Determination of Rare Earth Elements, Sc, Y, Zr, Ba, Hf and Th in Geological Samples by ICP-MS after Tm Addition and Alkaline Fusion

We present a revised method for the determination of concentrations of rare earth (REE) and other trace elements (Y, Sc, Zr, Ba, Hf, Th) in geological samples. Our analytical procedure involves sample digestion using alkaline fusion (NaOH-Na₂O₂) after addition of a Tm spike, co-precipitation on iron hydroxides, and measurement by sector field-inductively coupled plasma-mass spectrometry (SF-ICP-MS). The procedure was tested successfully for various rock types (i.e., basalt, ultramafic rock, sediment, soil, granite), including rocks with low trace element abundances (sub ng g⁻¹). Results obtained for a series of nine geological reference materials (BIR-1, BCR-2, UB-N, JP-1, AC-E, MA-N, MAG-1, GSMS-2, GSS-4) are in reasonable agreement with published working values.     

Determination of Trace Element Mass Fractions in Ultramafic Rocks by HR‐ICP‐MS: A Combined Approach Using a Direct Digestion/Dilution Method and Preconcentration by Coprecipitation

A procedure is described for the determination of thirty‐seven minor and trace elements (LILE, REE, HFSE, U, Th, Pb, transition elements and Ga) in ultramafic rocks. After Tm addition and acid sample digestion, compositions were determined both following a direct digestion/dilution method (without element separation) and after a preconcentration procedure using a double coprecipitation process. Four ultramafic reference materials were investigated to test and validate our procedure (UB‐N, MGL‐GAS [GeoPT12], JP‐1 and DTS‐2B). Results obtained following the preconcentration procedure are in good agreement with previously published work on REE, HFSE, U, Th, Pb and some of the transition elements (Sc, Ti, V). This procedure has two major advantages: (a) it avoids any matrix effect resulting from the high Mg content of peridotite, and (b) it allows the preconcentration of a larger trace element set than with previous methods. Other elements (LILE, other transition elements Cr, Mn, Co, Ni, Cu, Zn, as well as Ga) were not fully coprecipitated with the preconcentration method and could only be accurately determined through the direct digestion/dilution method.     

Chemical Characterisation of the USGS Reference Glasses GSA-1G, GSC-1G, GSD-1G, GSE-1G, BCR-2G, BHVO-2G and BIR-1G Using EPMA, ID-TIMS, ID-ICP-MS and LA-ICP-MS

The USGS reference glasses GSA-1G, GSC-1G, GSD-1G, GSE-1G, BCR-2G, BHVO-2G and BIR-1G were investigated by different analytical techniques. All these materials have a geological (basaltic) matrix and are therefore useful in igneous geochemistry as matrix-matched reference materials for microanalytical techniques. The new GS glasses have trace elements in groups at concentration levels of about < 0.01, 5, 50 and 500 μg g^-1. Their major element compositions have been determined by EPMA, and trace elements have been analysed by LA-ICP-MS and two isotope dilution techniques using TIMS and ICP-MS. EPMA and LA-ICP-MS analyses indicated that the USGS reference glasses are homogeneous at the μm to mm scale with respect to major (variations < 1-2%) and most trace elements (variations 1-4%). Trace element data obtained from the different analytical techniques agreed within an uncertainty of 1-5%, indicating that between method results are comparable. Therefore, the preliminary working values for the four USGS GS glasses calculated from these data have a low level of uncertainty.     

Determination of Trace Elements in Geological Reference Materials G‐3, GSP‐2 and SGD‐1a by Low‐Dilution Glass Bead Digestion and ICP‐MS

We present a revised alkali fusion method for the determination of trace elements in geological samples. Our procedure is based on simple acid digestion of powdered low‐dilution (flux : sample ≈ 2 : 1) glass beads where large sample dilution demanded by high total dissolved solids, a main drawback of conventional alkali fusion, could be circumvented. Three geological reference materials (G‐3 granite, GSP‐2 granodiorite and SGD‐1a gabbro) decomposed by this technique and routine tabletop acid digestion were analysed for thirty trace elements using a quadrupole ICP‐MS. Results by conventional acid digestion distinctly showed poor recoveries of Zr, Hf and rare earth elements due to incomplete dissolution of resistant minerals. On the other hand, results obtained by our method were in reasonable agreement with reference data for most analytes, indicating that refractory minerals were efficiently dissolved and volatile loss was insignificant.     

利用同一化学流程分析地质样品中的铂族元素含量和铼-锇同位素组成

报道了利用一次溶样和同一化学流程分离富集地质样品中铂族元素(Pt、Pd、Os、Ir和Ru)和Re的方法.该化学流程包括以下几个步骤:(1) Carius管溶样法分解岩石样品中富集铂族元素的矿物;(2)四氯化碳萃取法分离出Os;(3)微蒸馏法进一步纯化Os;(4)阳离子交换树脂法将铂族元素(Pt、Pd、Ir和Ru)以及R...     

Determination of Rare Earth Elements, Y, Th, Zr, Hf, Nb and Ta in Geological Reference Materials G-2, G-3, SCo-1 and WGB-1 by Sodium Peroxide Sintering and Inductively Coupled Plasma-Mass Spectrometry

Data are reported for rare earth elements (REE), Y, Th, Zr, Hf, Nb and Ta in four geological reference materials using sodium peroxide (Na₂O₂) sintering and inductively coupled plasma-mass spectrometry. The described procedure was used by students during their thesis work. A compilation of their reference material data acquired over one year of laboratory work demonstrates the ease and reliability of the method and the high reproducibility of the analytical results. Relative standard deviations of up to thirty six measurements of one reference material were lower than 5% for Y and the REE. Reproduciblities of Zr, Hf, Nb, Ta and Th were higher at between 5% and 10%, and can be attributed to the inhomogeneous distribution of zircon and other trace mineral phases and uncorrected drift effects. The concentration data are compared to reference and literature values and demonstrate that the procedure is also accurate. New data on G-3 show some systematic deviations from G-2, which are statistically significant.     

Determination of Ga,Ge, Mo,Ag, Cd,In, Sn,Sb, W,Tl and Bi in USGS Whole‐Rock Reference Materials by Standard Addition ICP‐MS

A procedure for determining a wide range of chalcophile and siderophile elements in typical crustal rocks using standard addition and ICP‐SFMS (inductively coupled plasma sector field mass spectrometry) is presented. New results for Ga, Ge, Mo, Ag, Cd, In, Sn, Sb, W, Tl and Bi abundances in USGS whole‐rock reference materials AGV‐2, BHVO‐1, BIR‐1, G‐2, GSP‐1 and W‐2 are reported using this analytical procedure. Intermediate precision of means based on multiple dissolved aliquots of each USGS reference material was 10% RSD or better for Ga, Ge, In and Sn in all, and similarly good for Ag, Cd, Sb, Tl and Bi in most reference materials. Poorer intermediate precision of Mo and W measurements in several reference materials is probably due to higher analytical blanks on these elements and powder heterogeneity due to a sulfide‐related nugget effect in the specific case of Mo in GSP‐1. Results for all elements fell within the range of available published data with the exception of Ag, which yielded systematically higher concentrations than found in the literature for five of the six reference materials, likely reflecting interference from unresolved polyatomic species.     

New Progress on Certified Reference Materials for Platinum-Group Elements: IGGE GPt-8, GPt-9 and GPt-10

Three new certified reference materials (CRM), certified for the platinum-group elements (PGE), GPt-8, GPt-9 and GPt-10 were developed based on the previous CRMs IGGE GPt-1 to GPt-7. The PGE concentration of GPt-8 is about 1 ng g^-1. GPt-9 and GPt-10 are ore samples with PGE concentrations of more than 1 μg g^-1. A multi-laboratory collaborative analysis scheme was adopted in the certification procedure, in which nine highly-experienced institutes and laboratories participated. The samples were analysed for the six platinum-group elements by nickel sulfide mini fire assay, with Te coprecipitation, and were determined by ICP-MS. Osmium was determined by isotope dilution.     

Laser Ablation and Solution ICP-MS Determination of Rare Earth Elements in USGS BIR-1G, BHVO-2G and BCR-2G Glass Reference Materials

Data are reported for rare earth elements (REE) in three geological glass reference materials (BIR-1G, BHVO-2G and BCR-2G) using a UV (266 nm) laser ablation ICP-MS system and the classical (HF-HClO₄) acid decomposition method, followed by conventional nebulisation ICP-MS. External calibration of laser ablation analyses was performed using NIST SRM reference materials with internal standardisation using ²⁹Si and ⁴⁴Ca. Replicate analyses of reference basaltic glasses yielded an analytical precision of 1-5% (RSD) for all the elements by solution ICP-MS and 1-8% (RSD) by laser ablation ICP-MS. The relative differences between the REE concentrations measured by solution and laser ablation ICP-MS compared with the reference values were generally less than 11 % for most elements. The largest deviations occurred for La determined by solution ICP-MS in BIR-1G. The results of both solution and laser ablation ICP-MS agreed well, generally better than 7%, with the exception of La, Pr and Sm in BIR-1G. The measured REE laser ablation data for BIR-1G, BHVO-2G and BCR-2G agreed with the previously published data on these basaltic reference glasses, within a range of 0-10% for most elements. No significant influences were observed for the predicted spectral interferences on some REE isotopes in the analysis of basaltic glasses.     

The Preparation and Characterisation of Two New Geological Survey of Japan Geochemical Reference Materials: Copper ore JCu-1 and Zinc ore JZn-1

Two new geochemical reference materials, copper ore JCu-1 and zinc ore JZn-1 have been prepared by the Geological Survey of Japan (GSJ) for the determination of major and minor elements and isotopic compositions. JCu-1 is a sample of Cu-bearing sulfide ore typical of the Kamaishi mine in Iwate Prefecture, Japan, and is composed mainly of hedenbergite, chalcopyrite, quartz and calcite. Pyrrhotite, magnetite and actinolitic amphibole were also commonly found. The Zn-rich ore, JZn-1 is a crude ore from the Kamioka Pb-Zn mine in Gifu Prefecture, Japan. The sample consists of hedenbergite, quartz, calcite, sphalerite and epidote as main crystalline phase. Homogeneity test results showed that all studied constituents including ore elements such as Cu, Pb and Zn can be considered to be homogeneously distributed. Provisional collaborative analyses were carried out in ten laboratories, and the data were evaluated using a robust statistical method using z-scores. Recommended values for a number of major elements including TiO₂, Al₂O₃, MnO, MgO, CaO, Na₂O, K₂O, Fe (total), Zn, Cu and Pb were established. In addition, information values for eighteen major, minor and trace elements are presented to support future collaborative analyses.     

电感耦合等离子体发射光谱法测定富镁铁橄榄岩类矿石中铜镍铁和氧化镁

样品经氢氟酸-盐酸-硝酸-高氯酸混合酸一次加入冷浸直接溶解,在5%(体积分数)的盐酸介质中,用电感耦合等离子体发射光谱法测定富镁铁橄榄岩类矿石中的铜、镍、铁、氧化镁,克服了传统分析方法操作繁琐、周期长、成本高,而过程难以控制等缺点。方法检出限为铜2.0μg/g,镍3.0μg/g,铁10μg/g,氧化镁20μg/g;精密度(RSD,n=12)为0.8%～4.1%。经国家一级标准物质分析验证,测定值与标准值吻合,结果准确可靠。对于富镁铁岩类矿石中含量较高的硫化物的测定,采用一次加混合酸冷浸除硫后,再加热分解样品,结果令人满意;其中含量较高的铁和氧化镁,采用分取稀释测定,减小基体干扰。建立的方法样品处理程序简单快速,线性范围宽,分析重现性好,适用于地质部门批量样品的分析。     

电感耦合等离子体质谱法同时测定铜铅锌矿石中微量元素镓铟铊钨钼的干扰消除

对电感耦合等离子体质谱法同时测定铜矿石、铅矿石和锌矿石中镓、铟、铊、钨和钼量时,基体效应和主量元素铜、铅、锌对测量的干扰情况及可能的消除方法进行试验,结果表明,溶液中共存小于200μg/mL锌对上述微量元素的测量没有干扰;溶液中共存大于50μg/mL的铜对镓、铟、铊、钨、钼的测量有负干扰,共存大于100μg/mL铅对钨的测量有正干扰,对钼的测量有负干扰,采用钪、铼、镧混合内标或基体匹配可以消除这些干扰;溶液中共存大于20μg/mL的铅对铊的测量有正干扰,选择203Tl为测量质量数,可使耐受铅的干扰浓度提高到50μg/mL,铅对铊测量的干扰可以采用校正系数法或基体匹配进行校正或消除。     

Presolar nanodiamonds: faster, cleaner, and limits on platinum-HL

We have developed a procedure that allows extraction of clean nanodiamond samples from primitive meteorites for isotopic analyses of trace elements on a timescale of just a week. This procedure includes microwave digestion and optimization of existing isolation techniques for further purification. Abundances of trace elements that are difficult to dissolve using standard procedures (e.g., Ir) are lower in the diamond residues prepared using the new technique. Accelerator mass spectrometry (AMS) was explored as a means for isotopic measurements. Results obtained on diamond fractions from Allende and Murchison show the need for suitable matrix-adjusted standards to correct for fractionation effects; nevertheless they allow putting an upper limit on the abundance of ¹⁹⁸Pt-H in nanodiamonds of ∼1 × 10¹⁴ atoms/g. This limit is on the order of what can be expected from predictions of competing nucleosynthesis models and extrapolation of the apparently mass dependent abundance trend of the associated noble gases.Unfortunately, and unexpectedly, presolar silicon carbide is almost quantitatively dissolved during microwave digestion with HCl/HF/HNO₃. Re-evaluation of the standard extraction technique, however, shows that it also may lead to severe loss of fine-grained SiC, a fact not commonly appreciated. A lower limit to SiC abundance in Murchison is 20 ppm, and previous conclusions that Murchison SiC is unusually coarse-grained compared to SiC in other primitive meteorites seem not to be warranted. Graphite and silicon nitride may survive and possibly can be separated after this step as suggested by a simulation experiment using terrestrial analog material, but the detailed behavior of meteoritic graphite requires further study.     

电感耦合等离子体发射光谱法同时测定钒钛磁铁矿中钒钛钴镍

钒钛磁铁矿样品经过氧化钠熔融,盐酸提取,溶液分取稀释后用电感耦合等离子体发射光谱法同时测定其中的V2O5、TiO2、Co、Ni。实验确定过氧化钠的用量为1.5 g,盐酸的用量为10 mL,选择干扰元素较少和背景干扰较小的V、Ti、Co、Ni分析谱线分别为292.4 nm、334.9 nm、230.7 nm、231.6 nm,在稀释因子为10(总稀释因子5000)的条件下进行分析,方法检出限为0.05～0.17μg/g。用国家一级钒钛磁铁矿标准物质GBW 07225(原矿)、钒钛磁铁矿标准物质GBW 07226a(精矿)、钒钛磁铁矿标准物质GBW 07227(尾矿)验证方法精密度和准确度,方法精密度(RSD,n=12)为0.41%～1.91%;除含量较低的Ni和Co外,相对误差(RE,n=4)均小于5%。通过安装氩气加湿器有效地解决了盐分较大带来的影响,在标准系列中加入等量空白溶液,保持基体与试样一致,消除了基体效应。方法分解样品彻底完全,分析流程简单,易于掌握,一次熔样可以同时测定多种元素,可适用于大批量样品分析。     

Determination of Trace Elements in Calcite Using Solution and Laser Ablation ICP-MS: Calibration to NIST SRM Glass and USGS MACS Carbonate, and Application to Real Landfill Calcite

We report new data on the trace element concentrations of Mg, Cr, Mn, Co, Ni, Cu, Zn, Sr, Cd, Ba, La, Ce, Nd, Pb and U in USGS carbonate reference materials (MACS-1 and MACS-2) and compare solution ICP-MS and LA-ICP-MS trace element determinations on landfill calcites using calibration to different reference materials (MACS-1 and MACS-2 carbonate and NIST SRM 612 glass). Very good agreement (differences below 10% relative) was found between laser ablation and solution ICP-MS data for MACS-1 with higher concentrations of trace elements (values between 100 and 150 μg g⁻¹), with the exception of Cu and Zn. Similarly good agreement was found for MACS-2 with lower trace element concentrations (units to tens of μg g⁻¹), with the exception of Cr, Co and Zn. The MACS-1 reference material for calibration of LA-ICP-MS was found to be extremely useful for in situ determination of trace elements in real-world carbonate samples (landfill calcites), especially those present in calcite in higher concentrations (Mn, Sr, Ba; < 5% RSD). Less accurate determinations were generally obtained for trace elements present at low concentrations (∼ units of μg g⁻¹). In addition, good agreement was observed between the instrument calibration to MACS and NIST SRM 612 glass for in situ measurements of trace elements in landfill calcites K-2, K-3 and K-4 (differences below 15% relative for most elements). Thus, the application of MACS carbonate reference materials is promising and points to the need for the development of new carbonate reference materials for laser ablation ICP-MS.     

Rapid Determination of Trace Element Compositions in Peridotites by LA‐ICP‐MS Using an Albite Fusion Method

A rapid sample preparation procedure is described to determine trace element compositions of peridotites using LA‐ICP‐MS. Peridotite powders were fused with albite in a molybdenum–graphite assembly to obtain homogeneous glasses. Best conditions for the fusion procedure (heating at 1500–1550 °C for 10–15 min with a sample‐to‐flux ratio of 1:2) were constrained with melting experiments on two USGS reference materials, PCC‐1 and DTS‐2B. Mass fractions of first series transition elements, Ba and Pb, in quenched glasses of PCC‐1 and DTS‐2B are consistent with published data within 10% RSD. Three spinel peridotite xenoliths from eastern China were analysed following both our method and conventional solution ICP‐MS. Compared with solution ICP‐MS, the relative deviations of our method for most elements were within 10%, while for the REE, Ta, Pb, Th and U, the relative deviations were within 20%. In particular, volatile elements (e.g., Pb and Zn) are retained in the glass. Compared with conventional wet chemistry digestion, our method is faster. Additional advantages are complete sample fusion, especially useful for samples with acid‐resistant minerals (spinel and rutile), and long‐term conservation of glasses allowing unlimited repeated measurements with microbeam techniques. The same approach can be used for analyses of other mantle rocks, such as eclogites and pyroxenites.     

Single Column Sequential Extraction of Ra,Nd, Th,Pa and U from a Natural Sample

A new procedure allowing the sequential extraction of Ra, Nd, Th, Pa and U from the same initial natural sample (sea or river waters, particles, sediments, rocks) is proposed. Extraction recoveries were better than 90%. Procedural blanks ranged from 80 pg (for Nd) to below 1 fg, the detection limit of the MC‐ICP‐MS used (for Pa); all were negligible compared with the amounts of elements currently determined. Based on classical anionic resins attached to a peristaltic pump allowing precise flow rate control, this procedure allowed a consequent reduction of the sample size, which improved the sampling resolution and reduced the sampling cost. It also ensured a better consistency of the samples for the five tracers.     

High-Precision Trace Element Data for the USGS Reference Materials BCR-1, BCR-2, BHVO-1, BHVO-2, AGV-1, AGV-2, DTS-1, DTS-2, GSP-1 and GSP-2 by ID-TIMS and MIC-SSMS

Different batches of the new US Geological Survey (USGS) reference materials (RMs) BCR-2, BHVO-2, AGV-2, DTS-2 and GSP-2 and the original USGS RMs BCR-1, BHVO-1, AGV-1, DTS-1 and GSP-1 have been analysed by isotope dilution using thermal ionisation mass spectrometry (ID-TIMS) and by multi-ion counting spark source mass spectrometry (MIC-SSMS). The concentrations of K, Rb, Sr, Ba and the rare earth elements were determined with overall analytical uncertainties of better than 1% (ID-TIMS) and 3% (MIC-SSMS). The analyses of different aliquots and batches of BCR-2, BHVO-2, AGV-2 and GSP-2, respectively, agree within 1%, i.e. approximately the analytical uncertainties of the data. This indicates an homogeneous distribution of the trace elements in these RMs. Differences in element concentrations of up to 17% in different aliquots of the depleted RM DTS-2 are outside the analytical uncertainty of our data. They may be attributed to a slightly heterogeneous distribution of trace elements in this dunite sample. Our trace element data for BCR-2, BHVO-2, AGV-2 and GSP-2 agree within about 3% with preliminary reference values published by the USGS. They also agree within 1-6% with those of the original RMs BCR-1, BHVO-1, AGV-1 and GSP-1. Large compositional differences are found between DTS-2 and DTS-1, where the concentrations of K, Rb, Sr and the light REE differ by factors of 2 to 24.     

A 3D composite finite element used to model a vertical drain and its surrounding remoulded soil

This work addresses an enrichment technique for the three-dimensional (3D) finite element (FE) analysis of a vertical drain foundation because (1) 1D and 2D simulations are insufficient to integrally describe the consolidation behaviour and (2) drains are small both in spacing and size, resulting in enormous computational costs for a traditional 3D FE analysis. Based on the idea of the semi-analytical finite element method (FEM), which combines general FEM with the high accuracy of a closed-form solution, a new spatial element that contains a drain well and its neighbouring smear zone is presented. This new combined element is depicted by eight global independent nodes and two local dependent nodes, and a classical analytical theory is introduced to set up the relationship between the two kinds of nodes. Because permeability diversity between the drain and the smear zone is considered, both the effects of smearing and well resistance are taken into account with the composite element method (CEM). A detailed derivation of the CEM is performed using the weighted residual method. The accuracy of the proposed method is validated with a totally penetrating, single-drain ground analysis for seven calculation conditions. Additionally, the proposed CEM saves 1/4–1/2 mesh elements and helps to avoid slender elements for the FEM analysis of the drained foundation.     

微波消解-电感耦合等离子体发射光谱法同时测定白云石中铁铝钙镁钾钠硫

采用微波消解白云石样品，电感耦合等离子体发射光谱法测定其中铁、铝、钙、镁、钾、钠、硫的氧化物，对微波消解条件和等离子体发射光谱仪的工作条件进行了选择，克服了常规化学分析方法步骤繁琐、耗时长、工作量大的不足。利用所建立的方法快速分析了白云石中铁、铝、钙、镁、钾、钠、硫的含量，结果与标准值或化学法相符，10次测定的相对标准偏差（RSD）7种元素均小于1％，可以满足生产和科研的要求。