首页 | 本学科首页   官方微博 | 高级检索  
相似文献
 共查询到20条相似文献,搜索用时 31 毫秒
1.
Seepage erosion in layered stream bank material   总被引:1,自引:0,他引:1  
Current stream restoration practices often require anthropogenic manipulation of natural field soils to reconstruct stream banks in the absence of stabilizing vegetation. For this study, researchers conducted laboratory experiments on reconstructed, non‐vegetated stream banks with layered soils experiencing seepage. The objective of the study was to determine the effect of seepage, pore water pressure, and bank geometry on erosion and bank stability of layered streambanks. The experimental design consisted of an intermediate‐size soil lysimeter packed with a sandy clay loam top soil and an underlying fine sand layer at three bank slopes (90°, 45° and 26°). Shallow groundwater flow and seepage resulted in bank failure of geometrically stable banks. Pop out failures, liquid deformation, and piping were all observed failure mechanisms in the underlying sand material, dependent on the bank angle. Groundwater seepage processes created small‐scale failures of the underlying sand leading to larger‐scale failures of the overlying sandy clay loam. The underlying sand layer eroded according to the initial bank angle and change in overburden loading. The overlying loam layer failed along linear failure planes. The gradually sloped bank (i.e. 26° slope) failed faster, hypothesized to be due to less confining pressure and greater vertical seepage forces. Researchers analyzed the laboratory experiments using the Bank Stability and Toe Erosion Model, version 4·1. The model calculated an accurate shear surface angle similar to the failure angle observed in the lysimeter tests. The model predicted failure only for the undercut 90° bank slope, and indicated stable conditions for the other geometries. Steeper initial bank slopes and undercut banks decreased the bank factor of safety. The observed failure mechanisms and measured saturation data indicated an interaction between overburden pressure, seepage forces, and bank slope on bank stability. Future bank stability modeling would benefit by incorporating lateral seepage erosion and soil liquefaction prediction calculations. Copyright © 2009 John Wiley & Sons, Ltd.  相似文献   

2.
This study examined the variation in soil erodibility along hillslopes in a Prairie landscape. The soil loss produced by simulated rainfall on undisturbed soils was used as an index of relative soil erodibility. Relative erodibility, and several soil properties, were measured at the summit, shoulder, midslope footslope and toeslope of 11 slope transects in an area of cultivated grassland soils on hummocky glacial till. The variation of erodibility with slope position was statistically significant, and slope position explained about 40 per cent of the variation in the erodibility measurements. Erodibility was 14 per cent higher on the shoulder and midslope, and 21 per cent lower on the toeslope, than on the summit and footslope. Local variation in erodibility along slopes was considered to be an important control on patterns of soil erosion in the landscape. The variation of erodibility along the slopes reflected soil property trends. The greatest erodibility was associated with upper slope positions where soils tended to be shallow, coarse, poorly leached and low in organic matter, while lower erodibility was found at lower slope positions with deep, organic-rich and leached soils. Of the individual soil properties considered, silt and sand content were the most highly correlated with erodibility. The results, together with results from other studies, also suggest that net erosion and erodibility are positively related.  相似文献   

3.
The interaction effects of different applied ratios of a hydrophilic polymer (Superab A200) (0, 0.2, 0.6% w/w) under various soil salinity levels (initial salinity, 4 and 8 ms/cm) were evaluated on available water content (AWC), biomass, and water use efficiency for corn grown in loamy sand and sandy clay loam soils. The results showed that the highest AWC was measured at the lowest soil salinity. The application of 0.6% w/w of the polymer at the lowest salinity level increased the AWC by 2.2 and 1.2 times greater than those of control in the loamy sand and sandy clay loam soils, respectively. The analysis of variance of data showed that the effect of salinity was significant on biomass and water use efficiency of corn in the loamy sand and sandy clay loam soils. The highest amounts of these traits were measured in soils with the lowest salinity level. Application of polymer at the rate of 0.6% in the loamy sand soil and at the rate of 0.2% in the sandy clay loam soil resulted in the highest aerial and root biomass and water use efficiency for corn. At these polymer rates the amounts of water use efficiency for corn were 2.6 and 1.7 times greater than those of control in the loamy sand and sandy clay loam soils, respectively. Thus, the use of hydrophilic polymer in soils especially in the sandy soils increases soil water holding capacity, yield, and water use efficiency of plant. On the other hand, decreases the negative effect of soil salinity on plant and helps for irrigation projects to succeed in arid and semi‐arid areas.  相似文献   

4.
Groundwater seepage can lead to the erosion and failure of streambanks and hillslopes. Two groundwater instability mechanisms include (i) tension failure due to the seepage force exceeding the soil shear strength or (ii) undercutting by seepage erosion and eventual mass failure. Previous research on these mechanisms has been limited to non‐cohesive and low cohesion soils. This study utilized a constant‐head, seepage soil box packed with more cohesive (6% and 15% clay) sandy loam soils at prescribed bulk densities (1.30 to 1.70 Mg m?3) and with a bank angle of 90° to investigate the controls on failure mechanisms due to seepage forces. A dimensionless seepage mechanism (SM) number was derived and evaluated based on the ratio of resistive cohesion forces to the driving forces leading to instability including seepage gradients with an assumed steady‐state seepage angle. Tension failures and undercutting were both observed dependent primarily on the saturated hydraulic conductivity, effective cohesion, and seepage gradient. Also, shapes of seepage undercuts for these more cohesive soils were wider and less deep compared to undercuts in sand and loamy sand soils. Direct shear tests were used to quantify the geotechnical properties of the soils packed at the various bulk densities. The SM number reasonably predicted the seepage failure mechanism (tension failure versus undercutting) based on the geotechnical properties and assumed steady‐state seepage gradients of the physical‐scale laboratory experiments, with some uncertainty due to measurement of geotechnical parameters, assumed seepage gradient direction, and the expected width of the failure block. It is hypothesized that the SM number can be used to evaluate seepage failure mechanisms when a streambank or hillslope experiences steady‐state seepage forces. When prevalent, seepage gradient forces should be considered when analyzing bank stability, and therefore should be incorporated into commonly used stability models. Copyright © 2013 John Wiley & Sons, Ltd.  相似文献   

5.
《国际泥沙研究》2023,38(1):49-65
Severe erosion is caused by intense rainfall in tropical regions. The erodible soil of steep hill slopes, accompanied by destruction of vegetation due to human interventions results in accelerated erosion. A sustainable and cost-effective solution such as vetiver grass (Chrysopogon zizanioides) is, thus, required to control the erosion process. In the current study, 6 small-scale glass models: 1 bare and 5 with vetiver grass, having a slope angle of 37° have been constructed. One year after planting, artificial rainfall of extremely high intensity was applied to all 6 small models and the role of vetiver canopy and roots in erosion and runoff control was observed. To see the effect of soil texture, one among these 5 models was made with silty sand and others contained sandy silt. The results demonstrated that, for sandy silt, the inclusion of vetiver reduced the soil loss by 94%–97%, and soil detachment rates were lowered by 95%. The average runoff also was reduced by 21%. The canopy cover showed a positive impact on reducing both quantities. An increase in average root diameter from 1.6 to 2.5 mm increases the soil loss due to its negative impact on added cohesion. The added cohesion showed a linearly negative correlation with soil loss. A composite system of vetiver and jute geotextile was most effective in erosion reduction among 4 vegetated models with sandy silt. Under same vetiver planting layout, the grass covered model of silty sand yielded 84% lower erosion and 62.5% lower runoff than the grass covered one with sandy silt. Thus, vetiver was more effective in erosion and runoff reduction for soil with a greater percentage of sand, and soil type dominated the erosion process.  相似文献   

6.
The objective of this study was to examine the possibility of determining soil erodibility of loamy soils with small flumes. This was done by comparing the classification of soil erodibility obtained in the field with that obtained in the laboratory. Therefore twenty soils with a texture varying from silty loam to sandy loam were selected from the Leuven region. The erosion in the field was determined by measuring the volumetric evolution of the rill pattern. In the laboratory the soils were tested with a rainfall simulator and small flumes. The conclusion was that for loamy soils the flume experiments are a quick, simple, and reliable method for the determination of the relative soil erodibility.  相似文献   

7.
Different hydraulic gradients, especially due to seepage or drainage, at different locations on a hillslope profile may have a profound effect on the dominant erosion processes. A laboratory study was designed to simulate hillslope processes and quantify effects of surface hydraulic gradients on erosion for a Glynwood clay loam soil (fine, illitic, mesic Aquic Hapludalf). A 5 m long, 1·2 m wide soil pan was used at 5 and 10 per cent slopes with an external watering tube to vary the soil bed's hydrological conditions. Different combinations of slope steepness with seepage or drainage gradients were used to simulate the hydrologic conditions on a 5 m segment of a hillslope profile. Runoff samples were taken during rainfall-only and rainfall with added inflow. Results showed that, under drainage conditions, interrill processes dominated and rilling was limited. The surface contained scattered crescent-shaped pits after the run. Under seepage conditions, rilling processes dominated and the inflow introduced at the top of the soil pan further accelerated the headward erosion of the rills. Erosion rates increased by as much as 60 times under seepage conditions representative of the lower backslope when compared to drainage conditions that generally occur at the upper backslope. This indicated that rills and gullies on backslopes and footslopes may be catalysed or enhanced by seepage conditions rather than form from flow hydraulic shear stress alone. An understanding of spatial and temporal changes that affect both hillslope hydrology and erosional processes is needed to develop accurate process-based erosion prediction models. This knowledge may lead to different management practices on landscape positions where seepage occurs. © 1998 John Wiley & Sons, Ltd.  相似文献   

8.
现场和实验室观测表明,一定黏粒含量的砂土在一定条件下易发生动力液化的现象,且黏粒含量对砂土抗液化性能的影响较为复杂。通过CKC全数字闭环控制气动式三轴仪试验系统,对黏粒含量为0%、5%和10%的砂土进行动力三轴试验。结果表明,黏粒含量为5%时砂土的抗液化性能最差,并且黏粒含量对于孔压的发展具有较大影响。根据实验数据的分析,对砂土-黏土的混合土的液化和抗液化性能进行机理分析。  相似文献   

9.
This paper describes laboratory testing of 148 samples collected from Southern Alberta for erosion by wash and splash. Rainfall intensity was held constant during these tests. Soil aggregation was the most significant variable explaining soil loss. The significance of other soil properties, such as organic carbon and clay content is variable, depending on the interrelationships among aggregate stability, organic content, and clay content of particular soils. Variations in erodibility of the major soils examined are explained by the resistance of aggregates to compaction and dispersion. Splash detachment and wash transport are the dominant erosion mechanisms in inter-rill areas.  相似文献   

10.
This study provides fundamental examination of mass fluvial erosion along a stream bank by identifying event timing, quantifying retreat lengths, and providing ranges of incipient shear stress for hydraulically driven erosion. Mass fluvial erosion is defined here as the detachment of thin soil layers or conglomerates from the bank face under higher hydraulic shear stresses relative to surface fluvial erosion, or the entrainment of individual grains or aggregates under lower hydraulic shear stresses. We explore the relationship between the two regimes in a representative, US Midwestern stream with semi‐cohesive bank soils, namely Clear Creek, IA. Photo‐Electronic Erosion Pins (PEEPs) provide, for the first time, in situ measurements of mass fluvial erosion retreat lengths during a season. The PEEPs were installed at identical locations where surface fluvial erosion measurements exist for identifying the transition point between the two regimes. This transition is postulated to occur when the applied shear stress surpasses a second threshold, namely the critical shear stress for mass fluvial erosion. We hypothesize that the regimes are intricately related and surface fluvial erosion can facilitate mass fluvial erosion. Selective entrainment of unbound/exposed, mostly silt‐sized particles at low shear stresses over sand‐sized sediment can armor the bank surface, limiting the removal of the underlying soil. The armoring here is enhanced by cementation from the presence of optimal levels of sand and clay. Select studies show that fluvial erosion strength can increase several‐fold when appropriate amounts of sand and clay are mixed and cement together. Hence, soil layers or conglomerates are entrained with higher flows. The critical shear stress for mass fluvial erosion was found to be an order of magnitude higher than that of surface fluvial erosion, and proceeded with higher (approximately 2–4 times) erodibility. The results were well represented by a mechanistic detachment model that captures the two regimes. Copyright © 2017 John Wiley & Sons, Ltd.  相似文献   

11.
The influence of small amounts of clay minerals on the hydraulic conductivity of sandy aquifer was investigated by laboratory experiments. Admixture of up to 1.5% by weight of clay minerals to sand did not cause any measurable decrease of hydraulic conductivity for seawater. Increasing the clay fraction from 1.5% to 10% decreased hydraulic conductivity by one order of magnitude. Montmorillonite caused the strongest decrease; the effect of kaolinite and illite was only half as large. When seawater was flushed by freshwater, hydraulic conductivity of the montmorillonite-sand mixture decreased drastically. However, flushing with freshwater did not measurably affect the hydraulic conductivity of an illite-sand or kaolinite-sand mixture. The explanation for this behaviour is the capability of various types of clay to adsorb different quantities of water between their platelets which induces a gel-droplet formation process. This is governed by the chemical composition and the ionic strength of the solution.  相似文献   

12.
Abstract

Abstract Water balances for a re-vegetated xerophyte shrub (Caragana korshinskii) area were compared to that of a bare surface area by using auto-weighing type lysimeters during the 1990–1995 growing seasons at the southeast Tengger Desert, Shapotou, China. The six-year experiment displayed how major daily water balance components might vary for a bare and a re-vegetated sand dune area. Evapotranspiration from the C. korshinskii lysimeter represented a major part of the water balance. The average annual ET/P ratios varied between 69 and 142%. No seepage was observed for the vegetated lysimeter. For the bare lysimeter, on the other hand, 48 mm or 27% of observed rainfall per year occurred as seepage. These results suggest that re-vegetating large sandy areas with xerophytic shrubs could reduce soil water storage by transpiration. Also, the experimental results indicate that re-vegetating large sandy areas could significantly change groundwater recharge conditions. However, from a viewpoint of desert ecosystem reconstruction, it appears that natural rainfall can sustain xerophytic shrubs such as C. korshinskii which would reduce erosion loss of sand. However, re-vegetation has to be balanced with recharge/groundwater needs of local populations.  相似文献   

13.
Sediment found in China’s Yangtze and Yellow River systems is characterized by large silt fractions. In contrast to sand and clay, sedimentation and erosion behaviour of silt and silt–clay–sand mixtures is relatively unknown. Therefore, settling and consolidation behaviour of silt-rich sediment from these river systems is analysed under laboratory conditions in specially designed settling columns. Results show that a transition in consolidation behaviour occurs around clay contents of about 10 %, which is in analogy with the transition from non-cohesive to cohesive erosion behaviour. Above this threshold, sediment mixtures consolidate in a cohesive way, whereas for smaller clay percentages only weak cohesive behaviour occurs. The settling behaviour of silt-rich sediment is found to be in analogy with granular material at concentration below 150 g/l. Above 150–200 g/l, the material settles in a hindered settling regime where segregation is limited or even prevented. The results indicate that for modelling purposes, multiple sediment fractions need to be assessed in order to produce accurate modelling results.  相似文献   

14.
Stochastic erosion of composite banks in alluvial river bends   总被引:2,自引:0,他引:2       下载免费PDF全文
The erosion of composite river banks is a complex process involving a number of factors including fluvial erosion, seepage erosion, and cantilever mass failure. To predict the rate of bank erosion with these complexities, a stochastic bank erosion model is suitable to define the probability distribution of the controlling variables. In this study, a bank erosion model in a river bend is developed by coupling several bank erosion processes with an existing hydrodynamic and morphological model. The soil erodibility of cohesive bank layers was measured using a submerged jet test apparatus. Seasonal bank erosion rates for four consecutive years at a bend in the Brahmaputra River, India, were measured by repeated bankline surveys. The ability of the model to predict erosion was evaluated in the river bend that displayed active bank erosion. In this study, different monsoon conditions and the distribution functions of two variables were considered in estimating the stochastic bank erosion rate: the probability of the soil erodibility and stochastic stage hydrographs for the nth return period river stage. Additionally, the influences of the deflection angle of the streamflow, longitudinal slope of river channel, and bed material size on bank erosion rate were also investigated. The obtained stochastic erosion predictions were compared with the observed distribution of the annual‐average bank erosion rate of 45 river bends in the Brahmaputra River. The developed model appropriately predicted the short‐term morphological dynamics of sand‐bed river bends with composite banks. Copyright © 2014 John Wiley & Sons, Ltd.  相似文献   

15.
Soil erosion is an important component of the global carbon cycle. However, little attention has been given to the role of aeolian processes in influencing soil organic carbon (SOC) flux and the release of greenhouse gasses, such as carbon dioxide (CO2), to the atmosphere. Understanding the magnitude and mechanisms of SOC enrichment in dust emissions is necessary to evaluate the impact of wind erosion on the carbon cycle. This research examines the SOC content and enrichment of dust emissions measured using Big Spring Number Eight (BSNE) wind‐vane samplers across five land types in the rangelands of western Queensland, Australia. Our results show that sandy soils and finer particulate quartz‐rich soils are more efficient at SOC emission and have larger SOC dust enrichment than clay‐rich aggregated soils. The SOC enrichment ratios of dusts originating from sites with sand‐rich soil ranged from 2·1–41·9, while the mean enrichment ratio for dusts originating from the clay soil was 2·1. We hypothesize that stronger inter‐particle bonds and the low grain density of the aggregated clay soil explain its reduced capacity to release SOC during saltation, relative to the particulate sandy soils. We also show that size‐selective sorting of SOC during transport may lead to further enrichment of SOC dust emissions. Two dust samples from regional transport events were found to contain 15–20% SOC. These preliminary results provide impetus for additional research into dust SOC enrichment processes to elucidate the impact of wind erosion on SOC flux and reduce uncertainty about the role of soil erosion in the global carbon cycle. Copyright © 2013 John Wiley & Sons, Ltd.  相似文献   

16.
The soil factor is crucial in controlling and properly modeling the initiation and development of ephemeral gullies (EGs). Usually, EG initiation has been related to various soil properties (i.e. sealing, critical shear stress, moisture, texture, etc.); meanwhile, the total growth of each EG (erosion rate) has been linked with proper soil erodibility. But, despite the studies to determine the influence of soil erodibility on (ephemeral) gully erosion, a universal approach is still lacking. This is due to the complex relationship and interactions between soil properties and the erosive process. A feasible soil characterization of EG erosion prediction on a large scale should be based on simple, quick and inexpensive tests to perform. The objective of this study was to identify and assess the soil properties – easily and quickly to determine – which best reflect soil erodibility on EG erosion. Forty‐nine different physical–chemical soil properties that may participate in establishing soil erodibility were determined on agricultural soils affected by the formation of EGs in Spain and Italy. Experiments were conducted in the laboratory and in the field (in the vicinity of the erosion paths). Because of its importance in controlling EG erosion, five variables related to antecedent moisture prior to the event that generated the gullies and two properties related to landscape topography were obtained for each situation. The most relevant variables were detected using multivariate analysis. The results defined 13 key variables: water content before the initiation of EGs, organic matter content, cation exchange capacity, relative sealing index, two granulometric and organic matter indices, seal permeability, aggregates stability (three index), crust penetration resistance, shear strength and an erodibility index obtained from the Jet Test erosion apparatus. The latter is proposed as a useful technique to evaluate and predict soil loss caused by EG erosion. Copyright © 2018 John Wiley & Sons, Ltd.  相似文献   

17.
目前相关规范主要依据工程场地单点的测试数据进行砂土液化判别,而实际的三维土层结构可能非常复杂。研究土层结构对砂土液化的影响机制,有利于提高砂土液化判别结果准确度。分析2008 年5 月28 日发生的松原MS地震和2010—2011 年新西兰坎特伯雷地震序列中砂土液化点的分布,结果显示:砂土液化点主要位于高弯度河流的沉积相地层,凹岸侧蚀、凸岸沉积形成的边滩具有典型的二元结构,其顶部分布的黏土类不透水层有利于下伏饱和粉细砂等易液化土层的超孔隙水压累积;而辫状河流沉积相中,上覆黏土类不透水层间断分布特征明显。针对河流不同沉积相的土层结构建立简化场地模型,使用FLAC3D 进行砂土液化数值模拟,揭示出不同土层结构中超孔隙水压力的累积、消散和渗流过程机制,结果表明,河流沉积相土层结构对砂土液化场点的分布和地表变形具有显著影响。在合理的工程地质分区基础上,现有的液化判别方法有必要考虑场地的土层结构的影响。   相似文献   

18.
The migration of groundwater in rock and soil can appear as abnormalities in geoelectric fields. It is therefore important to study the characteristics of seepage in porous media by measuring the geoelectric field signatures. In this study, a physical model with layers of sand and clay was constructed and an electrical resistivity meter was used to examine the changes in the geoelectric field parameters during the infiltration process. The results show that the infiltration could be detected based on the geoelectric signatures including temporal changes through the spontaneous potential, excitation currents, and apparent resistivity. Specifically, the spontaneous potential was reduced by 100 to 200 mV when the water reaches an electrode. During the second water injection in the experiment, the measured spontaneous potential of all the electrodes recovered to the previous extreme values that range from −200 to −550 mV, thus indicating a “memory” effect. With stepwise changes in the excitation current, it was possible to determine the seepage velocity in sand and clay layer. The apparent resistivity is reduced to less than 400 Ωm when the infiltration reaches the electrodes. These results indicate the potential for real-time monitoring of water flow.  相似文献   

19.
Mechanistic models have been proposed for soil piping and internal erosion on well‐compacted levees and dams, but limited research has evaluated these models in less compacted (more erodible) soils typical of hillslopes and streambanks. This study utilized a soil box (50 cm long, 50 cm wide and 20 cm tall) to conduct constant‐head, soil pipe and internal erosion experiments for two soils (clay loam from Dry Creek and sandy loam from Cow Creek streambanks) packed at uniform bulk densities. Initial gravimetric moisture contents prior to packing were 10, 12 and 14% for Dry Creek soil and 8, 12, and 14% for Cow Creek soil. A 1‐cm diameter rod was placed horizontally along the length of the soil bed during packing and carefully removed after packing to create a continuous soil pipe. A constant head was maintained at the inflow end. Flow rates and sediment concentrations were measured from the pipe outlet. Replicate submerged jet erosion tests (JETs) were conducted to derive erodibility parameters for repacked samples at the same moisture contents. Flow rates from the box experiments were used to calibrate the mechanistic model. The influence of the initial moisture content was apparent, with some pipes (8% moisture content) expanding so fast that limited data was collected. The mechanistic model was able to estimate equivalent flow rates to those observed in the experiments, but had difficulty matching observed sediment concentrations when the pipes rapidly expanded. The JETs predicted similar erodibility coefficients compared to the mechanistic model for the more erodible cases but not for the less erodible cases (14% moisture content). Improved models are needed that better define the changing soil pipe cross‐section during supply‐ and transport‐limited internal erosion, especially for piping through lower compacted (more erodible) soils as opposed to more well‐compacted soils resulting from constructing levees and dams. Copyright © 2013 John Wiley & Sons, Ltd.  相似文献   

20.
The surface susceptibility to erosion (erodibility) is an important component of soil erosion models. Many studies of wind erosion have shown that even relatively small changes in surface conditions can have a considerable effect on the temporal and spatial variability of dust emissions. One of the main difficulties in measuring erodibility is that it is controlled by a number of highly variable soil factors. Collection of these data is often limited in scale because in situ measurements are labour‐intensive and very time‐consuming. To improve wind erosion model predictions over several spatial and temporal scales simultaneously, there is a requirement for a non‐invasive approach that can be used to rapidly assess changes in the compositional and structural nature of a soil surface in time and space. Spectral reflectance of the soil surface appears to meet these desirable requirements and it is controlled by properties that affect the soil erodibility. Three soil surfaces were modified using rainfall simulation and wind tunnel abrasion experiments. Observations of those changes were made and recorded using digital images and on‐nadir spectral reflectance. The results showed clear evidence of the information content in the spectral domain that was otherwise difficult to interpret given the complicated interrelationships between soil composition and structure. Changes detected at the soil surface included the presence of a crust produced by rainsplash, the production of loose erodible material covering a rain crust and the selective erosion of the soil surface. The effect of rainsplash and aeolian abrasion was different for each soil tested and crust abrasion was shown to decrease as rainfall intensity increased. The relative contributions of the eroded material from each soil surface to trapped mixtures of material assisted the erodibility assessment. Ordination analyses within each of two important soil types explained significant amounts of the variation in the reflectance of all wavebands by treatments of the soil and hence changes in the soil surface. The results show that soil surface conditions within a soil type are an underestimated source of variation in the characterization of soil surface erodibility and in the remote sensing of soil. Copyright © 2005 John Wiley & Sons, Ltd.  相似文献   

设为首页 | 免责声明 | 关于勤云 | 加入收藏

Copyright©北京勤云科技发展有限公司  京ICP备09084417号