molecular (Λ₈) signatures found among the sediments, coinciding with the Guadiana delivery plume, suggest that this river is the main terrestrial source in the inner GoC shelf. Slightly elevated values of degradation indicative ratios ([Ad:Al]_V = 0.41 ± 0.10; [Ad:Al])_S = 0.34 ± 0.07; [3,5-Bd:V] = 0.14 ± 0.05; P:[V + S] = 0.24 ± 0.09) suggested the alteration state of the shelf sediments. The two fold higher ratios of the river sediments (Guadiana: [Ad:Al]_V = 0.82 ± 0.08; [Ad:Al]_S = 0.84 ± 0.03; Tinto–Odiel: [Ad:Al]_V = 0.86 ± 0.12; [Ad:Al]_S = 0.83 ± 0.013) and the increasing degradation trend observed outward in the shelf, lead us to consider preferential sorption processes, instead of in situ diagenesis, to affect the degradation signature of the shelf sediments. Preferentially solubilized degraded OM is more likely to be sorbed and stabilized prior to transport to the marine system, showing an apparently more advanced degradation state. The use of the 3,5-Bd:V ratio in conjunction with (Ad:Al)_V revealed a composition continuum of the sedimentary OM ranging from fresh plant materials to highly altered soil humic constituents. Elemental and molecular analyses show a land to sea gradient by a NW to SE decrease of the terrestrial influence, accounting for larger terrestrial inputs (TOM: 71–98%) in those sediments near the Guadiana mouth, and predominantly autochthonous composition (TOM: 42–50%) in those located offshore. This work utilizes lignin derived biomarkers to determine the contribution of terrigenous OM delivered to this poorly described coastal area from regional rivers. Within a context of increasing international efforts to better understand the global C cycling, this study illustrates the relevance of using the alkaline CuO oxidation approach to evaluate C budgets and continental influence in river dominated ocean margins.     

Magmatic evolution of the Tuwu–Yandong porphyry Cu belt,NW China: Constraints from geochronology,geochemistry and Sr–Nd–Hf isotopes

The Tuwu–Yandong porphyry Cu belt is located in the Eastern Tianshan mountains in the eastern Central Asian Orogenic Belt. Petrochemical and geochronological data for intrusive and volcanic rocks from the Tuwu and Yandong deposits are combined with previous studies to provide constraints on their petrogenesis and tectonic affinity. New LA–ICP–MS zircon U–Pb ages of 348.3 ± 6.0 Ma, 339.3 ± 2.2 Ma, 323.6 ± 2.5 Ma and 324.1 ± 2.3 Ma have been attained from intrusive units associated with the deposits, including diorite, plagiogranite porphyry, quartz albite porphyry and quartz porphyry, respectively. The basalt and andesite, which host part of the Cu mineralization, are tholeiitic with high Al₂O₃, Cr, Ni and low TiO₂ contents, enriched LREEs and negative HFSE (Nb, Ta, Zr, Ti) anomalies consistent with arc magmas. Diorites are characterized by low SiO₂ content but high MgO, Cr and Ni contents, similar to those of high-Mg andesites. The parental magma of the basalt, andesite and diorite is interpreted to have been derived from partial melting of mantle-wedge peridotite that was previously metasomatized by slab melts. The ore-bearing plagiogranite porphyry is characterized by high Na₂O, Sr, Cr and Ni contents, low Y and Yb contents, low Na₂O/K₂O ratios and high Sr/Y ratios and high Mg#, suggesting an adakitic affinity. The high ε_Nd(t) (5.02–9.16), low I_Sr (0.703219–0.704281) and high ε_Hf(t) (8.55–12.99) of the plagiogranite porphyry suggest they were derived by a partial melting of the subducted oceanic crust followed by adakitic melt-mantle peridotite interaction. The quartz albite porphyry and quartz porphyry are characterized by similar Sr–Nd–Hf isotope but lower Mg# and whole-rock (La/Yb)_N ratios to the plagiogranite porphyry, suggesting they were derived from juvenile lower crust, and negative Eu anomalies suggest fractionation of plagioclase. We propose that a flat subduction that started ca. 340 Ma and resulted in formation of the adakitic plagiogranite porphyry after a period of “steady” subduction, and experienced slab rollback at around 323 Ma.     

The spatial characteristics and pollution levels of metals in urban street dust of Beijing,China

The components and concentrations of metals in street dust are indictors of environmental pollution. To explore the pollution levels of Cd, Cr, Cu, Mn, Ni and Pb in street dust and their spatial distribution characteristics, 220 dust samples were collected in a grid pattern from urban street surfaces in Beijing. Multivariate statistics and spatial analyses were adopted to investigate the associations between metals and to identify their pollution patterns. In comparison with the soil background values, elevated metal concentrations were found, except those for Mn and Ni. The results of the geo-accumulation index (I_geo) and the potential ecological risk index (Erⁱ) of the metals revealed the following orders: Cd > Cu > Cr > Pb > Ni > Mn and Cd > Cu > Pb > Cr > Ni. Levels of I_geo ranging from 0 to 5 were found and about 80% of the samples were below the moderately polluted level. The Erⁱ values of single elements were within the low ecological risk level in most sampling sites. Most of the metals in the street dust of Beijing were statistically significantly correlated. It is hard to clearly identify the sources of each metal in the street dust since local environments are very complex. Cadmium, Cu, Cr, Mn and Pb showed medium spatial autocorrelations within the sampling region. Similar spatial distribution patterns were observed for Cu, Cr and Pb, and these metals had relatively high spatial variabilities and were enriched in the center of the city with several peaks scattered in the suburbs. Metal pollution anomalies were identified by using cluster and outlier analyses. Locations identified as clusters with high values indicated non-point source pollution, while locations identified as outliers with high values indicated point source pollution. Traffic, construction, and other human activities influenced these high values. In addition, the locations identified as outliers with low values in urban areas might benefit from less transportation and better management.     

Thermodynamic properties of tooeleite,Fe63+(As3+O3)4(SO4)(OH)4·4H2O

Tooeleite, nominally Fe₆³⁺(As³⁺O₃)₄(SO₄)(OH)₄·4H₂O, is a relatively uncommon mineral of some acid-mine drainage systems. Yet, if it does occur, it does so in large quantities, indicating that some specific conditions favor the formation of this mineral in the system Fe-As-S-O-H. In this contribution, we report the thermodynamic properties of synthetic tooeleite. The sample was characterized by powder X-ray diffraction, scanning electron microscopy, extended X-ray absorption fine-structure spectroscopy, and Mössbauer spectroscopy. These methods confirmed that the sample is pure, devoid of amorphous impurities of iron oxides, and that the oxidation state of arsenic is 3+. Using acid-solution calorimetry, the enthalpy of formation of this mineral from the elements at the standard conditions was determined as −6196.6 ± 8.6 kJ mol⁻¹. The entropy of tooeleite, calculated from low-temperature heat capacity data measured by relaxation calorimetry, is 899.0 ± 10.8 J mol⁻¹ K⁻¹. The calculated standard Gibbs free energy of formation is −5396.3 ± 9.3 kJ mol⁻¹. The log K_sp value, calculated for the reaction Fe₆(AsO₃)₄(SO₄)(OH)₄·4H₂O + 16H⁺ = 6Fe³⁺ + 4H₃AsO₃ + SO₄²⁻ + 8H₂O, is −17.25 ± 1.80. Tooeleite has stability field only at very high activities of aqueous sulfate and arsenate. As such, it does not appear to be a good candidate for arsenic immobilization at polluted sites. An inspection of speciation diagrams shows that the predominance field of Fe³⁺ and As³⁺ overlap only at strongly basic conditions. The formation of tooeleite, therefore, requires strictly selective oxidation of Fe²⁺ to Fe³⁺ and, at the same time, firm conservation of the trivalent oxidation state of arsenic. Such conditions can be realized only by biological systems (microorganisms) which can selectively oxidize one redox-active element but leave the other ones untouched. Hence, tooeleite is the first example of an “obligatory” biomineral under the conditions prevailing at or near the Earth's surface because its formation under these conditions necessitates the action of microorganisms.