Evaluation of the ventilated chamber for measuring evaporation from a forest

Evaporation from a regenerating forest was determined concurrently by atmospheric measurements of the Bowen ratio, soil water depletion, and by weighing lysimeter. The methods agreed closely over 18 days in spring and 11 days in summer. Accordingly, the Bowen ratio technique was then used as the control against which any effect on evaporation by enclosure of the lysimeter with a chamber of varied ventilation rate could be quantified hourly and daily. Accuracy of gas analysis was checked against lysimeter values. Daily evaporation by the lysimeter was generally unaffected by enclosure—on a few afternoons there was a statistically significant enhancement of hourly values by the chamber. This was accounted for by difference in turbulence between chamber and forest. The general agreement in daytime hourly values is attributed to the frequent occurrence of equilibrium evaporation (rate at which evaporation is independent of ventilation). At night, evaporation was higher during enclosure. Comparisons were not possible with rain or dew. Determination of evaporation by gas analysis agreed within about 5 per cent of lysimeter values during a dry period. We conclude that the ventilated chamber as used provides realistic estimates of evaporation by forests. We show how periods of bias can be anticipated and corrected by theory.     

Interception loss from eucalypt forest: Lysimeter determination of hourly rates for long term evaluation

Analyses of the response by a weighing lysimeter in Kioloa State Forest during and after rainfall provided values of interception loss rate. The derived rates for time scales between 0.1 and 1.0mm h^?1 were generally similar throughout storm events to losses determined from throughfall and stemflow observations. During post-rainfall periods of canopy drying, enhanced rates of lysimeter evaporation were consistent with micrometeorological determinations of the partitioning of available radiant energy, based on atmospheric gradients of humidity and temperature. Interception losses from the eucalypt forest, deduced from the lysimeter response, varied between 10 and 15 per cent of gross rainfall in three consecutive 12 month periods whereas the corresponding rainfall ranged between 590 and 1530 mm yr^?1. Daytime losses accounted for about two-thirds of total interception loss with a similar fraction occurring during rain periods. Storage capacity of the evergreen forest canopy was inferred to be 0.35 mm. Hourly loss rates during rainfall ranged up to 0.8 mm h^?1 but with decreasing mean values and variability with increasing time scale resulting in a monthly mean value computed for the total number of hours of rain of approximately 0.1 mm h^?1. A preliminary analysis of loss rate in terms of storm windspeed and rainfall intensity explained about half of its variation in statistically derived relationships. Improved time resolution of the order of seconds was considered a prerequisite to the physical understanding of turbulent transport from saturated canopies. The small value of interception storage capacity was considered in relation to that for pine forest as a basis for explaining observed differences in interception behaviour between eucalypt forest and coniferous plantations in the same area. Large differences in interception losses between the Kioloa site and evergreen forest in the South Island of New Zealand and also eucalypt forest in Western Australia were attributed to dissimilar meteorological conditions at the various sites.     

Estimating winter evaporation in boreal forests with operational snow course data

Snow course measurements from 11 sites located in eastern and northern Finland were used to estimate the total interception evaporation of a winter season for different forest categories. We categorized the sites based on forest density and tree species. Results showed that interception loss from gross precipitation increased with forest density and approached 30% for a forest with the highest density class. Interception loss for the most common forest density class was 11%. Interception losses were slightly larger in spruce forests than in pine, deciduous, or mixed forests. We provide suggestions as to how to design snow surveys to estimate wintertime interception evaporation better. Rough terrain and transition zones between forest and open areas should be avoided. Since evaporation fraction was strongly dependent on tree crown characteristics, snow course data should include direct estimates of canopy closure. Qualitative observations made by different observers should be given a reference frame to ensure comparability of records from different sites. Copyright © 2003 John Wiley & Sons, Ltd.     

A note on estimating urban roof runoff with a forest evaporation model

A model developed for estimating the evaporation of rainfall intercepted by forest canopies is applied to estimate measurements of the average runoff from the roofs of six houses made in a previous study of hydrological processes in an urban environment. The model is applied using values of the mean rates of wet canopy evaporation and rainfall derived previously for forests and an estimate of the roof storage capacity derived from the data collected in the previous study. Although the model prediction is sensitive to the value of storage capacity, close correlation between the modelled and measured runoff indicates that the model captures the essential processes. It is concluded that the process of evaporation from an urban roof is sufficiently similar to that from a forest canopy for forest evaporation models to be used to give a useful estimate of urban roof runoff. Copyright © 2007 John Wiley & Sons, Ltd.     

An improved methodology to measure evaporation from bare soil based on comparison of surface temperature with a dry soil surface

Accurate estimation of the resistances to water vapor movement is a major difficulty in evaluating evaporation from soil. By including the temperature of a dry soil surface (the temperature of the surface of a dry soil column buried in the field), a method for estimating evaporation from soil is proposed. The necessary input variables for the suggested method are temperature, net radiation, and soil heat flux. There are three advantages of the proposed method over the conventional methods. First, soil surface resistance and aerodynamic resistance are not required. Second, the variables included are fewer. Third, measurement and analysis of the parameters involved are relatively easy. Sensitivity analysis shows that the suggested method is sensitive to temperatures. Test experiments were conducted in a sandy field, where a weighing lysimeter was installed. Evaporation from soil, together with the variables specified above, were measured. For temperatures measured by thermocouples, experimental results showed that the mean absolute error (MAE) for the daily evaporation over 22 days was 0.17 mm day⁻¹. The regression between calculated and measured evaporation was highly significant (r²=0.89). Moreover, the intercept and slope of the regression equation were not significantly different from zero and unity, respectively, at the 0.05 probability level. Furthermore, by using the temperatures measured by infrared thermometers, the MAE between measured evaporation and estimated evaporation was 0.15 mm day⁻¹. The regression between them was highly significant (r²=0.94). In addition, the intercept and slope of the regression equation were not significantly different from zero and unity, respectively, at the 0.05 probability level. These results show that evaporation calculated using the proposed method is in good agreement with lysimeter measured values. By comparing with the temperature difference method, it was shown that the suggested method estimated soil evaporation more accurately than the temperature difference method. Therefore, it is concluded that the proposed method is not only a simple way for application, but also an accurate way to estimate soil evaporation.     

A large weighing lysimeter for evapotranspiration and soil‐water–groundwater exchange studies

A large weighing lysimeter was installed at Yucheng Comprehensive Experimental Station, north China, for evapotranspiration and soil‐water–groundwater exchange studies. Features of the lysimeter include the following: (i) mass resolution equivalent to 0·016 mm of water to accurately and simultaneously determine hourly evapotranspiration, surface evaporation and groundwater recharge; (ii) a surface area of 3·14 m² and a soil profile depth of 5·0 m to permit normal plant development, soil‐water extraction, soil‐water–groundwater exchanges, and fluctuations of groundwater level; (iii) a special supply–drainage system to simulate field conditions of groundwater within the lysimeter; (iv) a soil mass of about 30 Mg, including both unsaturated and saturated loam. The soil consists mainly of mealy sand and light loam. Monitoring the vegetated lysimeter during the growing period of winter wheat, from October 1998 through to June 1999, indicated that during the period groundwater evaporation contributed 16·6% of total evapotranspiration for a water‐table depth from 1·6 m to 2·4 m below ground surface. Too much irrigation reduced the amount of upward water flow from the groundwater table, and caused deep percolation to the groundwater. Data from neutron probe and tensiometers suggest that soil‐water‐content profiles and soil‐water‐potential profiles were strongly affected by shallow groundwater. Copyright © 2000 John Wiley & Sons, Ltd.     

Formation of diamond with mineral inclusions of “mixed” eclogite and peridotite paragenesis

Two unusual diamonds were studied from kimberlites from China, which contain both ultramafic and eclogitic mineral inclusions in the same diamond hosts. Diamond L32 contains seven Fe-rich garnets, four omphacites and one olivine inclusion. Four olivine, one sanidine and one coesite were recovered from diamond S32. Both garnet and omphacite inclusions have similar compositions as those from other localities of the world, and show basaltic bulk composition. All the garnet and omphacite inclusions in diamond L32 have positive Eu anomalies (Eu/Eu^*1.64 1.79). These observations support the proposal that mantle eclogite is the metamorphic product of subducted ancient oceanic crust. The Mg/(Mg + Fe) ratio of the olivine inclusions from the two diamonds (91-92) are evidently lower than the normal olivine inclusions in diamonds from the same kimberlite pipe (92-95). The following model is proposed for the formation of diamonds with “mixed” mineral inclusions. Ascending diamond-bearing eclogite (recycled oceanic crust) entrained in mantle plumes may experience extensive partial melting, whereas the ambient peridotite matrix remains subsolidus in the diamond stable field. This provides a mechanism for the transport of diamond from its original eclogitic host to an ultramafic one. Subsequent re-growth of diamond in the new environment makes it possible to capture mineral inclusions of different lithological suites. Partial melts of basaltic sources may interact with the surrounding peridotite, resulting in the relatively lower Mg/(Mg + Fe) ratios of the coexisting olivine inclusions from the studied diamonds. Diamonds with “mixed” mineral inclusions demonstrate that plume activity also occurred in the Archean cratons.     

Magmatismes basiques dits “orogeniques” et “anorogeniques” et teneurs entro2: Les associations “Isotitanees” et “anisotitanfes”

The patterns of variation of TiO₂ conent during magmatic evolution are different in the so called “orogenic” and “anorogenie” basic associations; these last terms, which are the cause of much misunderstanding, can be replaced by the terms “isotitaniferous” and “anisotitaniferous”.     

A weighing lysimeter in a regenerating eucalypt forest: Design,construction, and performance

A 36 tonne monolithic weighing lysimeter (3.7 m diameter and 1.5 m deep) was installed in Kioloa State Forest near Batemans Bay, New South Wales, Australia, to provide a continuous record of water use from a regenerating natural eucaplyt community, five years old at installation. The resolution is equivalent to 0.05 mm of evaporation and provides hourly information for diurnal variation of forest evaporation. The sensitivity of 14 ppm compares favourably with those reported for other lysimeters, similar in magnitude, in the U.S.A. Design criteria for selecting, isolating and suspending a sample community ‘in situ’ with an electro-mechanical balance are outlined. Procedures adopted during installation are described with emphasis placed on precautions taken to minimize disturbance and to avert possible changes in character of the isolated natural community. Lysimeter performance was assessed both in terms of its accuracy and its operation as a remote facility with infrequent attention.     

Observation and estimation of evaporation from the ground surface of the cryosphere in eastern Asia

The characteristics of evaporation from the ground surface of Asian cryosphere sites are presented, as estimated by the lysimeter method, a profile method, and a heat budget method. The observation sites were located on the eastern Tibetan Plateau, in the Qilian and Tianshan Mountains of China, and in eastern Siberia. The lysimeter method has been demonstrated to be a reliable observation technique for estimating daily evaporation from the land surface, given suitable experiment design and operation. Daily mean evaporation varied within the range of 0·3 to 3·5 mm on the permafrost surface, and regional differences in evaporation were strongly related to surface soil moisture. Locally, topography, by way of its influence on surface soil moisture, was found to control evaporation systematically. Seasonality of ground evaporation in permafrost regions is dominated by thaw–freeze cycles at the surface; evaporation from the melting permafrost surface is up to four to seven times greater than that from frozen ground. In forested terrain, the interception of precipitation can reduce daily evaporation by 60 to 70%. Sublimation from the snow surface was observed at some sites in the range of 0·2 to 1·0 mm daily; atmospheric conditions, such as wind speed and saturation deficit, were dominant factors in determining snow sublimation. Copyright © 2003 John Wiley & Sons, Ltd.     

Observations of canopy storage capacity and wet canopy evaporation in a humid boreal forest

Evaporation of intercepted rain by a canopy is an important component of evapotranspiration, particularly in the humid boreal forest, which is subject to frequent precipitation and where conifers have a large surface water storage capacity. Unfortunately, our knowledge of interception processes for this type of environment is limited by the many challenges associated with experimental monitoring of the canopy water balance. The objective of this study is to observe and estimate canopy storage capacity and wet canopy evaporation at the sub-daily and seasonal time scales in a humid boreal forest. This study relies on field-based estimates of rainfall interception and evapotranspiration partitioning at the Montmorency Forest, Québec, Canada (mean annual precipitation: 1600 mm, mean annual evapotranspiration: 550 mm), in two balsam fir-white birch forest stands. Evapotranspiration was monitored using eddy covariance sensors and sap flow systems, whereas rainfall interception was measured using 12 sets of throughfall and six stemflow collectors randomly placed inside six 400-m² plots. Changes in the amount of water stored on the canopy were also directly monitored using the stem compression method. The amount of water intercepted by the forest canopy was 11 ± 5% of the total rainfall during the snow-free (5 July–18 October) measurement periods of 2017 and 2018. The maximum canopy storage estimated from rainfall interception measurements was on average 1.6 ± 0.7 mm, though a higher value was found using the stem compression method (2.2 ± 1.6 mm). Taking the average of the two forest stands studied, evaporation of intercepted water represented 21 ± 8% of evapotranspiration, while the contribution of transpiration and understory evapotranspiration was 36 ± 9% and 18 ± 8%. The observations of each of the evapotranspiration terms underestimated the total evapotranspiration observed, so that 26 ± 12% of it was not attributed. These results highlight the importance to account for the evaporation of rain intercepted by humid boreal forests in hydrological models.     

The “wave turbopause”

The “wave turbopause” is defined as the mesospheric altitude level where the temperature fluctuation field indicates a substantial increase in wave amplitudes in the vertical direction.The turbopause altitude is analyzed on the basis of four years of SABER data (2002–2005, Version 1.06). Substantial seasonal and latitudinal variations are found, with some interannual variability also present. Seasonal changes are annual at high latitudes, semi-annual at low latitudes, and a mixture of both at middle latitudes. Southern hemisphere data are similar as in the North if shifted by half a year. Latitudinal variations show a minimum in the tropics and two relative maxima at middle latitudes.The “wave turbopause” is found near to zero-wind lines or low-wind zones (zonal wind). It is compared to rocket and other measurements, and interesting similarities are obtained. The wave turbopause can also be found in the HAMMONIA GCM. A preliminary analysis shows results similar to those of the SABER measurements.     

“Site & region-specific” response spectra: a probabilistic approach

Design seismic forces depend on Peak Ground Acceleration (PGA) values and on the shape of Response Spectrum (RS) curves dictated by Building Codes or which need to be evaluated in every particular case. The PGA values and RS curves strictly depend on earthquake magnitude and distance, as well as on the regional and local geological conditions. At present, there is no doubt that it is necessary to construct so-called “Site & Region-specific” Building Code provisions reflecting the influence of different magnitude events at different distances that may occur during the life time of the construction, as well as the variety of local ground conditions. A scheme of Uniform Hazard Response Spectra and PGA estimation considering local site response is described in this paper. The assessments of these design parameters are obtained on the basis of Uniform Hazard Fourier spectra using the conception of “dominant earthquakes”. The effect of local geology is included by means of the soil/reference site spectral ratios.     

“Andesitic water”: a phantom of the isotopic evolution of water-silicate systems. Comment on “Isotopic shifts in waters from geothermal and volcanic systems along convergent plate boundaries and their origin” by W.F. Giggenbach

On account of the low porosity of the lithosphere, intracrustal fluids behave very differently from surface fluids, in that they are changing their geochemical and isotopic labels according to the geological environment. Given a heat source, meteoric waters can be supplied plentifully and their rates of throughput in geothermal systems are sufficiently high to exhaust the compositional signals of a given rock buffer. In contrast, fluids exsolved from magma, and subducted fluids, would be supplied at less than about one tenth of the meteoric rate over the life time of a system. Based on up-to-date flow models, the isotopic evolution of meteoric water interacting with crustal rock follows a curved to L-shaped track in the δD versus δ¹⁸O plot. Instantaneous (present-day) tie-lines between recharge and discharge are secants of such tracks and can have a range of slopes. At the start of an interaction, waters have δD and δ¹⁸O values approaching equilibrium with the original rock composition (water “W1”). Using known hydrogen isotope fractionation factors, W1 values generally plot in the region of “andesite” or “andesitic” waters of various authors. Since the W1 waters have δD values that are on average more positive, and also less variable than those of the meteoric recharges, most tracks and tie-lines have positive slopes, and the plotting of a large number of tie-lines will produce a focus on the field of W1 waters, regardless of the original water source.     

A soil‐water‐balance approach to quantify groundwater recharge from irrigated cropland in the North China Plain

Rapidly depleting unconfined aquifers are the primary source of water for irrigation on the North China Plain. Yet, despite its critical importance, groundwater recharge to the Plain remains an enigma. We introduce a one‐dimensional soil‐water‐balance model to estimate precipitation‐ and irrigation‐generated areal recharge from commonly available crop and soil characteristics and climate data. To limit input data needs and to simplify calculations, the model assumes that water flows vertically downward under a unit gradient; infiltration and evapotranspiration are separate, sequential processes; evapotranspiration is allocated to evaporation and transpiration as a function of leaf‐area index and is limited by soil‐moisture content; and evaporation and transpiration are distributed through the soil profile as exponential functions of soil and root depth, respectively. For calibration, model‐calculated water contents of 11 soil‐depth intervals from 0 to 200 cm were compared with measured water contents of loam soil at four sites in Luancheng County, Hebei Province, over 3 years (1998–2001). Each 50‐m² site was identically cropped with winter wheat and summer maize, but received a different irrigation treatment. Average root mean‐squared error between measured and model‐calculated water content of the top 180 cm was 4·2 cm, or 9·3% of average total water content. In addition, model‐calculated evapotranspiration compared well with that measured by a large‐scale lysimeter. To test the model, 12 additional sites were simulated successfully. Model results demonstrate that drainage from the soil profile is not a constant fraction of precipitation and irrigation inputs, but rather the fraction increases as the inputs increase. Because this drainage recharges the underlying aquifer, improving irrigation efficiency by reducing seepage will not reverse water‐table declines. Copyright © 2003 John Wiley & Sons, Ltd.     

Estimation of vertical profiles of leaf drying times after daytime rainfall within a Bornean tropical rainforest

South‐east Asian Bornean tropical rainforests have large and complex canopy structures. To clarify how forest structure affects wet‐canopy evaporation, it is necessary to consider wet‐canopy evaporation processes within the forest canopy, such as vertical profiles of canopy drying time. In a previous study a method was proposed that utilizes sap flow measurements to estimate canopy drying time after rainfall (CDTobs) during daytime. In this present study, the method was applied to estimations of the vertical variations in CDTobs in 11 individual trees of various heights, ranging from 2·7 m to 53 m. The study derived vertical profiles and showed that the lengths of CDTobs in lower canopy trees were 2–4 h longer than those in the upper canopy trees. The new method for CDTobs profiles presented in this study, which is available for validation of multi‐layer biosphere‐atmospheric models, is a useful illustration for clarifying wet‐canopy evaporation processes in tropical rainforests. Copyright © 2008 John Wiley & Sons, Ltd.     

Energy balance above a boreal coniferous forest: a difference in turbulent fluxes between snow‐covered and snow‐free canopies

To evaluate the interactive effects of snow and forest on turbulent fluxes between the forest surface and the atmosphere, the surface energy balance above a forest was measured by the eddy correlation method during the winter of 1995–1996. The forest was a young coniferous plantation comprised of spruce and fir. The study site, in Sapporo, northern Japan, had heavy and frequent snowfalls and the canopy was frequently covered with snow during the study period. A comparison of the observed energy balance above the forest for periods with and without a snow‐covered canopy and an analysis using a single‐source model gave the following results: during daytime when the canopy was covered with snow, the upward latent heat flux was large, about 80% of the net radiation, and the sensible heat flux was positive but small. On the other hand, during daytime when the canopy was dry and free from snow, the sensible heat flux was dominant and the latent heat flux was minor, about 10% of the net radiation. To explain this difference of energy partition between snow‐covered and snow‐free conditions, not only differences in temperature but also differences in the bulk transfer coefficients for latent heat flux were necessary in the model. Therefore, the high evaporation rate from the snow‐covered canopy can be attributed largely to the high moisture availability of the canopy surface. Evaporation from the forest during a 60‐day period in midwinter was estimated on a daily basis as net radiation minus sensible heat flux. The overall average evaporation during the 60‐day period was 0·6 mm day⁻¹, which is larger than that from open snow fields. Copyright © 1999 John Wiley & Sons, Ltd.     

Estimation of groundwater evaporation and salt flux from Owens Lake, California, USA

Groundwater evaporation and subsequent precipitation of soluble salts at Owens Lake in eastern California have created one of the single largest sources of airborne dust in the USA, yet the evaporation and salt flux have not been fully quantified. In this study, we compare eddy correlation, microlysimeters and solute profiling methods to determine their validity and sensitivity in playa environments. These techniques are often used to estimate evaporative losses, yet have not been critically compared at one field site to judge their relative effectiveness and accuracy. Results suggest that eddy correlation methods are the most widely applicable for the variety of conditions found on large playa lakes. Chloride profiling is shown to be highly sensitive to thermal and density-driven fluxes in the near surface and, as a result, appears to underestimate yearly groundwater evaporation. Yearly mean groundwater evaporation from the playa surface estimated from the three study areas was found to range from 88 to 104 mm year⁻¹, whereas mean evaporation from the brine-covered areas was 872 mm year⁻¹. Uncertainties on these mean rates were estimated to be ±25%, based on comparisons between eddy correlation and lysimeter estimates. On a yearly basis, evaporation accounts for approximately 47 × 10⁶ m³ of water loss from the playa surface and open-water areas of the lake. Over the playa area, as much as 7.5 × 10⁸ kg (7.5 × 10⁵ t) of salt are annually concentrated by evaporation at or near the playa surface, much of which appears to be lost during dust storms in area.