The Astrakhan Arch of the Pricaspian basin: Geothermal analysis and modelling

The Astrakhan Arch (ASAR) region contains one of the largest sub‐salt carbonate structures of the Pricaspian salt basin (located to the northwest of the Caspian Sea), where prospects for hydrocarbon generation and accumulation in the Devonian to Carboniferous deposits are considered to be high. We evaluate the regional vertical temperature gradient within stratigraphic units based on the analysis of 34 boreholes drilled in the region. To show that the thermal gradient is altered in the vicinity of salt diapirs, we study measured temperatures in six deep boreholes. We develop a three‐dimensional geothermal model of the ASAR region constrained by temperature measurements, seismic stratigraphic and lithological data. The temperatures of the sub‐salt sediments predicted by the geothermal model range from about 100 °C to 200 °C and are consistent with the temperatures obtained from the analysis of vitrinite reflectivity and from previous two‐dimensional geothermal models. Temperature anomalies are positive in the uppermost portions of salt diapirs as well as within the salt‐withdrawal basins at the depth of 3.5 km depth and are negative beneath the diapirs. Two areas of positive temperature anomalies in the sub‐salt sediments are likely to be associated with the deep withdrawal basins above and with the general uplift of salt/sub‐salt interface in the southern part of the study region. This implies an enhancement of thermal maturity of any organically rich source rocks within these areas. The surface heat flux in the model varies laterally from about 40 to 55 mW m^?2. These variations in the heat flux are likely to be associated with structural heterogeneities of the sedimentary rocks and with the presence of salt diapirs. The results of our modelling support the hypothesis of oil and gas condensate generation in the Upper Carboniferous to Middle Devonian sediments of the ASAR region.     

Fluvial architecture in actively deforming salt basins: Chinle Formation,Paradox Basin,Utah

Determining the response of fluvial systems to syn‐sedimentary halokinesis is important for reconstructing the palaeogeography of salt basins, determining the history of salt movement and predicting development and architecture of sandstone bodies for subsurface fluid extraction. To assess both the influence of salt movement on fluvial system development and the use of lithostratigraphic correlation schemes in salt basins we have analysed the Triassic Chinle Formation in the Paradox Basin, Utah. Results indicate that sandstone body development proximal to salt bodies should be considered at two scales: intra‐ (local) and inter‐ (regional) mini‐basin scale. At the intra‐mini basin or local scale, conformable packages of up to 12 m deep meandering fluvial channel deposits and associated overbank deposits are developed, which may thin, pinch‐out or become truncated towards salt highs. When traced down the axis of a mini‐basin, individual stories extend for a few hundred metres, and form part of amalgamated channel‐belt packages up to 60 m thick that can be traced for at least 25 km parallel to palaeoflow. Where salt movement outpaces sediment accumulation, progressive low angle unconformities are developed along the flanks of salt highs. Significantly, in mini‐basins with high sand supply, sandstone bodies are present across salt highs where they show increased amalgamation, decrease in thickness due to truncation and no change in internal sandstone body character. At inter mini‐basin or regional scale, spatial and temporal variations in accommodation space generated by differential salt movement strongly influence facies distributions and facies correlation lengths. Broad lithostratigraphic packages (5–50 m thick) can be correlated within mini‐basins, but correlation of these units between adjacent mini‐basins is problematic. Knowledge of fluvial system development at a regional scale is critical as, fluvial sediment distribution is focussed by topography generated by growing salt bodies, such that adjacent mini‐basins can have significant differences in sandstone body thickness, distribution and lateral extent. The observations from the Chinle Formation indicate that lithostratigraphic‐based correlation schemes can only be applied within mini‐basins and cannot be used to correlate between adjacent mini‐basins or across a salt mini‐basin province. The key to predicting sandstone body development is an understanding of the timing of salt movement and reconstructing fluvial drainage system development.     

Deep vs. shallow controlling factors of the crustal thermal field – insights from 3D modelling of the Beaufort‐Mackenzie Basin (Arctic Canada)

Significant lateral variations in observed temperatures in the Beaufort‐Mackenzie Basin raise the question on the temperature‐controlling factors. Based on the structural configuration of the sediments and underlying crust in the area, we calculate the steady‐state 3D conductive thermal field. Integrated data include the base of the relic permafrost layer representing the 0 °C‐isotherm, public‐domain temperature data (from 227 wells) and thermal conductivity data. For >75% of the wells the predicted temperatures deviate by <10 K from the observed temperatures, which validates the overall model setup and adopted thermal properties. One important trend reproduced by the model is a decrease in temperatures from the western to the eastern basin. While in the west, a maximum temperature of 185 °C is reached at 5000 m below sea level, in the east the maximum temperature is 138 °C. The main cause for this pattern lies in lateral variations in thermal conductivity indicating differences in the shale and sand contents of the different juxtaposed sedimentary units. North‐to‐south temperature trends reveal the superposition of deep and shallow effects. At the southern margin, where the insulating effect of the low‐conductive sediments is missing, temperatures are lowest. Farther north, where the sub‐sedimentary continental crust is thick enough to produce considerable heat and a thick pile of sediments efficiently stores heat, temperatures tend to be highest. Temperatures decrease again towards the northernmost distal parts of the basin, where thinned continental and oceanic crust produce less radiogenic heat. Wells with larger deviations of the purely conductive model from the temperature observations (>15 K at 10% of the wells) and their basin‐wide pattern of misfit tendency (too cold vs. too warm temperature predictions) point to a locally restricted coupling of heat transport to groundwater flow.     

Mid-Palaeocene palaeogeography of the eastern North Sea basin: integrating geological evidence and 3D geodynamic modelling

The Mid‐Palaeocene palaeogeography of Denmark and the surrounding areas have been reconstructed on the basis of published geological data integrated with 3D geodynamic modelling. The use of numerical modelling enables quantitative testing of scenarios based on geological input alone and thus helps constrain likely palaeo‐water depths in areas where the geological data are inconclusive or incomplete. The interpretation of large‐scale erosional valleys and small‐scale circular depressions at the Mid‐Palaeocene Top Chalk surface in the Norwegian–Danish basin as either submarine or subaerial features is enigmatic and has strong implications for palaeogeographical reconstructions of the eastern North Sea basin. A 3D thermo‐mechanical model is employed in order to constrain the likely palaeo‐water depths of the eastern North Sea basin during the Palaeocene. The model treats the lithosphere as an elasto‐visco‐plastic continuum and models the lithospheric response to the regional stress field and thermal structure. The model includes the effects of sea‐level change, sedimentation and erosion, from the Mid Cretaceous to the present. Modelling results reproduce to first order geological data such as present sediment isopachs and palaeo‐water depths. It is concluded that the Mid Palaeocene water depths in the Norwegian–Danish basin were about 250 m. The erosional valleys and circular depressions at the top of the Upper Cretaceous‐Danian Chalk Group are thus interpreted to have formed in relatively deep water rather than due to subaerial exposure. Likely interpretations of the structures are therefore submarine valleys and pockmarks.     

Anomalous passive subsidence of deep‐water sedimentary basins: a prearc basin example,southern New Caledonia Trough and Taranaki Basin,New Zealand

Stratigraphic data from petroleum wells and seismic reflection analysis reveal two distinct episodes of subsidence in the southern New Caledonia Trough and deep‐water Taranaki Basin. Tectonic subsidence of ~2.5 km was related to Cretaceous rift faulting and post‐rift thermal subsidence, and ~1.5 km of anomalous passive tectonic subsidence occurred during Cenozoic time. Pure‐shear stretching by factors of up to 2 is estimated for the first phase of subsidence from the exponential decay of post‐rift subsidence. The second subsidence event occured ~40 Ma after rifting ceased, and was not associated with faulting in the upper crust. Eocene subsidence patterns indicate northward tilting of the basin, followed by rapid regional subsidence during the Oligocene and Early Miocene. The resulting basin is 300–500 km wide and over 2000 km long, includes part of Taranaki Basin, and is not easily explained by any classic model of lithosphere deformation or cooling. The spatial scale of the basin, paucity of Cenozoic crustal faulting, and magnitudes of subsidence suggest a regional process that acted from below, probably originating within the upper mantle. This process was likely associated with inception of nearby Australia‐Pacific plate convergence, which ultimately formed the Tonga‐Kermadec subduction zone. Our study demonstrates that shallow‐water environments persisted for longer and their associated sedimentary sequences are hence thicker than would be predicted by any rift basin model that produces such large values of subsidence and an equivalent water depth. We suggest that convective processes within the upper mantle can influence the sedimentary facies distribution and thermal architecture of deep‐water basins, and that not all deep‐water basins are simply the evolved products of the same processes that produce shallow‐water sedimentary basins. This may be particularly true during the inception of subduction zones, and we suggest the term ‘prearc’ basin to describe this tectonic setting.     

Constraining basin thermal history and petroleum generation using palaeoclimate data in the Piceance Basin,Colorado

Careful assessment of basin thermal history is critical to modelling petroleum generation in sedimentary basins. In this paper, we propose a novel approach to constraining basin thermal history using palaeoclimate temperature reconstructions and study its impact on estimating source rock maturation and hydrocarbon generation in a terrestrial sedimentary basin. We compile mean annual temperature (MAT) estimates from macroflora assemblage data to capture past surface temperature variation for the Piceance Basin, a high‐elevation, intermontane, sedimentary basin in Colorado, USA. We use macroflora assemblage data to constrain the temporal evolution of the upper thermal boundary condition and to capture the temperature change with basin uplift. We compare these results with the case where the upper thermal boundary condition is based solely upon a simplified latitudinal temperature estimate with no elevation effect. For illustrative purposes, 2 one‐dimensional (1‐D) basin models are constructed using these two different upper thermal boundary condition scenarios and additional geological and geochemical input data in order to investigate the impact of the upper thermal boundary condition on petroleum source rock maturation and kerogen transformation processes. The basin model predictions indicate that the source rock maturation is very sensitive to the upper thermal boundary condition for terrestrial basins with variable elevation histories. The models show substantial differences in source rock maturation histories and kerogen transformation ratio over geologic time. Vitrinite reflectance decreases by 0.21%Ro, source rock transformation ratio decreases 10.5% and hydrocarbon mass generation decreases by 16% using the macroflora assemblage data. In addition, we find that by using the macroflora assemblage data, the modelled depth profiles of vitrinite reflectance better matches present‐day measurements. These differences demonstrate the importance of constraining thermal boundary conditions, which can be addressed by palaeotemperature reconstructions from palaeoclimate and palaeo‐elevation data for many terrestrial basins. Although the palaeotemperature reconstruction compiled for this study is region specific, the approach presented here is generally applicable for other terrestrial basin settings, particularly basins which have undergone substantial subaerial elevation change over time.     

Salt thickness and composition influence rift structural style,northern North Sea,offshore Norway

“Salt” giants are typically halite‐dominated, although they invariably contain other evaporite (e.g. anhydrite, bittern salts) and non‐evaporite (e.g. carbonate, clastic) rocks. Rheological differences between these rocks mean they impact or respond to rift‐related, upper crustal deformation in different ways. Our understanding of basin‐scale lithology variations in ancient salt giants, what controls this and how this impacts later rift‐related deformation, is poor, principally due to a lack of subsurface datasets of sufficiently regional extent. Here we use 2D seismic reflection and borehole data from offshore Norway to map compositional variations within the Zechstein Supergroup (ZSG) (Lopingian), relating this to the structural styles developed during Middle Jurassic‐to‐Early Cretaceous rifting. Based on the proportion of halite, we identify and map four intrasalt depositional zones (sensu Clark et al., Journal of the Geological Society, 1998, 155, 663) offshore Norway. We show that, at the basin margins, the ZSG is carbonate‐dominated, whereas towards the basin centre, it becomes increasingly halite‐dominated, a trend observed in the UK sector of the North Sea Basin and in other ancient salt giants. However, we also document abrupt, large magnitude compositional and thickness variations adjacent to large, intra‐basin normal faults; for example, thin, carbonate‐dominated successions occur on fault‐bounded footwall highs, whereas thick, halite‐dominated successions occur only a few kilometres away in adjacent depocentres. It is presently unclear if this variability reflects variations in syn‐depositional relief related to flooding of an underfilled presalt (Early Permian) rift or syn‐depositional (Lopingian) rift‐related faulting. Irrespective of the underlying controls, variations in salt composition and thickness influenced the Middle Jurassic‐to‐Early Cretaceous rift structural style, with diapirism characterising hangingwall basins where autochthonous salt was thick and halite‐rich and salt‐detached normal faulting occurring on the basin margins and on intra‐basin structural highs where the salt was too thin and/or halite‐poor to undergo diapirism. This variability is currently not captured by existing tectono‐stratigraphic models largely based on observations from salt‐free rifts and, we argue, mapping of suprasalt structural styles may provide insights into salt composition and thickness in areas where boreholes are lacking or seismic imaging is poor.     

Magnetic anomalies associated with salt tectonism,deep structure and regional tectonics in the Maritimes Basin,Atlantic Canada

The structure and tectonic evolution of an evaporite basin are investigated in this case study, which combines the interpretation of magnetic data with the more commonly applied seismic reflection and gravity methods. The Maritimes Basin contains up to 18 km of Upper Palaeozoic sedimentary rocks resting on the basement of the Acadian orogeny. Carboniferous rocks are intensely deformed to the southeast of the Magdalen Islands as a result of deformation of evaporites of the Viséan Windsor Group. Short‐wavelength (<5 km) magnetic lineations define NNE‐ and ENE‐trending linear belts, coincident with the mapped pattern of salt structures. Magnetic models show that these lineations can be explained by the infill of subsidence troughs by high‐susceptibility sediment and/or the presence of basaltic rocks, similar to those uplifted and exposed on the Magdalen Islands. Additional shallow, magnetic sources are interpreted to result from alteration mineralization in salt‐impregnated, iron‐rich sedimentary rocks, brecciated during salt mobilization. Magnetic susceptibility measurements of samples from the Pugwash mine confirm the presence of higher susceptibility carnallite‐rich veins within salt units. Salt tectonism and basin development were influenced by the structure of the base group, the deepest regionally continuous seismic reflections (ca. 5–11 km), associated with an unconformity at the base of the Windsor Group, sampled at the Cap Rouge well. Salt structural evolution, formation of the magnetic lineations and geometry of the base group are associated with regional dextral transpression during basin development (late Carboniferous) and/or Alleghanian Orogeny (late Carboniferous to Permian). In this and similar studies, the effective use of magnetics is dependent upon the presence of rocks of high magnetic susceptibility in contrast to the low‐susceptibility salt bodies. In the absence of high‐susceptibility rocks, magnetic lows over the salt structures may be modelled, similar to commonly applied gravity techniques, to derive the internal structure and geometry.     

New insights on measured and calculated vitrinite reflectance

Measurement of dispersed vitrinite reflectance in organic sediments is one of the few regional data sets used for placing bounds on the thermal history of a sedimentary basin. Reflectance data are important when access to complementary information such as high‐quality seismic data is unavailable to place bounds on subsidence history and in locations where uplift is an important part of the basin history. Attributes which make vitrinite reflectance measurements a useful data set are the relative ease of making the measurement, and the availability of archived well cores and cuttings in state, provincial, and federal facilities. In order to fully utilize vitrinite data for estimating the temperature history in a basin, physically based methods are required to calibrate an equivalent reflectance from a modelled temperature history with measured data. The most common method for calculating a numerical vitrinite reflectance from temperature history is the EASY%R_o method which we show systematically underestimates measured data. We present a new calculated reflectance model and an adjustment to EASY%R_o which makes the correlation between measured vitrinite values and calculated vitrinite values a physical relationship and more useful for constraining thermal models. We then show that calibrating the thermal history to vitrinite on a constant age date surface (e.g., top Cretaceous) instead of calibrating the thermal history in depth removes the heating rate component from the reflectance calculation and makes thermal history calibration easier to understand and more directly related to heat flow. Finally, we use bounds on the vitrinite–temperature relationships on a constant age date surface to show that significant uncertainty exists in the vitrinite data reported in most data sets.     

Salt tectonic controls on deep‐water turbidite depositional systems: Miocene,southwestern Lower Congo Basin,offshore Angola

Regionally extensive 3D seismic data from the Lower Congo Basin, offshore Angola, have been used to investigate the influence of salt‐related structures on the location, geometry and evolution of Miocene deep‐water depositional systems. Isochron variations and cross‐sectional lap‐out relationships have then been used to qualitatively reconstruct the syn‐depositional morphology of salt‐cored structures. Coherence and Red‐green‐blue‐blended spectral decomposition volumes, tied to cross‐sectional seismic facies, allow imaging of the main sediment transport pathways and the distribution of their component seismic facies. Major sediment transport pathways developed in an area of complex salt‐related structures comprising normal faults, isolated diapirs and elongate salt walls with intervening intraslope basins. Key structural controls on the location of the main sediment transport pathways and the local interaction between lobe‐channel‐levee systems and individual structures were the length and height of structures, the location and geometry of segment boundaries, the growth and linkage of individual structures, and the incidence angle between structural strike and flow direction. Where the regional flow direction was at a high angle to structural strike, transport pathways passed progressively through multiple intraslope basins in a fill and spill manner. Segment boundaries and structural lows between diapirs acted as spill points, focusing sediment transport between intraslope basins. Channel–lobe transitions are commonly associated with these spill points, where flows expanded and entered depocentres. Deflection of channel‐levee complexes around individual structures was mainly controlled by the length of structures and incidence angle. Where regional flow direction was at a low angle to structural strike, sediment transport pathways ran parallel to structure and were confined to individual intraslope basins for many tens of kilometres. Spill between intraslope basins was rare. The relative position of structures and their segment boundaries was fixed during the Miocene, which effectively pinned the locations where sediment spilled from one intraslope basin to the next. As a result, major sediment transport pathways were used repeatedly, giving rise to vertically stacked lobe‐channel‐levee complexes along the pathways. Shadow zones devoid of coarse clastics developed in areas that were either structurally isolated from the sediment transport pathways or bypassed as a result of channel diversion.     

Controls on fluvial sedimentary architecture and sediment‐fill state in salt‐walled mini‐basins: Triassic Moenkopi Formation,Salt Anticline Region,SE Utah,USA

The Triassic Moenkopi Formation in the Salt Anticline Region, SE Utah, represents the preserved record of a low‐relief ephemeral fluvial system that accumulated in a series of actively subsiding salt‐walled mini‐basins. Development and evolution of the fluvial system and its resultant preserved architecture was controlled by the following: (1) the inherited state of the basin geometry at the time of commencement of sedimentation; (2) the rate of sediment delivery to the developing basins; (3) the orientation of fluvial pathways relative to the salt walls that bounded the basins; (4) spatially and temporally variable rates and styles of mini‐basin subsidence and associated salt‐wall uplift; and (5) temporal changes in regional climate. Detailed outcrop‐based tectono‐stratigraphic analyses demonstrate how three coevally developing mini‐basins and their intervening salt walls evolved in response to progressive sediment loading of a succession of Pennsylvanian salt (the Paradox Formation) by the younger Moenkopi Formation, deposits of which record a dryland fluvial system in which flow was primarily directed parallel to a series of elongate salt walls. In some mini‐basins, fluvial channel elements are stacked vertically within and along the central basin axes, in response to preferential salt withdrawal and resulting subsidence. In other basins, rim synclines have developed adjacent to bounding salt walls and these served as loci for accumulation of stacked fluvial channel complexes. Neighbouring mini‐basins exhibit different styles of infill at equivalent stratigraphic levels: sand‐poor basins dominated by fine‐grained, sheet‐like sandstone fluvial elements, which are representative of nonchannelised flow processes, apparently developed synchronously with neighbouring sand‐prone basins dominated by major fluvial channel‐belts, demonstrating effective partitioning of sediment route‐ways by surface topography generated by uplifting salt walls. Reworked gypsum clasts present in parts of the stratigraphy demonstrate the subaerial exposure of some salt walls, and their partial erosion and reworking into the fill of adjoining mini‐basins during accumulation of the Moenkopi Formation. Complex spatial changes in preserved stratigraphic thickness of four members in the Moenkopi Formation, both within and between mini‐basins, demonstrates a complex relationship between the location and timing of subsidence and the infill of the generated accommodation by fluvial processes.     

Rapid outer marginal collapse at the rift to drift transition of passive margin evolution,with a Gulf of Mexico case study

Interpretation of long‐offset 2D depth‐imaged seismic data suggests that outer continental margins collapse and tilt basinward rapidly as rifting yields to seafloor spreading and thermal subsidence of the margin. This collapse post‐dates rifting and stretching of the crust, but occurs roughly ten times faster than thermal subsidence of young oceanic crust, and thus is tectonic and pre‐dates the ‘drift stage’. We term this middle stage of margin development ‘outer margin collapse’, and it accords with the exhumation stage of other authors. Outer continental margins, already thinned by rifting processes, become hanging walls of crustal‐scale half grabens associated with landward‐dipping shear zones and zones of low‐shear strength magma at the base of the thinned crust. The footwalls of the shear zones comprise serpentinized sub‐continental mantle that commonly becomes exhumed from beneath the embrittled continental margin. At magma‐poor margins, outer continental margins collapse and tilt basinward to depths of about 3 km subsea at the continent–ocean transition, often deeper than the adjacent oceanic crust (accreted later between 2 and 3 km). We use the term ‘collapse’ because of the apparent rapidity of deepening (<3 Myr). Rapid salt deposition, clastic sedimentation (deltaic), or magmatism (magmatic margins) may accompany collapse, with salt thicknesses reaching 5 km and volcanic piles 1525 km. This mechanism of rapid salt deposition allows mega‐salt basins to be deposited on end‐rift unconformities at global sea level, as opposed to deep, air‐filled sub‐sea depressions. Outer marginal collapse is ‘post‐rift’ from the perspective of faulting in the continental crust, but of tectonic, not of thermal, origin. Although this appears to be a global process, the Gulf of Mexico is an excellent example because regional stratigraphic and structural relations indicate that the pre‐salt rift basin was filled to sea level by syn‐rift strata, which helps to calibrate the rate and magnitude of collapse. We examine the role of outer marginal detachments in the formation of East India, southern Brazil and the Gulf of Mexico, and how outer marginal collapse can migrate diachronously along strike, much like the onset of seafloor spreading. We suggest that backstripping estimates of lithospheric thinning (beta factor) at outer continental margins may be excessive because they probably attribute marginal collapse to thermal subsidence.     

Unravelling the multi-stage burial history of the Swiss Molasse Basin: integration of apatite fission track, vitrinite reflectance and biomarker isomerisation analysis

A complex basin evolution was studied using various methods, including thermal constraints based on apatite fission‐track (AFT) analysis, vitrinite reflectance (VR) and biomarker isomerisation, in addition to a detailed analysis of the regional stratigraphic record and of the lithological properties. The study indicates that (1) given the substantial amount of data, the distinction and characterisation of successive stages of heating and burial in the same area are feasible, and (2) the three thermal indicators (AFT, VR and biomarkers) yield internally consistent thermal histories, which supports the validity of the underlying kinetic algorithms and their applicability to natural basins. All data pertaining to burial and thermal evolution were integrated in a basin model, which provides constraints on the thickness of eroded sections and on heat flow over geologic time. Three stages of basin evolution occurred in northern Switzerland. The Permo‐Carboniferous strike–slip basin was characterised by high geothermal gradients (80–100°C km^?1) and maximum temperature up to 160°C. After the erosion of a few hundreds of metres in the Permian, the post‐orogenic, epicontinental Mesozoic basin developed in Central Europe, with subsidence triggered by several stages of rifting. Geothermal gradients in northern Switzerland during Cretaceous burial were relatively high (35–40°C km^?1), and maximum temperature typically reached 75°C (top middle Jurassic) to 100°C (base Mesozoic). At least in the early Cretaceous, a stage of increased heat flow is needed to explain the observed maturity level. After erosion of 600–700 m of Cretaceous and late Jurassic strata during the Paleocene, the wedge‐shaped Molasse Foreland Basin developed. Geothermal gradients were low at this time (≤20°C km^?1). Maximum temperature of Miocene burial exceeded that of Cretaceous burial in proximal parts (<35 km from the Alpine front), but was lower in more distal parts (>45 km). Thus, maximum temperature as well as maximum burial depth ever reached in Mesozoic strata occurred at different times in different regions. Since the Miocene, 750–1050 m were eroded, a process that still continues in the proximal parts of the basin. Current average geothermal gradients in the uppermost 2500 m are elevated (32–47°C km^?1). They are due to a Quaternary increase of heat flow, most probably triggered by limited advective heat transport along Paleozoic faults in the crystalline basement.     

黑河流域张掖市近38 a以来气候变化特征分析

 目前黑河流域气候变化研究多集中于流域系统气候变化与区域水资源变化之间的关系、区域沙漠化、沙尘暴发生的气候动因等研究方面，而对人类活动强度大、活动最为密集的流域绿洲区域张掖市气候变化所作研究较少。通过对张掖市六县（区）6个气象观测站近38 a以来的逐月平均气温、降水、大风频率资料的系统分析，认为张掖市近38 a来气温升高幅度较之全国其他区域更为明显。多年降水变化相对不大，但冬春两季降水出现缓慢增加的趋势，大风天气与沙尘暴发生频数近38 a来出现了明显的下降趋势，这与区域气温升高及冬春两季易发生沙尘暴的期间降水增加有明显的相关性。同时人类对干旱区内陆河流域绿洲开发的加深也一定程度上对这种生态环境敏感地区的气候产生影响。     

Influence of the mechanical behaviour of brittle–ductile fold–thrust belts on the development of foreland basins

A two‐dimensional mathematical model considering coupling between a deforming elasto‐visco‐plastic fold–thrust belt, flexural subsidence and diffusional surface processes is solved using the Finite Element Method to investigate how the mechanical behaviour of brittle–ductile wedges influences the development of foreland basins. Results show that, depending mainly on the strength of the basal décollement, two end‐member types of foreland basin are possible. When the basal detachment is relatively strong, the foreland basin system is characterised by: (1) Highly asymmetrical orogen formed by thrusts concentrated in the incoming pro‐wedge. (2) Sedimentation on retro‐side takes place in one major foredeep basin which grows throughout orogen evolution. (3) Deposition on the pro‐side occurs initially in the foredeep, and continues in the wedge‐top before isolated basins are advected towards the orogen core where they become uplifted and exhumed. (4) Most pro‐wedge basins show an upward progression from low altitude, foredeep deposits at the base to high altitude, wedge‐top deposits near the surface. In contrast, when the basal detachment behaves weakly due to the presence of low viscosity material such as salt, the foreland basin system is characterised by (1) Broad, low relief orogen showing little preferential vergence and predominance of folding relative to faulting. (2) Deposition mainly in wedge‐top basins showing growth strata. (3) Many basins are initiated contemporaneously but form discontinuously due to the locus of active deformation jumping back and forth between different structures. Model results successfully reproduce first order observations of deforming brittle–ductile wedges and foreland basins. Moreover, the results support and provide a framework for understanding the existence of two main end‐member foreland basin types, simple and complex, associated with fold–thrust belts whose detachments are relatively strong and weak, respectively.     

Influence of minibasin obstruction on canopy dynamics in the northern Gulf of Mexico

In salt‐detached gravity‐gliding/spreading systems the detachment geometry is a key control on the downslope mobility of the supra‐salt sequence. Here, we used regional 3D seismic data to examine a salt‐stock canopy in the northern Gulf of Mexico slope, in an area where supra‐canopy minibasins subsided vertically and translated downslope above a complex base‐of‐salt. If thick enough, minibasins can interact with, and weld to, the base‐of‐salt and be obstructed from translating downslope. Based on the regional maps of the base of allochthonous salt and the base of the supra‐canopy sequence, the key controls on minibasin obstruction, we distinguished two structural domains in the study area: a highly obstructed domain and a highly mobile domain. Large‐scale translation of the supra‐canopy sequence is recorded in the mobile domain by a far‐travelled minibasin and a ramp syncline basin. These two structures suggest downslope translation on the order of 40 km from Plio‐Pleistocene to Present. In contrast, translation was impeded in the obstructed domain due to supra‐canopy bucket minibasins subsiding into feeders during the Pleistocene. As a result, we infer that differential translation occurred between the two domains and argue that a deformation area between two differentially translating supra‐canopy minibasin domains is difficult to recognize. However, characterizing domains according to base‐of‐salt geometry and supra‐canopy minibasin configuration can be helpful in identifying domains that may share similar subsidence and downslope translation histories.     

Numerical modelling study of mechanisms of mid‐basin salt canopy evolution and their potential applications to the Northwestern Gulf of Mexico

Salt canopies are present in many of the worldwide large salt basins and are key players in the basins' structural evolution as well as in the development of associated hydrocarbon systems. This study employs 2D finite‐element models which incorporate the dynamical interaction of viscous salt and frictional‐plastic sediments in a gravity‐spreading system. We investigate the general emplacement of salt canopies that form in the centre of a large, autochthonous salt basin. This is motivated by the potential application to a mid‐basin canopy in the NW Gulf of Mexico (GoM) that developed in the late Eocene. Three different salt expulsion and canopy formation concepts that have been proposed in the salt‐tectonic literature for the GoM are tested. Two of these mechanisms require pre‐existing diapirs as precursory structures. We include their evolution in the models to assure a continuous, smooth evolution of the salt‐sediment system. The most efficient canopy formation takes place under the squeezed diapir mechanism. Here, shortening of a region containing pre‐existing diapirs is absorbed by the salt (the weakest part of the system), which is then expelled onto the seafloor. The expulsion rollover mechanism, which evacuates salt from beneath evolving rollover structures and expels it both laterally and to the surface, was not successfully captured by the numerical models. No rollover structures developed and only minor amounts of allochthonous salt emerged to the seafloor. The breached anticline mechanism requires substantial shortening of salt‐cored, pre‐weakened folds such that the salt breaches the anticlines and is expelled to the seafloor. The amount of shortening may be too large to occur in the central part of a salt basin, but may explain canopy evolution closer to the distal end of the allochthonous salt. When applying the different concepts to the northwestern GoM, none of the models adequately describes the entire system, yet the squeezed diapir mechanism captures most structural features of the Eocene paleocanopy. It is nevertheless possible that different mechanisms have acted in combination or sequentially in the northwestern GoM.     

The long-term thermal consequences of rifting: implications for basin reactivation

The attenuation of the continental crust during rifting and the subsequent filling of the rift‐related accommodation alter the long‐term thermal and mechanical state of the lithosphere. This is primarily because the Moho is shallowed due to density contrasts between the sediment fill and the crust, but also reflects the attenuation of the pre‐existing crustal heat production and its burial beneath the basin, as well the thermal properties of the basin fill. Moho shallowing and attenuation of pre‐existing heat production contribute to long‐term cooling of the Moho and thus lithospheric strengthening, as has been pointed out in many previous studies. In contrast, basin filling normally contributes to significant Moho heating allowing the possibility of long‐term lithospheric weakening, the magnitude of which is dependent on the thermal properties of the basin‐fill and the distribution of heat sources in the crust. This paper focuses on the thermal property structure of the crust and basin‐fill in effecting long‐term changes in lithospheric thermal regime, with particular emphasis on the distribution of heat producing elements in the crust. The parameter space appropriate to typical continental crust is explored using a formalism for the heat production distributions that makes no priori assumptions about the specific form of the distribution. The plausible parameter space allows a wide range in potential long‐term thermal responses. However, with the proviso that the accommodation created by the isostatic response to rifting is essentially filled, the long‐term thermal response to rift basin formation will generally increase average crustal thermal gradients beneath basins but cool the Moho due to its reduction in depth. The increase in the average crustal thermal gradient induces lateral heat flow that necessarily heats the Moho along basin margins, especially in narrow rift basins. Using coupled thermo‐mechanical models with temperature sensitive creep‐parameters, we show that such heating may be sufficient to localise subsequent deformation in the vicinity of major basin bounding structures, potentially explaining the offset observed in some stacked rift basin successions.     

Water use in the transboundary basin of the Amur river

This paper summarizes the problems and consequences associated with water use in the Russian and Chinese parts of the Amur river basin. Taking into consideration the set of indicators involving the water withdrawal, the utilization of source water, the volumes of recirculated and repeated-consecutive water supply, the volumes of waste waters, the capacity of pollution control facilities, etc., an outline is given of the present status of water use in the national parts of the basin. The future amounts of water consumption are forecasted, and it is shown how it will increase in the Russian as well as the Chinese parts. An analysis of the spatiotemporal dynamics of water-use indicators revealed the differently directed tendencies in the water-use pattern in the Russian and Chinese parts of the Amur river basin, and the existence of quantitative disproportions caused by a different degree of development and a different intensity of economic growth. In the Russian part of the basin, the amounts of water used have stabilized in recent years after a decrease, whereas they are increasing steadily in the Chinese and Russian parts where the highest proportion of water is used to meet agricultural and production needs, respectively. It is shown that water use, the density of the water-economy structure and the discharges of pollutants in the Chinese part of the basin are larger by factors of several tens than those in the Russian part. The manufacture of water-intensive industrial products and the load of agriculture on water resources also differ by factors of several tens. The indicator of population size is used to characterize the degree of development of the basin’s territory. For the Russian part of the basin the study revealed a dependence of water consumption on the population size and on the volumes of water-intensive products in the production facilities with a low coefficient of recirculated water use. This dependence can also be extended to the Chinese part where circulated water supplies are being used only moderately.     

艾比湖流域水土开发的模糊综合评价

近年来随着水土开发活动的加剧,艾比湖流域已经成为我国干旱区生态环境严重退化的地区之一。水土资源利用的有效程度是区域水土资源可持续发展的前提与基础．直接关系水土资源的可持续利用。本文运用模糊综合评价模型．对艾比湖流域水土开发的有效性进行了评价。结果显示：艾比湖流域水资源开发利用率较高．平均达到75．99％;但水土资源有效利用率偏低．有效开发利用程度综合评分值只有0．316;水土资源开发处于低级及过渡阶段,工农业及经济属于耗水型．水资源综合管理水平低,但同时也说明水资源开发具有很大潜力。以评价结论为依据,给出了流域可持续发展水土资源保障的对策建议。