Real‐time hybrid testing of a smart base isolation system

Real‐time hybrid testing is a very effective technique for evaluating the dynamic responses of rate‐dependent structural systems subjected to earthquake excitation. A smart base isolation system has been proposed by others using conventional low‐damping isolators and controllable damping devices such as magnetorheological (MR) dampers to achieve specified control target performance. In this paper, real‐time hybrid tests of a smart base isolation system are conducted. The simulation is for a base‐isolated two‐degrees‐of‐freedom building model where the superstructure and the low‐damping base isolator are numerically simulated, and the MR damper is physically tested. The target displacement obtained from the step‐by‐step integration of the numerical substructure is imposed on the MR damper, which is driven by three different control algorithms in real‐time. To compensate the actuator delay and improve the accuracy of the test, an adaptive phase‐lead compensator is implemented. The accuracy of each test is investigated by using the root mean square error and the tracking indicator. Experimental results demonstrate that the hybrid testing procedure using the proposed actuator compensation techniques is effective for investigating the control performance of the MR damper in a smart base isolation system. Copyright © 2013 John Wiley & Sons, Ltd.     

Experimental investigation on the seismic response of a steel liquid storage tank equipped with floating roof by shaking table tests

In this paper, the effectiveness of the base isolation on steel storage tanks has been investigated through numerical models and then checked by shaking table tests on a reduced scale (1:14) model of a real steel tank, typically used in petrochemical plants. In the experimental campaign the floating roof has also been taken into account. The tests have been performed on the physical model both in fixed and isolated base configurations; in particular two alternative base isolation systems have been used: high‐damping rubber bearings devices and sliding isolators with elasto‐plastic dampers. Finally, a comparison between experimental and numerical results has also been performed. Copyright © 2009 John Wiley & Sons, Ltd.     

Shaking‐table tests on reinforced concrete frames with different isolation systems

The effectiveness of seismic isolation in protecting structural and non‐structural elements from damage has been assessed in an extensive programme of shaking‐table tests, carried out on four identical 1/3.3‐scale, two‐dimensional, reinforced concrete (R/C) frames. Four different isolation systems were considered, namely: (i) rubber‐based, (ii) steel‐based, (iii) shape memory alloy (SMA)‐based and (iv) hybrid, i.e. based on both SMA and steel components, isolation systems. This paper presents a comprehensive overview of the main results of the experimental tests on base‐isolated models, whose structural response is described through: (i) maximum base displacements; (ii) maximum interstorey drifts; (iii) maximum storey accelerations and (iv) maximum storey shear forces. The evolution of the fundamental frequency of vibration of the R/C frame during the tests is also described. The beneficial effects of using base isolation resulted in no or slight damage, under strong earthquakes, to both structural and non‐structural members, as well as to the internal content of the building. The comparison with the experimental results obtained in shaking‐table tests on similar fixed‐base models emphasizes these positive aspects. Finally, advantages and drawbacks related to the use of each isolation system are discussed in the paper. Copyright © 2006 John Wiley & Sons, Ltd.     

Appropriate viscous damping for nonlinear time‐history analysis of base‐isolated reinforced concrete buildings

There is no consensus at the present time regarding an appropriate approach to model viscous damping in nonlinear time‐history analysis of base‐isolated buildings because of uncertainties associated with quantification of energy dissipation. Therefore, in this study, the effects of modeling viscous damping on the response of base‐isolated reinforced concrete buildings subjected to earthquake ground motions are investigated. The test results of a reduced‐scale three‐story building previously tested on a shaking table are compared with three‐dimensional finite element simulation results. The study is primarily focused on nonlinear direct‐integration time‐history analysis, where many different approaches of modeling viscous damping, developed within the framework of Rayleigh damping are considered. Nonlinear direct‐integration time‐history analysis results reveal that the damping ratio as well as the approach used to model damping has significant effects on the response, and quite importantly, a damping ratio of 1% is more appropriate in simulating the response than a damping ratio of 5%. It is shown that stiffness‐proportional damping, where the coefficient multiplying the stiffness matrix is calculated from the frequency of the base‐isolated building with the post‐elastic stiffness of the isolation system, provides reasonable estimates of the peak response indicators, in addition to being able to capture the frequency content of the response very well. Furthermore, nonlinear modal time‐history analyses using constant as well as frequency‐dependent modal damping are also performed for comparison purposes. It was found that for nonlinear modal time‐history analysis, frequency‐dependent damping, where zero damping is assigned to the frequencies below the fundamental frequency of the superstructure for a fixed‐base condition and 5% damping is assigned to all other frequencies, is more appropriate, than 5% constant damping. Copyright © 2013 John Wiley & Sons, Ltd.     

Experimental investigation on a base isolation system incorporating steel–Teflon sliders and pressurized fluid viscous spring dampers

An experimental investigation on a base isolation system incorporating stainless steel–Teflon bearings as sliders, and pressurized fluid viscous spring dampers, is presented in this paper. In the system examined, dampers are connected to the base floor of an isolated building to provide the desired passive control of response in the superstructure, as well as to guarantee that it re‐centres completely after the termination of a seismic action. Two types of experiments were conducted: sinusoidal and random cyclic tests, and a pseudodynamic test in ‘substructured’ configuration. The cyclic tests were aimed at characterizing what follows: the hysteretic and strain‐rate‐dependent response of the considered highly non‐linear spring dampers; the normal pressure‐ and strain‐rate‐dependent frictional behaviour of steel–Teflon bearings, manufactured in compliance with the latest standards for this class of sliders; and the combined response of their assembly. The pseudodynamic test simulated the installation of the protection system at the base of a 2:3‐scale three‐storey steel frame structure, already tested in unprotected conditions by an earlier experimental campaign. Among other findings, the results of the performed tests, as well as of relevant mechanical interpretation and numerical simulation analyses, confirmed the linear additive combination of the dissipative actions of spring dampers and sliders in this mixed installation, and the high protective performance of the considered base isolation/supplemental damping system in a realistic earthquake simulation. Copyright © 2007 John Wiley & Sons, Ltd.     

Effects of near‐fault ground motions on the nonlinear dynamic response of base‐isolated r.c. framed buildings

Near‐fault ground motions are characterized by long‐period horizontal pulses and high values of the ratio between the peak value of the vertical acceleration, PGA_V, and the analogous value of the horizontal acceleration, PGA_H, which can become critical for base‐isolated (BI) structures. The objective of the present work is to check the effectiveness of the base isolation of framed buildings when using High‐Damping‐Rubber Bearings (HDRBs), taking into consideration the combined effects of the horizontal and vertical components of near‐fault ground motions. To this end, a numerical investigation is carried out with reference to BI reinforced concrete buildings designed according to the European seismic code (Eurocode 8). The design of the test structures is carried out in a high‐risk region considering (besides the gravity loads) the horizontal seismic loads acting alone or in combination with the vertical ones and assuming different values of the ratio between the vertical and horizontal stiffnesses of the HDRBs. The nonlinear seismic analysis is performed using a step‐by‐step procedure based on a two‐parameter implicit integration scheme and an initial‐stress‐like iterative procedure. At each step of the analysis, plastic conditions are checked at the potential critical sections of the girders (i.e. end sections of the sub‐elements in which a girder is discretized) and columns (i.e. end sections), where a bilinear moment–curvature law is adopted; the effect of the axial load on the ultimate bending moment (M‐N interaction) of the columns is also taken into account. The response of an HDRB is simulated by a model with variable stiffness properties in the horizontal and vertical directions, depending on the axial force and lateral deformation, and linear viscous damping. Copyright © 2011 John Wiley & Sons, Ltd.     

Component and shaking table tests for full‐scale multiple friction pendulum system

The use of base isolation in developed countries including the U.S. and Japan has already been recognized as a very effective method for upgrading the seismic resistance of structures. In this study, an advanced base‐isolation system called the multiple friction pendulum system (MFPS) is investigated to understand its performance on seismic mitigation through full‐scale component and shaking table tests. The component tests of the advanced Teflon composite coated on the sliding surface show that the friction coefficient of the lubricant material is a function of the sliding velocity in the range of 0.03–0.12. The experimental results also indicate that there were no signs of degradation of the sliding interface observed after 2000 cycles of sliding displacements. A full‐scale MFPS isolator under a vertically compressive load of 8830 KN (900 tf) and horizontally cyclic displacements was tested in order to assess the feasibility of the MFPS isolator for its practical use. After 248 cycles of horizontal displacement reversals, the behaviour of the base isolator was almost identical to its behaviour during the first few cycles. The experimental results of the shaking table tests of a full‐scale steel structure isolated with MFPS isolators show that the MFPS device can isolate seismic transmitted energy effectively under soft‐soil‐deposit site earthquakes with long predominant periods as well as strong ground motions with short predominant periods. These test results demonstrate that the MFPS isolator possesses excellent durability and outstanding earthquake‐proof capability. Furthermore, the numerical results show that the mathematical model proposed in this study can well predict the seismic responses of a structure isolated with MFPS isolators. Copyright © 2006 John Wiley & Sons, Ltd.     

Efficiency of base isolation systems in structural seismic protection and energetic assessment

This paper concerns the seismic response of structures isolated at the base by means of High Damping Rubber Bearings (HDRB). The analysis is performed by using a stochastic approach, and a Gaussian zero mean filtered non‐stationary stochastic process is used in order to model the seismic acceleration acting at the base of the structure. More precisely, the generalized Kanai–Tajimi model is adopted to describe the non‐stationary amplitude and frequency characteristics of the seismic motion. The hysteretic differential Bouc–Wen model (BWM) is adopted in order to take into account the non‐linear constitutive behaviour both of the base isolation device and of the structure. Moreover, the stochastic linearization method in the time domain is adopted to estimate the statistical moments of the non‐linear system response in the state space. The non‐linear differential equation of the response covariance matrix is then solved by using an iterative procedure which updates the coefficients of the equivalent linear system at each step and searches for the solution of the response covariance matrix equation. After the system response variance is estimated, a sensitivity analysis is carried out. The final aim of the research is to assess the real capacity of base isolation devices in order to protect the structures from seismic actions, by avoiding a non‐linear response, with associated large plastic displacements and, therefore, by limiting related damage phenomena in structural and non‐structural elements. In order to attain this objective the stochastic response of a non‐linear n‐dof shear‐type base‐isolated building is analysed; the constitutive law both of the structure and of the base devices is described, as previously reported, by adopting the BWM and by using appropriate parameters for this model, able to suitably characterize an ordinary building and the base isolators considered in the study. The protection level offered to the structure by the base isolators is then assessed by evaluating the reduction both of the displacement response and the hysteretic dissipated energy. Copyright © 2003 John Wiley & Sons, Ltd.     

On‐line hybrid test combining with general‐purpose finite element software

A new on‐line hybrid test system incorporated with the substructuring technique is developed. In this system, a general‐purpose finite element software is employed to obtain the restoring forces of the numerical substructure accurately. The restart option is repeatedly used to accommodate the software with alternating loading and analysis characteristic of the on‐line test but without touching the source code. An eight‐storey base‐isolated structure is tested to evaluate the feasibility and effectiveness of the proposed test system. The overall structure is divided into two substructures, i.e. a superstructure to be analysed by the software and a base‐isolation layer to be tested physically. Collisions between the base‐isolation layer and the surrounding walls are considered in the test. The responses of the overall structure are reasonable, and smooth operation is achieved without any malfunction. Copyright © 2006 John Wiley & Sons, Ltd.     

Investigation of the seismic response of high‐rise buildings supported on tension‐resistant elastomeric isolation bearings

In many applications of seismic isolation, such as in high‐rise construction, lightweight construction, and structures with large height‐to‐width aspect ratios, significant tension forces can develop in bearings, raising concerns about the possible rupture of elastomeric bearings and the uplift of sliding bearings. In this paper, a novel tension‐resistant lead plug rubber bearing (TLRB) with improved tension‐resisting capabilities is developed and experimentally and numerically assessed. This TLRB consists of a common lead plug rubber bearing (LRB) and several helical springs. After describing the theory underlying the behavior of the TLRB, the mechanical properties of reduced‐scale prototype bearings are investigated through extensive horizontal and vertical loading tests. The test results indicate that TLRBs can improve the shear stiffness and tension resistance capacity even under significant tensile loads. A series of shaking table tests on scaled models of high‐rise buildings with different aspect ratios were conducted to investigate the dynamic performance of the TLRB and the seismic responses of base‐isolated high‐rise buildings. Three different cases were considered in the shaking table tests: a fixed base condition and the use of TLRB and LRB isolation systems. The results of the shaking table test show that (a) base‐isolated systems are effective in reducing the structural responses of high‐rise buildings; (b) an isolated structure's aspect ratio is an important factor influencing its dynamic response; (c) TLRBs can endure large tensile stresses and avoid rupture on rubber bearings under strong earthquakes; and (d) the experimental and numerical results of the responses of the models show good agreement. Copyright © 2016 John Wiley & Sons, Ltd.     

Inelastic response of RC frame buildings with seismic isolation

A comprehensive parametric study on the inelastic seismic response of seismically isolated RC frame buildings, designed for gravity loads only, is presented. Four building prototypes, with 23 m × 10 m floor plan dimensions and number of storeys ranging from 2 to 8, are considered. All the buildings present internal resistant frames in one direction only, identified as the strong direction of the building. In the orthogonal weak direction, the buildings present outer resistant frames only, with infilled masonry panels. This structural configuration is typical of many existing RC buildings, realized in Italy and other European countries in the 60s and 70s. The parametric study is based on the results of extensive nonlinear response‐time history analyses of 2‐DOF systems, using a set of seven artificial and natural seismic ground motions. In the parametric study, buildings with strength ratio (F_y/W) ranging from 0.03 to 0.15 and post‐yield stiffness ratio ranging from 0% to 6% are examined. Three different types of isolation systems are considered, that is, high damping rubber bearings, lead rubber bearings and friction pendulum bearings. The isolation systems have been designed accepting the occurrence of plastic hinges in the superstructure during the design earthquake. The nonlinear response‐time history analyses results show that structures with seismic isolation experience fewer inelastic cycles compared with fixed‐base structures. As a consequence, although limited plastic deformations can be accepted, the collapse limit state of seismically isolated structures should be based on the lateral capacity of the superstructure without significant reliance on its inherent hysteretic damping or ductility capacity. Copyright © 2012 John Wiley & Sons, Ltd.     

1D joint multi‐offset inversion of time‐domain marine controlled source electromagnetic data

The accurate estimation of sub‐seafloor resistivity features from marine controlled source electromagnetic data using inverse modelling is hindered due to the limitations of the inversion routines. The most commonly used one‐dimensional inversion techniques for resolving subsurface resistivity structures are gradient‐based methods, namely Occam and Marquardt. The first approach relies on the smoothness of the model and is recommended when there are no sharp resistivity boundaries. The Marquardt routine is relevant for many electromagnetic applications with sharp resistivity contrasts but subject to the appropriate choice of a starting model. In this paper, we explore the ability of different 1D inversion schemes to derive sub‐seafloor resistivity structures from time domain marine controlled source electromagnetic data measured along an 8‐km‐long profile in the German North Sea. Seismic reflection data reveal a dipping shallow amplitude anomaly that was the target of the controleld source electromagnetic survey. We tested four inversion schemes to find suitable starting models for the final Marquardt inversion. In this respect, as a first scenario, Occam inversion results are considered a starting model for the subsequent Marquardt inversion (Occam–Marquardt). As a second scenario, we employ a global method called Differential Evolution Adaptive Metropolis and sequentially incorporate it with Marquardt inversion. The third approach corresponds to Marquardt inversion introducing lateral constraints. Finally, we include the lateral constraints in Differential Evolution Adaptive Metropolis optimization, and the results are sequentially utilized by Marquardt inversion. Occam–Marquardt may provide accurate estimation of the subsurface features, but it is dependent on the appropriate conversion of different multi‐layered Occam model to an acceptable starting model for Marquardt inversion, which is not straightforward. Employing parameter spaces, the Differential Evolution Adaptive Metropolis approach can be pertinent to determine Marquardt a priori information; nevertheless, the uncertainties in Differential Evolution Adaptive Metropolis optimization will introduce some inaccuracies in Marquardt inversion results. Laterally constrained Marquardt may be promising to resolve sub‐seafloor features, but it is not stable if there are significant lateral changes of the sub‐seafloor structure due to the dependence of the method to the starting model. Including the lateral constraints in Differential Evolution Adaptive Metropolis approach allows for faster convergence of the routine with consistent results, furnishing more accurate estimation of a priori models for the subsequent Marquardt inversion.     

Shake table testing of un‐reinforced brick masonry building test model isolated by U‐FREI

This paper presents a detailed study on feasibility of un‐bonded fiber reinforced elastomeric isolator (U‐FREI) as an alternative to steel reinforced elastomeric isolator (SREI) for seismic isolation of un‐reinforced masonry buildings. Un‐reinforced masonry buildings are inherently vulnerable under seismic excitation, and U‐FREIs are used for seismic isolation of such buildings in the present study. Shake table testing of a base isolated two storey un‐reinforced masonry building model subjected to four prescribed input excitations is carried out to ascertain its effectiveness in controlling seismic response. To compare the performance of U‐FREI, same building is placed directly on the shake table without isolator, and fixed base (FB) condition is simulated by restraining the base of the building with the shake table. Dynamic response characteristic of base isolated (BI) masonry building subjected to different intensities of input earthquakes is compared with the response of the same building without base isolation system. Acceleration response amplification and peak response values of test model with and without base isolation system are compared for different intensities of table acceleration. Distribution of shear forces and moment along the height of the structure and response time histories indicates significant reduction of dynamic responses of the structure with U‐FREI system. This study clearly demonstrates the improved seismic performance of un‐reinforced masonry building model supported on U‐FREIs under the action of considered ground motions. Copyright © 2015 John Wiley & Sons, Ltd.     

Experimental study of base isolation by free rolling rods

Experimental and analytical studies of base isolation by free rolling rods under basement are described in this paper. The tests of the system, a one-storey, 326-kg structure mounted on a set of free rolling rods, is carried out on a 3^m × 3^m shaking-table. The dynamic behaviour of the isolated structure is studied and used to verify the analytical results. In the isolation system, the coefficient of kinetic rolling friction, measured at different angular velocities, ranges from 0·0007 to 0·0016. The coefficients are reduced by decreasing the angular velocities. Two earthquakes, a short-period and a long-period motion in Taiwan, are utilized as the input signals. The accelerations experienced by the superstructure are decreased by factors of 56 and 60 in comparison with the fixed-base condition for the two input earthquakes. Also, for each test, the peak relative-to-ground displacement of the basement is nearly equal to the peak ground displacement, and the permanent displacement of the basement is present after the end of the earthquake. Finally, tests of the system with a recentring-force device is undertaken, where a soft spring added to the basement reduces efficiently the permanent displacement. Comparisons show a good agreement between experimental and theoretical results.     

Time domain identification of hybrid base isolation systems using free vibration tests

A procedure for the dynamic identification of the physical parameters of coupled base isolation systems is developed in the time domain. The isolation systems considered include high damping rubber bearings (HDRB) and low friction sliding bearings (LFSB). A bi‐linear hysteretic model is used alone or in parallel with a viscous damper to describe the behavior of the HDRB system, while a constant Coulomb friction device is used to model the LFSB system. After deriving the analytical dynamical solution for the coupled system under an imposed initial displacement, this is used in combination with the least‐squares method and an iterative procedure to identify the physical parameters of a given base isolation system belonging to the class described by the models considered. Performance and limitations of the proposed procedure are highlighted by numerical applications. The procedure is then applied to a real base isolation system using data from static and dynamic tests performed on a building at Solarino. The results of the proposed identification procedure have been compared to available laboratory data and the agreement is within ±10%. However, the need for improvement both in models and testing procedures also emerges from the numerical applications and results obtained. Copyright © 2010 John Wiley & Sons, Ltd.     

Dynamic analysis on structures base-isolated by a ball system with restoring property

A computational model with its analysis method for base-isolated structures by a ball system with restoring property under seismic force is proposed in this paper, and the programs using numerical integration method and incremental harmonic balance method are developed. The analysis method is verified by shaking table test results of a three-storey masonry model. With these programs, the effect of some factors on the aseismic behaviour of base isolation system are analysed, and the comparison of seismic response between structures with and without base isolation is made. Results of both theory and test show that the above-mentioned base isolation system has apparent advantages over the traditional aseismic structures. © 1998 John Wiley & Sons, Ltd.     

Semi‐active control of sliding isolated bridges using MR dampers: an experimental and numerical study

Sliding base‐isolation systems used in bridges reduce pier drifts, but at the expense of increased bearing displacements under near‐source pulse‐type earthquakes. It is common practice to incorporate supplemental passive non‐linear dampers into the isolation system to counter increased bearing displacements. Non‐linear passive dampers can certainly reduce bearing displacements, but only with increased isolation level forces and pier drifts. The semi‐active controllable non‐linear dampers, which can vary damping in real time, can reduce bearing displacements without further increase in forces and pier drifts; and hence deserve investigation. In this study performance of such a ‘smart’ sliding isolation system, used in a 1:20 scaled bridge model, employing semi‐active controllable magneto‐rheological (MR) dampers is investigated, analytically and experimentally, under several near‐fault earthquakes. A non‐linear analytical model, which incorporates the non‐linearities of sliding bearings and the MR damper, is developed. A Lyapunov control algorithm for control of the MR damper is developed and implemented in shake table tests. Analytical and shake table test results are compared. It is shown that the smart MR damper reduces bearing displacements further than the passive low‐ and high‐damping cases, while maintaining isolation level forces less than the passive high‐damping case. Copyright © 2005 John Wiley & Sons, Ltd.     

Shaking table test and analysis method on ultimate behavior of slender base‐isolated structure supported by laminated rubber bearings

This paper describes the results of shaking table tests to ascertain the ultimate behavior of slender base‐isolated buildings and proposes a time history response analysis method, which can predict the ultimate behavior of base‐isolated buildings caused by buckling fracture in laminated rubber bearings. In the tests, a base‐isolated structure model weighing 192 kN supported by four lead rubber bearings is used. The experimental parameters are the aspect ratio of height‐to‐distance between the bearings and the shape of and the axial stress on the bearings. The test results indicate that the motion types of the superstructure at large input levels can be classified into three types: the sinking type; the uplift type; and the mixed type. These behaviors depend on the relationship between the static ultimate lateral uplifting force on the superstructure and the lateral restoring characteristics of the base‐isolated story. In the analysis method, bearing characteristics are represented by a macroscopic mechanical model that is expanded by adding an axial spring to an existing model. Nonlinear spring characteristics are used for its rotational, shear, and axial spring. The central difference method is applied to solve the equation of motion. To verify the validity of the method, simulation analysis of the shaking table tests are carried out. The results of the analysis agree well with the test results. The proposed model can express the buckling behavior of bearings in the large deformation range. Copyright © 2010 John Wiley & Sons, Ltd.     

Online test using displacement–force mixed control

This paper proposes an online test technique that employs mixed control of displacement and force. Two types of mixed control, ‘displacement–force combined control’ and ‘displacement–force switching control’ are proposed. In displacement–force combined control, one jack is operated by displacement‐control, and another is operated by force‐control. Validity of the combined control technique is demonstrated by a series of online tests applied to a base‐isolated structure subjected to horizontal and vertical ground motions simultaneously. The substructuring technique is employed in the tests, and the base‐isolation layer is tested, with the rest of the structure modeled in the computer. Displacement‐control and force‐control were adopted for simulating the horizontal and vertical response, respectively. Both displacement‐ and force‐control were implemented successfully despite interference between the two jacks. Earthquake responses of the base‐isolated structure involving the effects of varying axial forces on the horizontal hysteretic behavior of the base‐isolation layer were simulated. In the displacement–force switching control, the jack was operated by displacement‐control when the test specimen was flexible but switched to force‐control once the specimen became stiff. Validity of the switching control technique was also checked by a series of online tests applied to the base‐isolated structure subjected to vertical ground motions. Switching between displacement‐control and force‐control was achieved when the axial force applied to the base‐isolation layer changed from tension to compression or from compression to tension. Both the displacement‐ and force‐control were successful even with many rounds of switching. The test revealed that large accelerations occurred on the floor immediately above the base‐isolation layer at the instants when the axial force of the base‐isolation layer changed from tension to compression. Copyright © 2005 John Wiley & Sons, Ltd.     

Experimental evaluation of piecewise exact solution for predicting seismic responses of spherical sliding type isolated structures

The use of base isolation for enhancing seismic resistibility has been proven as an efficient method in experimental and theoretical studies. It is usual to insert a flexible device in the horizontal direction to permit the most of relative deformation of a structure at this level. Because the rigidity of the superstructure is much higher than that of the base isolator underneath the structure, the behavior of the superstructure can be idealized as a rigid body during earthquakes. In general, hundreds of degrees of freedom and a step‐by‐step time history analysis are the basic requirements for calculating the seismic response of a base‐isolated structure under earthquakes. In order to develop a simple tool which can be easily adopted for calculating the seismic responses of the spherical sliding type isolated structures, a piecewise exact solution for predicting the seismic responses of base‐isolated structures has been derived in this study. The comparison between the experimental results conducted at the National Center for Research on Earthquake Engineering (NCREE) in Taiwan and the analytical results obtained from the piecewise exact solution show that the formulation derived in this study can predict the seismic responses of the base‐isolated structure with a very high accuracy. Copyright © 2005 John Wiley & Sons, Ltd.