中国典型高温热田热水的锶同位素研究

滇藏地热带的热水大多是大气降水成因，大气降水沿断裂带向下渗透，随地温的增加而逐步升温，并不断地与深部岩石发生水岩相互作用，从造岩矿物中淋滤出锶组分。通过测定热水中的锶同位素组成，可以帮助确定热水的深部滞留环境，研究深、浅层热水的内在联系，区分出不同的水热循环系统。西藏羊八井热田深部由多期次花岗岩组成，岩性差别不大，而锶同位素差异比较明显。热田的深、浅层热水有着相似的^87Sr/^86Sr值，并且只与上新世花岗岩的锶同位素组成相接近，反映了深部热储的岩性特征。在热水从升流部位向排泄区运移时，浅层冷水、始新世火山岩和第四系砂砾岩对热水的锶同位素改造作用较小。云南腾冲热海热田是典型的有幔源岩浆囊作为热源的高温热田，热田由东、西两区组成，其气体和热水在化学组成上有一定的差异，^87Sr/^86Sr值也有明显的不同。因此，可以确定东、西两区的水热系统虽具有共同的热源，但两者之间的水力联系比较微弱，而且热水中的锶组分与热田内大面积出露的火山岩没有关联。     

漳州盆地水热系统氚同位素研究

本文依据26个天然水样品的氚同位素测试数据,分析了漳州盆地地下热水及其它天然水的氚值特征及其形成条件;利用“活塞模型”方法计算了漳州盆地地下水和地下热水的年龄;为弄清全盆地地下水的补给、迳流和排泄的总体格局和揭示地下热水的成因提供了依据。     

青海共和盆地地热流体地球化学特征及热储水-岩相互作用过程

地热流体地球化学组成及其运移规律和成因机制研究对地热资源勘查和开发利用具有重要意义。当前,青海省地热资源开发利用程度低,更缺乏针对地热流体地球化学特征进行深入研究的系统性工作。青海共和盆地是青藏高原北缘的一个断陷盆地,盆地内地热资源丰富。本文以共和盆地及周围部分山区的地热系统为研究对象,基于系统地球化学采样和测试开展了地热流体地球化学组成及热储水-岩相互作用过程分析,认为:从共和下更新统热储、新近系热储到鄂拉山构造岩浆带再到瓦里贡山构造岩浆带,地热水中SiO₂含量依次升高,反映热储温度依次升高;上述地热地区热储中原生铝硅酸盐矿物的溶解和蚀变矿物的形成是控制地热水中阳离子含量的最重要的水文地球化学过程,而补给水下渗和地热水径流及升流过程中盐类矿物的溶滤则是水中阴离子(特别是 {\mathrm{SO}}_4^{2-}和Cl^-)的主要来源。     

西藏搭格架高温热泉中钨的水文地球化学异常

西藏搭格架水热区的热泉含异常高浓度的钨,其钨/钼比也远高于常见天然水.开展了搭格架典型热泉的地球化学研究,发现中性热泉的钨浓度显著高于偏酸性热泉:前者是深部母地热流体经绝热冷却、传导冷却等过程后排出地表而形成,其中的钨主要来自岩浆水的贡献;而后者为中性地热水和蒸汽加热型强酸性水的混合产物,贫钨蒸汽加热型水的稀释使其钨浓度不同程度降低.在地热水中,钨与典型保守组分氯相似,不易自液相沉淀或被热储介质吸附;但地热水含硫化物时,钼则极易以辉钼矿的形式沉淀,导致搭格架热泉的钨/钼比偏高.虽然搭格架地热水中存在硫化物,但钨在水中主要以钨酸盐的形式存在,少量硫代钨酸盐的形成对钨的水文地球化学过程影响不大.      

Characteristics of the Reservoir of the Rehai Geother-mal Field in Tengchong,Yunnan Province,China1

Abstract The Rehai geothermal field in Tengchong County, Yunnan Province is a significant high- temperature hydrothermal convective system. The geothermal reservoir is composed of granite. Various geothermometers are used to evaluate the reservoir temperature. The most likely temperature of the reservoir as represented by T_Na-K-Ca is about 230 °C. The chemical and isotopic compositions of fluids before boiling within the reservoir are estimated. The mixing and dilution of cold and warm waters are discussed. The Rehai geothermal field is a high- temperature (hot) water system with the subsurface boiling zone close to the surface. The reservoir pressure at different depths is calculated. And finally the water-rock equilibration is inferred.     

Hydrochemical,isotopic, and reservoir characterization of the Pasinler (Erzurum) geothermal field,eastern Turkey

The reservoir temperature and conceptual model of the Pasinler geothermal area, which is one of the most important geothermal areas in Eastern Anatolia, are determined by considering its hydrogeochemical and isotope properties. The geothermal waters have a temperature of 51 °C in the geothermal wells and are of Na–Cl–HCO₃ type. The isotope contents of geothermal waters indicate that they are of meteoric origin and that they recharge on higher elevations than cold waters. The geothermal waters are of immature water class and their reservoir temperatures are calculated as 122–155 °C, and their cold water mixture rate is calculated as 32%. According to the δ¹³C_VPDB values, the carbon in the geothermal waters originated from the dissolved carbon in the groundwaters and mantle-based CO₂ gases. According to the δ³⁴S_CDT values, the sources of sulfur in the geothermal waters are volcanic sulfur, oil and coal, and limestones. The sources of the major ions (Na⁺, Ca²⁺, Mg²⁺, Cl^?, and HCO₃ ^?) in the geothermal waters are ion exchange and plagioclase and silicate weathering. It is determined that the volcanic rocks in the area have effects on the water chemistry and elements like Zn, Rb, Sr, and Ba originated from the rhyolite, rhyolitic tuff, and basalts. The rare earth element (REE) content of the geothermal waters is low, and according to the normalized REE diagrams, the light REE are getting depleted and heavy REE are getting enriched. The positive Eu and negative Ce anomalies of waters indicate oxygen-rich environments.     

Oxygen isotope studies of the geothermal system at Wairakei,New Zealand

Volcanic rocks in the Wairakei geothermal field have undergone extensive oxygen isotope exchange with the thermal waters, resulting in an O¹⁸-depletion averaging about 4%. A lower limit on the ratio of the mass of water to rock in the exchange system is 4·3, at least ten times greater than the corresponding figure for the Salton Sea geothermal system. Carbonates, present as alteration products in most samples, are found to be in equilibrium with waters at present-day temperatures in some wells, and to record higher ‘fossil’ temperatures in others. Quartz phenocrysts and xenocrysts remain unexchanged, and only new hydrothermal quartz is in isotopic equilibrium with geothermal solutions.     

Fluid inclusion study constraining the hydrothermal evolution of caldera-forming volcanic systems in the Sengan Area, Northern Honshu, Japan

Summary The hydrothermal evolution of the Sengan geothermal area, Northern Honshu, was studied using fluid inclusion microthermometry. Sengan is one of the most active geothermal areas in Japan, and it is dominated by andesitic to dacitic volcanic rocks of Pliocene and Quaternary age. Fluid inclusions were studied in hydrothermal minerals (quartz, calcite, anhydrite, wairakite) and in fractured igneous quartz phenocrysts from core samples retrieved from five geothermal exploration wells, which penetrated Quaternary and Tertiary formations, and intrusive rocks in or around the calderas. A caldera-hosted hydrothermal system was heated by a shallow intrusion, which produced hypersaline fluids. During the early stages some heterogeneity in fluid composition occurred, but during peak activity of the hydrothermal system, the fluid was dominantly low-salinity, and most likely of meteoric origin. We have reconstructed, by means of fluid inclusion studies, the structure of an extinct hydrothermal system in a Pliocene caldera filled with ignimbrites, and of an active hydrothermal system which is now being heated under the northern slope of Yakeyama volcano. Based on inclusion data, the aqueous fluids that circulated in the hydrothermal system ranged from very low saline (0–7 wt.% NaCl equiv.) to hypersaline (up to 60 wt.% NaCl equiv.), with temperatures ranging from 130 to 400 °C.     

Tracing hydrothermal mineral thenardite in geysers/hot springs of North-western Himalayan belt,Ladakh Geothermal Province,India by hydrogeochemistry,fluid-mineral equilibria and isotopic studies

The present study highlights the first evidence of hydrothermal mineral Thenardite (Na₂SO₄) from Puga geothermal area, North-western Himalayan belt in Ladakh Geothermal Province, India, which is unequivocal evidence for the presence of high-temperature hydrothermal fluid activity from one of the thickest crust areas of the Earth. The Puga geothermal belt illustrates a fault-bounded hydrothermal system with a clearly defined conductive zone, coinciding with Kiagar Tso fault typically exemplifying a shallow-level medium enthalpic geothermal reservoir. The hydrogeochemistry suggests that thermal and non-thermal waters are of Na-Cl-HCO₃ and Ca-Mg-HCO₃ type, respectively, with neutral to near alkaline pH. The silica and cation geothermometry reveal sub-surface temperatures around 150 °C and 250 °C, respectively, at shallow depth; however, >250 °C is anticipated at the deepest levels (~3 km). Stable isotope (δD and δ¹⁸O) studies explicate depletion of isotopic content for thermal waters over Puga river water and radiogenic isotope (³H) suggests matured thermal waters with ongoing water-rock interactions. The recharge altitude estimation and physiographic studies put forth that geothermal reservoir is recharged with the ice masses located at an altitude of 6458 m above mean sea level (msl) in the west of Puga valley, probably from the highest peak of Polokong La mountain. The two key processes participating in regulation of proportions of the dissolved salts in the thermal waters are silicate weathering and ion-exchange kinetics. The powder X-ray diffraction study reveals a major occurrence of hydrothermal mineral thenardite in the hot spring deposits for the first time along with huge encrustations of trona, borax, calcite and elemental sulfur. The high-temperature fluids encounter thenardite, pyrite, and jarosite-bearing minerals in basement rock causing enrichment of SO₄²⁻ and Cl⁻ in geothermal waters. The temperature-dependent speciation modelling (50 °C–200 °C) for major ion Na⁺ reveals the composition of the reservoir fluid (~150 °C): Na⁺ > NaCO₃⁻ > NaSO₄⁻ > NaHCO₃ > NaF > NaOH. A conceptual evolution model of thermal waters involving the recharge-deep circulation-mixing-discharge of thermal springs is hence put forth in the study using various hydrogeochemical insights.     

Hydrogeochemical investigation of geothermal springs in Erzurum,East Anatolia (Turkey)

Geothermal water sources located within The Erzurum province were identified and hot water samples were taken from four different geothermal areas. The results of in situ and hydrogeochemical analyses of these hot water samples were interpreted and the properties of hot water, water–rock associations, estimated reservoir temperature and hot water usage areas were determined. The temperatures of the samples collected from the study area vary between 26.2 and 57.7 °C, while pH values change from 6.09 to 7.33, EC values obtained from in situ measurements are between 1829 and 9480 µS/cm and Eh values are (??190) to (26.3) mV. Total dissolved solids of the hot waters have a range from 838.7 to 3914.1 mg/l. The maximum estimated reservoir temperature is calculated as 250 °C by applying chemical geothermometers. However, considering the actual temperatures of Pasinler, Köprüköy, Horasan and Il?ca thermal waters and wells, the most reliable temperature range depending on the applied geothermometers’ results indicate minimum and maximum reservoir temperatures 85–158.9 °C, respectively, taking in account the errors. According to the isotope analysis, the waters circulating within the geothermal system are of meteoric origin and modern waters. In addition, two samples taken from clayey levels observed in the field were analyzed and the mineralogy of the clays was evaluated.     

Hydrogeochemistry of thermal and mineralized waters in the Diyadin (Ağri) area,Eastern Turkey

The Diyadin Geothermal area, located in the eastern part of Anatolia (Turkey) where there has been recent volcanic activity, is favorable for the formation of geothermal systems. Indeed, the Diyadin geothermal system is located in an active geodynamic zone, where strike-slip faults and tensional cracks have developed due to N–S regional compression. The area is characterized by closely spaced thermal and mineralized springs, with temperatures in the range 30–64 °C, and flowrates 0.5–10 L/s. Thermal spring waters are mainly of Ca(Na)-HCO₃ and Ca(Mg)-SO₄ types, with high salinity, while cold groundwater is mostly of Ca(Na, Mg)-HCO₃ type, with lower salinity. High contents of some minor elements in thermal waters, such as F, B, Li, Rb, Sr and Cs probably derive from enhanced water–rock interaction.Thermal water samples collected from Diyadin are far from chemical equilibrium as the waters flow upward from reservoirs towards spring vents and possibly mix with cooler waters. The temperatures of the deep geothermal reservoirs are estimated to be between 92 and 156 °C in Diyadin field, based on quartz geothermometry, while slightly lower estimates are obtained using chalcedony geothermometers. The isotopic composition of thermal water (δ¹⁸O, δ²H, δ³H) indicates their deep-circulating meteoric origin. The waters are likely to have originated from the percolation of rainwater along fractures and faults to the deep hot reservoir. Subsequent heating by conduction due to the presence of an intrusive cupola associated with the Tendurek volcano, is followed by the ascent of deep waters to the surface along faults and fractures that act as hydrothermal conduits.Modeling of the geothermal fluids indicates that the fluid is oversaturated with calcite, aragonite and dolomite, which matches travertine precipitation in the discharge area. Likewise, the fluid is oversaturated with respect to quartz, and chalcedony indicating the possibility of siliceous precipitation near the discharge areas. A conceptual hydro-geochemical model of the Diyadin thermal waters based on the isotope and chemical analytical results, has been constructed.     

川藏铁路康定隧址区地热水成因及其工程影响分析

川藏铁路康定隧址区穿越鲜水河断裂带,属地热异常区,对铁路建设造成一定的热害威胁。采用野外调查、水化学分析和氢氧同位素测试等技术方法,开展了川藏铁路康定隧址区地热水成因研究。结果表明,康定隧址区地热水水化学类型主要为HCO₃·Cl—Na和HCO₃—Na型,聚集于折多塘、康定和中谷3个热水区。地热水均为未成熟水,热储温度为104～172 ℃,深部初始地热水温度为186～250 ℃,冷水混合比例为0.56～0.81。氢氧同位素显示地热水补给高程为3768～4926 m。在康定隧址区,地热水受到高海拔水源补给,主体断裂构造为导热构造,次级分支断裂和发育节理、裂隙的断层破碎带为导水构造,地热水形成后沿浅部断层破碎带出露形成温泉。FEFLOW数值模拟分析表明研究区100 m深度地温场温度为35.4～95.1 ℃,研究区内三个热水区之间存在低温通道。隧道建设时应重点关注康定热水区的高温水热灾害。     

Boron geochemistry from some typical Tibetan hydrothermal systems: Origin and isotopic fractionation

The Tibetan plateau is characterized by intense hydrothermal activity and abnormal enrichment of trace elements in geothermal waters. Hydrochemistry and B isotope samples from geothermal waters in Tibet were systematically measured to describe the fractionation mechanisms and provide constraints on potential B reservoirs. B concentrations range from 0.35 to 171.90 mg/L, and isotopic values vary between −16.57 ‰ and +0.52 ‰. Geothermal fields along the Indus-Yarlung Zangbo suture zone and N–S rifts are observed with high B concentrations and temperatures. The similar hydrochemical compositions of high-B geothermal waters with magmatic fluid and consistent modeling of B isotopic compositions with present δ¹¹B values imply that the B in high-B geothermal waters is mainly contributed by magmatic sources, probably through magma degassing. In contrast, geothermal fields in other regions of the Lhasa block have relatively low B concentrations and temperatures. After considering the small fractionation factor and representative indicators of Na/Ca, Cl/HCO₃, Na + K and Si, the conformity between modeling results and the isotopic compositions of host rocks suggests that the B in low-temperature geothermal fields is mainly sourced from host rocks. According to simulated results, the B in some shallow geothermal waters not only originated from mixing of cold groundwater with deep thermal waters, but it was also contributed by equilibration with marine sedimentary rocks with an estimated proportion of 10%. It was anticipated that this study would provide useful insight into the sources and fractionation of B as well as further understanding of the relationships between B-rich salt lakes and geothermal activities in the Tibetan plateau.     

Geochemical constraint on origin and evolution of solutes in geothermal springs in western Yunnan,China

Geothermal resources are very rich in Yunnan, China. However, source of dissolved solutes in geothermal water and chemical evolution processes remain unclear. Geochemical and isotopic studies on geothermal springs and river waters were conducted in different petrological-tectonic units of western Yunnan, China. Geothermal waters contain Ca–HCO₃, Na–HCO₃, and Na (Ca)–SO₄ type, and demonstrate strong rock-related trace elemental distributions. Enhanced water–rock interaction increases the concentration of major and trace elements of geothermal waters. The chemical compositions of geothermal waters in the Rehai geothermal field are very complicated and different because of the magma chamber developed at the shallow depth in this area. In this geothermal field, neutral-alkaline geothermal waters with high Cl, B, Li, Rb Cs, As, Sb, and Tl contents and acid–sulfate waters with high Al, Mn, Fe, and Pb contents are both controlled by magma degassing and water–rock interaction. Geothermal waters from metamorphic, granite, and sedimentary regions (except in the Rehai area) exhibit varying B contents ranging from 3.31 mg/L to 4.49 mg/L, 0.23 mg/L to 1.24 mg/L, and <0.07 mg/L, respectively, and their corresponding δ¹¹B values range from −4.95‰ to −9.45‰, −2.57‰ to −8.85‰, and −4.02‰ to +0.06‰. The B contents of these geothermal waters are mainly controlled by leaching host rocks in the reservoir, and their δ¹¹B values usually decrease and achieve further equilibrium with its surrounding rocks, which can also be proven by the positive δ¹⁸O-shift. In addition to fluid–rock reactions, the geothermal waters from Rehai hot springs exhibit higher δ¹¹B values (−3.43‰ to +1.54‰) than those yielded from other areas because mixing with the magmatic fluids from the shallow magma. The highest δ¹¹B of steam–heated waters (pH 3.25) from the Zhenzhu spring in Rehai is caused by the fractionation induced by pH and the phase separation of coexisting steam and fluids. Given the strong water–rock interaction, some geothermal springs in western Yunnan show reservoir temperatures higher than 180 °C, which demonstrate potential for electricity generation and direct-use applications. The most potential geothermal field in western Yunnan is located in the Rehai area because of the heat transfer from the shallow magma chamber.     

Hydrogeochemical and isotopic characteristics of the Ilica geothermal system (Erzurum,Turkey)

In this paper, the hydrochemical isotopic characteristics of samples collected from geothermal springs in the Ilica geothermal field, Eastern Anatolia of Turkey, are examined and described. Low-temperature geothermal system of Ilica (Erzurum, Turkey) located along the Eastern Anatolian fault zone was investigated for hydrogeochemical and isotopic characteristics. The study of ionic and isotopic contents shows that the thermal water of Ilica is mainly, locally fed by groundwater, which changes chemically and isotopically during its circulation within the major fault zone reaching depths. The thermal spring has a temperature of 29–39 °C, with electrical conductivity ranging from 4,000 to 7,510 µS/cm and the thermal water is of Na–HCO₃–Cl water type. The chemical geothermometers applied in the Ilica geothermal waters yielded a maximum reservoir temperature of 142 °C according to the silica geothermometers. The thermal waters are undersaturated with respect to gypsum, anhydrite and halite, and oversaturated with respect to dolomite. The dolomite mineral possibly caused scaling when obtaining the thermal waters in the study area. According to the enthalpy chloride-mixing model, cold water to the thermal water-mixing ratio is changing between 69.8 and 75 %. The δ¹⁸O–δ²H compositions obviously indicate meteoric origin of the waters. Thermal water springs derived from continental precipitation falling on to higher elevations in the study area. The δ¹³C ratio for dissolved inorganic carbonate in the waters lies between 4.63 and 6.48 ‰. In low-temperature waters carbon is considered as originating from volcanic (mantle) CO₂.     

西藏羊应乡地热田形成特点及评价探讨

羊应乡地热田内出露的有关岩石，在地表以火山熔岩和火山碎屑岩为主，地表以下则有大量黑云母花岗斑岩分布。热田的形成与火成岩有较密切的关系，地表热显示的类型多种多样，有热泉、沸泉、沸喷泉、喷气孔、冒气地面和泉华等。根据其出露特征可分为四个区。经铀系法测定其水热活动的同位素年龄为１４．６Ｍａ左右，结合地层对比，认为水热活动时间为中更新世晚期。区内近Ｓ—Ｎ向的主要大断裂和两组次一级的断裂是水热活动的主要通道和主要控热构造裂隙。初步认为热田应属与岩浆活动有关的地热田、目前热田处于产热与散热大致平衡或散热略大于产热的基本平衡状态，探明的热水温度已高达２０７℃。     

Hydrogeology of thermal waters in Viterbo area, central Italy

A conceptual hydrogeological model of the Viterbo thermal area (central Italy) has been developed. Though numerous studies have been conducted on its geological, geochemical and geothermal features, there is no generalized picture defining the origin and yield of the hydrothermal system. These latter aspects have therefore become the objectives of this research, which is based on new hydrogeological and geochemical investigations. The geological setting results in the coexistence of overlapped interacting aquifers. The shallow volcanic aquifer, characterized by fresh waters, is fed from the area around the Cimini Mountains and is limited at its base by the semiconfining marly-calcareous-arenaceous complex and low-permeability clays. To the west of Viterbo, vertical upflows of thermal waters of the sulphate-chloride-alkaline-earth type with higher gas contents, are due to the locally uplifted carbonate reservoir, the reduced thickness of the semiconfining layer and the high local geothermal gradient. The hot waters (30–60°C) are the result of deep circulation within the carbonate rocks (0.5–1.8 km) and have the same recharge area as the volcanic aquifer. The upward flow in the Viterbo thermal area is at least 0.1 m³/s. This flow feeds springs and deep wells, also recharging the volcanic aquifer from below.     

Mixing processes in hydrothermal spring systems and implications for interpreting geochemical data: a case study in the Cappadocia region of Turkey

Mixing is a dominant hydrogeological process in the hydrothermal spring system in the Cappadocia region of Turkey. All springs emerge along faults, which have the potential to transmit waters rapidly from great depths. However, mixing with shallow meteoric waters within the flow system results in uncertainty in the interpretation of geochemical results. The chemical compositions of cold and warm springs and geothermal waters are varied, but overall there is a trend from Ca–HCO₃ dominated to Na–Cl dominated. There is little difference in the seasonal ionic compositions of the hot springs, suggesting the waters are sourced from a well-mixed reservoir. Based on δ¹⁸O and δ²H concentrations, all waters are of meteoric origin with evidence of temperature equilibration with carbonate rocks and evaporation. Seasonal isotopic variability indicates that only a small proportion of late spring and summer precipitation forms recharge and that fresh meteoric waters move rapidly into the flow system and mix with thermal waters at depth. ³H and percent modern carbon (pmC) values reflect progressively longer groundwater pathways from cold to geothermal waters; however, mixing processes and the very high dissolved inorganic carbon (DIC) of the water samples preclude the use of either isotope to gain any insight on actual groundwater ages.     

Composition of geothermal minerals from saline and dilute fluids — Krafla and Reykjanes, Iceland

In high temperature geothermal areas (T.200°C) in Iceland the alteration minerals formed show a regular zoning with increasing temperature i.e. smectite, chlorite, epidote and actinolite. To test the effect of varying composition of the hydrothermal circulation fluid drillhole chips from two contrasting areas were analyzed in detail. The Reykjanes area is fed with sea water while Krafla is fed with meteoric water and has a Cl⁻ concentration of 28 ppm. Both areas have tholeiitic basalts, lavas and hyaloclastites as original reservoir rocks.

Although both systems have the same sequence of alteration minerals the actual composition of the minerals differs between systems reflecting the different chemical composition of the circulating waters. In Reykjanes, with its brine fluid, the composition of the original rock appears not to affect the composition of the alteration minerals while the reverse appears to be the case in Krafla.     

Zeolites in volcanic-igneous hydrothermal systems: a case study of Pauzhetka geothermal field (Kamchatka) and Oligocene Smrekovec volcanic complex (Slovenia)

Production from geothermal reservoirs in volcanic-igneous hydrothermal systems may be disturbed owing to the formation of authigenic minerals that reduce primary porosity and infill fissure systems. Crystallization may be induced by natural processes or human activity related to the reservoir exploitation. In volcanic and volcaniclastic rocks, zeolites and related authigenic silicate minerals commonly develop. Two selected study sites—Pauzhetka geothermal field in Russia and Smrekovec volcanic complex in Slovenia are characterized by extensive development of progressive stage medium- and low-temperature propylitization and zeolitization with similar mineral assemblages that reduced original reservoir rock porosity and permeability. Retrograde and overprinting reactions of argillitization commonly enhance porosity and permeability of rocks, but some other reactions, like from prehnite to laumontite, from laumontite to heulandite, and from laumontite to analcime, encountered in the Smrekovec volcanic complex reduced it appreciably. Retrograde reactions recognized in the study sites were not induced by the temperature drop only, but were accompanied by the change in chemical composition of reacting fluids. Chemical composition of interstitial waters produced from exploitation wells in the Pauzhetka geothermal field indicate that propylitic and zeolite facies alteration is related to Na–Cl, slightly alkaline waters, while argillitization involved acidic thermal waters with more complex ion composition.