Temporal variation and the effect of rainfall on metals flux from the historic Beatson mine,Prince William Sound,Alaska, USA

Several abandoned Cu mines are located along the shore of Prince William Sound, AK, where the effect of mining-related discharge upon shoreline ecosystems is unknown. To determine the magnitude of this effect at the former Beatson mine, the largest Cu mine in the region and a Besshi-type massive sulfide ore deposit, trace metal concentration and flux were measured in surface run-off from remnant, mineralized workings and waste. Samples were collected from seepage waters; a remnant glory hole which is now a pit lake; a braided stream draining an area of mineralized rock, underground mine workings, and waste piles; and a background location upstream of the mine workings and mineralized rock. In the background stream pH averaged ∼7.3, specific conductivity (SC) was ∼40 μS/cm, and the aqueous components indicative of sulfide mineral weathering, SO₄ and trace metals, were at detection limits or lower. In the braided stream below the mine workings and waste piles, pH usually varied from 6.7 to 7.1, SC varied from 40 to 120 μS/cm, SO₄ had maximum concentrations of 32 mg/L, and the trace metals Cu, Ni, Pb, and Zn showed maximum total acid extractable concentrations of 186, 5.9, 6.2 and 343 μg/L, respectively.     

Metal extractability in acidic and neutral mine tailings from the Cartagena-La Unión Mining District (SE Spain)

Mine tailings are ubiquitous in the landscapes of mined areas. Metal solubilities were compared in two chemically distinct mine tailings from the old Mining District of Cartagena-La Unión (SE Spain). One of the tailings was acidic (pH 3.0) with 5400 mg/kg Zn, 1900 mg/kg As and 7000 mg/kg Pb. The other was neutral (pH 7.4) with 9100 mg/kg Zn, 5200 mg/kg Pb and 350 mg/kg As. In samples from the acidic tailings, more than 15% of the Zn and 55% of the Cd were extractable with 0.1 M NaNO₃, and distilled water. In the neutral tailings, using the same reagents, less than 1% of the metals were extractable. A sequential extraction procedure revealed that the sum of the residual and the Fe oxide fractions of Cu, Zn and Pb comprised 80–95% in the acidic tailings and 70–90% in the neutral tailings. The acidic mine tailings had a higher metal solubility, resulting in more metal leaching in the short-term, but also a higher fraction of inert metal. In contrast, in the neutral tailings, the metals were evenly distributed between, oxides and the residual fraction. This implies lower metal mobility in the short-term, but that metal mobility may increase in the long-term. When applied to mine tailings, sequential extractions may provide misleading results because the strong cation exchange capacity of some extractants may induce pH changes and thereby significantly change metal solubility.     

Assessing the concentration,speciation, and toxicity of dissolved metals during mixing of acid-mine drainage and ambient river water downstream of the Elizabeth Copper Mine,Vermont, USA

The authors determine the composition of a river that is impacted by acid-mine drainage, evaluate dominant physical and geochemical processes controlling the composition, and assess dissolved metal speciation and toxicity using a combination of laboratory, field and modeling studies. Values of pH increase from 3.3 to 7.6 and the sum of dissolved base metal (Cd + Co + Cu + Ni + Pb + Zn) concentrations decreases from 6270 to 100 μg/L in the dynamic mixing and reaction zone that is downstream of the river’s confluence with acid-mine drainage. Mixing diagrams and PHREEQC calculations indicate that mixing and dilution affect the concentrations of all dissolved elements in the reach, and are the dominant processes controlling dissolved Ca, K, Li, Mn and SO₄ concentrations. Additionally, dissolved Al and Fe concentrations decrease due to mineral precipitation (gibbsite, schwertmannite and ferrihydrite), whereas dissolved concentrations of Cd, Co, Cu, Ni, Pb and Zn decrease due to adsorption onto newly formed Fe precipitates.     

Mineralogy and the release of trace elements from slag from the Hegeler Zinc smelter,Illinois (USA)

Slag from the former Hegeler Zn-smelting facility in Illinois (USA) is mainly composed of spinifex Ca-rich plagioclase, fine-grained dendritic or coarse-grained subhedral to anhedral clinopyroxenes, euhedral to subhedral spinels, spherical blebs of Fe sulfides, silicate glass, and less commonly fayalitic olivine. Mullite and quartz were also identified in one sample as representing remnants of the furnace lining. Secondary phases such as goethite, hematite and gypsum are significant in some samples and reflect surficial weathering of the dump piles or represent byproducts of roasting. A relatively rare Zn-rich material contains anhedral willemite, subhedral gahnite, massive zincite, hardystonite and a Zn sulfate (brianyoungite), among other phases, and likely represents the molten content of the smelting furnace before Zn extraction. The bulk major-element chemistry of most slag samples is dominated by SiO₂, Al₂O₃, Fe₂O₃ and CaO. The bulk composition of the slag suggests a high viscosity of the melt and the mineralogy suggests a high silica content of the melt. Bulk slag trace-element chemistry shows that the dominant metal is Zn with >28.4 wt.% in the Zn-rich material and between 212 and 14,900 mg/kg in the other slags. The concentrations of other trace elements reach the following: 45 mg/kg As, 1170 mg/kg Ba, 191 mg/kg Cd, 242 mg/kg Co, 103 mg/kg Cr, 6360 mg/kg Cu, 107 mg/kg Ni, and 711 mg/kg Pb.     

Field application of calcite Dispersed Alkaline Substrate (calcite-DAS) for passive treatment of acid mine drainage with high Al and metal concentrations

Passive treatment systems are widely used for remediation of acid mine drainage (AMD), but existing designs are prone to clogging or loss of reactivity due to Al- and Fe-precipitates when treating water with high Al and heavy metal concentrations. Dispersed alkaline substrate (DAS) mixed from a fine-grained alkaline reagent (e.g. calcite sand) and a coarse inert matrix (e.g. wood chips) had shown high reactivity and good hydraulic properties in previous laboratory column tests. In the present study, DAS was tested at pilot field scale in the Iberian Pyrite Belt (SW Spain) on metal mine drainage with pH near 3.3, net acidity 1400–1650 mg/L as CaCO₃, and mean concentrations of 317 mg/L Fe (95% Fe(II)), 311 mg/L Zn, 74 mg/L Al, 20 mg/L Mn, and 1.5–0.1 mg/L Cu, Co, Ni, Cd, As and Pb. The DAS-tank removed an average of 870 mg/L net acidity as CaCO₃ (56% of inflow), 25% Fe, 93% Al, 5% Zn, 95% Cu, 99% As, 98% Pb, and 14% Cd, but no Mn, Ni or Co. Average gross drain pipe alkalinity was 181 mg/L as CaCO₃, which increased total Fe removal to 153 mg/L (48%) in subsequent sedimentation ponds. Unfortunately, the tank suffered clogging problems due to the formation of a hardpan of Al-rich precipitates. DAS lifetime could probably be increased by lowering Al-loads.     

Hydrological and geochemical control of metals and arsenic in a Mediterranean river contaminated by acid mine drainage (the Amous River,France); preliminary assessment of impacts on fish (Leuciscus cephalus)

Dissolved and particulate concentrations of metals (Fe, Al, Mn, Co, Ni, Cu, Zn, Cd, Tl, Pb) and As were monitored over a 5 year period in the Amous River downstream of its confluence with a creek severely affected by acid mine drainage (AMD) originating from a former Pb–Zn mine. Water pH ranged from 6.5 to 8.8. Metals were predominantly in dissolved form, except Fe and Pb, which were in particulate form. In the particulate phase, metals were generally associated with Al oxides, whereas As was linked to Fe oxides. Metal concentrations in the dissolved and/or particulate phase were generally higher during the wet season due to higher generation of AMD. Average dissolved (size < 0.22 μm) metal concentrations (μg/L) were 1 ± 4 (Fe), 69 ± 49 (Al), 140 ± 118 (Mn), 4 ± 3 Co, 6 ± 4 (Ni), 1.3 ± 0.8 (Cu), 126 ± 81 (Zn), 1.1 ± 0.7 (Cd), 0.9 ± 0.5 (Tl), 2 ± 3 (Pb). Dissolved As concentrations ranged from 5 to 134 μg/L (30 ± 23 μg/L). During the survey, the concentration of colloidal metals (5 kDa < size < 0.22 μm) was less than 25% of dissolved concentrations. Dissolved metal concentrations were generally higher than the maximum concentrations allowed in European surface waters for priority substances (Ni, Cd and Pb) and higher than the environmental quality standards for other compounds. Using Diffusion Gradient in Thin Film (DGT) probes, metals were shown to be in potentially bioavailable form. The concentrations in Leuciscus cephalus were below the maximum Pb and Cd concentrations allowed in fish muscle for human consumption by the European Water Directive. Amongst the elements studied, only As, Pb and Tl were shown to bioaccumulate in liver tissue (As, Pb) or otoliths (Tl). Bioaccumulation of metals or As was not detected in muscle.     

Iron,manganese and trace metal concentrations in seaweeds from the central west coast of the Gulf of California

Concentrations of Co, Cu, Fe, Mn, Ni, Pb and Zn in four macroalgae species (Ulva lactuca, Chondracanthus squarrulosus, Sargassum sinicola and Gracilariopsis lemaneiformis) were obtained for the first time from the central part of the west coast of the Gulf of California. Generally, no differences in metal concentrations were found among the different seaweed species, although spatial differences were apparent. Iron, Mn and Cu exhibited higher concentrations at the stations located in front of Angel de la Guarda Island, probably because of high vertical mixing processes present in the zone. The results were compared with dissolved metal concentrations reported for the Gulf of California (Cd, Mn and Fe) and the North Pacific Ocean. The resulting linear regression of the results vs. North Pacific Ocean concentrations indicated that the levels of Cu, Ni and Zn measured in this study were within its 95% confidence level. Furthermore, this comparison was capable of detecting dissolved Fe and Mn enrichments in Gulf of California waters relative to the North Pacific Ocean concentrations. Calculations of total masses of metals associated with algal biomass on the west coast of the Gulf of California indicated that the lowest masses were represented by Cu (108 ± 25 kg) and Ni (184 ± 52 kg), whereas Pb (1.1 ± 0.6 ton) and Fe (10.9 ± 8.5 ton) were the elements with the highest associated masses.     

Geochemical processes and mobilization of toxic metals and metalloids in an As-rich base metal waste pile in Zimapán,Central Mexico

The geochemistry and mineralogy of samples collected along depth profiles from an As-rich tailing deposit with abundant calcite was studied to determine the processes that influence the mobility of Fe, Zn, Cu, Ni, Cd, As, Sb, Cr and Tl. In spite of their near neutral pH, almost all of them are acid potential generators. Total concentrations decreased as: Fe > As > Zn > Pb > Cu > Sb > Cd > Cr > Ni > Tl. Soluble contents were lower and followed a slightly different order. Mobility decreased as: Tl > Cd, Zn, Cu, Sb, Ni, As > Fe, Pb > Cr. Higher soluble concentrations of Fe, Cu, Zn, As, Pb, and Ni were found in low-pH samples and of Sb and Tl in near-neutral samples. Sulfide oxidation processes are developing in the tailing’s dam. These processes do not have a trend with depth but occur mainly in acid layers. Near neutral layers formed by primary sulfides and calcite probably correspond to wastes produced from the processing of ore coming mainly from pods within the skarn, and acid layers with abundant secondary minerals from material mined from chimneys and mantos. The presence of calcite influences speciation, neutralizes acid mine drainage (AMD), and decreases the mobility of most toxic metals and metalloids (TMMs). However, a hard-pan layer was not observed in the studied profiles. Retention of TMM within tailings probably occurs through the formation of low solubility metal carbonates and from elevation of pH that promotes Fe hydroxides precipitation that may retain As, Sb and metals. Calcite occurrence promotes As, Cd, Cu, Fe, Zn, Pb, Cd and Cr retention, does not play a role on Tl and Ni mobilization, and increases Sb release.     

Sulfide oxidation and distribution of metals near abandoned copper mines in coastal environments,Prince William Sound,Alaska, USA

The oxidation of sulfide-rich rocks, mostly leftover debris from Cu mining in the early 20th century, is contributing to metal contamination of local coastal environments in Prince William Sound, Alaska. Analyses of sulfide, water, sediment, precipitate and biological samples from the Beatson, Ellamar, and Threeman mine sites show that acidic surface waters generated from sulfide weathering are pathways for redistribution of environmentally important elements into and beyond the intertidal zone at each site. Volcanogenic massive sulfide deposits composed of pyrrhotite and (or) pyrite + chalcopyrite + sphalerite with subordinate galena, arsenopyrite, and cobaltite represent potent sources of Cu, Zn, Pb, As, Co, Cd, and Hg. The resistance to oxidation among the major sulfides increases in the order pyrrhotite ? sphalerite < chalcopyrite ? pyrite; thus, pyrrhotite-rich rocks are typically more oxidized than those dominated by pyrite. The pervasive alteration of pyrrhotite begins with rim replacement by marcasite followed by replacement of the core by sulfur, Fe sulfate, and Fe–Al sulfate. The oxi dation of chalcopyrite and pyrite involves an encroachment by colloform Fe oxyhydroxides at grain margins and along crosscutting cracks that gradually consumes the entire grain. The complete oxidation of sulfide-rich samples results in a porous aggregate of goethite, lepidocrocite and amorphous Fe-oxyhydroxide enclosing hydrothermal and sedimentary silicates. An inverse correlation between pH and metal concentrations is evident in water data from all three sites. Among all waters sampled, pore waters from Ellamar beach gravels have the lowest pH (∼3) and highest concentrations of base metals (to ∼25,000 μg/L), which result from oxidation of abundant sulfide-rich debris in the sediment. High levels of dissolved Hg (to 4100 ng/L) in the pore waters probably result from oxidation of sphalerite-rich rocks. The low-pH and high concentrations of dissolved Fe, Al, and SO₄ are conducive to precipitation of interstitial jarosite in the intertidal gravels. Although pore waters from the intertidal zone at the Threeman mine site have circumneutral pH values, small amounts of dissolved Fe²⁺ in the pore waters are oxidized during mixing with seawater, resulting in precipitation of Fe-oxyhydroxide flocs along the beach–seawater interface. At the Beatson site, surface waters funneled through the underground mine workings and discharged across the waste dumps have near-neutral pH (6.7–7.3) and a relatively small base-metal load; however, these streams probably play a role in the physical transport of metalliferous particulates into intertidal and offshore areas during storm events. Somewhat more acidic fluids, to pH 5.3, occur in stagnant seeps and small streams emerging from the Beatson waste dumps. Amorphous Fe precipitates in stagnant waters at Beatson have high Cu (5.2 wt%) and Zn (2.3 wt%) concentrations that probably reflect adsorption onto the extremely high surface area of colloidal particles. Conversely, crystalline precipitates composed of ferrihydrite and schwertmannite that formed in the active flow of small streams have lower metal contents, which are attributed to their smaller surface area and, therefore, fewer reactive sorption sites. Seeps containing precipitates with high metal contents may contribute contaminants to the marine environment during storm-induced periods of high runoff. Preliminary chemical data for mussels (Mytilus edulis) collected from Beatson, Ellamar, and Threeman indicate that bioaccumulation of base metals is occurring in the marine environment at all three sites.     

Computer simulations of the interactions of the (0 1 2) and (0 0 1) surfaces of jarosite with Al, Cd, Cu and Zn

Jarosite is an important mineral on Earth, and possibly on Mars, where it controls the mobility of iron, sulfate and potentially toxic metals. Atomistic simulations have been used to study the incorporation of Al³⁺, and the M²⁺ impurities Cd, Cu and Zn, in the (0 1 2) and (0 0 1) surfaces of jarosite. The calculations show that the incorporation of Al on an Fe site is favorable on all surfaces in which terminal Fe ions are exposed, and especially on the (0 0 1) [Fe₃(OH)₃]⁶⁺ surface. Incorporation of Cd, Cu or Zn on a K site balanced by a K vacancy is predicted to stabilize the surfaces, but calculated endothermic solution energies and the high degree of distortion of the surfaces following incorporation suggest that these substitutions will be limited. The calculations also suggest that incorporation of Cd, Cu and Zn on an Fe site balanced by an OH vacancy, or by coupled substitution on both K and Fe sites, is unfavorable, although this might be compensated for by growth of a new layer of jarosite or goethite, as predicted for bulk jarosite. The results of the simulations show that surface structure will exert an influence on uptake of impurities in the order Cu > Cd > Zn, with the most favorable surfaces for incorporation being (0 1 2) [KFe(OH)₄]⁰ and (0 0 1) [Fe₃(OH)₃]⁶⁺.     

Arsenic mobility in mildly alkaline drainage from an orogenic lode gold deposit,Bralorne mine,British Columbia

The historical (1932–1971) Bralorne mine produced over 87 million grams of Au from an archetypal orogenic lode gold deposit in southwest British Columbia. High concentrations of As in mine drainage, however, represent an on-going environmental concern prompting a detailed study of effluent chemistry. The discharge rate at the mine portal was monitored continuously over a fourteen-month period during which effluent samples were collected on a quasi-weekly basis. Water samples were also collected on synoptic surveys of the adit between the portal and the main source of flow in the flooded workings. Total concentrations of As in the mildly alkaline (pH = 8.7) portal drainage average 3034 μg/L whereas at the source they average 5898 μg/L. As emergent waters from the flooded workings flow toward the portal, their dissolved oxygen content and pH increase from 0 to 10 mg/L and from 7.7 to 9, respectively. Near the emergence point, dissolved Fe precipitates rapidly, sorbing both As(III) and As(V). With increasing distance from the emergence point, dissolved As(III) concentrations drop to detection limits through sorption on hydrous ferric oxide and through oxidation to As(V). Concentrations of dissolved As(V), on the other hand, increase and stabilize, reflecting lower sorption at higher pH and the lack of available sorbent. Nonetheless, based on synoptic surveys, approximately 35% of the source As load is sequestered in the adit resulting in As sediment concentrations averaging 8.5 wt%. The remaining average As load of 1.34 kg/d is discharged from the portal. Partitioning of As(V) between dissolved and particulate phases in portal effluent is characterized by a sorption density of 0.37 mol As (mol Fe)⁻¹ and by a distribution coefficient (K_d) of 130 L/g HFO. The relatively high sorption density may reflect co-precipitation of As with Fe oxyhydroxides rather than a purely adsorption-controlled process. Results of this study show that the As self-mitigating capacity of drainage from orogenic lode gold deposits may be poor in high-pH and Fe-limited settings.     

Behavior of metals (Cu,Zn and Cd) in the initial stage of water system contamination: Effect of pH and suspended particles

The fate of potentially harmful metals (PHM) after their entry into an unpolluted fresh water body depends on the physicochemical and biological parameters of the aquatic ecosystem. This paper considers the effect of pH and suspended particles (SP) on the behavior of Cu, Zn and Cd when they enter a fresh water reservoir. In a field experiment, four mesocosms were constructed in the Novosibirskoye Reservoir to allow systematic variation of SP concentration (15 or 250 mg/L) and pH (8.5 or 6.5). The initial concentrations of Cu, Zn and Cd in the mesocosms were 1000, 1000 and 200 μg/L, respectively. Natural bottom sediments were used to provide additional mineral SP, and water hyacinth was used as a floating plant species. Over 11 days, measurements were made of several indicators: residual metal concentration in solution ([PHM]_w); metal concentration in SP ([PHM]_s); primary productivity of the phytoplankton community; mass of settled SP; PHM concentration in settled SP; and PHM bioaccumulation by water hyacinth. The ratio [PHM]_w/[PHM]_s in the water varied in the order Cu < Zn < Cd and was higher at pH 6.5 than at pH 8.5. This observation reflects different PHM sorption (Cu > Zn > Cd) onto mineral SP and PHM biosorption by planktonic organisms. Phytoplankton acts as a renewable source of organic SP and plays an important role in metal removal from the water in the mesocosms. After 11 days the residual concentrations of Cu, Zn and Cd in the mesocosm without SP addition (initial SP concentration was 15 mg/L) were 272, 355 and 84 μg/L, respectively. The residual concentrations of Cu, Zn and Cd in mesocosms with SP addition were 57, 100 and 14 μg/L at pH 8.5 and 80, 172 and 20 μg/L at pH 6.5, respectively. Therefore, addition of SP resulted in faster and more complete removal of metals into the bottom sediments. Floating plants (water hyacinth) accumulated PHM (Cu > Zn > Cd) more effectively at pH 8.5 than at pH 6.5, and PHM concentrations in the roots were higher than in settling SP. The general trends of PHM removal from contaminated water via sedimentation and bioaccumulation are compared with changes of metal speciation in solution.     

Contamination of surface waters by mining wastes in the Milluni Valley (Cordillera Real,Bolivia): Mineralogical and hydrological influences

This study is one of very few dealing with mining waste contamination in high altitude, tropical-latitude areas exploited during the last century. Geochemical, mineralogical and hydrological characterizations of potentially harmful elements (PHEs) in surface waters and sediments were performed in the Milluni Valley (main reservoir of water supply of La Paz, Bolivia, 4000 m a.s.l.), throughout different seasons during 2002–2004 to identify contamination sources and sinks, and contamination control parameters. PHE concentrations greatly exceeded the World Health Organization water guidelines for human consumption. The very acidic conditions, which resulted from the oxidation of sulfide minerals in mining waste, favoured the enrichment of dissolved PHEs (Cd > Zn ? As ? Cu ∼ Ni > Pb > Sn) in surface waters downstream from the mine. Stream and lake sediments, mining waste and bedrock showed the highest PHE content in the mining area. With the exception of Fe, the PHEs were derived from specific minerals (Fe, pyrite; Zn, Cd, sphalerite, As, Fe, arsenopyrite, Cu, Fe, chalcopyrite, Pb, galena, Sn, cassiterite), but the mining was responsible for PHEs availability. Most of the PHEs were extremely mobile (As > Fe > Pb > Cd > Zn ∼ Cu > Sn) in the mining wastes and the sediments downstream from the mine. pH and oxyhydroxides mainly explained the contrasted availability of Zn (mostly in labile fractions) and As (associated with Fe-oxyhydroxides). Unexpectedly, Pb, Zn, As, and Fe were significantly attenuated by organic matter in acidic lake sediments.     

Geochemical and equilibrium trends in mine pit lakes

Chemical composition and equilibrium trends in mine pit lakes were examined to provide guidance for the application of geochemical models in predicting future lake water quality at prospective open pit mines. Composition trends show that elevated solute levels generally occur only at the extremes of acidic and alkaline pH conditions. Concentrations of cationic metals (Al, Cd, Cu, Fe, Mn, Pb, and Zn) are elevated only in acidic pit lakes, whereas anionic metalloids (As and Se) are generally elevated only in alkaline pit lakes. These trends are indicative of sulfide mineral oxidation and evapoconcentration for acidic and alkaline conditions, respectively.For nearly all pit lakes, SO₄ is the dominant solute, but is limited by gypsum solubility. Fluorite, calcite, and barite are also important solubility controls. Well-defined solubility controls exist for the major metals (Al, Fe, Mn), including jurbanite and alunite for Al, ferrihydrite for Fe, and manganite, birnessite, and, possibly, rhodochrosite for Mn. Determinations of definite controls for the minor metals are less distinct, but may include otavite for Cd, brochantite and malachite for Cu, cerrusite and pyromorphite for Pb, and hydrozincite and Zn silicates for Zn. Concentrations of As and Se appear to be limited only by adsorption, but this control is sharply diminished by increased pH and SO₄ concentration. In general, the concentrations of minor metals in pit lakes are not well represented by the theoretical solubilities of pure-phase minerals contained in the thermodynamic databases. Hence, modeling efforts will generally have to rely on empirical data on the leaching characteristics of pit wall-rocks to predict the concentrations of minor metals (Cd, Cu, Pb, Zn) in mine pit lakes.Methodologies for predicting pit lake water chemistry are still evolving. Geochemical and equilibrium trends in existing pit lakes can provide valuable information for guiding the development and application of predictive models. However, mineralogical studies of pit lake sediments, suspended particles, and alteration assemblages and studies of redox transformations are still needed to validate and refine the representations of geochemical processes in water quality models of mine pit lakes.     

Geochemistry of highly acidic mine water following disposal into a natural lake with carbonate bedrock

Acid mine drainage (AMD) from the Zn–Pb(–Ag–Bi–Cu) deposit of Cerro de Pasco (Central Peru) and waste water from a Cu-extraction plant has been discharged since 1981 into Lake Yanamate, a natural lake with carbonate bedrock. The lake has developed a highly acidic pH of ∼1. Mean lake water chemistry was characterized by 16,775 mg/L acidity as CaCO₃, 4330 mg/L Fe and 29,250 mg/L SO₄. Mean trace element concentrations were 86.8 mg/L Cu, 493 mg/L Zn, 2.9 mg/L Pb and 48 mg/L As, which did not differ greatly from the discharged AMD. Most elements showed increasing concentrations from the surface to the lake bottom at a maximal depth of 41 m (e.g. from 3581 to 5433 mg/L Fe and 25,609 to 35,959 mg/L SO₄). The variations in the H and O isotope compositions and the element concentrations within the upper 10 m of the water column suggest mixing with recently discharged AMD, shallow groundwater and precipitation waters. Below 15 m a stagnant zone had developed. Gypsum (saturation index, SI ∼ 0.25) and anglesite (SI ∼ 0.1) were in equilibrium with lake water. Jarosite was oversaturated (SI ∼ 1.7) in the upper part of the water column, resulting in downward settling and re-dissolution in the lower part of the water column (SI ∼ −0.7). Accordingly, jarosite was only found in sediments from less than 7 m water depth. At the lake bottom, a layer of gel-like material (∼90 wt.% water) of pH ∼1 with a total organic C content of up to 4.40 wet wt.% originated from the kerosene discharge of the Cu-extraction plant and had contaminant element concentrations similar to the lake water. Below the organic layer followed a layer of gypsum with pH 1.5, which overlaid the dissolving carbonate sediments of pH 5.3–7. In these two layers the contaminant elements were enriched compared to lake water in the sequence As < Pb ≈ Cu < Cd < Zn = Mn with increasing depth. This sequence of enrichment was explained by the following processes: (i) adsorption of As on Fe-hydroxides coating plant roots at low pH (up to 3326 mg/kg As), (ii) adsorption at increasing pH near the gypsum/calcite boundary (up to 1812 mg/kg Pb, 2531 mg/kg Cu, and 36 mg/kg Cd), and (iii) precipitation of carbonates (up to 5177 mg/kg Zn and 810 mg/kg Mn; all data corrected to a wet base). The infiltration rate was approximately equal to the discharge rate, thus gypsum and hydroxide precipitation had not resulted in complete clogging of the lake bedrocks.     

Uptake of Zn,Cu, Pb,and Cd by water hyacinth in the initial stage of water system remediation

The removal efficiency of water hyacinth for Zn, Cu, Pb and Cd after their entry into an undisturbed fresh water body was studied using minicosms placed within a reservoir. Variable parameters were water pH (6 or 8), single or multi-metal additions, and the plant biomass. The initial concentrations of Zn, Cu, Pb and Cd in water (500, 250, 250 and 50 μg/L, respectively) quickly decreased in the order Pb ≈ Cu ? Cd ≈ Zn in the first days. Metal removal was more efficient at pH 8 than at pH 6, and it was only slightly higher for single metals compared to multi-metal additions. After 8 days the remaining amounts of metals relative to their initial concentrations for multi-metal pollution treatments were 8% and 24% (Cu), 11% and 26% (Pb), 24% and 50% (Cd), and 18% and 57% (Zn) at pH 8 and pH 6, respectively. Increasing plant biomass promoted faster metal removal. The bioconcentration factor (the ratio of the metal concentration in whole plants to the initial metal concentration in water) exceeds 2000 for all metals (with the exception of Zn and Cd at pH 6). It was concluded that the water hyacinth can be successfully used for fast removal of metals in the initial stage of water body remediation.     

Distribution of Cu,Co, As,and Fe in mine waste,sediment, soil,and water in and around mineral deposits and mines of the Idaho Cobalt Belt,USA

The distribution of Cu, Co, As and Fe was studied downstream from mines and deposits in the Idaho Cobalt Belt (ICB), the largest Co resource in the USA. To evaluate potential contamination in ecosystems in the ICB, mine waste, stream sediment, soil, and water were collected and analyzed for Cu, Co, As and Fe in this area. Concentrations of Cu in mine waste and stream sediment collected proximal to mines in the ICB ranged from 390 to 19,000 μg/g, exceeding the USEPA target clean-up level and the probable effect concentration (PEC) for Cu of 149 μg/g in sediment; PEC is the concentration above which harmful effects are likely in sediment dwelling organisms. In addition concentrations of Cu in mine runoff and stream water collected proximal to mines were highly elevated in the ICB and exceeded the USEPA chronic criterion for aquatic organisms of 6.3 μg/L (at a water hardness of 50 mg/L) and an LC50 concentration for rainbow trout of 14 μg/L for Cu in water. Concentrations of Co in mine waste and stream sediment collected proximal to mines varied from 14 to 7400 μg/g and were highly elevated above regional background concentrations, and generally exceeded the USEPA target clean-up level of 80 μg/g for Co in sediment. Concentrations of Co in water were as high as in 75,000 μg/L in the ICB, exceeding an LC50 of 346 μg/L for rainbow trout for Co in water by as much as two orders of magnitude, likely indicating an adverse effect on trout. Mine waste and stream sediment collected in the ICB also contained highly elevated As concentrations that varied from 26 to 17,000 μg/g, most of which exceeded the PEC of 33 μg/g and the USEPA target clean-up level of 35 μg/g for As in sediment. Conversely, most water samples had As concentrations that were below the 150 μg/L chronic criterion for protection of aquatic organisms and the USEPA target clean-up level of 14 μg/L. There is abundant Fe oxide in streams in the ICB and several samples of mine runoff and stream water exceeded the chronic criterion for protection of aquatic organisms of 1000 μg/L for Fe. There has been extensive remediation of mined areas in the ICB, but because some mine waste remaining in the area contains highly elevated Cu, Co, As and Fe, inhalation or ingestion of mine waste particulates may lead to human exposure to these elements.     

Field multi-step limestone and MgO passive system to treat acid mine drainage with high metal concentrations

Passive treatment systems have become one of the most sustainable and feasible ways of remediating acid mine drainage (AMD). However, conventional treatments show early clogging of the porosity or/and coating of the reactive grains when high acidity and metal concentrations are treated. The performance of fine-grained reagents dispersed in a high porosity matrix of wood shavings was tested as an alternative to overcome these durability problems. The system consisted of two tanks of 3 m³ filled with limestone sand and wood shavings, and one tank of 1 m³ with caustic magnesia powder and wood shavings, separated by several oxidation cascades and decantation ponds. The system treated about 1.5 m³/day of AMD containing an average of 360 mg/L Fe, 120 mg/L Al, 390 mg/L Zn, 10 mg/L Cu, 300 μg/L As and 140 μg/L Pb, a mean pH of 3.08 and a net acidity of 2500 mg/L as CaCO₃ equivalent. The water reached pH 5 and 6 in the first and second limestone tanks, respectively (suitable to remove trivalent metals); and pH 8–9 in the MgO tank (suitable to remove divalent metals). After 9 months of operation, the system achieved an average removal of 100% Al, Cu, As, Pb, more than 70% Fe, about 25% Zn and 80% acidity. Goethite, schwertmannite, hydrobasaluminite, amorphous Al(OH)₃ and gypsum were the main precipitates in the two limestone tanks. Precipitation of divalent metals (Fe (II), Zn, and traces of Cd, Ni and Co) were complete inside the third tank of MgO, but preferential flow along the walls was responsible for its low treatment performance. Goethite, gypsum, Zn-schulenbergite and sauconite are the crystalline solid phases identified in the MgO tank.     

Transport and sediment–water partitioning of trace metals in acid mine drainage: an example from the abandoned Kwangyang Au–Ag mine area, South Korea

Transport and sediment–water partitioning of trace metals (Cr, Co, Fe, Pb, Cu, Ni, Zn, Cd) in acid mine drainage were studied in two creeks in the Kwangyang Au–Ag mine area, southern part of Korea. Chemical analysis of stream waters and the weak acid (0.1 N HCl) extraction, strong acid (HF–HNO₃–HClO₄) extraction, and sequential extraction of stream sediments were performed. Heavy metal pollution of sediments was higher in Chonam-ri creek than in Sagok-ri creek, because there is a larger source of base metal sulfides in the ores and waste dump upstream of Chonam-ri creek. The sediment–water distribution coefficients (K _d) for metals in both creeks were dependent on the water pH and decreased in the order Pb ≈ Al > Cu > Mn > Zn > Co > Ni ≈ Cd. K _d values for Al, Cu and Zn were very sensitive to changes in pH. The results of sequential extraction indicated that among non-residual fractions, Fe–Mn oxides are most important for retaining trace metals in the sediments. Therefore, the precipitation of Fe(–Mn) oxides due to pH increase in downstream sites plays an important role in regulating the concentrations of dissolved trace metals in both creeks. For Al, Co, Cu, Mn, Pb and Zn, the metal concentrations determined by 0.1 N HCl extraction (Korean Standard Method for Soil Pollution) were almost identical to the cumulative concentrations determined for the first three weakly-bound fractions (exchangeable + bound to carbonates + bound to Fe–Mn oxides) in the sequential extraction procedure. This suggests that 0.1 N HCl extraction can be effectively used to assess the environmentally available and/or bioavailable forms of trace metals in natural stream sediments.