Fracture pattern and electrical resistivity studies for groundwater exploration

 The occurrence, movement and control of groundwater, particularly in hard-rock areas, are governed by different factors such as topography, lithology, structures like fractures, faults and nature of weathering. An attempt is made in the present study to investigate the extent of the influence of structures such as fractures and thereby delineate the nature of subsurface lithology with the help of an electrical resistivity method. For this study, the Upper Gunjanaeru River basin, Cuddapah district Andhra Pradesh was chosen to determine groundwater potentials. In order to understand the significance of the fracture pattern, geological, hydrogeomorphological and lineament maps were prepared based on the field data and also from the LANDSAT TM imagery. Further, electrical resistivity surveys were conducted to determine the subsurface lithology and also to confirm the studies of LANDSAT imagery. The isoresistivity contour map has been prepared based on the 45 VES conducted to determine the resistivity variations in the study area. The isoresistivity contours obtained were found to conform to the structural trends obtained by geological studies and also confirm the relationship between the structure and secondary porosity present in the rocks. The lineaments in the area have two preferred directions. One set is a NE-SW direction (N 30°–70° E; S 30°–70° W) and another is a NW-SE direction (N 0°–30° W; S 0°–30° E and N 60°–80° W; S 60°–80° E). The water-table contour map shows that the direction of groundwater flow is south to north. Received: 3 March 1997 · Accepted: 17 June 1997     

Delineation of groundwater potential zone in Chhatna Block, Bankura District, West Bengal, India using remote sensing and GIS techniques

Groundwater is one of the most valuable natural resources, which is an immensely important and dependable source of water supply in all climatic regions over the world. Groundwater is in demand in areas where surface water supply is inadequate and nonsexist in the Chhatna Block, Bankura district and is located on the eastern slope of Chotonagpur Plateau, which is mapped on 73 I/15, 73 I/16 and 73 M/3, and falls between latitude 23°10′–23°30′N and longitude 86°47′–87°02′E. It represents plain land and gentle slope, which is responsible for infiltration and groundwater recharge. The groundwater in this region is confined within the fracture zones and weathered residuum. The present investigation is, therefore, undertaken to delineate potential zones for groundwater development with the help of a remote-sensing study. IRS–LISS-III data along with other data sets, e.g., existing toposheets and field observation data, have been utilized to extract information on the hydrogeomorphic features which include valley fills, buried pediment moderate, buried pediment shallow and structural hills, lineament density contour and slope map of this hard rock terrain. The target of this study is to delineate the groundwater potential zones in Chhatna block, Bankura District, West Bengal. Satellite imagery, along with other data sets, has been utilized to extract information on the groundwater controlling features of this study area. Three features (hydrogeomorphology, slope, and lineaments) that influence groundwater occurrences were analyzed and integrated. All the information layers have been integrated through GIS analysis and the groundwater potential zones have been delineated. The weighted index overlay method has been followed to delineate groundwater potential zones. The results indicate that good to excellent groundwater potential zones are available in almost the entire block. The results show that there is good agreement between the predicted groundwater potential map and the existing groundwater borehole databases. The area is characterized by hard rock terrain—still due to the presence of planation surface along valley fills; it became the prospective zone. The area has been categorized into four distinct zones: excellent, good, fair and poor. Excellent groundwater potential zones constitute 30–35 % of the total block area; good groundwater potential zones occupy a majority of the block, covering approximately 55–60 % and the fair potential zones occupy about 10–15 % of the total block. Poor potential zones occupy a very insignificant portion (less than 1 %).     

Soil-gas helium and surface-waves detection of fault zones in granitic bedrock

Fracture and fault networks are conduits that facilitate groundwater movement in hard-rock terrains. Soil-gas helium emanometry has been utilized in Wailapally watershed, near Hyderabad in southern India, for the detection of fracture and fault zones in a granite basement terrain having a thin regolith. Based on satellite imagery and geologic mapping, three sites were selected for detailed investigation. High spatial resolution soil-gas samples were collected at every one meter at a depth of >1.5m along 100m long profiles (3 in number). In addition, deep shear-wave images were also obtained using the multichannel analysis of surface waves. The study clearly indicates several soil-gas helium anomalies (above 200 ppb) along the profiles, where the shear-wave velocity images also show many near-surface vertical low velocity zones. We thus interpret that the soil-gas helium anomalous zones and the vertical low-velocity zones are probable traces of fault/fracture zones that could be efficient natural recharge zones and potential groundwater conduits. The result obtained from this study demonstrates the efficacy of an integrated approach of soil-gas helium and the seismic methods for mapping groundwater resource zones in granite/gneiss provinces.     

Fracture and stress orientation from borehole image logs: A case study from Cambay basin,India

The Deccan trap basalt, laid down by multiple lava flows during upper Cretaceous to Paleocene times forms the basement of current study in Cambay basin. As such, there is great interest and value in fracture detection and evaluation of fractured basement reservoirs in the Cambay basin. The procedure for identification and evaluation of natural as well as induced fractures in basaltic basement of the Cambay basin is presented in this work. In this study formation micro-imager (FMI) and extended range micro-imager (XRMI) log data for fracture identification is used. The Deccan trap basaltic basement of the study area, comprising five wells in the Tarapur-Cambay block, has potential for holding commercial hydrocarbon due to the presence of fractures and weathered basement. Both image logs (FMI, XRMI) identify three types of fracture including open (conductive), partially open and closed (resistive) fractures, of which open and partially open fractures are important for hydrocarbon accumulation. Fracture dip ranges from 10° to 80°. Image logs have also identified washout, breakout and drilling-induced fracture zones. The strike direction of the open natural fractures for four wells varies from N60°E to N30°E whereas the strike direction of most natural fracture in the fifth well is oriented towards N20°W. The orientations of drilling-induced fractures and breakouts may be interpreted for the in-situ stress direction over the logged interval. Drilling-induced tensile fractures, identified over the depth interval of 1969–1972 m, and borehole breakouts over the interval of 1953–1955 m in one well, suggest an orientation of maximum in-situ horizontal compressive stress (S_H) lies in the north-south direction. The azimuths of open natural fractures in the same well vary from north-south to N30°E. It is expected that the direction of fluid flow will be controlled by open natural fractures and therefore would be in a direction parallel to the S_H direction, which is orthogonal to the minimum horizontal stress (S_h) direction. The orientations observed are consistent with the present day S_H direction in the study area of Cambay basin.     

A climatological study of the relations among solar activity,galactic cosmic ray and precipitation on various regions over the globe

We apply Fourier and wavelet analyses to the precipitation and sunspot numbers in the time series (1901–2000) over Australia (27°S, 133°E), Canada (60°N, 95°W), Ethiopia (8°N, 38°E), Greenland (72°N, 40°W), United Kingdom (54°N, 2°W), India (20°N, 77°E), Iceland (65°N, 18°W), Japan (36°N, 138°E), United States (38°N, 97°W), South Africa (29°S, 24°E) and Russia (60°N, 100°E). Correlation analyses were also performed to find any relation among precipitation, sunspot numbers, temperature, and cloud-cover at the same spatial and temporal scale. Further correlations were also performed between precipitation with electron and proton fluence at the time interval, 1987–2006. All these parameters were considered in annual and seasonal scales. Though correlation study between precipitation and other parameters do not hint any linear relation, still the Fourier and wavelet analyses give an idea of common periodicities. The 9–11 year periodicity of sunspot numbers calculated by Fourier transform is also confirmed by wavelet transform in annual scale. Similarly, wavelet analysis for precipitation also supports the short periods at 2–5 years which is verified by Fourier transform in discontinuous time over different geographic regions.     

Geophysical imaging of municipal solid waste contaminant pathways

Surface electrical and electromagnetic surveys were conducted on top of a solid waste facility in Unguwan Dosa, Kaduna State, Northwest Nigeria. The aim of the geophysical survey was to detect vertical and subvertical fractures that may provide pathways for groundwater and contaminant transport. Results from the 2D electrical resistivity imaging showed vertical and subvertical contacts overlain by 6–10 m thick overburden. Quantitative interpretation of the VLF-EM data correlates well with the results of the 2D resistivity imaging delineating the vertical and subvertical contacts as good and weak conductors (fractures zones) with resistivity values of 40–220 and 300–420 Ω m, respectively. Azimuthal Schlumberger VES measurements yield apparent anisotropy values ranging from 1.01 to 1.47 for electrode spacings of 1–45 m with the highest value recorded at spacing of 2 m. However, azimuthal variations at large spacings (30–45 m) showed no fracture anisotropy due possibly to the array’s low sensitivity to anisotropy at these spacings. The result of the study showed that pollutants in the leachate can reach and contaminate the groundwater. Therefore, urgency for leachate treatment at this site is recommended to prevent contamination of groundwater.     

Fracture flow and groundwater compartmentalization in the Rollins Sandstone, Lower Mesaverde Group, Colorado, USA

 This paper presents a site-specific conceptual model of groundwater flow in fractured damage zones associated with faulting in a package of sedimentary rocks. The model is based on the results of field and laboratory investigations. Groundwater and methane gas inflows from fault-fracture systems in the West Elk coal mine, Colorado, USA, have occurred with increasing severity. Inflows of 6, 160 and 500 L s⁻¹ discharged almost instantaneously from three separate faults encountered in mine workings about 460 m below ground level. The faults are about 600 m apart. The δ ²H and δ ¹⁸O compositions of the fault-related inflow waters and the hydrodynamic responses of each fault inflow indicate that the groundwaters discharge from hydraulically isolated systems. ¹⁴C data indicate that the groundwaters are as much as 10,500 years old. Discharge temperatures are geothermal (≈30°C), which could indicate upwelling from depth. However, calculations of geothermal gradients, analysis of solute compositions of groundwater in potential host reservoirs, geothermometer calculations, and results of packer testing indicate that the fractured groundwater reservoir is the Rollins Sandstone (120 m thick) directly beneath the coal seams. The packer test also demonstrates that the methane gas is contained in the coal seams. A geothermal gradient of 70–80°C km⁻¹, related to an underlying intrusion, is probably responsible for the slightly elevated discharge temperatures. Large discharge volumes, as great as 8.2×10⁵m³ from the 14 South East Headgate fault (14 SEHG), rapid declines in discharge rates, and vertical and horizontal permeability (matrix permeability generally <0.006 Darcy) indicate fracture flow. An in-mine pumping test demonstrates that the 14 SEHG fault has excellent hydraulic communication with fractures 50 m from the fault. Aeromagnetic data indicate that the faults are tectonically related to an igneous body that is several thousand meters below the coal seams. Exploratory drilling has confirmed a fourth fault, and two additional faults are projected, based on the aeromagnetic data. The conceptual model describes a series of parallel, hydraulically separate groundwater systems associated with fault-specific damage zones. The faults are about 600 m apart. Groundwater stored in fractured sandstone is confined above and below by clayey layers. Received March 1999 / Revised, November 1999 / Accepted, December 1999     

Internal vein texture and vein evolution of the epithermal Shila-Paula district,southern Peru

The epithermal Shila-Paula Au–Ag district is characterized by numerous veins hosted in Tertiary volcanic rocks of the Western Cordillera (southern Peru). Field studies of the ore bodies reveal a systematic association of a main E–W vein with secondary N55–60°W veins—two directions that are also reflected by the orientation of fluid-inclusion planes in quartz crystals of the host rock. In areas where this pattern is not recognized, such as the Apacheta sector, vein emplacement seems to have been guided by regional N40°E and N40°W fractures. Two main vein-filling stages are identified. stage 1 is a quartz–adularia–pyrite–galena–sphalerite–chalcopyrite–electrum–Mn silicate–carbonate assemblage that fills the main E–W veins. stage 2, which contains most of the precious-metal mineralization, is divided into pre-bonanza and bonanza substages. The pre-bonanza substage consists of a quartz–adularia–carbonate assemblage that is observed within the secondary N45–60°W veins, in veinlets that cut the stage 1 assemblage, and in final open-space fillings. The two latter structures are finally filled by the bonanza substage characterized by a Fe-poor sphalerite–chalcopyrite–pyrite–galena–tennantite–tetrahedrite–polybasite–pearceite–electrum assemblage. The ore in the main veins is systematically brecciated, whereas the ore in the secondary veins and geodes is characteristic of open-space crystallization. Microthermometric measurements on sphalerite from both stages and on quartz and calcite from stage 2 indicate a salinity range of 0 to 15.5 wt% NaCl equivalent and homogenization temperatures bracketed between 200 and 330°C. Secondary CO₂-, N₂- and H₂S-bearing fluid inclusions are also identified. The age of vein emplacement, based on ⁴⁰Ar/³⁹Ar ages obtained on adularia of different veins, is estimated at around 11 Ma, with some overlap between adularia of stage 1 (11.4±0.4 Ma) and of stage 2 (10.8±0.3 Ma). A three-phase tectonic model has been constructed to explain the vein formation. Phase 1 corresponds to the assumed development of E–W sinistral shear zones and associated N60°W cleavages under the effects of a NE–SW shortening direction that is recognized at Andean scale. These structures contain the stage 1 ore assemblage that was brecciated during ongoing deformation. Phase 2 is a reactivation of earlier structures under a NW–SE shortening direction that allowed the reopening of the preexisting schistosity and the formation of scarce N50°E-striking S2-cleavage planes filled by the stage 2 pre-bonanza minerals. Phase 3 coincides with the bonanza ore emplacement in the secondary N45–60°W veins and also in open-space in the core of the main E–W veins. Our combined tectonic, textural, mineralogical, fluid-inclusion, and geochronological study presents a complete model of vein formation in which the reactivation of previously formed tectonic structures plays a significant role in ore formation.     

Structure of the low permeable naturally fractured geothermal reservoir at Soultz

The permeability of the granite geothermal reservoir of Soultz is primarily related to major fracture zones, which, in turn, are connected to dense networks of small-scale fractures. The small-scale fractures are nearly vertical and the major direction is about N0°E. This direction differs from that of the Rhine Graben, which is about N20°E to N45°E in northern Alsace. A total of 39 fracture zones, with a general strike of N160°E, have been identified in six wells between 1400 and 5000 m depth. These fracture zones are spatially concentrated in three clusters. The upper cluster at 1800–2000 m True Vertical Depth (TVD) is highly permeable. At 3000–3400 m TVD, the intermediate cluster in composed of a dense network developed in an altered matrix and forms the upper reservoir. In the lower part of the wells, the deeper cluster appears as a fractured reservoir developed within a low permeable matrix. Fracture zones represent a key element to take into account for predicting the geothermal reservoir life time submitted to various thermo-hydromechanical and chemical processes generated by hydraulic or chemical stimulations and by hydraulic circulation tests related to long-term exploitation.     

Denitrification capacity in a subterranean estuary below a Rhode Island fringing salt marsh

Coastal waters are severely threatened by nitrogen (N) loading from direct groundwater discharge. The subterranean estuary, the mixing zone of fresh groundwater and sea water in a coastal aquifer, has a high potential to remove substantial N. A network of piezometers was used to characterize the denitrification capacity and groundwater flow paths in the subterranean estuary below a Rhode Island fringing salt marsh.¹⁵N-enriched nitrate was injected into the subterranean estuary (in situ push-pull method) to evaluate the denitrification capacity of the saturated zone at multiple depths (125–300 cm) below different zones (upland-marsh transition zone, high marsh, and low marsh). From the upland to low marsh, the water table became shallower, groundwater dissolved oxygen decreased, and groundwater pH, soil organic carbon, and total root biomass increased. As groundwater approached the high and low marsh, the hydraulic gradient increased and deep groundwater upwelled. In the warm season (groundwater temperature >12 °C), elevated groundwater denitrification capacity within each zone was observed. The warm season low marsh groundwater denitrification capacity was significantly higher than all other zones and depths. In the cool season (groundwater temperature <10.5 °C), elevated groundwater denitrification capacity was only found in the low marsh. Additions of dissolved organic carbon did not alter groundwater denitrification capacity suggesting that an alternative electron donor, possibly transported by tidal inundation from the root zone, may be limiting. Combining flow paths with denitrification capacity and saturated porewater residence time, we estimated that as much as 29–60 mg N could be removed from 11 of water flowing through the subterranean estuary below the low marsh, arguing for the significance of subterranean estuaries in annual watershed scale N budgets.     

Mineralogy and geochemistry of El Dorado epithermal gold deposit, El Sauce district, central-northern Chile

Summary The El Dorado Au-Cu deposit is located in an extensive intra-caldera zone of hydrothermal alteration affecting Upper Cretaceous andesites of the Los Elquinos Formation at La Serena (≈ 29°47′S Lat., 70°43′W Long., Chile). Quartz-sulfide veins of economic potential are hosted by N25W and N20E fault structures associated with quartz-illite alteration (+supergene kaolinite). The main ore minerals in the deposit are pyrite, chalcopyrite ± fahlore (As/(As + Sb): 0.06−0.98), with electrum, sphalerite, galena, bournonite-seligmanite (As/(As + Sb): 0.21−0.31), marcasite, pyrrhotite being accessory phases. Electrum, with an Ag content between 32 and 37 at.%, occurs interstitial to pyrite aggregates or along pyrite fractures. Pyrite commonly exhibits chemical zonation with some zones up to 1.96 at.% As. Electron probe microanalyses of pyrite indicate that As-rich zones do not exhibit detectable Au values. Fluid inclusion microthermometry shows homogenization temperatures between 130 and 352 °C and salinities between 1.6 and 6.9 wt.% NaCl eq. Isotope data for quartz, ankerite and phyllosilicates and estimated temperatures show that δ¹⁸O and δD for the hydrothermal fluids were between 3 and 10‰ and between −95 and −75‰, respectively. These results suggest the mineralizing fluids were a mixture of meteoric and magmatic waters. An epithermal intermediate-sulfidation model is proposed for the formation of the El Dorado deposit. Author’s present address: J. Carrillo-Rosúa, Dpto. de Didáctica de las Ciencias Experimentales, Universidad de Granada, Campus de Cartuja, 18071, Granada, Spain     

New age constraints on the cooling and unroofing history of the Trans-Himalayan Ladakh Batholith (Kargil area), N. W. India

Thermotectonic history of the Trans-Himalayan Ladakh Batholith in the Kargil area, N. W. India, is inferred from new age data obtained here in conjunction with previously published ages. Fission-track (FT) ages on apatite fall around 20±2 Ma recording cooling through temperatures of ∼100°C and indicating an unroofing of 4 km of the Ladakh Range since the Early Miocene. Coexisting apatite and zircon FT ages from two samples in Kargil show the rocks to have cooled at an average rate of 5–6°C/Ma in the past 40 Ma. Zircon FT ages together with mica K−Ar cooling ages from the Ladakh Batholith cluster around 40–50 Ma, probably indicating an Eocene phase of uplift and erosion that affected the bulk of the batholith after the continental collision of India with the Ladakh arc at 55 Ma. Components of the granitoids in Upper Eocene-Lower Oligocene sediments of the Indus Molasse in Ladakh supports this idea. Three hornblende K−Ar ages of 90 Ma, 55 Ma, and 35 Ma are also reported; these distinctly different ages probably reflect cooling through 500–550°C of three phases of I-type plutonism in Ladakh also evidenced by other available radiometric data: 102 Ma (mid-Cretaceous), 60 Ma (Palaeocene), and 40 Ma (Late Eocene); the last phase being localised sheet injections. The geodynamic implications of the age data for the India-Asia collision are discussed.     

Integration of surface geophysical methods for fracture detection in crystalline bedrocks of southwestern Nigeria

The application of electrical imaging and very low frequency (VLF) electromagnetics was investigated for the purpose of delineating basement fracture zones, and to show how incorporating a priori information in numerical modelling would facilitate the location of fractured zones within a basement rock more precisely. To this end, direct current (DC) dipole–dipole resistivity and VLF modelling and inversion experiments were carried out to evaluate the efficacy of the methods in detecting low-resistivity fracture zones in a typical crystalline basement rock that is favourable for groundwater accumulation. Most wells drilled in such an environment usually have low yields. Results of the numerical experiment generally indicate that fractures covered by moderate overburden, and having considerable depth, extent, and thickness compared to the depth of fracture burial, produce good responses resulting in high-resolution resistivity images. Lower resolution resistivity images were obtained as the thickness of the overburden increased. Also, the model investigations indicate that width of the fracture zone plays a major role in controlling image resolution. Conclusions from the synthetic modelling were confirmed by resistivity and VLF data gathered across a suspected fault in a hard rock terrain of southwestern Nigeria. The results from the field data are in general agreement with the numerical modelling experiments.Integración de métodos geofísicos superficiales para la detección de fracturas en macizos rocosos cristalinos del suroeste de Nigeria.     

Identification of cross-valley faults in the Maynardville Limestone,Oak Ridge Reservation,Tennessee, using seismic refraction tomography

First arrival times from P-wave refraction and reflection seismic surveys along Bear Creek Valley on the Oak Ridge Reservation, Tennessee, were inverted to produce refraction tomographic velocity images showing seismic velocity variations within thinly mantled karstic bedrock to a depth of approximately 20 m. Inverted velocities are consistent with two distinct bedrock groups: the Nolichucky Shale (2,730–5,150 m/s) and Maynardville Limestone (3,940–7,575 m/s). Low-velocity zones (2,700–4,000 m/s) in the tomographic images correspond to previously inferred cross-valley strike-slip faults; in places, these faults create permeability barriers that offset or block groundwater flowing along Bear Creek Valley. These faults may also force groundwater contaminants, such as dense non-aqueous phase liquids, to migrate laterally or downward, spreading contamination throughout the groundwater system. Other, previously unmapped cross-valley faults may also be visible in the tomographic images. Borehole logs suggest the low-velocity values are caused by low rigidity fractured and vuggy rock, water zones, cavities and collapse features. Surface streams, including Bear Creek, tend to lie directly above these low-velocity zones, suggesting fault and fracture control of surface drainage, in addition to the subsurface flow system. In some cases, fault zones are also associated with bedrock depressions and thicker accumulations of unconsolidated sediment.     

Rock—Forming and Ore—Forming Temperatures of Lianhuashan Tungsten Deposit,Guangdong Province

The Lianhuashan tungsten deposit occurs in the volcanic terrain in the coastal area of Southeast China,where rhyolite,quartz porphyry and granite consitute a complee magmatic series.The orebodies are located in the endo-and exo-contacts between the quartz porphyry and the metasandstone of the Xiaoping coal measues.Hongenization temperatures of melt inclusions in zircon and quartz are 1100℃and 1050℃ for rhyolite,1000℃ and 860℃for quartz porphyry,and 950-1000℃and 820℃ for granite,respectively,demonstrating that the rockforming temperatures dropped successively from the eruptive to the intrusive rocks and that the homogenization temperatures of melt inclusions in zircon are 50-180℃higher than those in quartz.Homogenization temperatures of gas-liquid inclusions in quartz are 230-520℃（mostly 230-270℃）for quartz porphyry,200-450℃（mostly 200-360℃）for ore-bearing quartz veins,150-210℃for granite 170-200℃ for the vein quartz in it.Quartz from the quartz porphyry and from the ore-earing quartz veins show similar characteristics in inclusion type and homogenization temperature,indicating that intergranular solutions must have been formed upon cooling of magma and that ore-forming solutions for the tungstem mineralization were evolved mainly from ore-bearing intergranular solutions in the quartz porphyry.     

Control of regional structural styles and faulting on Northeast Mexico spring distribution

Groundwater-dependent, spring-fed ecosystems of the Cuatrociénegas Basin, Coahuila, Mexico, host >70 endemic species. These desert springs occur primarily aligned along the base of an anticline that bisects the Cuatrociénegas Basin, but the hydrogeologic controls of the springs are poorly understood. The hypothesis that spring locations are controlled by subsurface geology, such as buried anticlines or faulting, versus stratigraphic controls is tested by evaluating: (1) regional structural styles; (2) fracture models of analogous structures; (3) hydrogeologic data; and (4) geophysical surveys. Jurassic and Cretaceous siliciclastic and carbonate rocks deposited on the Coahuila Block west of the Cuatrociénegas Basin have dips <10° and lack faults because of a structurally rigid granodiorite basement. To the east of the Coahuila Block and around the Cuatrociénegas Basin, the Coahuila Folded Belt has anticlines associated with basement-involved faults, 10–25° backlimb dips, and forelimb dips up to vertical or slightly overturned. Springs in the western sub-basin that represent 85% of total basin discharge are located on zones of highest anticipated fracture density predicted by fracture models of analogous anticlines. Spring waters reveal elevated temperature (32–35°C) and low tritium (<1 tritium unit). Gravimetry and time-domain electromagnetic surveys correspond with a best-fit Cuatrociénegas Basin hydrogeologic model of fractures associated with reverse faulting controlling spring locations in the western Cuatrociénegas Basin. Springs in the eastern sub-basin are located where ephemeral streams have eroded through confining beds along the base of alluvial fans and lack faulting. Regional variations in structural style are an important control on the location of springs in the Cuatrociénegas Basin.     

Effects of fracture lineaments and in-situ rock stresses on groundwater flow in hard rocks: a case study from Sunnfjord, western Norway

Systematic field mapping of fracture lineaments observed on aerial photographs shows that almost all of these structures are positively correlated with zones of high macroscopic and mesoscopic fracture frequencies compared with the surroundings. The lineaments are subdivided into zones with different characteristics: (1) a central zone with fault rocks, high fracture frequency and connectivity but commonly with mineral sealed fractures, and (2) a damage zone divided into a proximal zone with a high fracture frequency of lineament parallel, non-mineralized and interconnected fractures, grading into a distal zone with lower fracture frequencies and which is transitional to the surrounding areas with general background fracturing. To examine the possible relations between lineament architecture and in-situ rock stress on groundwater flow, the geological fieldwork was followed up by in-situ stress measurements and test boreholes at selected sites. Geophysical well logging added valuable information about fracture distribution and fracture flow at depths. Based on the studies of in-situ stresses as well as the lineaments and associated fracture systems presented above, two working hypotheses for groundwater flow were formulated: (i) In areas with a general background fracturing and in the distal zone of lineaments, groundwater flow will mainly occur along fractures parallel with the largest in-situ rock stress, unless fractures are critically loaded or reactivated as shear fractures at angles around 30° to σ_H; (ii) In the influence area of lineaments, the largest potential for groundwater abstraction is in the proximal zone, where there is a high fracture frequency and connectivity with negligible fracture fillings. The testing of the two hypotheses does not give a clear and unequivocal answer in support of the two assumptions about groundwater flow in the study area. But most of the observed data are in agreement with the predictions from the models, and can be explained by the action of the present stress field on pre-existing fractures.     

Gradient profiling for the investigation of groundwater saturated fractures in hard rocks of Uttar Pradesh,India

Gradient profiling (GP) has been successfully utilized as a preliminary tool to identify fractured zones saturated with groundwater in hard-rock areas of Robertsganj, Sonebhadra district, Uttar Pradesh, India. Conducting geoelectrical sounding at randomly selected places may not provide fruitful results since fractures are sparsely distributed in hard rocks. In gradient profiling, current electrodes with large separation remain fixed while the potential dipole is moved between the current electrodes in the central one-third portion of the profile at a small station interval. A GP survey was conducted along seven profiles having different lengths in two small sectors of the study area. Low resistive zones have been identified which correspond to the fractured zones. A few geoelectrical soundings were carried out to investigate the depth and thickness of the fractured zones. Two test boreholes, one drilled in each sector, yielded continuous discharge of fresh water (18,000–24,000 L/h). The present study confirms the findings of previous work that the GP survey is a powerful initial technique that identifies the presence of a fractured zone, especially in a hard-rock area covered with a thin soil layer.     

Middle Miocene thermal metamorphism due to the infiltration of high-temperature fluid in the Sanbagawa metamorphic belt,southwest Japan

 The Middle Miocene Tobe hornfels in the Sanbagawa metamorphic belt, western Shikoku, southwest Japan, is characterized by an abnormally steep metamorphic gradient compared with other hornfelses associated with intrusive bodies. The basic hornfels, originally Sanbagawa greenschist rocks, is divided into the following three metamorphic zones: plagioclase, hornblende, and orthopyroxene. The plagioclase zone is defined by the appearance of calcic plagioclase, the hornblende zone by the assemblage of hornblende+calcic plagioclase+quartz, and the orthopyroxene zone is characterized by the assemblage of orthopyroxene + clinopyroxene + plagioclase + quartz. Calcic amphibole compositions change from actinolite to hornblende as a result of the continuous reactions during prograde metamorphism. Petrographical and thermometric studies indicate a metamorphic temperature range of 300–475°C for the plagioclase zone, 475–680°C for the hornblende zone, and 680–730°C for the orthopyroxene zone. The temperature gradient based on petrological studies is approximately 5°C/m, which is unusually high. Geological and petrological studies demonstrate that the hornfelses were formed by the focusing of high-temperature fluids through zones of relatively high fracture permeability. The steep thermal gradient in the Tobe hornfels body is consistent with a large fluid flux, greater than 8.3 × 10^–7 m³ m^–2S^–1, over the relatively short duration of metamorphism, approximately 100 years. Received: 10 October 1995 / Accepted: 28 May 1996     

The Variscan tectonic inheritance of the Upper Rhine Graben: evidence of reactivations in the Lias,Late Eocene–Oligocene up to the recent

Processing of gravity and magnetic maps shows that the basement of the Upper Rhine Graben area is characterized by a series of NE–SW trending discontinuities and elongated structures, identified in outcrops in the Vosges, Black Forest, and the Odenwald Mountains. They form a 40 km wide, N30–40° striking, sinistral wrench-zone that, in the Visean, shifted the Variscan and pre-Variscan structures by at least 43 km to the NE. Wrenching was associated with emplacement of several generations of plutonic bodies emplaced in the time range 340–325 Ma. The sub-vertical, NE–SW trending discontinuities in the basement acted as zones of weakness, susceptible to reactivation by subsequent tectonism. The first reactivation, marked by mineralizations and palaeomagnetic overprinting along NE–SW faults of the Vosges Mountains, results from the Liassic NW–SE extension contemporaneous with the break-up of Pangea. The major reactivation occurred during the Late Eocene N–S compression and the Early-Middle Oligocene E–W extension. The NE–SW striking basement discontinuities were successively reactivated as sinistral strike-slip faults, and as oblique normal faults. Elongated depocenters appear to form in association with reactivated Variscan wrench faults. Some of the recent earthquakes are located on NE–SW striking Variscan fault zones, and show sinistral strike-slip focal mechanisms with the same direction, suggesting also present reactivation.