关于防震减灾信息和辅助决策系统的安全性问题

根据防震减灾信息和辅助决策系统安全性的特点,具体分析了保证系统安全性的步骤和方法,并结合某分布式防震减灾信息和辅助决策系统框架,对其进行了安全性分析和安全性规划,制定了相应的安全性策略和措施,并介绍了可以进行安全性认证的国家权威机构,最后指出了防震减灾系统发展的趋势和存在的隐忧。     

郑州黄河大桥主桥自振特性分析

以京珠高速公路郑州黄河大桥主桥为研究对象，采用ANSYS有限元程序，建立了下承式钢管混凝土系杆拱桥的空间力学计算模型，利用子空间迭代法计算了该桥梁结构的自振周期和振型，对桥梁的模态特性进行了分析，计算结果可为该桥的设计、施工以及使用阶段的健康检测和维护提供技术参数和依据。     

云南强震动台网中心应用系统的设计与实现

云南数字强震动台网硬件系统建设完成后,有效的强震动台站维护和强震动数据处理应用是面临解决的首要问题。该文实现了云南强震动台网中心应用系统一系列的强震动业务系统应用,使得云南强震动台站自动检查和实时扫描、震动图自动生成（ShakeMap）、强震动台站建设资料、台站维护日志等系统通过应用系统实现无逢对接和集成,系统具有安全认证、信息发布、业务信息处理、外部系统接口4大类功能,为仪器维护人员和数据开发处理提供了一个强有力的平台支撑。该系统经过实际地震考验,有效地提高了强震动数据的处理。     

Particle size characteristics of suspended sediment in hillslope runoff and stream flow

This study examines the particle size characteristics of hillslope soils and fluvial suspended sediments in an agricultural catchment. Samples of surface runoff and stream flow were collected periodically and analysed for the size distributions of the effective (undispersed) sediment. This sediment was subsequently dispersed and the ultimate size distributions determined. The median effective particle size of stream suspended sediment was considerably coarser than the median ultimate particle size, indicating that most of the load included a substantial proportion of aggregates. Moreover, the proportion of fine material (i.e. silt and clay) increased, and the proportion of sand-sized material decreased, with increasing discharge. This decrease in sediment size with increased flow, which is contrary to the traditional assumption of a positive discharge/particle size relationship, is thought to reflect: (i) the influx of silt and clay, predominantly the former, originating on the catchment slopes and brought to the stream by overland flow along vehicle wheelings, roads and tracks; and (ii) erosion of fine material from the channel bed and banks. During large storms, however, the proportion of sand-sized sediment increased during the rising limb of the hydrograph, as a result of the entrainment of coarser source material from the valley floor during overbank flooding. The stream suspended sediment was finer than the catchment soils and considerably finer than material eroding from the catchment slopes during storms. The degree of clay and silt enrichment in the suspended sediments was largely the result of preferential deposition of the coarser fraction during the transport and delivery of sediment from its source to basin outlet. The data from this study confirm that a significant mode of sediment transport in fluvial systems is in the form of aggregates, and that the dispersed sediment size distribution is inappropriate for determining the transportability of sediment by flow. © 1997 by John Wiley & Sons, Ltd.     

基于迭代残差网络的双能CT图像材料分解研究

双能计算机断层成像技术(DECT)由于其材料分解能力,在高级成像应用中发挥着重要作用.图像域分解直接对CT图像进行线性矩阵反演,但分解后的材料图像会受到噪声和伪影的严重影响.虽然各种正则化方法被提出来解决这个问题,但它们仍然面临着两个挑战:繁琐的参数调整和过度平滑导致的图像细节损失.为此,本文提出一种基于迭代残差网络的...     

Neotectonic Crustal Uplift on the Continents and its Possible Mechanisms. The Case of Southern Africa

According to a large volume of data an intensive crustal uplift began in the Oligocene over most of the continental areas after a long period of relative tectonic stability. This Neotectonic uplift formed most of the present positive topographic features on the continents, and its strong acceleration took place during the last several million years. In many regions the uplift was associated with magmatism. The main methods of studying the Neotectonic uplift are considered together with the data on the uplift of Southern Africa. In this area the uplift took place in the Early Miocene (up to 300 m) and in the Late Pliocene and Pleistocene (up to 900 m). It occurred without stretching or shortening of the crust. Rapid erosion of the lower part of mantle lithosphere by a plume material is proposed as a mechanism of the uplift. This material ascended from below and rapidly spread along the base of the lithosphere. Its spreading for 1000 km during a few million years is possible only under a low viscosity of normal asthenosphere (1019 Pa s) and a much lower viscosity of a plume material (2 × 1016 Pa s). As in Southern Africa, in most of the regions the Neotectonic uplift was associated with insignificant shortening or stretching of the crust. This indicates that in some regions a plume material ascended from below and rapidly spread along the base of the lithosphere and eroded the mantle lithosphere in vast areas beneath the continents. In regions with a hot asthenosphere a strong weakening of the mantle lithosphere which allows its erosion can be associated with a high temperature of the plume material. In regions where the asthenosphere is at moderate temperature weakening of the mantle lithosphere can result from infiltration of volatiles from the plume material.     

Experimental and numerical analyses of vibrations induced by high-speed trains on the Córdoba–Málaga line

This paper has two main purposes. One is to present and analyse soil and structural vibration data obtained experimentally during certification testing of the high-speed train line between Córdoba and Málaga (Spain) that was opened on December 2007. The second is to show the capabilities of a three-dimensional boundary element method (BEM)/finite element method (FEM) numerical approach for the analysis of train induced vibrations. The model can represent local soil conditions, discontinuities such as underpasses, as well as structures placed next to the rail track. Vibrations in those structures can be computed taking into account, in a rigorous way, dynamic soil–structure interaction and local soil properties. Experimental and numerical results at several points near the track are compared. Results for an overhead contact support structure are also evaluated. The comparison of numerically predicted and recorded results shows that the model is reliable for predicting the amplitude of vibrations produced in the soil and nearby structures by high-speed trains.     

Determination of the material damping ratio and the shear wave velocity with the Seismic Cone Penetration Test

The Seismic Cone Penetration Test (SCPT) is used to determine the variation with depth of the shear (and longitudinal) wave velocity at various sites in Belgium. The cross correlation technique together with a posteriori increase of the sampling frequency proves to be a reliable method to determine wave velocities by the SCPT. Additionally, the Spectral Ratio Slope (SRS) method is applied to Fourier transforms of the measured response to determine the variation of the material damping ratio with depth. This method is applied to synthetic signals computed for three different soil profiles with known characteristics and to the horizontal acceleration time histories that have been measured during SCPT on two sites. The influence of some signal processing techniques commonly applied in the SRS method is studied. A remarkable influence of the window length, applied on the predicted signals, on the computed material damping ratio is found, especially its scattering. It is therefore concluded that the use of a window function should be avoided wherever possible. On one of the two test sites, results of Resonant Column Tests and Free Torsion Pendulum Tests on undisturbed soil samples have been used to evaluate the values of the shear wave velocity and the material damping ratio as obtained in the in situ test.     

细观结构对混凝土动态力学特性的影响研究

混凝土作为非均质复合材料,其力学特性受材料的微细观结构形态影响比较明显,物理试验很难将各因素孤立出来单独考虑其对混凝土力学特性的影响,本文从数值试验入手,把混凝土看作是由骨料、砂浆以及界面组成的三相材料,研究动压和动拉荷载作用下细观结构中诸如骨料位置、单元尺寸、材料强度以及骨料粒径对混凝土动态力学特性的影响,发现混凝土的细观结构对其动态力学特性有影响,不同因素对混凝土动态力学特性影响权重不同,相同因素在不同荷载作用下的影响结果也不同。     

Understanding airborne radiometric survey signals across part of eastern England

A low‐level airborne radiometric survey provides data on the concentrations of gammaemitting elements including potassium (K), thorium (Th) and uranium (U) in the upper half metre of the soil. Where weathering has not penetrated much beyond this depth, as in the young soils that cover much of England and Wales, the signal is likely to be related to the soil's clay content and its parent material. In these situations radiometric survey could be valuable for mapping soil digitally. We wished to understand how the radiometric signal relates to parent material and soil geochemistry, and to identify the spatial structure, if not the sources, of any unexplained variation. We analysed the joint spatial variation of the airborne gamma signal and high‐resolution soil geochemical survey data across part of eastern England by modelling their coregionalization. We also used reml to assess the joint effects of soil geochemistry and parent material on the radiometric signals of K and Th. The overall correlations of radiometric estimates with soil survey data for K and Th were large, as were the structural correlations for components of variation spatially dependent up to 49 and 16 km for K and Th respectively. This suggests that the radiometric signals for these two elements provide effective estimates of the amounts in the soil and their patterns of distribution. Although class of parent material accounted for a third of of the variance in the radiometric K signal, much of the variation within the classes is explained by geochemistry, suggesting that subtler changes can be detected. A larger proportion of the Th signal was accounted for by parent material. This supports our expectation that radiometric signals for K and Th provide information on parent material in the young landscapes of England and Wales. We are therefore confident that airborne radiometric surveys would be useful for making thematic maps of soil, particularly the soil's texture and closely related properties across England and Wales. Copyright © 2007 Natural Environment Research Council. Published in 2007 by John Wiley & Sons, Ltd.     

Study of seismic tomography in Panxi paleorift area of southwestern China--Structural features of crust and mantle and their evolution

Structural features of the typical continental paleorift in Panxiarea are revealed by seismic tomography. (1) In the profile along the minor axis of Panxi paleorift, we found alternating high and low-velocity strips existing at different depths in the crust, presenting itself as a "sandwich" structure. The existence of these high and low-velocity anomaly strips is related to the basal lithology in the rift area. (2) An addition layer with velocity values of 7.1-7.5 km/s and 7.8 km/s exists from the base of lower crust to uppermost mantle and its thickness is about 20 km. Some study results indicate that the addition layer results from the invasion of mantle material. (3) A lens-shaped high-velocity body surrounded by relatively low-velocity material is observed at depths of 110-160 km between Huaping and Huidong in the axis of the paleorift. This is the first time to discover it in the upper mantle of the paleorift. Based on the results of geology, petrology and geochemistry, we infer that the formation of the addition layer and the lens-shaped high-velocity body in the upper mantle are related to the deep geodynamic process of generation, development and termination of the rift. On the one hand, the upwelling of asthenosphere mantle caused partial melting, and then the basaltic magma from the partial melted material further resulted in underplating and formed the crustal addition layer. On the other hand, the high-density content of mineral facies was increased in the residual melted mass of intensely depleted upper mantle, formed by basalt withdrawing. The solid-melt medium in the depleted upper mantle was mainly an accumulation of garnet and peridotite because the heating effect of lithosphere was relatively weakened in the later riftogenesis, so that a lens-shaped high-density and high-velocity zone was produced in the upper mantle. The results indicate that the energy and material exchange between asthenosphere and lithosphere and remarkable underplating would have an important effect on the material state and propagation of seismic wave in the lower crust, crust-mantle interface, asthenosphere and lithosphere. This process possibly is an important mechanism on the growth of continental crust and the evolution of deep mantle.     

Study of seismic tomography in Panxi paleorift area of southwestern China Structural features of crust and mantle and their evolution

Structural features of the typical continental paleorift in Panxi area are revealed by seismic tomography. (1) In the profile along the minor axis of Panxi paleorift, we found alternating high and low-velocity strips existing at different depths in the crust, presenting itself as a “sandwich” structure. The existence of these high and low-velocity anomaly strips is related to the basal lithology in the rift area. (2) An addition layer with velocity values of 7.1-7.5 km/s and 7.8 km/s exists from the base of lower crust to uppermost mantle and its thickness is about 20 km. Some study results indicate that the addition layer results from the invasion of mantle material. (3) A lens-shaped high-velocity body surrounded by relatively low-velocity material is observed at depths of 110-160 km between Huaping and Huidong in the axis of the paleorift. This is the first time to discover it in the upper mantle of the paleorift. Based on the results of geology, petrology and geochemistry, we infer that the formation of the addition layer and the lens-shaped high-velocity body in the upper mantle are related to the deep geodynamic process of generation, development and termination of the rift. On the one hand, the upwelling of asthenosphere mantle caused partial melting, and then the basaltic magma from the partial melted material further resulted in underplating and formed the crustal addition layer. On the other hand, the high-density content of mineral facies was increased in the residual melted mass of intensely depleted upper mantle, formed by basalt withdrawing. The solid-melt medium in the depleted upper mantle was mainly an accumulation of garnet and peridotite because the heating effect of lithosphere was relatively weakened in the later riftogenesis, so that a lens-shaped high-density and high-velocity zone was produced in the upper mantle. The results indicate that the energy and material exchange between asthenosphere and lithosphere and remarkable underplating would have an important effect on the material state and propagation of seismic wave in the lower crust, crust-mantle interface, asthenosphere and lithosphere. This process possibly is an important mechanism on the growth of continental crust and the evolution of deep mantle.     

Major,minor and trace element abundances in samples from the Apollo 17 station 7 boulder: Implications for the origin of early lunar crustal rocks

Apollo 17 station 7 boulder consortia samples were analyzed for major and minor elements by a combined semimicro atomic absorption spectrophotometric and colorimetric procedure. Lithophile trace element abundances were determined by stable isotope dilution mass spectrometry. Three matrix types samples (77135, 77115, and 77075) were found to be KREEP-rich fragment-laden melts with analogues throughout the Apollo 17 landing site. Of the five clasts analyzed, at least one (77115,19, troctolite) is thought to be a cumulate; 77135, 77115, and 77075 are thought to have originated by impact fusion of material with similar composition. This original material may represent a partial melt of a parent material of the composition of an included, shocked norite breccia (77215).     

Dynamic microplasticity manifestation in consolidated sandstone in the acoustical frequency range

Microplasticity manifestations caused by acoustic wave in the frequency range of about 4.5 kHz–7.0 kHz are detected in consolidated artificial sandstone. Equipment was tested by means of comparison of data obtained for a standard material (aluminium) and sandstone. Microplasticity manifestations in acoustic records are present in the form of ladder‐like changes in the amplitude course. The stress plateaus in the acoustic trace interrupt the amplitude course, transform the wavefront, and shift the arrival time along the time axis. Microplasticity contribution to the acoustic record changes with the increase in the strain amplitude value. The combined elastic–microplastic process conditions the wavefront steepness and its duration. Stress plateaus exert influence on the waveform and, accordingly, on pulse frequency response. These results confirm the earlier data obtained for weakly consolidated rock. This contribution to wave propagation physics can be useful in solving applied problems in material science, seismic prospecting, diagnostics, etc.     

A new mixing equation for bed material composition in bed form dominant conditions

Vertical mixing beneath the bed surface and its effect on sediment composition has long been underestimated. This paper proposes a mixing equation to illustrate the temporal and spatial variations of bed material composition for bed form dominant rivers. A continuous mass conservation equation for elevation-specific nonuniform bed material composition is initially presented. A vertical mixing equation is finally derived as a diffusion-type partial differential equation with a source term charact...     

Numerical models for the seismic assessment of St. Nicholas Cathedral,Cyprus

Within the scope of this study, seismic performance of the St. Nicholas Cathedral that dates back to 1300s was assessed. This structure resembles to the Rheims Cathedral of France with a nave of seven bays ending in a polygonal apse, together with flanking aisles ending in apsidal chapels of similar shape. According to historical records, it sustained heavy earthquake damage twice to its roof structure and flying buttresses. The main construction material used at St. Nicholas Cathedral is calcarenite. With the non-destructive and uniaxial compression tests carried out, mechanical properties of the material used and their variability throughout the structure were documented. Based on the information gathered on the structure, its 3 dimensional finite element model was built. After calibrating this model with ambient vibration test results, seismic performance of the cathedral was assessed. Findings of this study suggested that it will sustain severe damage at its flying buttresses and flying buttress–vault connection points (part of the roof structure) under an earthquake of 475 year return period. Based on the obtained analytical results, a number of rehabilitation recommendations were made.     

Mantle transition zone structure beneath the Central Asian Orogenic Belt

Over the past decades, there have been hot debates in the geodynamic community regarding to the deep evolution mechanisms of Cenozoic volcanism in the Central Asian Orogenic Belt(CAOB). Of all the constraints available, high resolution structure of upper mantle discontinuities, especially the discontinuities at depths of 410 km(D410) and 660 km(D660), is of the most important, which may provide reliable clues on the magma channel as well as its evolution. In this work, we adopt the common conversion point stacking technique with teleseismic radial P-wave receiver functions to examine the D410 and D660 discontinuities. The primary results exhibit that the major characteristics of the mantle transition zone(MTZ) obtained by different velocity models are largely consistent. Obviously elevated D410 and slightly depressed D660 are observed beneath the Hannuoba Volcano, suggesting possible delamination of the local lithosphere deposited at the D410. This process may induce upwelling of the asthenospheric materials filling the space left by the delaminated lithosphere, and subsequently trigger volcanic eruptions. Strong depressions are observed at both D410 and D660 depths beneath west of the Dariganga Volcano, and the depression of D660 is more pronounced. It leads to the apparently thickened MTZ, indicating the presence of cold material at the D660. This cold material is speculated as a stagnant slab from the subducted Pacific Plate or the remains of a detached island arc system from the collision and formation of the CAOB. Slightly thinner MTZ is found beneath the Hentey Mountains and the Middle Gobi Volcano. Apparently, this thinner MTZ is not significant enough to support the existence of high thermal anomalies,which may rule out the possibility of large-scale hot material upwelling from either the local MTZ or even the lower mantle.     

Wave dispersion studies in granular media by analytical and analytical–numerical methods

The phenomenon of wave dispersion in dry sand is studied both by purely analytical studies and by analytical–numerical experiments on the basis of gradient elastic and viscoelastic material models. These material models are employed in order to simulate the microstructural characteristics of dry sand. The analytical studies treat the material body as a one-dimensional (for the viscoelastic case) and three-dimensional (for the gradient elastic case) and for both material models provide explicit expressions for the velocity of propagation of harmonic compressional (P) and shear (S) waves. These velocities are found to be functions of frequency, i.e., dispersive. The analytical–numerical studies treat the material as a one-dimensional one and try to simulate P and S wave propagation along the axial direction of cylindrical dry sand specimens. Thus, a sinusoidal pulse with a specific frequency is applied at one end of the specimen and the response is determined at some other point by solving a transient dynamic boundary value problem with the aid of a numerical Laplace transform. This analytical–numerical experiment is repeated for various frequencies. Thus, one determines the velocities of P and S waves as functions of frequency, thereby proving again that wave propagation in dry sand is dispersive.     

考虑材料损伤累积的型钢高强混凝土框架节点数值建模及参数分析

为研究地震作用下损伤累积对型钢高强混凝土框架节点抗震性能的影响,基于5榀型钢高强混凝土框架节点低周反复加载试验结果,分析节点构件损伤累积过程及其对刚度和强度的影响。从材料自身损伤入手,通过引入刚度影响系数考虑循环荷载作用下混凝土的单边效应,对Faria-Oliver本构模型进行改进,进而建立适应于型钢混凝土结构的材料损伤累积本构模型。同时基于该模型采用ANSYS分析软件对地震作用下的型钢高强混凝土框架节点进行数值分析,并与试验结果进行对比分析。结果表明:采用本文建立的材料损伤累积本构模型能较好地反映地震作用下型钢高强混凝土框架节点的损伤特性。在此基础上,进一步分析构件轴压比、配箍率、配钢率等设计参数对型钢高强混凝土框架节点抗震性能的影响。研究成果可为该类结构构件的抗震设计提供理论和技术支撑。