Reduced forms of sulfur in the brine of Saline–Soda Lake Doroninskoe,eastern Transbaikal Region

Contents of inorganic reduced forms of sulfur were determined in the oxygen-bearing waters of saline-soda Lake Doroninskoe. The vertical and annual distributions of individual species and total reduced sulfur have been studied. It was found that oxic zone ubiquitously contains reduced sulfur with contents: HS⁻ 0.002–3.86 mg/l, S⁰ 0.002–0.129 mg/l, S^{0; 4+} 0.014–9.19 mg/l. Oxygen concentrations varied from 0 to 6.8 mg/l. These sulfur compounds show unsystematic vertical distribution, which during transitional season is controlled by intensity of bacterial processes.     

Reduced sulfur species in a stratified seawater lake (Rogoznica Lake, Croatia); seasonal variations and argument for organic carriers of reactive sulfur

Over a period of a year, Hg⁰-reactive, total reduced sulfur species (RSS_T), as well as a non-volatile fraction that cannot be gas-stripped at pH ∼2 (RSS_NV), have been measured by voltammetry in a stratified, saline lake. In the hypolimnion, RSS_T is dominated by unusually high (up to 5 mM) dissolved divalent sulfur (S^−II), present as H₂S + HS⁻ and as inorganic polysulfides (H_xS_n^x−2). Less abundant RSS_NV is attributed to dissolved zero-valent sulfur (S⁰) in inorganic polysulfides. Assuming negligible contribution of organic S⁰ species in the hypolimnion, the equilibrium distribution of polysulfide ions is calculated; S₅²⁻ is found to predominate. In the epilimnion, all RSS_T consists of RSS_NV within analytical uncertainty. Through spring and summer, RSS_T and RSS_NV display little vertical or seasonal variation, but they increase dramatically when stratification breaks down in autumn. Based on decay rate, RSS during mixing events is attributed to dissolved S₈ from oxidation of sulfide and decomposition of inorganic polysulfides. This hypothesis quantitatively predicts precipitation of elemental sulfur in a year when colloidal sulfur was observed and predicts no precipitation in a year when it was not observed. Except during mixing events, the entire water column is undersaturated with respect to both rhombic sulfur and biologic sulfur, and the limited variations of RSS exclude hydrophobic and volatile aqueous S₈ as a major species. During such periods, RSS (typically 8 nM) may be associated with organic carbon, perhaps as adsorbed S₈ or as covalently bound polysulfanes or polysulfides. The hypolimnion is viewed as a zero-valent sulfur reactor that creates S⁰-containing, dissolved organic macromolecules during stable stratification periods. Some are sufficiently degradation-resistant and hydrophilic to be dispersed throughout the lake during mixing events, subsequently giving rise to ∼10⁻⁸ M RSS in the oxic water column. Voltammetrically determined RSS in oxic natural waters has often been described as “sulfide” or “metal complexed sulfide”, implying an oxidation state of S^−II; we argue that RSS in oxic Rogoznica Lake waters is mainly S⁰.     

Reduced sulfur and iron species in anoxic water column of meromictic crater Lake Pavin (Massif Central, France)

The vertical distribution of reduced sulfur species (RSS including H₂S/HS⁻, S⁰, electroactive FeS) and dissolved Fe(II) was studied in the anoxic water column of meromictic Lake Pavin. Sulfide concentrations were determined by two different analytical techniques, i.e. spectophotometry (methylene blue technique) and voltammetry (HMDE electrode). Total sulfide concentrations determined with methylene blue method (∑H₂S_MBRS) were in the range from 0.6 µM to 16.7 µM and were substantially higher than total reduced sulfur species (RSS_V) concentrations determined by voltammetry, which ranged from 0.1 to 5.6 μM. The observed difference in the sulfide concentrations between the two methods can be assigned to the presence of FeS colloidal species.Dissolved Fe was high (> 1000 µM), whereas dissolved Mn was only 25 µM, in the anoxic water column. This indicates that Fe is the dominant metal involved in sulfur redox cycling and precipitation. Consequently, in the anoxic deep layer of Lake Pavin, “free” sulfide, H₂S/HS⁻, was low; and about 80% of total sulfide detected was in the electroactive FeS colloidal form. IAP calculations showed that the Lake Pavin water column is saturated with respect to FeS_am phase. The upper part of monimolimnion layer is characterized by higher concentrations of S(0) (up to 3.4 µM) in comparison to the bottom of the lake. This behavior is probably influenced by sulfide oxidation with Fe(III) oxyhydroxide species.     

Fractionation of multiple sulfur isotopes during phototrophic oxidation of sulfide and elemental sulfur by a green sulfur bacterium

We present multiple sulfur isotope measurements of sulfur compounds associated with the oxidation of H₂S and S⁰ by the anoxygenic phototrophic S-oxidizing bacterium Chlorobium tepidum. Discrimination between ³⁴S and ³²S was +1.8 ± 0.5‰ during the oxidation of H₂S to S⁰, and −1.9 ± 0.8‰ during the oxidation of S⁰ to , consistent with previous studies. The accompanying Δ³³S and Δ³⁶S values of sulfide, elemental sulfur, and sulfate formed during these experiments were very small, less than 0.1‰ for Δ³³S and 0.9‰ for Δ³⁶S, supporting mass conservation principles. Examination of these isotope effects within a framework of the metabolic pathways for S oxidation suggests that the observed effects are due to the flow of sulfur through the metabolisms, rather than abiotic equilibrium isotope exchange alone, as previously suggested. The metabolic network comparison also indicates that these metabolisms work to express some isotope effects (between sulfide, polysulfides, and elemental sulfur in the periplasm) and suppress others (kinetic isotope effects related to pathways for oxidation of sulfide to sulfate via the same enzymes involved in sulfate reduction acting in reverse). Additionally, utilizing fractionation factors for phototrophic S oxidation calculated from our experiments and for other oxidation processes calculated from the literature (chemotrophic and inorganic S oxidation), we constructed a set of ecosystem-scale sulfur isotope box models to examine the isotopic consequences of including sulfide oxidation pathways in a model system. These models demonstrate how the small δ³⁴S effects associated with S oxidation combined with large δ³⁴S effects associated with sulfate reduction (by SRP) and sulfur disproportionation (by SDP) can produce large (and measurable) effects in the Δ³³S of sulfur reservoirs. Specifically, redistribution of material along the pathways for sulfide oxidation diminishes the net isotope effect of SRP and SDP, and can mask the isotopic signal for sulfur disproportionation if significant recycling of S intermediates occurs. We show that the different sulfide oxidation processes produce different isotopic fields for identical proportions of oxidation, and discuss the ecological implications of these results to interpreting minor S isotope patterns in modern systems and in the geologic record.     

Sulfur biogeochemistry and isotopic fractionation in shallow groundwater and sediments of Owens Dry Lake, California

Groundwater and sediment samples (∼ 1 m depth) at sites representative of different groundwater pathways were collected to determine the aqueous speciation of sulfur and the fractionation of sulfur isotopes in aqueous and solid phases. In addition, selected sediment samples at 5 depths (from oxic to anoxic layers) were collected to investigate the processes controlling sulfur biogeochemistry in sedimentary layers. Pyrite was the dominant sulfur-bearing phase in the capillary fringe and groundwater zones where anoxic conditions are found. Low concentrations of pyrite (< 5.9 g kg^− 1) coupled with high concentrations of dissolved sulfide (4.81 to 134.7 mg L^− 1) and low concentrations of dissolved Fe (generally < 1 mg L^− 1) and reducible solid-phase Fe indicate that availability of reactive Fe limits pyrite formation. The relative uniformity of down-core isotopic trends for sulfur-bearing mineral phases in the sedimentary layers suggests that sulfate reduction does not result in significant sulfate depletion in the sediment. Sulfate availability in the deeper sediments may be enhanced by convective vertical mixing between upper and lower sedimentary layers due to evaporative concentration. The large isotope fractionation between dissolved sulfate and sedimentary sulfides at Owens Lake provides evidence for initial fractionation from bacterial sulfate reduction and additional fractionation generated by sulfide oxidation followed by disproportionation of intermediate oxidation state sulfur compounds. The high salinity in the Owens Lake brines may be a factor controlling sulfate reduction and disproportionation in hypersaline conditions and results in relatively constant values for isotope fractionation between dissolved sulfate and total reduced sulfur.     

电感耦合等离子体发射光谱法测定地热水中的硫化物

地热水中的硫化物(H_2S、HS~-和S~(2-))通常受到硫酸根、亚硫酸根、硫代硫酸根等硫元素的共存干扰,并且硫化物具有热、光、氧不稳定性,在水样保存、前处理、标准溶液配制等环节影响着测试的准确度和精密度。本文在现场采集的地热水水样中加入乙酸锌及氢氧化钠,使硫化物形成硫化锌沉淀而与溶液分离,将此沉淀溶于双氧水和逆王水,使低价态的S2-氧化成稳定的SO_4~(2-),选择易于纯化且性质稳定的硫酸钠配制硫标准储备液,以182.624 nm谱线作为硫元素分析谱线,应用电感耦合等离子体发射光谱法测定出地热水样中的硫化物含量。硫的浓度在0.1~100 mg/L范围内与其发射强度呈线性(相关系数为0.9994);方法检出限为0.009 mg/L,相对标准偏差(n=11)低于1.80%,实际水样中硫化物的加标回收率介于99.0%~103.0%。与前人相关测试方法相比,本方法的技术指标具有优势。     

Biogeochemistry of sulfur and iron in Thioploca-colonized surface sediments in the upwelling area off central chile

The biogeochemistry of sedimentary sulfur was investigated on the continental shelf off central Chile at water depths between 24 and 88 m under partial influence of an oxygen minimum zone. Dissolved and solid iron and sulfur species, including the sulfur intermediates sulfite, thiosulfate, and elemental sulfur, were analyzed at high resolution in the top 20 cm. All stations were characterized by high rates of sulfate reduction, but only the sediments within the Bay of Concepción contained dissolved sulfide. Due to advection and/or in-situ reoxidation of sulfide, dissolved sulfate was close to bottom water values. Whereas the concentrations of sulfite and thiosulfate were mostly in the submicromolar range, elemental sulfur was by far the dominant sulfur intermediate. Although the large nitrate- and sulfur-storing bacteria Thioploca were abundant, the major part of S⁰ was located extracellularly. The distribution of sulfur species and dissolved iron suggests the reaction of sulfide with FeOOH as an important pathway for sulfide oxidation and sulfur intermediate formation. This is in agreement with the sulfur isotope composition of co-existing elemental sulfur and iron monosulfides. In the Bay of Concepción, sulfur isotope data suggest that pyrite formation proceeds via the reaction of FeS with polysulfides or H₂S. At the shelf stations, on the other hand, pyrite was significantly depleted in ³⁴S relative to its potential precursors FeS and S⁰. Isotope mass balance considerations suggest further that pyritization at depth includes light sulfide, potentially originating from bacterial sulfur disproportionation. The δ³⁴S-values of pyrite down to −38‰ vs. V-CDT are among the lightest found in organic-rich marine sediments. Seasonal variations in the sulfur isotope composition of dissolved sulfate indicated a dynamic non-steady-state sulfur cycle in the surface sediments. The ¹⁸O content of porewater sulfate increased with depth at all sites compared to the bottom water composition due to intracellular isotope exchange reactions during microbial sulfur transformations.     

Annual fluctuations in sulfur isotope fractionation in the water column of a euxinic marine basin

The sulfur cycle of Mariager Fjord was studied by following the pool of sulfide in the anoxic water and its isotopic composition during a period of 3 yr. Though most of the sulfide accumulating in the fjord was formed in the sediment, the isotopic composition of sulfide in the water was different from the isotopic composition of sulfide diffusing into the water from the sediment. The mean isotopic composition of the water column sulfide (δ³⁴S) varied during the year between −13‰ and −21‰ with the most negative values reached during winter/early spring, while the sulfide diffusing into the water from the sediment had a mean isotope composition of −11.3‰. This annual pattern suggested that processes in the oxidative part of the sulfur cycle were responsible for the excess fractionation, and mass-balance considerations indicated that the excess fractionation of the sulfur isotopes could be accounted for by disproportionation of S⁰ or S₂O₃²⁻ in the water column, but not by water column sulfate reduction or sulfide oxidation alone. MPN counts demonstrated that a population of more than 3 × 10⁴ cells mL⁻¹ capable of growing by disproportionation of these two substrates was present in all depths of the fjord. The results presented in this communication demonstrate that the isotopic depletion of sulfide in anoxic systems may vary between periods of net sulfate reduction versus periods of net sulfide oxidation and indicate that disproportionation of sulfur compounds may be an important step in the sulfur cycle of euxinic basins.     

Simultaneous determination of sulfide, polysulfides and thiosulfate as an aid to ore exploration

The interaction of water and sulfide minerals yields dissolved species which can be utilized to trace back the presence of sulfide minerals and associated minerals. Computer modeling and laboratory and field results show that the most characteristic dissolved species are hydrogen sulfide (H₂S, HS⁻), polysulfide ions (S_n²⁻) and thiosulfate (S₂O₃²⁻), derived from the hydrolysis of sulfide minerals. Typical concentration ranges are: 10⁻⁵ – 10⁻⁷ mole/l for hydrogen sulfide, 10⁻⁶ – 10⁻⁹ mole/l for polysulfides and 10⁻⁵ – 10⁻⁸ mole/l for thiosulfate. The chemical reactivity of these species at contact with air makes them difficult to assess unless determined immediately after sampling.These sulfur species can be determined rapidly and accurately in field conditions by simultaneous titration with mercuric chloride employing an Ag/Ag₂S electrode for the determination of the end points.The application to ore exploration is exemplified by the results of the research on roll-type uranium deposits in the southwest of France.     

Bacteriogenic sulfur isotopic ratios in geology

Stable sulfur isotopes may aid in distinguishing sulfides of a magmatic hydrothermal origin from sulfides containing biogenic sulfur. For those sulfide ore depositis that are intimately associated with the intrusive body from which it is inferred their ore solutions were derived, the variation in S³⁴ values is generally less than ± 5 permil. Biogenic sulfides, on the other hand, exhibit a broad spread in S³⁴ values that is rately less than a few permil. The reason for this is that the sulfur produced, as hydrogen sulfide by anaerobic bacteria, is isotopically fractionated by variable amounts resulting in a relatively broad spread in S³⁴ values.Raw culture experiments have illustrated the isotopic effects resulting from reduction of sulfate to hydrogen sulfate by sulfate reducing bacteria. The characteristics of enrichment of S³² to a highly variable extent in hydrogen sulfide is verified by these experiments.In addition, a series of closed system raw culture experiments resulted in fractionation factors between 1.043 to 1.062 which are similar to variations in S³⁴ between juxtaposed sulfides in nature produced by bacteriogenic processes.Speech delivered on October 1, 1965, on the occasion of the colloquy concerning Sulphurisotopes organized by the Deutsche Forschungsgemeinschaft at Bad Sooden-Allendorf.     

Stable sulfur isotopes in the water column of the Cariaco Basin

Previous geochemical and microbiological studies in the Cariaco Basin indicate intense elemental cycling and a dynamic microbial loop near the oxic-anoxic interface. We obtained detailed distributions of sulfur isotopes of total dissolved sulfide and sulfate as part of the on-going CARIACO time series project to explore the critical pathways at the level of individual sulfur species. Isotopic patterns of sulfate (δ³⁴S_SO4) and sulfide (δ³⁴S_H2S) were similar to trends observed in the Black Sea water column: δ³⁴S_H2S and δ³⁴S_SO4 were constant in the deep anoxic water (varying within 0.6‰ for sulfide and 0.3‰ for sulfate), with sulfide roughly 54‰ depleted in ³⁴S relative to sulfate. Near the oxic-anoxic interface, however, the δ³⁴S_H2S value was ∼3‰ heavier than that in the deep water, which may reflect sulfide oxidation and/or a change in fractionation during in situ sulfide production through sulfate reduction (SR). δ³⁴S_H2S and Δ³³S_H2S data near the oxic-anoxic interface did not provide unequivocal evidence to support the important role of sulfur-intermediate disproportionation suggested by previous studies. Repeated observation of minimum δ³⁴S_SO4 values near the interface suggests ‘readdition’ of ³⁴S-depleted sulfate during sulfide oxidation. A slight increase in δ³⁴S_SO4 values with depth extended over the water column may indicate a reservoir effect associated with removal of ³⁴S-depleted sulfur during sulfide production through SR. Our δ³⁴S_H2S and Δ³³S_H2S data also do not show a clear role for sulfur-intermediate disproportionation in the deep anoxic water column. We interpret the large difference in δ³⁴S between sulfate and sulfide as reflecting fractionations during SR in the Cariaco deep waters that are larger than those generally observed in culturing studies.     

Chemistry and isotope ratios of sulfur in basalts and volcanic gases at Kilauea volcano,Hawaii

Eighteen basalts and some volcanic gases from the submarine and subaerial parts of Kilauea volcano were analyzed for the concentration and isotope ratios of sulfur. By means of a newly developed technique, sulfide and sulfate sulfur in the basalts were separately but simultaneously determined. The submarine basalt has 700 ± 100 ppm total sulfur with δ³⁴S_Σs of $\text{0.7 ± 0.1 ‰}$. The sulfate/sulfide molar ratio ranges from 0.15 to 0.56 and the fractionation factor between sulfate and sulfide is $\text{+7.5 ± 1.5‰}$. On the other hand, the concentration and δ³⁴S_Σs values of the total sulfur in the subaerial basalt are reduced to 150 ± 50 ppm and $\text{?0.8 ± 0.2‰}$, respectively. The sulfate to sulfide ratio and the fractionation factor between them are also smaller, 0.01 to 0.25 and +3.0‰, respectively. Chemical and isotopic evidence strongly suggests that sulfate and sulfide in the submarine basalt are in chemical and isotopic equilibria with each other at magmatic conditions. Their relative abundance and the isotope fractionation factors may be used to estimate the $\text{?o}{}_2$ and temperature of these basalts at the time of their extrusion onto the sea floor. The observed change in sulfur chemistry and isotopic ratios from the submarine to subaerial basalts can be interpreted as degassing of the SO₂ from basalt thereby depleting sulfate and ³⁴S in basalt.The volcanic sulfur gases, predominantly SO₂, from the 1971 and 1974 fissures in Kilauea Crater have δ³⁴S values of 0.8 to 0.9%., slightly heavier than the total sulfur in the submarine basalts and definitely heavier than the subaerial basalts, in accord with the above model. However, the δ³⁴S value of sulfur gases (largely SO₂) from Sulfur Bank is 8.0%., implying a secondary origin of the sulfur. The δ³⁴S values of native sulfur deposits at various sites of Kilauea and Mauna Loa volcanos, sulfate ions of four deep wells and hydrogen sulfide from a geothermal well along the east rift zone are also reported. The high δ³⁴S values (+5 to +6%._o) found for the hydrogen sulfide might be an indication of hot basaltseawater reaction beneath the east rift zone.     

Sulfide mineralogy and sulfur isotope geochemistry of layered sills in the Deer Lake Complex,Minnesota

The Deer Lake Complex, located in north-central Minnesota, consists of a series of layered peridotite-pyroxenite-gabbro sills. Sulfide minerals occur as fine disseminations throughout pyroxenite and gabbro units, and occur more sporadically in peridotite and basal chilled margin units. Sulfide volume percentage rarely exceeds 0.5. A distinct zonation in sulfide mineralogy and sulfur isotopic composition characterizes the sills. Cobaltian pentlandite is the dominant sulfide mineral in peridotite (pd) units, with Ni-enrichment most likely linked to the serpentinization process. δ³⁴Spd values are variable, ranging from ?3.5 to +2.8‰. Sulfide assemblages in pyroxenite (px) and lower gabbro units consist of chalcopyrite, pyrrhotite, and minor pentlandite. δ³⁴S_px values range from ?1 to +1 ‰. Pyrite is the principal sulfide mineral in upper gabbro (μg) units. Its origin may be related to increased f0₂ conditions of the remaining melt and to reaction between a S-bearing volatile phase and mafic silicates. δ³⁴S_ug values range from 1 to 3.5 ‰. Sulfur isotopic values of chilled margin (2–9 ‰) and peridotite units, together with the erratic spatial distribution of sulfide minerals in these zones, suggests that the parent magma was not initially saturated with sulfur, and that local sulfide concentrations are the result of incorporation of sulfur derived from metasedimentary country rocks. Sulfide saturation was more uniformly reached during pyroxenite formation, with contained sulfur being of magmatic origin. Enrichment in ³⁴S of pyrite from upper gabbro may be explained by buildup of isotopically heavy sulfur following a Rayleigh process, coupled with possible involvement of a SO₂-rich fluid phase during hydrothermal alteration.     

Equilibria in a sulfide rich water from Enghien-les-Bains,France

A complete analysis of a sulfide rich water from a sedimentary area has been achieved. The formation of metastable sulfur species (polysulfide ions, colloidal sulfur and thiosulfate) is very important. The relative concentrations of the sulfur species is controlled by bacterial processes (Desulfovibrio and Thiobacteriaceae). Electrochemical measurements and results of the analyses are in agreement. A possible repartition of polysulfide ions is S^2?₆ ≈- S^2?₅ >S^2?₄. This repartition, although out of equilibrium, is characteristic of the processes leading to the formation of the metastable sulfur species.The water is in equilibrium with amorphous FeS formation. When sulfide, polysulfide and thiosulfate complexing of trace metals Cu, Cd and Pb is taken into account, an agreement is reached between their concentrations in water and their concentrations in the FeS precipitate.     

膏盐层在Ni-Cu-PGE硫化物矿床成矿中的作用 ——以俄罗斯诺里尔斯克矿床为例

与基性-超基性侵入体有关的Ni-Cu-PGE硫化物矿床是镍-铜-铂族元素矿床的最重要类型。传统观点认为,Ni-Cu-PGE硫化物矿床是由成矿岩浆分异演化、熔离形成的,与围岩性质关系不大。实际上,大部分基性-超基性岩浆是硫化物不饱和的,在岩浆自身演化过程中难以聚集大量硫化物而形成有经济价值的大型高品位NiCu-PGE硫化物矿床。因此,壳源硫的加入是基性-超基性岩浆中硫化物浓度达到过饱和,熔离形成Ni-Cu-PGE硫化物矿床的关键。膏盐层是富含石膏等硫酸盐(SO24-)的蒸发沉积建造,除SO24-外,还富含Cl-、CO23-、Na+、K+等盐类物质,在自然界分布广、面积大,是地壳中重要的硫源层和氧化障。但膏盐层在Ni-Cu-PGE硫化物矿床中的作用长期被忽视,制约了Ni-Cu-PGE硫化物矿床成矿找矿理论的发展。文章以世界最大的俄罗斯诺里尔斯克Ni-CuPGE硫化物矿床为例,介绍了膏盐层与矿床分布的空间关系、石膏等硫酸盐矿物在矿床和蚀变围岩中的分布、成矿元素和硫同位素组成特征及变化规律,阐明了膏盐层在成矿中的作用和控矿机理。膏盐(SO24-)的加入,可以大幅度提高成矿系统的氧逸度,将成矿岩浆中Fe2+氧化成Fe3+,形成铁氧化物,SO24-自身被还原,向成矿系统提供还原硫S2-,与Cu2+、Ni2+等结合,形成铜镍硫化物等,使基性-超基性成矿岩浆由硫化物不饱和变为过饱和,形成硫化物小液滴,在岩浆房经聚集-熔离-富集,形成岩浆型Ni-Cu-PGE硫化物矿床。除膏盐层外,富含硫化物的地层也是形成Ni-Cu-PGE硫化物矿床的重要硫源层。     

Evaluating the S-isotope fractionation associated with Phanerozoic pyrite burial

This study examines the sulfur isotope record of seawater sulfate proxies using δ³⁴S and Δ³³S to place constraints on the average global fractionation (Δ³⁴S_py) associated with pyrite formation and burial and the exponent λ that relates variations of the ³⁴S/³²S to variations of the ³³S/³²S. The results presented here use an analysis of the sulfur isotope record from seawater sulfate proxies and sedimentary sulfide to extract this quantity as the arithmetic difference between δ³⁴S of seawater sulfate and contemporaneous sulfide. It also uses an independent method that draws on inferences about the Δ³³S evolution of seawater sulfate to evaluate this further. These two methods yield similar results suggesting that Δ³⁴S_py and λ changed over the course of the Phanerozoic from slightly lower values of Δ³⁴S_py (lower values of λ) in the early Phanerozoic (Cambrian-Permian) to higher values of Δ³⁴S_py (higher values of λ) starting in the Triassic. This change of Δ³⁴S_py and the exponent λ is interpreted to reflect a change in the proportion of sulfide that was reoxidized and processed by bacterial disproportionation on a global scale. The revised record of Δ³⁴S_py also yields model pyrite burial curves making them more closely resemble model evolution curves for other element systems and global sea level curves. It is suggested that possible links to sea level may occur via changes in the area of submerged continental shelves which would provide additional loci for pyrite burial.The slightly different constraints used by the two approaches to calculate this fractionation may allow for additional information to be obtained about the sulfur cycle with future studies. For instance, the correspondence of these results suggests that the inferred variation of ³⁴S/³²S of pyrite is real, and that there is no significant missing sink of fractionated sulfur at the resolution of the present study (such as might be associated with organic sulfur). Burial of organic sulfur may, however, have been important at some times in the Phanerozoic and shorter timescale deviations between results provided by these methods may be observed with higher resolution sampling. If observed, this would suggest either that the record for pyrite (or less likely sulfate) is biased, or that another sink (possibly as organic sulfur) was important during these times in the Phanerozoic.     

Experimental data on the speciation of sulfur as a function of oxygen fugacity in basaltic melts

The speciation of sulfur as a function of oxygen fugacity was calculated in glasses of basaltic composition saturated experimentally with either sulfide or sulfate phases. The experiments were conducted on mixtures of synthetic and natural materials equilibrated at 1300 °C and 1 GPa in a piston-cylinder apparatus. Sulfur speciation was calculated by measuring the peak shift of the sulfur Kα radiation relative to a sulfide standard, whereas oxygen fugacity was calculated from the composition of olivine and spinel present in the assemblages. The results are consistent with sulfur being present as sulfite (S⁴⁺) in addition to sulfate (S⁶⁺) in oxidized melts. Therefore, sulfur speciation derived from SKα peak shifts should be seen as ”sulfate mole fraction equivalents“ (X(S⁶⁺)_eq.). Using the data available, an empiric function:

X(S6+)_eq.=0.86/(1+exp(2.89−2.23ΔFMQ))     

Origin of sulfur species in acid sulfate-chloride thermal waters,northeastern Japan

Acid sulfate-chloride thermal water samples collected together with fumarolic gases from various volcanic areas in northeastern Japan were studied chemically and isotogdically. δ³⁴S (COT) values of sulfate and hydrogen sulfide from these volcanic hot springs range from +4.0 to +31 and from ?15.0 to ?2.0% respectively, with δ³⁴S_ys value of +2.5 to +31. The δ³⁴S of the sulfate in the more saline waters tends to become smaller with increasing ratio of SO₄ to Cl, although the chemical and isotopic composition of acid thermal water within some areas may be altered by secondary processes during the discharge of the thermal waters. This trend can be explained by the reaction of the volcanic gases, having S/Cl of 4 ~ 7 and total sulfur of ~0% in δ³⁴S, with ground water at 200°C, and/or the removal of sulfide phase depleted in ³⁴S from the acid thermal water formed by the disproportionation of volcanic sulfur. The sulfur species in acid sulfate-chloride thermal water are shown to be volcanic exhalations.     

Specific-lon electrode determinations of sulfide preconcentrated from San Francisco Bay waters

Measurements of low-level dissolved-sulfide concentrations in estuarine water from San Francisco Bay have been made using the sulfide-specific electrode after preservation, separation, and preconcentration of the sulfide species. The separation and preconcentration were acheived by coprecipitation of ZnS with Zn(OH)₂ followed by collection and dissolution of the precipitate, giving concentration factors up to 160-fold Preconcentration provided sulfide solutions that were adequately measurable within the practical working range of the specific-ion electrode The sulfide detection limit with the preconcentration step is 0 02 μg/l Spike recoveries in the range of 81 to 10 1% have been achieved for laboratory-prepared samples having S²⁻ concentrations as low as 0 6 μg/l and 84 to 100% for an estuarine sample spiked in the field with 2 μg/l (S(−II) Positive correlations have been found between dissolved S(−II) concentrations and concentrations of dissolved Cd, Cu, and Ni, negative correlations have been found between bisulfide (HS⁻) activity and activities of Cd²⁺, Cu²⁺, and Ag⁺ species     

Sulfur isotope and trace element data from ore sulfides in the Noranda district (Abitibi,Canada): implications for volcanogenic massive sulfide deposit genesis

We examine models for volcanogenic massive sulfide (VMS) mineralization in the ~2.7-Ga Noranda camp, Abitibi subprovince, Superior Province, Canada, using a combination of multiple sulfur isotope and trace element data from ore sulfide minerals. The Noranda camp is a well-preserved, VMS deposit-rich area that is thought to represent a collapsed volcanic caldera. Due to its economic value, the camp has been studied extensively, providing a robust geological framework within which to assess the new data presented in this study. We explore previously proposed controls on mineralization within the Noranda camp and, in particular, the exceptional Au-rich Horne and Quemont deposits. We present multiple sulfur isotope and trace element compositional data for sulfide separates representing 25 different VMS deposits and “showings” within the Noranda camp. Multiple sulfur isotope data for this study have δ³⁴S_V-CDT values of between ?1.9 and +2.5?‰, and Δ³³S_V-CDT values of between ?0.59 and ?0.03?‰. We interpret the negative Δ³³S values to be due to a contribution of sulfur that originated as seawater sulfate to form the ore sulfides of the Noranda camp VMS deposits. The contribution of seawater sulfate increased with the collapse and subsequent evolution of the Noranda caldera, an inference supported by select trace and major element analyses. In particular, higher concentrations of Se occur in samples with Δ³³S values closer to 0?‰, as well as lower Fe/Zn ratios in sphalerite, suggesting lower pressures and temperatures of formation. We also report a relationship between average Au grade and Δ³³S values within Au-rich VMS deposits of the Noranda camp, whereby higher gold grades are associated with near-zero Δ³³S values. From this, we infer a dominance of igneous sulfur in the gold-rich deposits, either leached from the volcanic pile and/or directly degassed from an associated intrusion.