Investigation of turbulence characteristics in channel with dense vegetation

In this experimental study,the turbulent flow in a channel with vegetation by using sprouts of wheat on channel bed was investigated.Two different aspect ratios of channel were used.An Acoustic Doppler Velocimetry was used to measure parameters of turbulent flow over submerged sprouts of wheat,such as velocity profiles.The log law and the Reynolds shear stress distribution were applied. Results indicate that the position of the maximum turbulence intensity superposes on the inflection point situated over the top of submerged vegetation cover.Quadrant analysis shows that near the vegetation bed,the sweeps and ejections appear to be the most dominant phenomenon,while far from the vegetated bed,the outward is dominant event.Results also show that the aspect ratio plays an important role on the contribution of the different bursting events for Reynolds stress determination.     

Spatial variability of three‐dimensional Reynolds stresses in a developing channel bend

Experimental results of the mean flow field and turbulence characteristics for flow in a model channel bend with a mobile sand bed are presented. Acoustic Doppler velocimeters (ADVs) were used to measure the three components of instantaneous velocities at multiple cross sections in a 135° channel bend for two separate experiments at different stages of clear water scour conditions. With measurements at multiple cross sections through the bend it was possible to map the changes in both the spatial distribution of the mean velocity field and the three Reynolds shear stresses. Turbulent stresses are known to contribute to sediment transport and the three‐dimensionality inherent to flow in open channel bends presents a useful case for determining specific relations between three‐dimensional turbulence and sediment entrainment and transport. These measurements will also provide the necessary data for validating numerical simulations of turbulent flow and sediment transport. The results show that the magnitude and distribution of three‐dimensional Reynolds stresses increase through the bend, with streamwise‐cross stream and cross stream‐vertical components exceeding the maximum principal Reynolds stress through the bend. The most intriguing observation is that near‐bed maximum positive streamwise‐cross stream Reynolds stress coincides with the leading edge of the outer bank scour hole (or thalweg), while maximum cross stream‐vertical Reynolds stress (in combination with high negative streamwise‐cross stream Reynolds stress near the bend apex) coincides with the leading edge of the inner bank bar. Maximum Reynolds stress and average turbulent kinetic energy appear to be greater and more localized over the scour hole before final equilibrium scour is reached. This suggests that the turbulent energy in the flow is higher while the channel bed is developing, and both lower turbulent energy and a broader distribution of turbulent stresses near the bed are required for cessation of particle mobilization and transport. Copyright © 2010 John Wiley & Sons, Ltd.     

Effect of non‐uniformity of flow on velocity and turbulence intensities over a cobble‐bed

Non‐uniform flows encompassing both accelerating and decelerating flows over a cobble‐bed flume have been experimentally investigated in a flume at a scale of intermediate relative submergence. Measurements of mean longitudinal flow velocity u, and determinations of turbulence intensities u′, v′, w′, and Reynolds shear stress ?u_fw_f have been made. The longitudinal velocity distribution was divided into the inner zone close to the bed and the outer zone far from the bed. In the inner zone of the boundary layer (near the bed) the velocity profile closely followed the ‘Log Law’; however, in the outer zone the velocity distribution deviated from the Log Law consistently for both accelerating and decelerating flows and the changes in bed slopes ranging from ?2% to + 2% had no considerable effect on the outer zone. For a constant bed slope (S = ±0·015), the larger the flow rate, the smaller the turbulence intensities. However, no detectable pattern has been observed for u′, v′ and w′ distributions near the bed. Likewise, for a constant flow rate (Q = 0·040 m³/s), with variation in bed slope the longitudinal turbulent intensity profile in the longitudinal direction remained concave for both accelerating and decelerating flows; whereas vertical turbulent intensity (w′) profile presented no specific form. The results reveal that the positions of maximum values of turbulence intensities and the Reynolds shear stress depend not only on the flow structure (accelerating or decelerating) but also on the intermediate relative submergence scale. Copyright © 2009 John Wiley & Sons, Ltd.     

Turbulence characteristics of flows passing through a tetrahedron frame in a smooth open-channel

The turbulence characteristics of flows passing through a tetrahedron frame were investigated by using a 2-dimensional fiber-optic laser Doppler velocimeter (2-D FLDV). Experiments for uniform flows with different bed slopes under both submerged and un-submerged conditions were carried out in a re-circulating flume with glass side walls. The experimental bed was a smooth fixed bed. It was observed that with the tetrahedron frame the mean longitudinal velocity decrease in the retardation zone. However, both the longitudinal and the vertical turbulence intensities are larger than those for the undisturbed approach flow. The tetrahedron frame may reduce the probability of sediment entrainment by retarding the flow and reducing the boundary shear stress. In addition, it may induce sediment deposition in a sediment laden flow by changing the flow direction and increasing the energy dissipation.     

Effect of slope angle of an artificial pool on distributions of turbulence

Experiments were carried out over a 2-dimentional pool with a constant length of 1.5 m and four different slopes.The distributions of velocity,Reynolds stress and turbulence intensities have been studied in this paper.Results show that as flow continues up the exit slope,the flow velocity increases near the channel bed and decreases near the water surface.The flow separation was not observed by ADV at the crest of the bed-form.In addition,the length of the separation zone increases with the increasing of entrance and exit slopes.The largest slope angle causes the maximum normalized shear stress.Based on the experiments,it is concluded that the shape of Reynolds stress distribution is generally dependent on the entrance and exit slopes of the pool.Also,the shape of Reynolds stress distribution is affected by both decelerating and accelerating flows.Additionally,with the increase in the slope angle,secondary currents are developed and become more stable.Results of the quadrant analysis show that the momentum between flow and bed-form is mostly transferred by sweep and ejection events.     

Sheet flow hydrodynamics over a non-uniform sand bed channel

The current study experimentally investigates the flow characteristics and temporal variations in the sheet flow profile of a non-uniform sand bed channel. Experiments were done to explore turbulent structures in the presence of a sheet flow layer with and without seepage. The turbulent events, such as stream wise velocity, Reynolds shear stresses, and turbulence intensities were found to be increasing and vertical velocity was found decreasing with a sheet layer. The presence of a sheet layer also effects the turbulent energy production and energy dissipation. All the turbulence parameters with and without a sheet layer have also been influenced by the presence of downward seepage. The rate of sheet flow movement is increased with seepage, owing to increased turbulence with seepage. The current study used wavelet analysis on temporally lagged spatial bed elevation profiles obtained from a set of laboratory experiments and synchronized the wavelet coefficients with bed elevation fluctuation at different spatial scales. A spatial cross correlation analysis at multiple scales, based on the wavelet coefficients, has been done on these bed elevation datasets to observe the effect of downward seepage on the dynamic behavior of sheet flow at different length scales. It is found that seepage increases average bed celerity and also increases the celerity of sheet flow of similar length scales. This increase in the celerity has been hypothesized as the increase of sheet flow movement as well as the increase in turbulent parameters with seepage, which destabilizes the bed particles resulting in a disruption in the continuous propagation pattern of the sheet flow. The increase of sheet flow celerity with seepage is confirmed from the saturation level of the wavelet power spectra of the bed elevation series. The presence of seepage also affects the non-uniformity of collective sheet material.     

Flow structure over a wavy bed with vegetation cover

On the basis of experiments carried out in flume with a wavy bed with vegetation cover, flow velocity, turbulence intensities and Reynolds stress distributions are investigated. The wavy bed was similar to dune in this study. The fixed artificial dunes were constructed over the bed and artificial vegetation put over them in a laboratory flume. An Acoustic Doppler Velocimeter and spatially-averaged method were applied to determine turbulent flow components and shear velocity. Results were compared with a gravel bedform. It was observed that vegetation cover influences considerably the flow structure and displays clearly the flow separation and reattachment point. The law of the wall was not valid within the vegetation cover, but it was fitted well to the zone above the vegetation cover within the inner layer. For a wavy bed having the same dimensions, shear velocity and friction factor over vegetation cover are 1.7 and 2.6 times of those for the gravel bedform, respectively. The results of laboratory study were compared with those of river study.     

Large-eddy simulation of the turbulent structure in compound open-channel flows

A large-eddy simulation study has been undertaken to investigate the turbulent structure of open-channel flow in an asymmetric compound channel. The dynamic sub-grid scale model has been employed in the model, with the partial cell treatment being implemented using a Cartesian grid structure to deal with the floodplain. The numerical model was used to predict the: primary velocity and secondary currents, boundary shear stress, turbulence intensities, turbulent kinetic energy, and Reynolds stresses. These parameters were compared with experimental measurements published in the literature, with relatively close agreement being obtained between both sets of results. Furthermore, instantaneous flow fields and large-scale vortical structures were predicted and are presented herein. These vortical structures were found to be responsible for the significant lateral exchange of mass and momentum in compound channels.     

Turbulence structures in non-uniform flows

This study investigates turbulence structures in steady and non-uniform flows. Equations of Reynolds shear stress and turbulent velocity fluctuations are derived and their physical interpretations are explained. The theoretical results show that, different from previous studies, the variation of water surface can generate the wall-normal velocity, resulting in deviations of Reynolds shear stress and turbulence intensities from those in uniform flows. A self-similarity relationship is found between the Reynolds shear stress and turbulence intensities in non-uniform flows. The existence of self-similarity indicates that the effect of non-uniformity does not influence the mixing length. An empirical equation has been proposed to express the relationship based on experimental data available in the literature. Good agreement is achieved between the measured and predicted turbulence intensities by applying the self-similarity relationship.     

Measuring water velocity in highly turbulent flows: field tests of an electromagnetic current meter (ECM) and an acoustic Doppler velocimeter (ADV)

Two field tests were completed to compare the performance of an electromagnetic current meter (ECM) with that of an acoustic Doppler velocimeter (ADV) in gravel‐bed rivers. Research was particularly motivated by the need to measure flow properties in highly energetic turbulent flows. Measurements were made at two field sites, one at moderate velocities (up to 70 cm/s) and with moderate turbulence intensities (10–20% of mean flow), and the other in an area of non‐uniform flow that included locations with fast mean velocities (up to 1.75 m/s) and high turbulent intensities (up to 50% of mean flow). Comparison of means, standard deviations, turbulent kinetic energy and Reynolds shear stress confirm the general agreement between the ECMs and ADVs. The general agreement is subject to limitations associated with the sample volume and frequency response of the instruments, and only applies within restricted velocity (up to ≈1.25 m/s) and turbulence intensity ranges (up to ≈0·125 m/s). At higher turbulence intensities, spectral analysis showed anomalous behavior of the ADV signal, especially in the vertical velocity component. Quadrant analysis of the Reynolds stress suggests that these problems occur predominantly in quadrants 1 and 3. Errors in ADV measurements were estimated using four different methods: one that utilized the characteristic noise floor in spectral plots, one based on internal ADV measurements of signal correlation and two techniques that aggregate errors related to various sub‐factors. Estimates were divergent at high flows. Techniques that rely on sub‐factors appeared to underestimate the impact of high turbulence on signal quality. The key conclusion for future field applications is that the older ECM technology provides the more reliable estimates of flow parameters in high turbulence. Copyright © 2007 John Wiley & Sons, Ltd.     

Near‐bed shear stress,turbulence production and dissipation in a shallow and narrow tidal channel

Near‐bed, highly resolved velocity profiles were measured in the lower 0.03 m of the water column using acoustic Doppler profiling velocimeters in narrow tidal channels in a salt marsh. The bed shear stress was estimated from the velocity profiles using three methods: the log‐law, Reynolds stress, and shear stress derived from the turbulent kinetic energy (TKE). Bed shear stresses were largest during ebbing tide, while near‐bed velocities were larger during flooding tide. The Reynolds stress and TKE method gave similar results, while the log‐law method resulted in smaller bed shear stress values during ebbing tide. Shear stresses and turbulent kinetic energy followed a similar trend with the largest peaks during ebbing tide. The maximum turbulent kinetic energy was on the order of 1 × 10^{? 2} m²/s². The fluid shear stress during flooding tide was approximately 30% of the fluid shear stress during ebbing tide. The maximum TKE‐derived shear stress was 0.7 N/m² and 2.7 N/m² during flooding and ebbing tide, respectively, and occurred around 0.02 m above the bed. Turbulence dissipation was estimated using the frequency spectrum and structure function methods. Turbulence dissipation estimates from both methods were maximum near the bed (~0.01 m). Both the structure function and the frequency spectrum methods resulted in maximum dissipation estimates on the order of 4 × 10^{? 3} m²/s³. Turbulence production exceeded turbulence dissipation at every phase of the tide, suggesting that advection and vertical diffusion are not negligible. However, turbulence production and dissipation were within a factor of 2 for 77% of the estimates. The turbulence production and dissipation decreased quickly away from the bed, suggesting that measurements higher in the water column cannot be translated directly to turbulence production and dissipation estimates near the bed. Copyright © 2015 John Wiley & Sons, Ltd.     

Mean and turbulent flow fields in a simulated ice‐covered channel with a gravel bed: some laboratory observations

Northern rivers experience freeze‐up over the winter, creating asymmetric under‐ice flows. Field and laboratory measurements of under‐ice flows typically exhibit flow asymmetry and its characteristics depend on the presence of roughness elements on the ice cover underside. In this study, flume experiments of flows under a simulated ice cover are presented. Open water conditions and simulated rough ice‐covered flows are discussed. Mean flow and turbulent flow statistics were obtained from an Acoustic Doppler Velocimeter (ADV) above a gravel‐bed surface. A central region of faster flow develops in the middle portion of the flow with the addition of a rough cover. The turbulent flow characteristics are unambiguously different when simulated ice covered conditions are used. Two distinct boundary layers (near the bed and in the vicinity of the ice cover, near the water surface) are clearly identified, each being characterized by high turbulent intensity levels. Detailed profile measurements of Reynolds stresses and turbulent kinetic energy indicate that the turbulence structure is strongly influenced by the presence of an ice cover and its roughness characteristics. In general, for y/d > 0·4 (where y is height above bed and d is local flow depth), the addition of cover and its roughening tends to generate higher turbulent kinetic energy values in comparison to open water flows and Reynolds stresses become increasingly negative due to increased turbulence levels in the vicinity of the rough ice cover. The high negative Reynolds stresses not only indicate high turbulence levels created by the rough ice cover but also coherent flow structures where quadrants one and three dominate. Copyright © 2012 John Wiley & Sons, Ltd.     

Experimental investigation on local shear stress and turbulence intensities over a rough non-uniform bed with and without sediment using 2D particle image velocimetry

The current work focuses on locally resolving velocities,turbulence,and shear stresses over a rough bed with locally non-uniform character.A nonporous subsurface layer and fixed interfacial sublayer of gravel and sand were water-worked to a nature-like bed form and additionally sealed in a hydraulic flume.Two-dimensional Particle Image Velocimetry(2 D-PIV) was applied in the vertical plane of the experimental flume axis.Runs with clear water and weak sediment transport were done under slightly supercritical flow to ensure sediment transport conditions without formation of considerable sediment deposits or dunes.The study design included analyzing the double-averaged flow parameters of the entire measurement domain and investigating the flow development at 14 consecutive vertical subsections.Local geometrical variabilities as well the presence of sediment were mainly reflected in the vertical velocity component.Whereas the vertical velocity decreased over the entire depth in presence of sediment transport,the streamwise velocity profile was reduced only within the interfacial sublayer.In the region with decelerating flow conditions,however,the streamwise velocity profile systematically increased along the entire depth extent.The increase in the main velocity(reduction of flow resistance)correlated with a decrease of the turbulent shear and main normal stresses.Therefore,effects of rough bed smoothening and drag force reduction were experimentally documented within the interfacial sublayer due to mobile sediment.Moreover,the current study leads to the conclusion that in nonuniform flows the maximum Reynolds stress values are a better predictor for the bed shear stress than the linearly extrapolated Reynolds stress profile.This is an important finding because,in natural flows,uniform conditions are rare.     

Turbulent flow structures in alluvial channels with curved cross‐sections under conditions of downward seepage

Experimental investigations have been done to analyze turbulent structures in curved sand bed channels with and without seepage. Measures of turbulent statistics such as time‐averaged near‐bed velocities, Reynolds stresses, thickness of roughness sublayer and shear velocities were found to increase with application of downward seepage. Turbulent kinetic energy and Reynolds normal stresses are increased in the streamwise direction under the action of downward seepage, causing bed particles to move rapidly. Analysis of bursting events shows that the relative contributions of all events (ejections, sweeps and interactions) increase throughout the boundary layer, and the thickness of the zone of dominance of sweep events, which are responsible for the bed material movement, increases in the case of downward seepage. The increased sediment transport rate due to downward seepage deforms the cross‐sectional geometry of the channel made of erodible boundaries, which is caused by an increase in flow turbulence and an associated decrease in turbulent kinetic energy dissipation and turbulent diffusion.     

Turbulent kinetic energy budget in a gravel-bed channel flow

The present experimental investigation focuses on the characteristics of near bed turbulence in a fully rough, uniform open-channel flow over a gravel-type bed. Due to bed topography small scale heterogeneity, the flow is not uniform locally in the near bed region and a double averaging methodology is applied over a length scale much larger than the gravel size. The double-averaged Turbulent Kinetic Energy (TKE) budget derived in the context of the present flow over a gravel bed differs from the TKE budget written for flow over a vegetation canopy. The non-constant shape of the roughness function measured in our gravel bed leads to an additional bed-induced production term which is null for vertical roughness elements, such as simplified vegetation elements. The experimental estimation of the terms of the TKE budget reveals that the maximum turbulent activity takes place away from the reference plane, near the roughness crests. However, within the interface sublayer the work of the bed induced velocity fluctuations against the Reynolds stress is of the same magnitude as the main turbulence production term. Consequently, the characteristics of the TKE budget have similarities with uniform flows over canopies and strongly differ from uniform flows over smooth and transitionally rough flows over sedimentlike beds.     

Turbulence in mobile-bed streams

This study is devoted to quantify the near-bed turbulence parameters in mobile-bed flows with bed-load transport. A reduction in near-bed velocity fluctuations due to the decrease of flow velocity relative to particle velocity of the transporting particles results in an excessive near-bed damping in Reynolds shear stress (RSS) distributions. The bed particles are associated with the momentum provided from the flow to maintain their motion overcoming the bed resistance. It leads to a reduction in RSS magnitude over the entire flow depth. In the logarithmic law, the von Kármán coefficient decreases in presence of bed-load transport. The turbulent kinetic energy budget reveals that for the bed-load transport, the pressure energy diffusion rate near the bed changes sharply to a negative magnitude, implying a gain in turbulence production. According to the quadrant analysis, sweep events in mobile-bed flows are the principal mechanism of bed-load transport. The universal probability density functions for turbulence parameters given by Bose and Dey have been successfully applied in mobile-bed flows.     

Current and turbulence measurements at the FINO1 offshore wind energy site: analysis using 5-beam ADCPs

We report concurrent measurements of ocean currents and turbulence at two sites in the North Sea, one site at upwind of the FINO1 platform and the other 200-m downwind of the Alpha Ventus wind farm. At each site, mean currents, Reynolds stresses, turbulence intensity and production of turbulent kinetic energy are obtained from two bottom-mounted 5-beam Nortek Signature1000s, high-frequency Doppler current profiler, at a water depth of approximately 30 m. Measurements from the two sites are compared to statistically identify the effects of wind farm and waves on ocean current variability and the turbulent structure in the water column. Profiles of Reynolds stresses are found to be sensible to both environmental forcing and the wind farm wake-induced distortions in both boundary layers near the surface and the seabed. Production of turbulent kinetic energy and turbulence intensity exhibit approximately similar, but less pronounced, patterns in the presence of farm wake effects.     

Flow fields around tandem and staggered piers on a mobile bed

An experimental investigation on flow fields within the scour holes upstream and downstream of circular piers positioned in tandem and staggered arrangements is reported and compared with isolated piers on mobile beds with uniform sediment. The instantaneous bed elevations and instantaneous three dimensional (3D) velocities were measured using a 5 MHz Ultrasonic Ranging system and 16 MHz micro down looking acoustic Doppler velocimeter, respectively. The velocity and flow depth were measured at different locations under near equilibrium bed scour conditions. The measured 3D velocities were processed for the computation of flow parameters, such as velocity fields, streamline patterns, vorticity fields, and circulation. Furthermore, turbulence intensities, turbulent kinetic energy, Reynolds shear stresses, and bed shear stresses around the piers for all three pier configurations were computed from the detrended velocity signals to identify significant differences in the flow parameters and turbulence in the tandem and staggered pier arrangements as compared to those for an isolated pier. A recirculation zone was found near the bed in front of the rear pier in the tandem case from the streamline patterns. The vortices in the bi-vortex system were observed to be opposite to each other in the gap between the three piers in the staggered case. A strong secondary vortex also was observed apart from the primary vortex at the foot of the pier (θ = 0°) in all the three configurations. The strength of the horseshoe vortex (combination of primary and secondary vortices) was found to be higher at the front piers of the staggered arrangement as compared to those of the tandem piers, followed by the isolated pier. The bed shear stresses were found to be higher for the staggered piers than for the tandem piers in the direction of flow (θ = 0°). However, a 50% reduction in the bed shear stresses was observed behind the tandem piers at θ = 180°. The study reported in this paper provides the foundation for further investigation of countermeasures against local scour around tandem and staggered bridge piers on a mobile bed with non-uniform sediment.     

Contributions of burst-sweep cycles to Reynolds shear stress over fluvial obstacle marks generated in a laboratory flume

This paper investigates the phenomena of turbulent bursting events,and to make a comparative study among the events in the scour geometry developed by short circular cylinders of fixed length with different diameters placed on the sand bed transverse to the flow.The distributions of turbulent kinetic energy(TKE),turbulent diffusion in both longitudinal and vertical directions at different locations of scour marks,and the contributions of burst-sweep cycles to the Reynolds shear stress are presented.     

Turbulence modeling of compound open-channel flows with and without vegetation on the floodplain using the Reynolds stress model

A Reynolds stress model for the numerical simulation of compound open-channel flows with vegetation on the floodplain is described. The Reynolds stress model consists of various sub-models such as Speziale et al.’s model, Mellor and Herring’s model, and Rotta’s model for the pressure–strain correlation term, the turbulent diffusion term, and the dissipation term, respectively. For validation of the model, plain compound open-channel flows are simulated. The computed results were compared with measured data by [Tominaga A, Nezu I. Turbulent structure in compound open-channel flows. J Hydraul Eng, ASCE 1991;117(1):21–41] and the results show that the Reynolds stress model successfully simulates the mean flow and turbulence structure of plain compound channel flows. The model was then applied to compound open-channel flows with vegetated floodplains. Good agreement between the simulated results and data from an algebraic stress model by [Naot D, Nezu I, Nakagawa H. Hydrodynamic behavior of partly vegetated open channels. J Hydraul Eng, ASCE 1996;122(11):625–33] was found. However, it was shown that the RSM is capable of predicting the velocity dip and lateral shift in the maximum streamwise velocity, which were not observed in the data from algebraic stress modeling. Finally, a depth-averaged analysis of the streamwise momentum equation was performed to investigate the lateral momentum transfer in compound channel flows with vegetated floodplains. Compared with components by the secondary currents and Reynolds stress, the drag force due to the presence of vegetation appears to be a factor in reducing the bottom shear stress in both main channel and floodplain.