Erodibility of fine soil from the composite river bank of Brahmaputra in India

The erosion of a composite river bank critically depends on the erodibility of its fine soils, as the fine soil has higher resistance against erosion. Therefore, for the estimation of the bank erosion in the case of a composite river bank, it is important to determine the critical shear stress and erodibility coefficients of the bank soil and their spatial distribution. In the present study, erodibility parameters of the river bank of Brahmaputra in India have been estimated through 58 in situ submerged jet tests. The significance of spatial and layer‐wise distribution of the erodibility parameters was tested through analysis of variance (ANOVA). Results indicate that the spatial variation of erodibility parameters is highly significant, but layer‐wise variations of the erodibility parameters are not significant. Therefore, the erodibility of the riverbank depends on the particular location, whereas layer‐wise average erodibility parameters can be lumped for the estimation of the bank erosion for the specific site. Using the measured erodibility parameters, yearly river bank erosions at the study locations were computed and found to fall within the reported range of the bank erosion in the Brahmaputra River. Copyright © 2010 John Wiley & Sons, Ltd.     

Relationships between physical‐geochemical soil properties and erodibility of streambanks among different physiographic provinces of Tennessee,USA

Erosion of cohesive soils in fluvial environments is dependent on physical, geochemical and biological properties, which govern inter‐particle attraction forces and control detachment rates from stream beds and banks. Most erosion rate models are based on the excess shear stress equation where the soil erodibility coefficient (k_d) is multiplied by the difference between the boundary hydraulic shear stress (τ_b) and the soil critical shear stress (τ_c). Both k_d and τ_c are a function of soil properties and must be obtained through in situ field or laboratory testing. Many studies have generated predictive relationships for k_d and τ_c derived from various soil properties. These studies typically were conducted in watersheds within a single physiographic region with a common surficial geology and/or investigated a limited number of soil properties, particularly geochemical properties. With widely reported differences in relationships between τ_c and soil properties, this study investigated differences in predictive relationships for τ_c among different physiographic provinces in Tennessee, USA. Erodibility parameters were determined in the field using a mini‐jet test device. Among these provinces, statistically four unique clusters were identified from a dataset of 128 observations and these data clusters were used to develop predictive models for τ_c to identify dominant properties governing erosion. In these clusters, 16 significant physical and geochemical soil properties were identified for τ_c prediction. Among these soil properties, water content and passing #200 sieve (percentage soil less than 75 μm) were the dominant controlling parameters to predict τ_c in addition to clay percentage (< 2 μm), bulk density, and soil pore water chemistry. This study suggests that unique relationships exist for physiographic provinces that are likely due to soil physical‐geochemical processes associated with surficial geology that determine minerology of the cohesive soil. Copyright © 2017 John Wiley & Sons, Ltd.     

Processes and forms of an unstable alluvial system with resistant,cohesive streambeds

As a response to channelization projects undertaken near the turn of the 20th century and in the late 1960s, upstream reaches and tributaries of the Yalobusha River, Mississippi, USA, have been rejuvenated by upstream‐migrating knickpoints. Sediment and woody vegetation delivered to the channels by mass failure of streambanks has been transported downstream to form a large sediment/debris plug where the downstream end of the channelized reach joins an unmodified sinuous reach. Classification within a model of channel evolution and analysis of thalweg elevations and channel slopes indicates that downstream reaches have equilibrated but that upstream reaches are actively degrading. The beds of degrading reaches are characterized by firm, cohesive clays of two formations of Palaeocene age. The erodibility of these clay beds was determined with a jet‐test device and related to critical shear stresses and erosion rates. Repeated surveys indicated that knickpoint migration rates in these clays varied from 0·7 to 12 m a^?1, and that these rates and migration processes are highly dependent upon the bed substrate. Resistant clay beds of the Porters Creek Clay formation have restricted advancement of knickpoints in certain reaches and have caused a shift in channel adjustment processes towards bank failures and channel widening. Channel bank material accounts for at least 85 per cent of the material derived from the channel boundaries of the Yalobusha River system. Strategies to reduce downstream flooding problems while preventing upstream erosion and land loss are being contemplated by action agencies. One such proposal involves removal of the sediment/debris plug. Bank stability analyses that account for pore‐water and confining pressures have been conducted for a range of hydrologic conditions to aid in predicting future channel response. If the sediment/debris plug is removed to improve downstream drainage, care should be taken to provide sufficient time for drainage of groundwater from the channel banks so as not to induce accelerated bank failures. Published in 2002 John Wiley & Sons, Ltd.     

Erodibility study of sediment in a fast-flowing river

Determination of sediment stability in the field is challenging because bed shear stress (BSS), a determining factor of sediment erosion, can’t easily be directly measured. To tackle this challenge and reliably assess sediment erodibility in a fast flowing river, a standalone underwater camera system and a new insitu flume (ISF) were developed and applied in this study. The camera system was used to record sediment movement and the new ISF was used for measuring critical bottom shear stress (CBSS). The camera can be deployed alone in water to record videos or take pictures with light emitting diode (LED) lighting and flexible schedule settings. The ISF is based on the concept that the amount of force needed to erode the same particle under different flow conditions should be similar. Two high resolution Acoustic Doppler Current Profilers (ADCP) also were deployed in the field to collect velocity-depth profiles which are used by conventional methods to calculate BSS with the law of the wall. The sediment erodibility was then assessed based on the comparison between the obtained CBSS and BSS and then further verified with the recorded observations from the deployed camera. The results reveal that the widely used conventional method can produce large uncertainties and is not adequate to provide meaningful conclusion under these conditions.     

Determination of critical shear stress of non‐cohesive soils using submerged jet test and turbulent kinetic energy

Laboratory tests using Jet Erosion Testing (JET) apparatus, impinging normally on a horizontal boundary, were conducted to determine the critical shear stress (τ_c) of non‐cohesive soil samples. A three‐dimensional (3D) SonTek/YSI 16 MHz Micro‐Acoustic Doppler Velocimeter (MicroADV) was used to measure turbulent kinetic energy (TKE) at a radial limit of entrainment in the wall jet zone and the measurements were used to calculate τ_c of the samples. The results showed that TKE increases exponentially with increasing particle size. The τ_c from this study were comparable (R² = 0.8) to the theoretical τ_c from Shields diagram after bed roughness scale ratio (D/k_s), due to the non‐uniform bed conditions, was accounted for. This study demonstrated that JET and TKE can be used to determine τ_c of non‐cohesive soils. The use of JET and TKE was found to be faster and easier when compared to the conventional approach of using flumes. A relationship of TKE at the onset of incipient motion (TKE_c) and samples’ D₅₀ developed in this study can be used to predict τ_c of non‐cohesive soils under similar non‐uniform conditions. Copyright © 2015 John Wiley & Sons, Ltd.     

Erodibility of low‐compaction steep‐sloped reclaimed surface mine lands in the southern Appalachian region,USA

The use of loose spoils on steep slopes for surface coal mining reclamation sites has been promoted by the US Department of Interior, Office of Surface Mining for the establishment of native forest, as prescribed by the Forest Reclamation Approach (FRA). Although low‐compaction spoils improve tree survival and growth, erodibility on steep slopes was suspected to increase. This study quantified a combined K_C factor (combining the effects of the soil erodibility K factor and cover management C) for low compaction, steep‐sloped (>20°) reclaimed mine lands in the Appalachian region, USA. The combined K_C factor was used because standard Unit Plot conditions required to separate these factors, per Revised Universal Soil Loss Equation (RUSLE) experimental protocols, were not followed explicitly. Three active coal mining sites in the Appalachian region of East Tennessee, each containing four replicate field plots, were monitored for rainfall and sediment yields during a 14‐month period beginning June 2009. Average cumulative erosivity for the study sites during the monitoring period was measured as 5248.9 MJ·mm·ha^?1·h^?1. The K_C ranged between 0.001 and 0.05 t·ha·h·ha^?1·MJ^?1·mm^?1, with the highest values occurring immediately following reclamation site construction as rills developed (June – August 2009). The K_C for two study sites with about an 18–20 mm spoil D₈₄ were above 0.01 t·ha·h·ha^?1·MJ^?1·mm^?1 during rill development, and below 0.003 t·ha·h·ha^?1·MJ^?1·mm^?1 after August 2009 for the post‐rill development period. The K_C values for one site with a 40 mm spoil D₈₄ were never above 0.008 t·ha·h·ha^?1·MJ^?1·mm^?1 and also on average were lower, being more similar to the other two sites after the rill development period. Based on an initial K_C factor (K_e) measured during the first few storm events, the average C factor (C_e) was estimated as 0.58 for the rill development period and 0.13 for the post‐rill development period. It appears that larger size fractions of spoils influence K_C and C_e factors on low‐compaction steep slopes reclamation sites. Copyright © 2013 John Wiley & Sons, Ltd.     

Variation in the vertical zonality of erodibility and critical shear stress of rill erosion in China's Hengduan Mountains

Soil erodibility is an essential parameter used in soil erosion prediction. This study selected the Liangshan town watershed to quantify variation in the vertical zonality of rill erodibility (k_r) in China's ecologically fragile Hengduan Mountains. Soil types comprised of yellow–brown (soil A), purple (soil B), and dry-red (soil C) in a descending order of occurrence from the summit to the valley, which roughly corresponds to the vertical climate zone (i.e. cool-high mountain, warm-low mountain, and dry-hot valley sections) of the study area. With elevation, vertical soil zonality varied in both soil organic matter (SOM) content and soil particle-size fractions. A series of rill erosion-based scour experiments were conducted, using water discharge rates of 100, 200, 300, 400, 500, and 600 mL min^-1. Additionally, detachment rates (Dr) were measured under three hydrological conditions (the drainage, saturation, and seepage treatments). Results show that both Dr and flow shear stress (Ʈ) values increased as discharge increased. As elevation increased, the k_r values decreased, while the vertical zonality of critical shear stress (Ʈ_c) values showed no obvious variation. The highest k_r values were observed during the seepage treatment, followed by the saturation treatment then drainage treatment, indicating that variation in vertical hydraulic gradients could significantly alter k_r values. This study also found that land-use types could also alter k_r and Ʈ_c values. Further research, however, is necessary to better quantify the effects of subsurface hydrological conditions and land-use types on k_r under different soil zonalities in China's Hengduan Mountains. © 2018 John Wiley & Sons, Ltd.     

Effects of biological soil crusts on soil detachment process by overland flow in the Loess Plateau of China

Biological soil crusts (BSCs) cover up to 60 to 70% of the soil surface in grasslands after the ‘Grain for Green’ project was implemented in 1999 to rehabilitate the Loess Plateau. However, few studies exist that quantify the effects of BSCs on the soil detachment process by overland flow in the Loess Plateau. This study investigated the potential effects of BSCs on the soil detachment capacity (D_c), and soil resistance to flowing water erosion reflected by rill erodibility and critical shear stress. Two dominant BSC types that developed in the Loess Plateau (the later successional moss and the early successional cyanobacteria mixed with moss) were tested against natural soil samples collected from two abandoned farmland areas. The samples were subjected to flow scouring under six different shear stresses ranging from 7.15 to 24.08 Pa. The results showed that D_c decreased significantly with crust coverage under both moss and mixed crusts. The mean D_c of bare soil (0.823 kg m^?2 s^?1) was 2.9 to 48.4 times greater than those of moss covered soil (0.017–0.284 kg m^?2 s^?1), while it (3.142 kg m^?2 s^?1) was 4.9 to 149.6 times greater than those of mixed covered soil (0.021–0.641 kg m^?2 s^?1). The relative detachment rate of BSCs compared with bare soils decreased exponentially with increasing BSC coverage for both types of BSCs. The D_c value can be simulated by flow shear stress, cohesion, and BSC coverage using a power function (NSE ≥ 0.59). Rill erodibility also decreased with coverage of both crust types. Rill erodibility of bare soil was 3 to 74 times greater than those of moss covered soil and was 2 to 165 times greater than those of mixed covered soil. Rill erodibility could also be estimated by BSC coverage in the Loess Plateau (NSE ≥ 0.91). The effect of crust coverage on critical shear stress was not significant. Copyright © 2015 John Wiley & Sons, Ltd.     

Site‐scale variability of streambank fluvial erodibility parameters as measured with a jet erosion test

The erosion rate of cohesive streambanks is typically modelled using the excess shear stress equation, dependent on two erodibility parameters: critical shear stress and erodibility coefficient. The jet erosion test (JET) has become the most common method for estimating these erodibility parameters in situ. Typically, results from a few JETs are averaged to acquire a single set of parameters for characterizing a streambank layer; however, this may be inadequate for accurately characterizing erodibility. The research objectives were to investigate the variability of JET results from assumed homogeneous streambank layers and to estimate the number of JETs required to accurately characterize erodibility for use in predictive models. On three unique streambanks in Oklahoma and across a range of erodibility, 20 to 30 JETs were conducted over a span of three days at each site. Unique to this research, each JET was analysed using the Blaisdell, scour depth and iterative solutions. The required sample size to accurately estimate the erodibility parameters depended on the JET solution technique, the parameter being estimated, and the degrees of precision and confidence. Conducting three to five JETs per soil layer on a streambank typically provided an order of magnitude estimate of the erodibility parameters. Because the parameters were log‐normally distributed, using empirical equations to predict erosion properties based on soil characteristics will likely contain high uncertainty and thus should be used with caution. This study exemplifies the need to conduct in situ measurements using the JET to accurately characterize streambank resistance to fluvial erosion. Copyright © 2015 John Wiley & Sons, Ltd.     

An alternative method for interpreting JET erosion test (JET) data: Part 2. Application

This paper reports the results of jet tester experiments on soil samples of uniform properties which allow quantitative application of the new theory proposed in part 1 of these publications. This theory explores the possibly that a more adequate indicator of soil erodibility may be obtained by using the mass (and so volume) of soil eroded by the jet and the depth of scour penetration, rather than by using penetration depth alone, as assumed in the commonly‐used data interpretation method. It is shown that scour geometry can be well described using a generalized form of the Gaussian function, defined by its standard deviation and maximum depth. Using a published expression for jet kinetic energy flux, the new theory divides this flux into that used to erode soil, and the remainder which is dissipated in a variety of ways. Jet experiments on a specially‐prepared uniform soil sample are reported which provide the key to determining the spatial variability in the profile resistance to erosion offered by field soils. This resistance is expressed in the work required to erode unit mass of soil, denoted as J (in J/kg). The paper also gives results obtained on the profile variation in J for jet tests carried out at riverine sites on the upper Brisbane River, Queensland, Australia. As expected in most natural soil profiles, the results show an increase in J with depth in the profile. The soil resistance (J) is compared to the traditional interpretation of soil erodibility, (k_d). The graphical comparison of these two indicators illustrates the inverse type of relationship between them which is expected from their respective definitions, but this relationship is associated with significant scatter. Possible reasons for this scatter are given, together with comments on jet tester experience in a wide variety of soil types. Copyright © 2017 John Wiley & Sons, Ltd.     

Quantifying the effects of plant litter in the topsoil on the soil detachment process by overland flow in typical grasslands of the Loess Plateau,China

Plant litter can be incorporated into topsoil by a natural process, affecting the soil erosion process. This is a widespread phenomenon in erosion-prone areas. This study was conducted to investigate the effect of litter incorporation on the process of soil detachment on the Loess Plateau, China. Four common plant litters (Bothriochloa ischaemum L. Keng., Artemisia sacrorum Ledeb., Setaria viridis L. Beauv., and Artemisia capillaris Thunb.) were collected, then incorporated into the silt loam soil at five rates (0.1, 0.4, 0.7, 1.0, and 1.3 kg m⁻²) on the basis of our field investigation. Twenty litter–soil treatments and one bare soil control were prepared. After 50 days of natural stabilization, 30 soil samples of each treatment were collected. We used a flume test to scour the soil samples under six flow shear stress conditions (5.66, 8.31, 12.21, 15.55, 19.15, and 22.11 Pa). The results showed that the different incorporated litter masses and morphological characteristics, such as litter tissue density (ranging from 0.52 to 0.68 g cm⁻³), length density (2.34 to 91.00 km m⁻³), surface area density (LSAD; 27.9 to 674.2 m² m⁻³), and volume ratio (0.003 to 0.050 m³ m⁻³), caused varied soil detachment capacities (0.043 to 4.580 kg·m⁻²·s⁻¹), rill erodibilities (0.051 to 0.237 s m⁻¹), and critical shear stresses (2.02 to 6.83 Pa). The plant litter incorporated within the soil reduced the soil detachment capacities by 38%–59%, lowered the rill erodibilities by 32%–46%, and increased the critical shear stresses by 98%–193% compared with the bare soil control. The soil containing B. ischaemum (L.) Keng. litter was more resistant to erosion. By comparing different parameters, we found that the contact area between the litter and soil was the main factor affecting the soil detachment process. The soil erosion resistance increased with the increasing contact area between the soil and litter. Furthermore, the litter incorporation effect on rill erodibility can be comprehensively reflected by LSAD (R² = .93; Nash–Sutcliffe efficiency = 0.79), which could be used to adjust the rill erodibility parameter in physical process-based soil erosion models.     

黏性土的动剪切模量比和阻尼比与剪应变关系的统计分析

动剪切模量比和阻尼比是土体重要的动力特性参数,这两种参数取值的合理性对场地地震响应分析的结果有重要影响.为进一步完善黏性土的动剪切模量比和阻尼比随剪应变的变化关系的研究,给出了新的计算模型和推荐曲线.新曲线的计算模型基于Davidenkov模型和新的阻尼比计算模型,通过对搜集的大量黏性土数据进行非线性回归分析后得到.将分析结果与已有国内外学者的成果进行对比,验证了新计算模型具有较好的可靠性和工程实用性.     

A comparison of tectonic ambient shear stress value in China with that in western USA

Introduction The stress status of the earths crust is closely related to global structure, the direction of plate movement, the drive mechanism of plate, earthquake cause, etc. Therefore the researches of the stress status of the earths crust and the process of dynamic evolution are paid a great attention to by many people around the world (Zoback, Zoback, 1980; Zoback, et al, 1989; Zoback, 1989; Spence, 1997; Fuchs, 1997; Plenefish, Bonjer, 1997; Muller, et al, 1997; XU, et al, 1989; WAN…     

Assessment of erosion and settling properties of fine sediments stored in cobble bed rivers: the Arc and Isère alpine rivers before and after reservoir flushing

Cohesive sediment dynamics in mountainous rivers is poorly understood even though these rivers are the main providers of fine particles to the oceans. Complex interactions exist between the coarse matrix of cobble bed rivers and fine sediments. Given that fine sediment load in such environments can be very high due to intense natural rainfall or snowmelt events and to man‐induced reservoir or dam flushing, a better understanding of the deposition and sedimentation processes is needed in order to reduce ecohydrological downstream impacts. We tested a field‐based approach on the Arc and Isère alpine rivers combining measurements of erosion and settling properties of river bed deposits before and after a dam flushing, with the U‐GEMS (Gust Erosion Microcosm System) and SCAF (System Characterizing Aggregates and Flocs), respectively. These measurements highlight that critical shears, rates of erosion, settling velocities and propensity of particles to flocculate are highly variable in time and space. This is reflective of the heterogeneity of the hydrodynamic conditions during particle settling, local bed roughness, and nature and size of particles. Generally the deposits were found to be stable relative to what is measured in lowland rivers. It was, however, not possible to make a conclusive assessment of the extent to which the dynamics of deposits after reservoir flushing were different from those settled after natural events. The absence of any relationships between erosion and deposition variables, making it impossible to predict one from another, underlined the need to measure all of them to have a full assessment of the fine sediment dynamics and to obtain representative input variables for numerical models. While the SCAF was found to be effective, an alternative to the U‐GEMS device will have to be found for the erodibility assessment in cobble bed rivers, in order to make more rapid measurements at higher shears. Copyright © 2017 John Wiley & Sons, Ltd.     

Bank‐toe processes in incised channels: the role of apparent cohesion in the entrainment of failed bank materials

Numerous processes may instigate bank retreat and the consequent collection of failed cohesive materials at the bank toe. Cohesion between the failed material and the substrate can provide additional strength to resist direct fluvial entrainment. Failed, cohesive material can act as a form of natural bank‐toe protection by consuming and diverting flow energy that may otherwise be used to further scour the basal zone of incising channels. Investigations in Goodwin Creek, Mississippi, have revealed the existence of apparent cohesion between failed, cohesive blocks and their underlying surface. The method used to assess this cohesion involved a pulley system mounted on a tripod and supporting a load cell. Mean and maximum apparent‐cohesion values of 1·08 kPa and 2·65 kPa, respectively, were measured in this way, identifying a source that bonds blocks to the underlying surface. Cohesion values and types vary spatially and temporally. Tensiometric tests beneath blocks suggest that cohesion resulting from matric suction alone may be as much as 3·5 kPa in summer and 1·8 kPa in winter. Apparent cohesion is believed to have been sufficient to help prevent removal of the largest blocks by a peak flow of 66·4m³&sol;s on 23 September 1997. Maximum excess shear stress required to entrain a D₇₅ block can be augmented by as much as 97% by the presence of apparent cohesion at the block–substrate interface when compared with a condition with zero apparent cohesion at the block underside. Given these findings, it is no longer sufficient to estimate block entrainment in the basal area from block size or bed roughness alone, as in a Shields‐type approach. Copyright © 2001 John Wiley & Sons, Ltd.     

Laboratory and theoretical evaluation of impact of packing density,particle shape,and uniformity coefficient on erodibility of coarse-grained soil particles

Sedimentation – including erosion, transport, and deposition of coarse-grained particles – is a primary and growing environmental, engineering, and agricultural issue around the world. Soil erosion occurs when the hydrodynamic force induced by flowing water exceeds the geotechnical resistance of soils, as measured by critical shear stress for initiation of soil-particle motion. Even though various quantitative methods have been suggested with respect to different types of soil, the most widely accepted formula to estimate critical shear stress for coarse-grained soil is a direct function of the median grain size of the soil particles; however, the erosion resistance of soils also varies with other geotechnical properties, such as packing density, particle shape, and uniformity coefficient. Thus, in this study, a combined rolling–lift model for particle detachment was derived based on theoretical analysis. A series of experimental flume tests were conducted with specimens prepared with standard soil types, as well as laboratory-prepared mixtures of coarse-grained soil to validate the theoretical model and determine the effect of other geotechnical properties on the erosion characteristics of coarse grains, coupled with the effect of median particle size. The results indicated that the median grain size is the primary variable determining the resistance of coarse grains, but the critical shear stress also varies with the packing density of the soil matrix. In addition, angular particles show more erosion resistance than rounded particles, and the erosion potential of a soil decreased when the grain is well graded (higher value of uniformity coefficient). Additionally, regression analysis was performed to quantify the effect of each parameter on the critical shear stress of coarse grains. © 2020 John Wiley & Sons, Ltd.     

Assessment of soil factors controlling ephemeral gully erosion on agricultural fields

The soil factor is crucial in controlling and properly modeling the initiation and development of ephemeral gullies (EGs). Usually, EG initiation has been related to various soil properties (i.e. sealing, critical shear stress, moisture, texture, etc.); meanwhile, the total growth of each EG (erosion rate) has been linked with proper soil erodibility. But, despite the studies to determine the influence of soil erodibility on (ephemeral) gully erosion, a universal approach is still lacking. This is due to the complex relationship and interactions between soil properties and the erosive process. A feasible soil characterization of EG erosion prediction on a large scale should be based on simple, quick and inexpensive tests to perform. The objective of this study was to identify and assess the soil properties – easily and quickly to determine – which best reflect soil erodibility on EG erosion. Forty‐nine different physical–chemical soil properties that may participate in establishing soil erodibility were determined on agricultural soils affected by the formation of EGs in Spain and Italy. Experiments were conducted in the laboratory and in the field (in the vicinity of the erosion paths). Because of its importance in controlling EG erosion, five variables related to antecedent moisture prior to the event that generated the gullies and two properties related to landscape topography were obtained for each situation. The most relevant variables were detected using multivariate analysis. The results defined 13 key variables: water content before the initiation of EGs, organic matter content, cation exchange capacity, relative sealing index, two granulometric and organic matter indices, seal permeability, aggregates stability (three index), crust penetration resistance, shear strength and an erodibility index obtained from the Jet Test erosion apparatus. The latter is proposed as a useful technique to evaluate and predict soil loss caused by EG erosion. Copyright © 2018 John Wiley & Sons, Ltd.     

Plot‐scale measurement of soil erosion at the experimental area of Sparacia (southern Italy)

Obtaining good quality soil loss data from plots requires knowledge of the factors that affect natural and measurement data variability and of the erosion processes that occur on plots of different sizes. Data variability was investigated in southern Italy by collecting runoff and soil loss from four universal soil‐loss equation (USLE) plots of 176 m², 20 ‘large’ microplots (0·16 m²) and 40 ‘small’ microplots (0·04 m²). For the four most erosive events (event erosivity index, R_e ≥ 139 MJ mm ha^?1 h^?1), mean soil loss from the USLE plots was significantly correlated with R_e. Variability of soil loss measurements from microplots was five to ten times greater than that of runoff measurements. Doubling the linear size of the microplots reduced mean runoff and soil loss measurements by a factor of 2·6–2·8 and increased data variability. Using sieved soil instead of natural soil increased runoff and soil loss by a factor of 1·3–1·5. Interrill erosion was a minor part (0·1–7·1%) of rill plus interrill erosion. The developed analysis showed that the USLE scheme was usable to predict mean soil loss at plot scale in Mediterranean areas. A microplot of 0·04 m² could be used in practice to obtain field measurements of interrill soil erodibility in areas having steep slopes. Copyright © 2003 John Wiley & Sons, Ltd.     

Future fluvial erosion and sedimentation potential of cohesive sediments in a coastal river reach of SW Finland

This study aims to analyse the combined impacts of future discharges and sea levels on erosion–sedimentation potential, and its seasonal changes, in a ~43‐km‐long coastal river reach of South‐west Finland. To our knowledge, this kind of combined study has not been performed before. In addition to surveying the present erosion–sedimentation conditions, the daily erosion–sedimentation potential is simulated with a one‐dimensional hydrodynamic model for the 1971–2000 and 2070–2099 periods by applying four discharge scenarios. Different sea level stages are also employed in the simulations. All scenarios forecast increasing autumn and winter discharges, but diminishing summer discharges. This indicates increasing river channel erosion, particularly during winters and autumns. Although discharge changes have altogether a greater influence on erosion–sedimentation potential, the importance of sea level changes on sedimentation is noticeable in the estuary. The rising sea level scenarios increase the sedimentation potential. In total, by 2070–2099, the erosion potential may increase in most parts of the study area. Copyright © 2013 John Wiley & Sons, Ltd.