Shear Strength of Jumunjin Sand according to Relative Density

The properties of sands pertaining to shear strength have been studied extensively by plane strain and triaxial tests for relative densities above 40%. Unfortunately, properties of sand have not been comprehensively studied for relative density below 40%. An experimental investigation of the shear strength of Jumunjin sand was carried out using a plane strain, triaxial and direct shear apparatus according to relative density ranges from 0 to 100%. Because of the complexity of the shear tests on coarse materials, correlations were developed that would be useful for practical purposes. This article presents a comparison of strength properties' results and their correlation with relative density.     

Undrained Dynamic Strength Behavior of Saturated Nanjing Fine Sand under Wave Load

Cyclic vertical-torsional coupling tests were performed on saturated Nanjing fine sand with a relative density of 50% using a hollow cylinder apparatus. The effect of complex initial stress conditions on undrained dynamic strength of saturated Nanjing fine sand was investigated. It is shown that the initial confining pressure, p₀, the initial stress ratio, R₀, and the initial angle of maximum principal stress direction, α₀, have great effects on the characteristics of the dynamic strength of Nanjing fine sand. The dynamic strength increases with p₀ and R₀, while it decreases with α₀. The effect of initial intermediate principal stress parameter b₀ on the dynamic strength is slight.     

Monitoring hawksbill turtle nesting sites in some protected areas from the Persian Gulf

Iranian nesting populations of the critically endangered hawksbill turtle(Eretmochelys imbricate) are some of the most important in the Indian Ocean. In this study, four of the most important hawksbill nesting grounds in the Persian Gulf, situated within three Iranian marine protected areas, were surveyed during nesting season,including Nakhiloo, Ommolgorm and Kharko Islands and the mainland beaches of the Naiband Marine-Coastal National Park(NMCNP). We present GIS maps of these key nesting grounds and describe sand texture of key nesting zones, along with conservation recommendations. About 9.2(28.3%) out of 32.5 km of all shores surveyed in this study were used by nesting hawksbill turtles follows: Nakhiloo: 1.4 km(52% of potential nesting area);Ommolgorm: 1.94 km(40%); Kharko: 3.4 km(28%), and NMCNP: 2.46 km(18.9%). The average nesting density was calculated as 131 nests/km at Nakhiloo, 76 nests/km at Ommolgorm, 7 nests/km at Kharko, and 15 nests per km at NMCNP. Highest nesting density was observed in Nakhiloo and Ommolgorm. It is thought that high hawksbill nesting density in these islands seems likely a result of limiting adequate nesting shores rather than the size of population, and also low density in Kharko and NMCNP more related to past and current pressures and low population density. With the exception of Ommolgorm Island, sands at the nesting grounds were well sorted.Grain size indicated that female hawksbill turtles in the Iranian Persian Gulf nest in sands that are generally mixed, with mean grain size ranging from coarse sands(0.4Φ;～0.5–1 mm) to fine sands(2Φ;～0.25 mm). We provide and discuss conservation recommendations and suggestions for future.     

Carbonate Sediment Deposits on the Reef Front Around Oahu, Hawaii

Large sediment deposits on the reef front around Oahu are a possible resource for replenishing eroded beaches. High-resolution subbottom profiles clearly depict the deposits in three study areas: Kailua Bay off the windward coast, Makua to Kahe Point off the leeward coast, and Camp Erdman to Waimea off the north coast. Most of the sediment is in water depths between 20 and 100 m, resting on submerged shelves created during lowstands of sea level. The mapped deposits have a volume of about 4 × 10⁸ m³ in water depths less than 100 m, being thickest off the mouth of channels carved into the modern insular shelf, from which most of the sediment issues. Vibracore samples contain various amounts of sediment of similar size to the sand on Oahu beaches, with the most compatible prospects located off Makaha, Haleiwa, and Camp Erdman, and the least compatible ones located in Kailua Bay. Laboratory tests show a positive correlation of abrasion with Halimeda content: samples from Kailua Bay suffered high amounts of attrition, but others were comparable to tested beach samples. The common gray color of the offshore sediment, aesthetically undesirable for sand on popular tourist beaches, was diminished in the laboratory by soaking in heated hydrogen peroxide.     

Carbonate Sediment Deposits on the Reef Front Around Oahu,Hawaii

Large sediment deposits on the reef front around Oahu are a possible resource for replenishing eroded beaches. High-resolution subbottom profiles clearly depict the deposits in three study areas: Kailua Bay off the windward coast, Makua to Kahe Point off the leeward coast, and Camp Erdman to Waimea off the north coast. Most of the sediment is in water depths between 20 and 100?m, resting on submerged shelves created during lowstands of sea level. The mapped deposits have a volume of about 4?×?10⁸?m³ in water depths less than 100?m, being thickest off the mouth of channels carved into the modern insular shelf, from which most of the sediment issues. Vibracore samples contain various amounts of sediment of similar size to the sand on Oahu beaches, with the most compatible prospects located off Makaha, Haleiwa, and Camp Erdman, and the least compatible ones located in Kailua Bay. Laboratory tests show a positive correlation of abrasion with Halimeda content: samples from Kailua Bay suffered high amounts of attrition, but others were comparable to tested beach samples. The common gray color of the offshore sediment, aesthetically undesirable for sand on popular tourist beaches, was diminished in the laboratory by soaking in heated hydrogen peroxide.     

Effects of Mudstone Particle Content on Shear Strength of a Crushed Sandstone–Mudstone Particle Mixture

The present study focuses on the shear strength, deformation, and particle crushing of sand which is mixed by crushed sandstone and mudstone particles. Two triaxial tests—one for unsaturated specimens and the other for saturated specimens—were performed, along with sieve analysis tests. Results obtained from the triaxial tests indicate that, with the increment of the mudstone particle content by weight, the angle of internal friction decreases, the cohesion increases and then decreases, and both the initial angle of shearing resistance at the atmospheric pressure and decremental angle increase and then decrease. Compared to the unsaturated specimens, the deviator stress or normalized deviator stress of the saturated specimens at the same axial stress may decrease due to the wetting action. Thus, the shear strength of the tested materials may be reduced by the wetting action. Results of sieve analysis tests indicate that the mixing of some mudstone particles into the sandstone particle mixture may reduce the amount of particle crushing, but the wetting action may increase the amount. The amount of the crushed particle may arrive at a minimum of 40% of mudstone particle content by weight.     

Comparison Between Shear Behaviors of Overconsolidated Nakdong River Sandy Silt and Silty Sand

From this research, overconsolidated undrained and drained behaviors of specimens with high sand content were highly dilatant. According to the comparison results of laboratory tests, the deviator stresses of silty sand were greater than sandy silt due to high sand content under increasing OCRs, and both silty sand and sandy silt were presented strain softening tendency after failure under undrained loading. The pore water pressure increased with increasing fines content under increasing OCRs. Silty sand exhibited more dilatancy and increasing shear strength than sandy silt because pore water pressures of silty sand were lower than sandy silt under higher OCRs. In overconsolidated drained tests, silty sand is higher strength than sandy silt because silty sand has a lower volumetric strain and higher deviator stress than sandy silt under increasing OCRs. As the degree of overconsolidation increased, similar behaviors of silty sand and sandy silt observed that volumetric strain decreased to negative values due to dilatancy effect and low-cohesion under current effective confining pressures.     

冲绳海槽北部CSH1岩芯地层与碳酸盐沉积特征

对冲绳海槽北部CSH1岩芯地层及岩芯碳酸盐含量的分析表明,该岩芯记录了氧同位素3期以来的碳酸盐沉积特征,其碳酸盐沉积类型属于“大西洋型”。进一步研究表明,溶解作用对该区域碳酸盐沉积变化的影响作用不大;引起本区域碳酸盐变化的主要因素为非钙质物质的稀释作用,其中陆源物质的稀释作用可能控制了碳酸盐沉积的整体特征,而火山物质则对局部层位的沉积起到了显著作用;钙质生物生产力的变化对碳酸盐沉积的整体变化有一定的影响。     

低围压水平下砂的排水行为(英文)

采用干样沉降法制备样品 ,选用静三轴仪对松砂和密砂样在 10 k Pa至 10 0 k Pa的低围压下的排水行为进行了实验研究 ,并对实验结果作了橡皮膜校正 ,在围压为 10 k Pa的密砂实验中 ,轴向应力的校正值可达到 12 %。实验研究表明低围压下松砂的剪胀性非常明显 ,且存在剪应力极值 ;围压越低 ,松砂和密砂的剪应力极值越小 ,达到最大剪应力所对应的剪应变越小。同时还表明低围压范围内相对密度不同 ,砂的应力应变特性不同 ;此外 ,低围压下砂的内摩擦角高于高围压下的值 ,从而在工程上应重视低围压水平下砂土工程参数的合理选取     

北部湾地区不同相对密度的海砂力学特性分析

为探究相对密度和有效围压对饱和海砂力学特性的影响,利用GDS动态三轴试验仪,对广西北部湾地区海砂开展了一系列固结排水三轴剪切试验,分析了相对密度、有效围压对饱和海砂强度特征、体变特征、割线模量以及摩擦角的影响规律。结果表明：随着围压的减小或相对密度的增大,试样体积应变不断增大,而相对密度或有效围压的增加均会提高试样的峰值强度,有效围压与峰值强度之间呈现良好的线性增长关系。随着围压的减小或相对密度的增大,应力相对软化系数、剪胀系数均不断增大,且有效围压与应力相对软化系数、剪胀系数分别呈线性和半对数线性相关。割线模量随轴向应变的增加整体呈衰减趋势,各试验工况下轴向应变为5%时试样的割线模量相比于轴向应变0.164%衰减了80%~90%。饱和海砂的峰值摩擦角随相对密度的增加而增大,随有效围压的增大而减小,相对密度D_r为50%时有效围压σ_c为50 kPa对应的峰值摩擦角是σ_c为200 kPa的1.098倍。     

Evaluation of State Parameter of Crushable Jeju Sand Using Cone Resistance

This study was performed to evaluate the critical state parameter of crushable Jeju sand and to suggest the relationship between the state parameter and cone resistance of Jeju sand. It is observed from a drained triaxial test that Jeju sand mainly shows contractive behavior due to high void ratio and large compressibility. Although strain localization is not evident, the particle crushing results in a lower void ratio than the critical state void ratio of some Jeju specimens. Critical state parameters of Jeju sand are similar to those of calcareous sands, but significantly larger than those of common sands. The relationship between the normalized cone resistance and state parameter of Jeju sand significantly differs from that of other materials, and this relation appears to be affected by the stress level. This is because the variation of stress level affects the state parameter of Jeju sand more significantly than that of common sand due to the high compressibility of Jeju sand.     

Effect of sand on the vacuum consolidation of dredged slurry

Vacuum preloading is often used to improve the geotechnical properties of dredged slurry. Although the performance of this method has improved with rapidly developing technology, soil columns usually formed on the drainage boundary induce the decrease of permeability around the boundary, thereby limiting the further development of this method. To address this issue, this paper proposes a method for pretreating the slurry combined with sand prior to vacuum consolidation. This method partially replaces the fine particles with sand to reduce the formation of soil columns. Two groups of vacuum preloading tests were performed to investigate the effect of sand content and sand grain size on the vacuum consolidation of dredged slurry. The test results revealed that for a given sand grain size, increasing the sand content of the sand–slurry mixture increased the pore water drainage and accelerated the dissipation of pore water pressure, thereby increasing the vane shear strength. In contrast, for a constant sand content, the samples containing coarse sand exhibited increased pore water drainage and accelerated dissipation of pore water pressure, thereby increasing the vane shear strength of the soil.     

Effect of texture of carbonate soils in South Iran coasts on aggregate crushing

Aggregate crushing is a phenomenon occurring in carbonate soils under shear and compressive loads resulting in settlement of the offshore structures such as piers, bridges, waterfronts, wharfs, and oil and gas extraction platform foundations. Therefore, it is of significant importance to address the above-mentioned issue through a comprehensive study. In the present research, the texture of carbonate soil in south Iran coasts and its effect at high hydrostatic pressure (2?MPa) on aggregate crushing was studied. The physical properties of coastal soils, such as the effective grain size, shape index, and angularity were then characterized to investigate their effect on grain crushing grade. The results showed that the effective grain size, shape index, angularity, and calcium carbonate content are the main parameters affecting the crushing of grains and consequently settlement of marine soils. Based on the above parameters, a relationship is proposed to estimate grain crushing in carbonate soils.     

Behavior of Loose Silty Sand of Chlef River: Effect of Low Plastic Fine Contents and Other Parameters

This article presents a laboratory study of static behavior of silty-sand soils. The objective of this laboratory investigation is to study the effect of initial confining pressures and fines content on the undrained shear strength (known as liquefaction resistance) response, pore pressure, and hydraulic conductivity of sand–silt mixtures. The triaxial tests were conducted on reconstituted saturated silty-sand samples at initial relative density D_r = 15% with fines content ranging from 0 to 50%. All the samples were subjected to a range of initial confining pressures (50, 100, and 200 kPa). The obtained results indicate that the presence of low plastic fines in sand–silt mixture leads to a more compressible soil fabric, and consequently to a significant loss in the soil resistance to liquefaction. The evaluation of the data indicates that the undrained shear strength can be correlated to fines content (F_c), inter-granular void ratio (e_g), and excess of pore pressure (Δu). The undrained shear strength decreases with the decrease of saturated hydraulic conductivity and the increase of fines content for all confining pressures under consideration. There is a relatively high degree of correlation between the peak shear strength (q_peak) and the logarithm of the saturated hydraulic conductivity (k_sat) for all confining pressures.     

Mining Sand on the Continental Shelf of the Atlantic and Gulf Coasts of the U.S.

Essentially all marine mining along the East and Gulf coasts of the U.S. is for sand used in beach nourishment projects. The current minimal commercial production of sand and aggregate may increase as conventional, on-shore sources become exhausted or are lost to competing land use. Studies published in the late 1990s document a history of nearly 900 individual episodes of beach nourishment having a total cost in excess of $2 × 10⁹ with several hundred million cubic meters of sand placed along over 645 km (400 mi) of shoreline. As exemplified by studies in Florida, prospecting for sand for use in beach nourishment can begin before site specific needs are identified. A full prospecting starts with assimilation of pertinent literature, local knowledge, and an understanding of the geologic and geomorphic settings in which suitable deposits of sand or aggregate occur. High-resolution seismic profiling follows to outline the three dimensional extent of the sand bodies. Finally, vibratory cores are collected to verify the interpretation of the seismic data and to provide samples for geotechnical, especially granulometric, analyses. The actual method of production often is determined by the local availability of different dredge types. Because the mining of marine sands disturbs meaningful areas of the sea floor, environmental concerns must be considered. While it generally is assumed that dredged areas will be left barren, it is possible to assess the likely rate of recolonization. The disruption of bottom habitat also can affect feeding and spawning areas for fishes and other organisms. Alteration in local currents and wave transformation processes need to be modeled and their consequences assessed.     

Scleractinian coral communities of Hormuz Island in the Persian Gulf

The abundance and health of scleractinian coral communities of Hormuz Island were investigated. For this purpose, we employed 20 m line intercept transects—12 in the intertidal zone and 15 subtidally to evaluate coral cover and community composition. The estimated dead coral coverage was 6.21%±0.81%, while live coral coverage was 16.93%±1.81%, considered as very poor. Totally, 12 genera were recorded, of which Porites with 11.9%±1.4% live cover was the dominant, while Goniopora had the least cover (0.07%±0.08%). Based on Mann-Whitney U-test, live coral coverage, dead coral coverage, algal coverage, cover of other benthic organisms and abiotic components showed significant univariate differences between zones (p<0.05). The Spearman correlation test between the abundance of biotic and abiotic components indicated significant negative correlation of live coral and sand with zoantharian and significant positive correlation of algae and other benthic organisms with rubble. The reef health indices used for the corals indicated that, in general, the environmental conditions were not suitable, which could be attributed to both natural and anthropogenic factors, the most important of which was zoantharian’ overgrowth on the scleractinian corals in this region.     

辽东湾S2冰侧限剪切强度的试验研究

利用试验方法系统地研究了辽东湾S2型海冰侧限剪切强度随剪切应变速率、加载方向、法向应力、温度和冰内孔隙率的变化规律。介绍了S2型海冰各向异性特点及剪切应变速率对剪切破坏方式的效应和韧脆破坏转变的条件。分析了不同加载方向海冰峰值剪切强度的差异 ,获得 - 6 2℃温度下S2冰内摩擦角和内聚力分别为 42°和 70 0kPa。利用统计分析给出峰值剪切强度与冰温和孔隙率的试验关系     

Monotonic and cyclic behaviors of loose anisotropically consolidated calcareous sand in torsional shear tests

ABSTRACT

The behavior of loose anisotropically consolidated calcareous sand obtained from an island in the South China Sea was investigated under undrained monotonic and cyclic loading in a hollow cylinder torsional apparatus. The tests were conducted on specimens which consolidated under various initial effective confining pressures and consolidation stress ratios. The monotonic test results show that the failure and phase transformation line are essentially independent of the consolidation conditions, while the initial contractive tendency of the specimens decreases with an increasing consolidation stress ratio. During monotonic loading of the anisotropically consolidated specimens, a same major principal stress direction is observed at the constant stress ratio lines up to the phase transformation line, irrespective of initial effective confining pressure. The cyclic strength of the sand increases with an increasing consolidation stress ratio. Moreover, a pronounced stress dependence is observed in the sand with higher consolidation stress ratio. During cyclic loading, the generated excess pore water pressure presents considerable fluctuations. The normalized terminal excess pore water pressure is described as a function of consolidation stress ratio. The tests show that the particle shape, rather than particle crushing, plays an important role in the monotonic and cyclic behaviors of the calcareous sand.     

Intertidal gastropod assemblages shaped by key environmental variables across the northern Persian Gulf and the Gulf of Omanss

Variations in environmental factors can alter the species distribution pattern in intertidal rocky shores. The Persian Gulf (PG) and the Gulf of Oman (GO) vary substantially with respect to environmental and oceanographic conditions. The abundance and biodiversity of intertidal rocky gastropods in five locations across the northern PG and the GO were compared, and the environmental variables underlying the distribution pattern of these organisms were investigated. A total of 67 gastropod species were identified. The largest average density (294 ind./m²) and diversity (N = 43) for gastropods occurred in the Hotel Lipar station (LIP) located in Chabahar Bay in the GO. Clypeomorus bifasciata (107.43 ind./m²) followed by Cerithium caeruleum (94.67 ind./m²) were the most abundant species. Planaxis sulcatus and Siphonaria spp. occurred in all locations during both sampling occasions. Species richness and abundance of gastropods showed significant differences between LIP and remaining locations. A significant difference was found in assemblage structure across locations. In general, the species richness and density in the locations at GO were significantly larger than those locations in the PG, suggesting that the harsh environmental condition in the PG might be the forcing factor for this diminish. Distinct grouping was observed in both assemblage structure and species composition between locations in the PG and the GO. The spatial and temporal distribution patterns of gastropods assemblages were significantly correlated with variation in salinity and substrate rugosity.