梁铰型屈服RC框架结构地震弹塑性位移增大系数研究

本文通过弹性和弹塑性时程分析,研究了水平地震作用下梁铰型屈服RC框架模型结构的楼层屈服剪力系数、基本自振周期、楼层数3个因素对弹塑性位移增大系数的影响,通过非线性回归分析给出了弹塑性层间位移增大系数经验公式;通过分析滞回耗能沿楼层高度的分布,初步确定了梁铰型屈服RC框架结构的薄弱楼层位置;基于结构损伤分析,讨论了抗震规范中RC框架结构弹塑性层间位移角限值的水准。     

罕遇地震下的屈曲约束支撑框架结构的动力响应研究

为分析支撑布置方式、刚度比、结构总层数等因素在罕遇地震下对屈曲约束支撑框架结构动力响应的影响,借助有限元分析软件SAP2000,分别对6层、12层、18层屈曲约束支撑框架结构模型进行了罕遇地震下的时程分析,详细研究了多高层结构体系的层间位移角、底层剪力、支撑内力等随支撑布置方式、刚度比、结构总层数等因素变化的规律。分析表明,倒V较单斜布置更能有效降低底层剪力、增大支撑轴力、降低层间位移角,从而降低结构的地震响应,更有利于结构消能减震;随着结构总层数的增大,支撑的屈服层数呈现出增多的趋势;刚度比七为2—4时,能使较多层数的屈曲约束支撑参与到消能减震的过程之中,较好地实现抗震设防目标。     

直接基于位移可靠度的抗震设计方法中目标位移代表值的确定

针对20多个现役结构，以基于力的抗震设计方法所求基底剪力与直接基于位移的抗震设计方法所求基底剪力相等为原则，回归给出了直接基于位移的抗震设计中基底剪力的调整系数。在此基础上，通过进一步分析，提出了直接基于位移可靠度的抗震设计中层间目标位移代表值的确定方法。最后，总结给出了直接基于位移可靠度的抗震设计步骤。     

钢筋混凝土框架结构直接基于位移的抗震设计

直接基于位移的抗震设计方法是对基于力的抗震设计方法的重大改进。按此方法进行设计时,需要解决的关键问题是确定结构的目标位移和相应的侧移模式。提出用框架梁节点截面屈服时的位移作为目标位移,并推导了层间屈服位移的计算公式;然后用结构近似的第一振型曲线作勾其侧移模式,对层间屈服位移进行修正。算例表明,本方法计算结果合理。     

最小剪力系数及其调整方法对超高层建筑地震响应的影响

超高层结构地震剪力响应由振型分解反应谱法得到的结果经常不能满足规定的最小剪力系数要求。为此,文章简述剪力系数的概念和调整方法,以具有不同剪力系数的两个模型对比分析结构弹性、弹塑性地震响应差异,探讨剪力系数对超高层结构地震响应的影响。以通过强度和刚度调整使最小剪力系数满足规范要求的两个模型,分析不同调整方法引起的结构响应的合理性。结果表明:满足最小剪力系数的结构的弹性基底剪力大、层间位移角较小,结构的弹塑性位移响应也较小,受力状态优于不满足最小剪力系数的结构,安全性得到了提高。结构弹性倾覆力矩需求和弹塑性基底剪力按刚度调整大于按强度调整;结构弹塑性最大顶点位移和层间位移角响应相差不大,但出现刚度大\,层间位移角也大的与抗震理论相悖的情况;在满足抗震要求的情况下,构件的受力状态则是按强度调整更优,构件截面更加经济合理。     

不同方法所求结构水平地震作用的比较

通过理论推导，分别给出了直接基于位移和直接基于位移可靠度两种抗震设计方法所求结构基底剪力与现行抗震规范所求结构基底剪力之比的数学表达式，分析了影响上述比值的主要因素及影响规律。     

一种直接基于位移的抗震设计方法

与传统基于力的抗震设计方法相比,基于位移的抗震设计方法更适合实现基于性能抗震设计。本文在若干文献的基础上,提出了一种直接基于位移的抗震设计方法。该方法建立在结构屈服位移可由几何尺寸确定的基础上,根据不同水平地震作用下的目标设计位移,计算相应的延性系数,采用一定的Rμ-μ-Tn关系建立相应的非线性反应谱,以二折线模型模拟结构的性能曲线,然后根据结构不同的目标位移以及对应的非线性反应谱确定相应的有效周期,从中选择最小值作为设计结构的有效周期,根据有效周期计算结构的刚度,然后乘以屈服位移得到结构的屈服强度。根据结构屈服强度以及结构的超强系数,得到结构的设计基底剪力。该方法避免了设计中采用迭代计算,且一次设计就可以完成多水平设防的目的。     

直接基于位移设计的高强钢组合K形偏心支撑钢框架的抗震性能研究

K形高强钢组合偏心支撑(K-HSS-EBF)是指耗能连梁和支撑采用Q345钢,而框架梁、框架柱采用高强度钢(如Q460)。为研究其在罕遇地震作用下的抗震性能,在试验研究的基础上,采用直接基于位移的抗震设计方法设计了5层、8层和12层算例,分别进行静力推覆分析和动力弹塑性分析,研究高强钢组合偏心支撑钢框架在罕遇地震作用下层间侧移分布和破坏模式。研究结果表明:直接基于位移的抗震设计方法设计的算例在罕遇地震作用下,结构的层间侧移满足我国现行抗震规范的要求,结构呈理想的渐进式梁铰屈服机构,并证明该设计方法的合理性和可靠性。     

剪力墙转换结构分析下建筑抗震性能研究

传统的动力弹塑性分析法在研究剪力墙的抗震性能时,忽略了对剪力墙转换结构关键结点的有效分析,导致建筑抗震性研究结果存在局限性。提出剪力墙转换结构关键结点对建筑抗震性能影响的分析方法。塑造剪力墙转换结构平面布置图,确定剪力墙转换结构关键结点,分析剪力墙转换结构关键结点的层间位移与位移角和关键结点处的楼层剪力,关键结点位置上升使得最大楼层的位移减小、位移角也逐渐变小。根据关键结点处于不同楼层时层间位移、位移角以及受力作用的不同,获取建筑结构上下层刚度的波动。实验结果说明,所提方法能够高精度、高效的对建筑抗震性能进行分析。     

新疆某既有框剪结构黏滞阻尼器减震加固设计

以新疆某12层钢筋混凝土框架剪力墙结构为例,采用消能减震技术进行加固改造,并进行了弹塑性动力时程分析。结果表明:首层剪力明显减小,X、Y方向层间位移均有不同程度的减小,因此,采用黏滞流体阻尼器使得该结构的抗震性能得到提升,满足现有抗震规范的要求。     

Influence of construction deficiencies on the seismic response of structures

The quality of construction is one of the main factors that affect the seismic vulnerability of structures. The damage observations of modern buildings after almost all recent earthquakes report cases of poor quality of materials, inadequate detailing of reinforcement and absence of capacity design principles. Looking at the modern codes for seismic design, which rely on high behaviour factor supplies, the assessment of the effects of poor quality of execution in otherwise well‐conceived and well‐designed structures becomes an important problem. This paper presents an experiment‐based estimation of the seismic response of a cast‐in‐situ one‐storey industrial reinforced concrete frame designed according to Eurocodes. The influence of the quality of construction is estimated by consideration of two models of the experimental prototype: a structure erected under strict measures for control of the quality of execution, and a structure erected with normal measures for control of the quality of execution which resulted in significant deficiencies in the practical arrangement of the reinforcement. On the basis of the experimental data the ductility and behaviour factor supplies of the two structures are estimated. Quantitative expressions for the influence of the quality of construction on the first yield displacement, ultimate storey displacement, maximum base‐shear force and behaviour factor supply are provided. Recommendations for the refinement of modern seismic design codes, particularly Eurocode 8, to take into account the quality of construction are given. Copyright © 2005 John Wiley & Sons, Ltd.     

钢框架结构的地震损伤研究

基于预定损伤法对钢框架构件主要设计参数进行损伤敏感度分析,研究主要设计参数与钢框架结构梁、柱损伤的关系;揭示钢框架结构梁、柱的损伤及梁、柱线刚度比、结构高宽比、柱轴压比、锈蚀率对楼层损伤的影响规律;获得楼层的损伤与整体结构损伤的关系,最终建立钢框架结构的损伤演化模型。研究成果可为建立地震激励下钢框架结构的损伤模型提供理论基础和数据支持。     

Statistical analysis of the inelastic response of shear structures subjected to earthquakes

Inelastic deformations of structures subjected to strong earthquakes are commonly accepted by Aseismic Codes; some discrepancies exist in the different procedures proposed to design a structure for which the ductility demand is to be limited within acceptable values. To have a better insight into the seismic behaviour of multi-degree-of-freedom structures beyond the elastic range, the dynamic elasto-plastic response of a ten-storey shear system under two sets of artificial and recorded accelerograms is studied considering different stiffness-strength distributions and constitutive laws. Statistics of the results are presented, demonstrating the dependence of the overall and storey ductility values and of their ratio on the characteristics of the structure and excitation.     

Study on a new shear wall system with shaking table test and finite element analysis

A new seismic energy dissipation shear wall structure is proposed in this paper. The new shear wall is one with purposely built‐in vertical slits within the wall panel, and rubber belts as seismic energy dissipation devices are installed in the vertical slits. In order to verify this concept, shaking table tests of a 10‐storey shear wall model with rubber belts filled in the vertical slits were carried out, and comparison of seismic behaviour was made between the new shear wall system and a shear wall with reinforced concrete connecting beams as energy dissipation. Furthermore, the seismic behaviour of this new shear wall is analysed by a finite element time history analysis method. The test and analysis show that the new shear wall system has a very good ability to dissipate seismic energy and is easy to use in engineering practice. Copyright © 2000 John Wiley & Sons, Ltd.     

Procedure to predict the storey where plastic drift dominates in two‐storey building under strong ground motion

A procedure is presented to predict the storey where plastic drift dominates in two‐storey buildings under strong ground motion. The procedure utilizes the yield strength and the mass of each storey as well as the peak ground acceleration. The procedure is based on two different assumptions: (1) the seismic force distribution is of inverted triangular form and (2) the rigid‐plastic model represents the system. The first and the second assumptions, respectively, lead to lower and upper estimates of the base shear coefficient under which the drift of the first storey exceeds that of the second storey. The efficiency of the procedure is verified by dynamic response analyses using elasto‐plastic model. Copyright © 2008 John Wiley & Sons, Ltd.     

非线性黏滞阻尼减震结构基于位移的设计方法

结合我国抗震设计规范,提出非线性黏滞阻尼减震结构基于位移的设计方法.根据减震结构的特点,将其性能划分为使用良好、人身安全和防止倒塌3个水平,并用层间位移角限值予以量化;以简化的方法计算非线性黏滞阻尼器的等效阻尼比.在此基础上将结构转化为等效单自由度体系,利用基于位移的设计方法对非线性黏滞阻尼减震结构进行设计,通过算例,介绍用该方法对框架结构进行非线性黏滞阻尼减震设计的设计过程.实例分析表明,提出的非线性黏滞阻尼减震结构基于位移的设计方法是可行的,并且与时程分析得出的平均结果吻合较好,而且该方法简单实用,便于操作,能够控制减震结构在不同强度水准地震作用下的性能.     

混凝土小砌块约束砌体结构的抗震性能——基于层间位移的分析

混凝土小砌块约束砌体结构,由于加入芯柱、构造柱、圈梁,使结构整体性提高,因此具有较好的抗震性能和发展前景。通过整理94个混凝土小砌块约束砌体墙片试验数据,考虑权重,统计了混凝土小砌块约束砌体墙片延性系数,给出了延性系数与高度、延性系数比与高宽的关系,同时给出了层间开裂位移角、层间极限位移角公式,以及接近倒塌时混凝土小砌块约束砌体结构层间位移的计算公式,并与一个八层混凝土小砌块约束砌体结构的动力时程分析结果进行了对比,结果显示,最大误差在顶层,为17.7%,因此,所提层间位移计算公式是可以满足工程精度需要的,为混凝土小砌块约束砌体结构基于性态的抗震分析提供参考。     

Mechanisms to limit higher mode effects in a controlled rocking steel frame. 1: Concept,modelling, and low‐amplitude shake table testing

Controlled rocking steel frames have been proposed as an efficient way to avoid the structural damage and residual deformations that are expected in conventional seismic force resisting systems. Although the base rocking response is intended to limit the force demands, higher mode effects can amplify member design forces, reducing the viability of the system. This paper suggests that seismic forces may be limited more effectively by providing multiple force‐limiting mechanisms. Two techniques are proposed: detailing one or more rocking joints above the base rocking joint and providing a self‐centring energy dissipative (SCED) brace at one or more levels. These concepts are applied to the design of an eight‐storey prototype structure and a shake table model at 30% scale. A simple numerical model that was used as a design tool is in good agreement with frequency characterization and low‐amplitude seismic tests of the shake table model, particularly when multiple force‐limiting mechanisms are active. These results suggest that the proposed mechanisms can enable better capacity design by reducing the variability of peak seismic force demands without causing excessive displacements. Similar results are expected for other systems that rely on a single location of concentrated nonlinearity to limit peak seismic loads. Copyright © 2012 John Wiley & Sons, Ltd.     

不同比例钢-混凝土混合结构高层建筑动力相似关系试验研究

模型试验的动力相似理论是结构抗震试验技术中的一个基础性研究课题。本文设计实现了1/10、1/20和1/30三个不同比例的钢-混凝土混合结构高层建筑的振动台模型试验。通过对三个模型试验结果的对比研究,对钢-混凝土混合结构高层建筑的动力相似关系进行了初步探讨。试验结果表明,按照本文的动力模型的设计施工及试验要求进行的不同比例钢-混凝土混合结构高层建筑的振动台试验,在自振频率、振型、加速度放大系数、楼层最大位移、楼层剪力等动力特性和动力反应方面具有较好的相似性。试验结果一方面说明对这三个模型采用的动力相似关系和制作方法是合理的,另一方面也说明了对钢-混凝土混合结构房屋采用较小的1/30比例进行振动台试验是可行的。     

安装形状记忆合金阻尼器的剪力墙结构抗震性能分析

为减轻钢筋混凝土剪力墙连梁的地震后永久性损伤,同时保持连梁的耗能机制,本文提出在剪力墙连梁中安装新型形状记忆合金(Shape Memory Alloy,简称SMA)阻尼器,并研究该阻尼器对剪力墙结构地震响应的减震效果。通过一幢12层剪力墙结构地震反应的时程分析,研究了SMA阻尼器的附加刚度比和屈服位移比两项特征参数对结构地震反应控制效果的影响规律。计算分析结果表明,当附加刚度比为0.04～0.05,屈服位移比为0.4～0.5时,可以获得较好的减震效果。