共查询到20条相似文献,搜索用时 15 毫秒
1.
在高频面波方法中,水平分辨率是指水平方向上分辨异常体的能力.异常体在水平方向上的长度可用水平方向上横波速度的异常尺度来确定.面波多道分析(MASW)方法被广泛应用于浅地表横波速度结构的探测,然而该方法确定的横波速度是整个检波器排列的平均计算结果,因此水平分辨率较差.另外,采用共中心点(CMP)多次覆盖的方式采集数据亦增加了野外的工作量.我们在MASW方法的基础上,应用面波层析成像方法,提出一套提高面波勘探水平分辨率的完整方法的技术流程.首先,利用波场分离技术获得准确的基阶或高阶模式面波,采用相位扫描的互相关方法测量多道面波记录中任意两道之间的面波走时;然后根据面波层析成像方法,获得高分辨率的各目标网格内的纯路径相速度频散曲线;最后反演所有目标网格内的纯路径相速度频散曲线,得到研究区域的拟二维横波速度结构.这套方法具有一定的抗噪能力,理论上它可以准确地提取相邻两道之间面波的相速度频散曲线;同时由于该方法最少只需要1个排列就可以获得拟二维横波速度结构,因此它显著减小了野外工作量.理论模型和实际资料都证实了这套方法可有效提高面波勘探的水平分辨率. 相似文献
2.
Multichannel Analysis of Surface Waves utilizes a multichannel recording system to estimate near-surface shear (S)-wave velocities from high-frequency Rayleigh waves. A pseudo-2D S-wave velocity ( vS) section is constructed by aligning 1D models at the midpoint of each receiver spread and using a spatial interpolation scheme. The horizontal resolution of the section is therefore most influenced by the receiver spread length and the source interval. The receiver spread length sets the theoretical lower limit and any vS structure with its lateral dimension smaller than this length will not be properly resolved in the final vS section. A source interval smaller than the spread length will not improve the horizontal resolution because spatial smearing has already been introduced by the receiver spread.In this paper, we first analyze the horizontal resolution of a pair of synthetic traces. Resolution analysis shows that (1) a pair of traces with a smaller receiver spacing achieves higher horizontal resolution of inverted S-wave velocities but results in a larger relative error; (2) the relative error of the phase velocity at a high frequency is smaller than at a low frequency; and (3) a relative error of the inverted S-wave velocity is affected by the signal-to-noise ratio of data. These results provide us with a guideline to balance the trade-off between receiver spacing (horizontal resolution) and accuracy of the inverted S-wave velocity. We then present a scheme to generate a pseudo-2D S-wave velocity section with high horizontal resolution using multichannel records by inverting high-frequency surface-wave dispersion curves calculated through cross-correlation combined with a phase-shift scanning method. This method chooses only a pair of consecutive traces within a shot gather to calculate a dispersion curve. We finally invert surface-wave dispersion curves of synthetic and real-world data. Inversion results of both synthetic and real-world data demonstrate that inverting high-frequency surface-wave dispersion curves – by a pair of traces through cross-correlation with phase-shift scanning method and with the damped least-square method and the singular-value decomposition technique – can feasibly achieve a reliable pseudo-2D S-wave velocity section with relatively high horizontal resolution. 相似文献
3.
Multichannel analysis of surface waves (MASW) method is a non-invasive geophysical technique that uses the dispersive characteristic
of Rayleigh waves to estimate a vertical shear (S)-wave velocity profile. A pseudo-2D S-wave velocity section is constructed
by aligning 1D S-wave velocity profiles at the midpoint of each receiver spread that are contoured using a spatial interpolation
scheme. The horizontal resolution of the section is therefore most influenced by the receiver spread length and the source
interval. Based on the assumption that a dipping-layer model can be regarded as stepped flat layers, high-resolution linear
Radon transform (LRT) has been proposed to image Rayleigh-wave dispersive energy and separate modes of Rayleigh waves from
a multichannel record. With the mode-separation technique, therefore, a dispersion curve that possesses satisfactory accuracy
can be calculated using a pair of consecutive traces within a mode-separated shot gather. In this study, using synthetic models
containing a dipping layer with a slope of 5, 10, 15, 20, or 30 degrees and a real-world example, we assess the ability of
using high-resolution LRT to image and separate fundamental-mode Rayleigh waves from raw surface-wave data and accuracy of
dispersion curves generated by a pair of consecutive traces within a mode-separated shot gather. Results of synthetic and
real-world examples demonstrate that a dipping interface with a slope smaller than 15 degrees can be successfully mapped by
separated fundamental waves using high-resolution LRT. 相似文献
4.
Rayleigh波可以用来反演近地表结构,在工程物探、石油物探、地球内部结构探测中均有重要意义.数值计算得到的含低速层的层状介质对应的Rayleigh波频散曲线会出现看似“交叉”的现象,但是对于这种现象目前还没有进行系统的研究.事实上可以验证,有些看似交叉的频散曲线实际上不相交.改变低速层的厚度和横波速度发现低速层越明显(即低速层速度越低或层厚越厚)频散曲线越不容易相交.凡友华等在2007年提出频散曲线对应着四种基本模式,在频散曲线发生“交叉”现象的区域实际上存在两个以上模式的频散曲线.本文主要研究了存在R模和S2模的区域内频散曲线的“交叉”现象.首先利用竖直本征振动曲线研究R模和S2模Rayleigh 波的振动特点,发现R模对应的本征振动主要集中在地表,随着深度变化能量快速衰减,S2模对应的本征振动主要集中在第2层.研究“交叉点”附近频散点对应的本征振动曲线发现这一区域有些Rayleigh波同时具有R模和S2模的振动特点,对应着一种耦合模式.通过对实例的研究发现,在“交叉点”附近,若两条频散曲线不发生交叉,则每条曲线对应的模式会发生R模和S2模之间经由耦合模式的转变,本文称这种现象为两种模式发生耦合;若两条频散曲线相交,则同一条频散曲线上的Rayleigh波模式几乎相同,只是在离交点很近的区域会存在一些耦合模式,本文称此时两种模式不发生耦合.本文研究结果主要供Rayleigh波对低速层结构的反演研究参考. 相似文献
5.
面波频散曲线对于横波速度、纵波速度、层厚等近地表地球物理参数的敏感度相差较大, 现阶段通过频散曲线可以获得较为精确的近地表横波速度与厚度信息, 但无法直接对纵波速度进行反演.研究表明, 泊松比对于波长(W)-探测深度(D)关系较为敏感.基于这一发现, 本文根据频散曲线与反演获取的横波速度结构计算平均速度, 获取W-D关系曲线.但合成数据测试证明, 因近地表浅层对应的W-D曲线变化较小, 且浅层纵波速度反演不准确会使误差累积, 直接反演W-D曲线无法获取可靠的纵波速度剖面.本文改进了基于平均速度分析的近地表纵波速度反演方法, 在目标函数中加入了对浅层信息较为敏感的W/D-D信息, 同时对W-D曲线与W/D-D曲线进行联合反演.合成数据测试证明可以获取较为准确地浅层与深层纵波速度.将该方法应用于实际地震数据中, 联合反演得到的纵波速度剖面与微测井数据较为吻合, 证明本文提出的方法可以不借助其他信息, 仅通过面波频散信息, 获取更为准确地近地表纵波信息. 相似文献
6.
深反射地震剖面法为了获取深部结构特征常常采取大的偏移距采集数据.目前公开发表的相关资料中,鲜有利用深反射地震炮集数据获取近地表的结构特征.为此,本文通过正演测试了相关数据处理流程,即利用有限差分正演了起伏地表模型的大偏移距地震单炮弹性波场特征,通过共检波点域面波信号F-K频谱叠加构建新方法,从深反射地震数据集中提取了高品质的多阶面波频散曲线,再利用多阶面波联合反演获得了近地表的结构特征.在前述正演流程基础上,利用跨越班公湖—怒江缝合带的SinoProbe深反射地震剖面中的实际炮集数据,求取了基阶和一阶瑞利波频散曲线,联合反演后得到近地表横波速度结构.该结果与初至波走时反演获取的纵波速度结构具有较好的一致性,且在近地表的浅层分辨率较纵波速度结构特征更高,而更与已有地质认识相吻合.本文提供的相关数据处理流程表明利用深反射地震炮集数据,也能够获取近地表浅层的横波速度结构. 相似文献
7.
深反射地震剖面法为了获取深部结构特征常常采取大的偏移距采集数据.目前公开发表的相关资料中,鲜有利用深反射地震炮集数据获取近地表的结构特征.为此,本文通过正演测试了相关数据处理流程,即利用有限差分正演了起伏地表模型的大偏移距地震单炮弹性波场特征,通过共检波点域面波信号F-K频谱叠加构建新方法,从深反射地震数据集中提取了高品质的多阶面波频散曲线,再利用多阶面波联合反演获得了近地表的结构特征.在前述正演流程基础上,利用跨越班公湖—怒江缝合带的SinoProbe深反射地震剖面中的实际炮集数据,求取了基阶和一阶瑞利波频散曲线,联合反演后得到近地表横波速度结构.该结果与初至波走时反演获取的纵波速度结构具有较好的一致性,且在近地表的浅层分辨率较纵波速度结构特征更高,而更与已有地质认识相吻合.本文提供的相关数据处理流程表明利用深反射地震炮集数据,也能够获取近地表浅层的横波速度结构. 相似文献
8.
作为近地表横波速度结构成像的主要手段之一,面波多道分析法的正问题研究对现场观测系统设计及后续反演计算具有重要意义.目前面波频散曲线的正演主要分为两类:一是对水平层状介质中面波的本征值问题进行求解,该类方法计算效率高但较难考虑地下介质在横向上的不均匀性;二是基于波动方程的全波场模拟,该类方法在理论上可考虑任意复杂的地质模... 相似文献
9.
The lithospheric structure of the Sinai Peninsula is shown by means of nine shear velocity profiles for depths ranging from
zero to 50 km, determined from the Rayleigh wave analysis. The traces of 30 earthquakes, which occurred from 1992 to 1999
in and around the study area, have been used to obtain Rayleigh wave dispersion. These earthquakes were registered by a broadband
station located in Egypt (KEG station). The dispersion curves were obtained for periods between 3 and 40 s, by digital filtering
with a combination of MFT and TVF filtering techniques. After that, all seismic events were grouped in source zones to obtain
a dispersion curve for each source-station path. These dispersion curves were inverted according to generalized inversion
theory, to obtain shear wave velocity models for each source-station path, which is the main goal of this study. The shear
velocity structure obtained for the Sinai Peninsula is shown through the shear velocity distributions with depth. These results
agree well with the geology and other geophysical results, previously obtained from seismic and gravity data. The obtained
velocity models suggest the existence of lateral and vertical heterogeneity. The shear velocity increases generally with depth
for all paths analyzed in the study area. Nevertheless, in some paths a small low velocity channel in the upper or lower crust
occurs. Along these profiles, it is found that the crustal structure of the Sinai Peninsula consists of three principal layers:
upper crust with a sedimentary layer and lower crust. The upper crust has a sedimentary cover of 2 km thick with an average
S-velocity of 2.53 km/s. This upper crust has a variable thickness ranging from 12 to 18 km, with S-wave velocity ranging
from 3.24 to 3.69 km/s. The Moho discontinuity is located at a depth of 30 km, which is reflected by a sharp increase in the
S-velocity values that jump from 3.70–4.12 to 4.33–4.61 km/s. 相似文献
10.
瑞利波频散特性测试是波速结构的面波探测方法中的关键环节。本文不进行速度结构的比较,而是直接与表面波谱分析方法比较所提取的频散曲线,从而将反演方法可能引入的不确定性因素剥离了出去,能够更客观地说明地脉动台阵方法的有效性和精度。在唐山26个场地进行的两种方法中美联合观测和分析结果表明。地脉动方法在83%的场地达到了与表面波谱分析方法相同的精度,是一种经济有效的场地瑞利波频散特性和波速结构测试方法。 相似文献
11.
The Ningdu basin, located in southern Jiangxi province of southwest China, is one of the Mesozoic basin groups which has exploration prospects for geothermal energy. A study on the detailed velocity structure of the Ningdu basin can provide important information for geothermal resource exploration. In this study, we deployed a dense seismic array in the Ningdu basin to investigate the 3D velocity structure and discuss implications for geothermal exploration and geological evolution. Based on the dense seismic array including 35 short-period (5 s-100 ?Hz) seismometers with an average interstation distance of ~5 ?km, Rayleigh surface wave dispersion curves were extracted from the continuous ambient noise data for surface wave tomographic inversion. Group velocity tomography was conducted and the 3D S-wave velocity structure was inverted by the neighborhood algorithm. The results revealed obvious low-velocity anomalies in the center of the basin, consistent with the low-velocity Cretaceous sedimentary rocks. The basement and basin-controlling fault can also be depicted by the S-wave velocity anomalies. The obvious seismic interface is about 2 ?km depth in the basin center and decreases to 700 ?m depth near the basin boundary, suggesting spatial thickness variations of the Cretaceous sediment. The fault features of the S-wave velocity profile coincide with the geological cognition of the western boundary basin-controlling fault, which may provide possible upwelling channels for geothermal fluid. This study suggests that seismic tomography with a dense array is an effective method and can play an important role in the detailed investigations of sedimentary basins. 相似文献
12.
收集了南北地震带区域地震台网中292个地震台站2008年1月至2011年3月期间的地震波形数据,由频时分析方法提取了Love波相速度频散曲线,经过反演得到了研究区内的Love波相速度分布.根据Love波纯路径频散,采用线性反演方法对0.25°×0.25°的网格点进行了一维S波速度结构反演,利用线性插值获取了南北地震带地区的三维S波速度结构.结果显示了松潘-甘孜地体和川滇菱形块体地区的下地壳具有明显的S波低速层分布,该异常分布特征支持解释青藏高原隆升及其地壳物质运移的下地壳流模型.在100至120 km深度上,川滇菱形块体西北部呈现较强的S波高速异常,这可能是印度岩石圈板块沿喜马拉雅东构造结下插至该区域所致,该区域下地壳的低速软弱物质与上地幔的高速强硬物质形成了鲜明对比,暗示了地壳和上地幔可能具有不同的构造运动和变形方式,这为该区域的壳幔动力学解耦提供了条件. 相似文献
13.
使用位于松辽盆地内部的NECESSArray台阵连续两年背景噪声数据,通过波形互相关和多重滤波方法提取到2~14 s较短周期的Rayleigh波群速度和相速度频散曲线,基于快速行进(FMM)面波成像方法得到群速度和相速度成像结果,并采用最小二乘迭代线性方法反演获得了松辽盆地深至12 km的三维S波速度结构.本文成像结果显示:松辽盆地内部S波速度分布的横向不均匀性与该区域的构造单元呈现出良好的空间对应关系.从地表至下方的6 km深度,盆地北部比南部表现出更加强烈的低速异常,这一特征可能与盆地南北的沉积构造差异有关.中央坳陷区低速异常的边界与嫩江断裂走向相互平行,表明盆地基底断裂对盆地形成演化具有一定的控制作用.在垂直速度结构剖面中,2.9 km·s-1的S波速度等值线与地震反射剖面显示的盆地基底深度大致对应.基于S波速度模型和盆地基底速度(2.9 km·s-1),我们获得精细的松辽盆地沉积层厚度模型,结果表明松辽盆地的沉积层厚度分布呈现出中间厚、四周薄的特征,中央坳陷区的沉积层厚度范围大约在3~6 km. 相似文献
14.
浅层地震反射波法和面波方法是两种相互独立发展的地震勘探方法,在各自的数据采集和处理中,对方都是作为干扰信号而存在. 本文利用浅层地震反射资料中被视为干扰的面波信号,通过成熟的多道面波勘探技术处理浅层地震反射资料,在频率-波数域中提取多阶振型面波的频散曲线,并基于该曲线反演浅地表S波速度结构. 这种方法充分开发利用了已有数据,无需单独的面波数据采集系统,同时为解释浅层地震反射资料提供了额外的信息约束. 结果表明:浅层地震反射资料中可提取出可靠的多阶振型面波频散曲线,并能给出稳定的反演结果,同时,面波反演的多解性可以通过高阶振型反演得以进一步约束;低速层的存在是观测频散曲线出现振型跳跃或呈“之”字形回折的必要条件而非充分条件. 相似文献
15.
利用面波频散曲线反演地下介质的S波速度结构, 是浅层工程地震领域一种重要的方法技术.传统的面波法包括主被动源的面波多道分析方法(MASW)和被动源的空间自相关(SPAC)方法, 均需要多台地震仪同时记录地面振动; 而记录平动和旋转运动的单台站六分量地震数据理论上也可以获得面波频散曲线.本文以河北唐山城区煤矿采空区浅层工程勘探实际六分量地震数据为例, 对比了利用单台站六分量地震数据与主、被动源法多台站提取的Rayleigh波频散曲线.试验结果表明利用纵波扫描可控震源时, 30 Hz以下频段利用单台站六分量地震数据提取的基阶Rayleigh波频散曲线与主、被动源MASW方法提取的频散曲线结果一致, 说明在浅层工程地震勘查中, 利用单物理点的六分量地震观测反演浅层横波速度是可行的. 相似文献
16.
在近地表地球物理领域, 基于地脉动(或称背景噪声)提取的面波频散曲线反演地下S波速度结构是一种简单经济的工程勘察方法. 本文基于地脉动的空间自相关方法对一个微型台阵观测的背景噪声记录进行处理, 介绍了一种简单易行的提取频散曲线的数据处理方法, 获得了6.7—23 Hz频段的可靠频散曲线; 通过对该观测频散曲线与预测模型的频散曲线进行拟合, 反演得到S波速度结构. 结果表明, 该速度结构与钻孔直接测试的结果相吻合. 相似文献
17.
高分辨率的面波频散谱成像是浅层地震勘探领域基于频散性质反演横波速度结构中的一个关键步骤.在天然地震探测领域,仅利用两个台站记录的线性信号比较法(LSC),被广泛用来计算面波的频散谱,并用于大尺度的面波层析成像.然而互相关的成像方式会造成频散谱在低频端较低的分辨率.非线性信号比较法(NLSC)利用指数函数克服了这个问题,... 相似文献
18.
S波速度结构能够反映地球介质的物性差异,是地壳内低速区结构特征判别的重要依据.本文尝试利用空间自相关法(SPAC法)从地震台站微动信号的垂直分量中提取瑞利波相速度频散曲线,通过对频散曲线的反演获得地下介质的S波速度结构.以国家数字测震台网8个宽频带地震台站的实测微动数据为例,采用SPAC方法获得了首都圈地区北京附近约30 km 深度范围内的一维S波速度结构.结果表明,该区结晶基底埋深较浅约2 km;分别在5~8 km 和12~16 km 深处发育S波低速层;8 km 和 20 km 处是S波速度差异较大的速度分界面.这一结果与以往地震学及人工地震探测结果较为吻合,表明SPAC法估算地壳S波速度结构是可行、有效的. 相似文献
19.
公式推导和数值实验都表明远震接收函数直达波幅度对近地表S波速度比较敏感,可以用于确定近地表(如沉积层)的S波速度值.本文利用该方法分析了青藏高原东北缘区域数字地震台网36个台站的远震资料,得到了研究区近地表S波速度分布特征.研究结果表明:在深度5±2.5 km范围内,祁连山—河西走廊区域近地表S波速度均值较小;位于地形梯度带的甘东南区域近地表S波速度呈现较为复杂的分布.通过与该区域沉积层厚度结果对比,发现近地表S波速度与沉积层厚度呈现较好的负相关.本研究是对目前接收函数方法的有效补充,在探测研究近地表速度结构方面,相比人工地震方法其成本几乎可忽略且环保.在目前地震波观测数据海量增长的背景下,该方法对于确定不同区域近地表结构具有较大潜力. 相似文献
20.
Local S-wave velocity-depth profiles are a key factor in seismic hazard assessment, as they allow the amplification potential
of the sedimentary cover to be evaluated. Ambient seismic noise is mainly composed of surface waves, and therefore contains
vital information about the S-wave velocity structure, allowing polarization or dispersion curves to be obtained from single
station or array noise recordings. At two sites in the area of Cologne, Germany, the extended spatial correlation method was
applied to such recordings and apparent phase velocity curves in the frequency range of interest for earthquake engineering
were obtained. Using this data, a linearized inversion, the simplex downhill method, and a genetic algorithm yielded similar
S-wave profiles. However, the latter method is recommended since it is less dependent upon a good starting model. Importantly,
the presence of low-velocity layers in the Cologne area made it necessary to consider in the frequency range of interest higher
modes in the inversion procedures. Finally, independent information on the total thickness of the sedimentary cover permitted
the estimation of a 2D S-wave velocity profile crossing the Cologne area. Here, the H/V ratio inversion using 20 single-station
noise recordings was used, with the results in good agreement with a geological profile. 相似文献
|