Lateral fold growth and linkage in the Zagros fold and thrust belt (Kurdistan,NE Iraq)

The Zagros fold and thrust belt is a seismically active orogen that has accommodated the N–S shortening between the Arabian and Eurasian plates since the Miocene. Whereas the southeast parts of the belt have been studied in detail, the northwest extent has received considerably less attention, being part of the Republic of Iraq. In this study, we investigate fold growth in the area NE of Erbil (Kurdistan, Iraq). In particular, we focus on the interaction of the transient development of drainage patterns along growing antiforms, as this directly reflects the kinematics of progressive fold growth. Detailed geomorphological studies of the Bana Bawi‐, Permam‐ and Safeen‐fold trains show that these anticlines did not develop from a single embryonic fold but by lateral linkage of several different fold segments. These segments, with length between 5 and 25 km, have been detected by mapping ancient and modern river courses; these initially cut the nose of growing folds until eventually defeated, leaving curved wind gaps behind. Depending on the alignment of the initial embryonic folds, the segments can either record a linear‐ or an en‐echelon linkage. Comparison of natural examples from the Zagros fold and thrust belt in Iraq with published numerically modelled fold growth suggests that both linear‐linkage and en‐echelon linkage are mechanically feasible and are common processes during progressive shortening and fold growth.     

Syn‐depositional thin‐ and thick‐skinned extensional tectonics in the mid‐Cretaceous Lasarte sub‐basin,western Pyrenees

In the mid‐Cretaceous Lasarte sub‐basin (LSB) [northeastern Basque‐Cantabrian Basin (BCB)] contemporaneous and syn‐depositional thin‐ and thick‐skinned extensional tectonics occur due to the presence of a ductile detachment layer that decoupled the extension. Despite the interest in extension modes of rift basins bearing intra‐stratal detachment layers, complex cases remain poorly understood. In the LSB, field results based on mapping, stratigraphic, sedimentological and structural data show the relationship between growth strata and tectonic structures. Syn‐depositional extensional listric faults and associated folds and faults have been identified in the supra‐detachment thin‐skinned system. But stratigraphic data also indicate the activation of sub‐detachment thick‐skinned extensional faults coeval with the development of the thin‐skinned system. The tectono‐sedimentary evolution of the LSB, since the Late Aptian until the earliest Late Albian, has been interpreted based on thin‐ and thick‐skinned extensional growth structures, which are fossilized by post‐extensional strata. The development of the thin‐skinned system is attributed to the presence of a ductile detachment layer (Upper Triassic Keuper facies) which decoupled the extension from deeper sub‐detachment basement‐involved faulting under a regional extensional/transtensional regime.     

Unroofing the core of the central Andean fold‐thrust belt during focused late Miocene exhumation: evidence from the Tipuani‐Mapiri wedge‐top basin,Bolivia

As the highest part of the central Andean fold‐thrust belt, the Eastern Cordillera defines an orographic barrier dividing the Altiplano hinterland from the South American foreland. Although the Eastern Cordillera influences the climatic and geomorphic evolution of the central Andes, the interplay among tectonics, climate and erosion remains unclear. We investigate these relationships through analyses of the depositional systems, sediment provenance and ⁴⁰Ar/³⁹Ar geochronology of the upper Miocene Cangalli Formation exposed in the Tipuani‐Mapiri basin (15–16°S) along the boundary of the Eastern Cordillera and Interandean Zone in Bolivia. Results indicate that coarse‐grained nonmarine sediments accumulated in a wedge‐top basin upon a palaeotopographic surface deeply incised into deformed Palaeozoic rocks. Seven lithofacies and three lithofacies associations reflect deposition by high‐energy braided river systems, with stratigraphic relationships revealing significant (～500 m) palaeorelief. Palaeocurrents and compositional provenance data link sediment accumulation to pronounced late Miocene erosion of the deepest levels of the Eastern Cordillera. ⁴⁰Ar/³⁹Ar ages of interbedded tuffs suggest that sedimentation along the Eastern Cordillera–Interandean Zone boundary was ongoing by 9.2 Ma and continued until at least ～7.4 Ma. Limited deformation of subhorizontal basin fill, in comparison with folded and faulted rocks of the unconformably underlying Palaeozoic section, implies that the thrust front had advanced into the Subandean Zone by the 11–9 Ma onset of basin filling. Documented rapid exhumation of the Eastern Cordillera from ～11 Ma onward was decoupled from upper‐crustal shortening and coeval with sedimentation in the Tipuani‐Mapiri basin, suggesting climate change (enhanced precipitation) or lower crustal and mantle processes (stacking of basement thrust sheets or removal of mantle lithosphere) as possible controls on late Cenozoic erosion and wedge‐top accumulation. Regardless of the precise trigger, we propose that an abruptly increased supply of wedge‐top sediment produced an additional sedimentary load that helped promote late Miocene advance of the central Andean thrust front in the Subandean Zone.     

Closing and continentalization of the South Pyrenean foreland basin (NE Spain): magnetochronological constraints

This paper presents new magnetostratigraphic results from a 1100‐m‐thick composite section across the marine to continental sediments of the central part of the SE margin of the Ebro basin (NE Spain). Integration with existing marine and continental biochronological data allows a robust correlation with the geomagnetic polarity time scale. The resulting absolute chronology ranges from 36.3 to 31.1 Ma (Priabonian to Rupelian), and yields an interpolated age of ～36.0 Ma (within chron C16n.2n) for the youngest marine sediments of the eastern Ebro basin. This age is in concordance with a reinterpretation of earlier magnetostratigraphic data from the western South Pyrenean foreland basin, and indicates that continentalization of the basin occurred as a rapid and isochronous event. The basin continentalization, determined by the seaway closure that resulted from the uplift of the western Pyrenees, was probably coincident with a mid‐amplitude eustatic sea level low with a maximum at 36.2 Ma. The base level drop that followed the basin closure and desiccation does not appear associated to a significant sedimentary hiatus along the margins, suggesting a late Eocene shallow marine basin that rapidly refilled and raised its base level after the seaway closing. Rapid basin filling following continentalization predates the phase of rapid exhumation of the Central Pyrenean Axial Zone from 35.0 to 32.0 Ma, determined from the thermochronology data. It is possible then that sediment aggradation at the front of the fold‐and‐thrust belt could have contributed to a decrease in the taper angle, triggering growth of the inner orogenic wedge through break‐back thrusting and underplating. Contrasting sedimentation trends between the western and eastern sectors of the South Pyrenean foreland indicate that basin closing preferentially affected those areas subjected to sediment bypass towards the ocean domain. As a result, sediment ponding after basin closure is responsible for a two‐fold increase of sedimentation rates in the western sector, while changes of sedimentation rates are undetected in the more restricted scenario of the eastern Ebro basin.     

Mass‐transport complexes as markers of deep‐water fold‐and‐thrust belt evolution: insights from the southern Magdalena fan,offshore Colombia

Mass wasting is an important process in the degradation of deep‐water fold‐and‐thrust belts. However, the relationship between mass‐transport complex (MTC) emplacement and the timing and spatial progression of contractional deformation of the seabed have not been extensively studied. This study uses high‐quality, 3D seismic reflection data from the southern Magdalena Fan, offshore Colombia to investigate how the growth of a deep‐water fold‐and‐thrust belt (the southern Sinú fold belt) is recorded in the source, distribution and size of MTCs. More than nine distinct, but coalesced MTCs overlie a major composite basal erosion surface. This surface formed by multiple syn‐ and post‐tectonic mass‐wasting events and is thus highly diachronous, thereby recording a protracted period of tectonism, seascape degradation and associated sedimentation. The size and source location of these MTCs changed through time: the oldest ‘detached’ MTCs are relatively small (over 9–100 km² in area) and sourced from the flanks of growing anticlines, whereas the younger ‘shelf‐attached’ MTCs are considerably larger (more than 200–300 km²), are sourced from the shelf, and post‐date the main phase of active folding and thrusting. Changes in the source, distribution and size of MTCs are tied to the sequential nucleation, amplification and along‐strike propagation of individual structures, showing that MTCs can be used to constrain the timing and style of contractional deformation, and seascape evolution in time and space.     

Ebro Basin continental sedimentation associated with late compressional Pyrenean tectonics(north‐eastern Iberia): controls on basin margin fans and fluvial systems

ABSTRACT This contribution deals with the External Sierras and a part of the foreland Ebro Basin related to the southern Pyrenean thrust front. The structure of the External Sierras consists of a south‐verging thrust system developed from middle Eocene to early Miocene times. Since the end of the early Oligocene, a regional‐scale detachment anticline (the Santo Domingo anticline) developed, folding the original thrust system and creating new thrust units. The molassic fill in this part of the Ebro Basin (Uncastillo Formation) mainly corresponds to an extensive, composite distributary fluvial system, termed the Luna system, which drained the uplifted Gavarnie Unit to the north. Small, marginal alluvial fans originated along the External Sierras and coalesced in the proximal‐middle portions of the Luna system. Three tecto‐sedimentary units (TSU), late Oligocene to early Miocene in age, comprise the Uncastillo Formation. Lateral relationships and areal distribution of lithofacies through time have been used to establish sedimentary models for the marginal alluvial fans and the Luna fluvial system. Their sedimentary evolution was controlled by tectonics affecting the drainage basins, and based on mapping and stratigraphic relationships of the TSU, the temporal succession of the marginal alluvial fans and their relationships with each thrust system in the south Pyrenean front can be shown. Alluvial fan formation evolved through time from west to east, in accord with the progressive eastward growth of the Santo Domingo anticline as a conical fold. The fluvial network of the Luna system appears to have been mainly radial, but near the basin margin its architecture was influenced by the syndepositional Fuencalderas and Uncastillo anticlines developed within the Ebro Basin. These low‐amplitude folds originated by layer‐parallel shearing caused by rotation of the southern flank of the Santo Domingo anticline. Progressive uplift of these anticlines constrained part of the fluvial discharge to synclinal areas parallel to the basin margin; these areas where characterized by meandering sandy channels. At the peripheral tips of the anticlines the channel system flowed basinward.     

Crustal‐scale fluid flow during the tectonic evolution of the Bighorn Basin (Wyoming,USA)

Stable isotope measurements (O, C, Sr), microthermometry and salinity measurements of fluid inclusions from different fracture populations in several anticlines of the Sevier‐Laramide Bighorn basin (Wyoming, USA) were used to unravel the palaeohydrological evolution. New data on the microstructural setting were used to complement previous studies and refine the fracture sequence at basin scale. The latter provides the framework and timing of fluid migration events across the basin during the Sevier and Laramide orogenic phases. Since the Sevier tectonic loading of the foreland basin until its later involvement into the Laramide thick‐skinned orogeny, three main fracture sets (out of seven) were found to have efficiently enhanced the hydraulic permeability of the sedimentary cover rocks. These pulses of fluid are attested by calcite crystals precipitated in veins from hydrothermal (T > 120 °C) radiogenic fluids derived from Cretaceous meteoric fluids that interacted with the Precambrian basement rocks. Between these events, vein calcite precipitated from formational fluids at chemical and thermal equilibrium with surrounding environment. At basin scale, the earliest hydrothermal pulse is documented in the western part of the basin during forebulge flexuring and the second one is documented in basement‐cored folds during folding. In addition to this East/West diachronic opening of the cover rocks to hydrothermal pulses probably controlled by the tectonic style, a decrease in ^87/86Sr values from West to East suggests a crustal‐scale partially squeegee‐type eastward fluid migration in both basement and cover rocks since the early phase of the Sevier contraction. The interpretation of palaeofluid system at basin scale also implies that joints developed under an extensional stress regime are better vertical drains than joints developed under strike‐slip regime and enabled migration of basement‐derived hydrothermal fluids.     

10 Myr evolution of sedimentation rates in a deep marine to non‐marine foreland basin system: Tectonic and sedimentary controls (Eocene,Tremp–Jaca Basin,Southern Pyrenees,NE Spain)

The propagation of the deformation front in foreland systems is typically accompanied by the incorporation of parts of the basin into wedge‐top piggy‐back basins, this process is likely producing considerable changes to sedimentation rates (SR). Here we investigate the spatial‐temporal evolution of SR for the Tremp–Jaca Basin in the Southern Pyrenees during its evolution from a wedge‐top, foreredeep, forebulge configuration to a wedge‐top stage. SR were controlled by a series of tectonic structures that influenced subsidence distribution and modified the sediment dispersal patterns. We compare the decompacted SR calculated from 12 magnetostratigraphic sections located throughout the Tremp–Jaca Basin represent the full range of depositional environment and times. While the derived long‐term SR range between 9.0 and 84.5 cm/kyr, compiled data at the scale of magnetozones (0.1–2.5 Myr) yield SR that range from 3.0 to 170 cm/kyr. From this analysis, three main types of depocenter are recognized: a regional depocenter in the foredeep depozone; depocenters related to both regional subsidence and salt tectonics in the wedge‐top depozone; and a depocenter related to clastic shelf building showing transgressive and regressive trends with graded and non‐graded episodes. From the evolution of SR we distinguish two stages. The Lutetian Stage (from 49.1–41.2 Ma) portrays a compartmentalized basin characterized by variable SR in dominantly underfilled accommodation areas. The markedly different advance of the deformation front between the Central and Western Pyrenees resulted in a complex distribution of the foreland depozones during this stage. The Bartonian–Priabonian Stage (41.2–36.9 Ma) represents the integration of the whole basin into the wedge‐top, showing a generalized reduction of SR in a mostly overfilled relatively uniform basin. The stacking of basement units in the hinterland during the whole period produced unusually high SR in the wedge‐top depozone.     

Along‐strike structural linkage and interaction in an active thrust fault system: A case study from the western Sichuan foreland basin,China

Along‐strike structural linkage and interaction between faults is common in various compressional settings worldwide. Understanding the kinematic history of fault interaction processes can provide important constraints on the geometry and evolution of the lateral growth of segmented faults in the fold‐and‐thrust belts, which are important to seismic hazard assessment and hydrocarbon trap development. In this study, we study lateral structural geometry (fault displacement and horizon shortening) of thrust fault linkages and interactions along the Qiongxi anticline in the western Sichuan foreland basin, China, using a high‐resolution 3D seismic reflection dataset. Seismic interpretation suggests that the Qiongxi anticline can be related to three west‐dipping, hard‐linked thrust fault segments that sole onto a regional shallow detachment. Results reveal that the lateral linkage of fault segments limited their development, affecting the along‐strike fault displacement distributions. A deficit between shortening and displacement is observed to increase in linkage zones where complex structural processes occur, such as fault surface bifurcation and secondary faulting, demonstrating the effect of fault linkage process on structural deformation within a thrust array. The distribution of the geometrical characteristics shows that thrust fault development in the area can be described by both the isolated fault model and the coherent fault model. Our measurements show that new fault surfaces bifurcate from the main thrust ramp, which influences both strain distribution in the relay zone and along‐strike fault slip distribution. This work fully describes the geometric and kinematic characteristics of lateral thrust fault linkage, and may provide insights into seismic interpretation strategies in other complex fault transfer zones.     

Basin evolution of Upper Cretaceous–Lower Cenozoic strata in the Malargüe fold‐and‐thrust belt: northern Neuquén Basin,Argentina

The Andean Orogen is the type‐example of an active Cordilleran style margin with a long‐lived retroarc fold‐and‐thrust belt and foreland basin. Timing of initial shortening and foreland basin development in Argentina is diachronous along‐strike, with ages varying by 20–30 Myr. The Neuquén Basin (32°S to 40°S) contains a thick sedimentary sequence ranging in age from late Triassic to Cenozoic, which preserves a record of rift, back arc and foreland basin environments. As much of the primary evidence for initial uplift has been overprinted or covered by younger shortening and volcanic activity, basin strata provide the most complete record of early mountain building. Detailed sedimentology and new maximum depositional ages obtained from detrital zircon U–Pb analyses from the Malargüe fold‐and‐thrust belt (35°S) record a facies change between the marine evaporites of the Huitrín Formation (ca. 122 Ma) and the fluvial sandstones and conglomerates of the Diamante Formation (ca. 95 Ma). A 25–30 Myr unconformity between the Huitrín and Diamante formations represents the transition from post‐rift thermal subsidence to forebulge erosion during initial flexural loading related to crustal shortening and uplift along the magmatic arc to the west by at least 97 ± 2 Ma. This change in basin style is not marked by any significant difference in provenance and detrital zircon signature. A distinct change in detrital zircons, sandstone composition and palaeocurrent direction from west‐directed to east‐directed occurs instead in the middle Diamante Formation and may reflect the Late Cretaceous transition from forebulge derived sediment in the distal foredeep to proximal foredeep material derived from the thrust belt to the west. This change in palaeoflow represents the migration of the forebulge, and therefore, of the foreland basin system between 80 and 90 Ma in the Malargüe area.     

Subsurface fluid flow in the deep‐water Kwanza Basin,offshore Angola

Integrated analysis of high‐quality three‐dimensional (3D) seismic, seabed geochemistry, and satellite‐based surface slick data from the deep‐water Kwanza Basin documents the widespread occurrence of past and present fluid flow associated with dewatering processes and hydrocarbon migration. Seismic scale fluid flow phenomena are defined by seep‐related seafloor features including pockmarks, mud or asphalt volcanoes, gas hydrate pingoes, as well as shallow subsurface features such as palaeo‐pockmarks, direct hydrocarbon indicators (DHIs), pipes and bottom‐simulating reflections (BSRs). BSR‐derived shallow geothermal gradients show elevated temperatures attributed to fluid advection along inclined stratigraphic carrier beds around salt structures in addition to elevated shallow thermal anomalies above highly conductive salt bodies. Seabed evidences of migrated thermogenic hydrocarbons and surface slicks are used to differentiate thermogenic hydrocarbon migration from fluid flow processes such as dewatering and biogenic gas migration. The analysis constrains the fluid plumbing system defined by the three‐dimensional distribution of stratigraphic carriers and seal bypass systems through time. Detailed integration and iterative interpretation have confirmed the presence of mature source rock and effective migration pathways with significant implications for petroleum prospectivity in the post‐salt interval. Integration of seismic, seabed geochemistry and satellite data represents a robust method to document and interpret fluid flow phenomena along continental margins, and highlights the importance of integrated fluid flow studies with regard to petroleum exploration, submarine geohazards, marine ecosystems and climate change.     

LA‐ICP‐MS dating of detrital zircon grains from the Cretaceous allochthonous bauxites of Languedoc (south of France): Provenance and geodynamic consequences

The Cretaceous of southern France is characterised by a long erosional hiatus, outlined with bauxite deposits, which represent the only remaining sedimentary record of a key period for geodynamic reconstructions. Detrital zircons from allochthonous karst bauxites of Languedoc (Southern France) have been dated using LA‐ICP‐MS (Laser Ablation Inductively Coupled Plasma Mass Spectrometry), in order to specify the age of deposition and to constrain the provenance of the weathered material. We analysed 671 single detrital zircons grains from three karst bauxitic basins, stretching from close to the Variscan Montagne Noire to the present‐day Mediterranean Sea. Analytical results provide Variscan (300–350 Ma) and Late Proterozoic (550–700 Ma) ages as primary groups. In addition, Middle‐, Late Proterozoic and Early Archean (oldest grain at 3.55 Ga) represent significant groups. Mid‐Cretaceous zircons (118–113 Ma) provide a pooled age of 115.5 ± 3.8 Ma, which constitutes the maximum age for bauxite deposition. Results also suggest a dual source for the Languedoc bauxite: one generalised sedimentary source of regional extent and a localised source in the Variscan basement structural high, that has been progressively unroofed during Albian. Integration of these new findings with previously published thermochronological data support the presence of an Early Cretaceous marly cover on the Variscan basement, which has been weathered and then, removed during the Albian. The Languedoc bauxite provide a spatial and temporal link between the uplift of southern French Massif Central to the north, and the Pyrenean rift and its eastward extension to the south. These new results allow to constrain the timing and distribution of uplift/subsidence during the mid‐Cretaceous events in relation with the motion of the Iberian plate relative to Eurasia.     

Normal faulting, extension and uplift in the outer thrust belt of the central Apennines (Italy): role of the Caramanico fault

The outer Adriatic zones of the central Apennines (Italy) provide good conditions for analysing geometry and kinematics of the earliest normal faults, superposed onto the thrust belt. During the latest stages of thrusting onto the Adriatic foreland (late Pliocene–early Pleistocene), the outermost imbricates of the thrust belt were subjected to normal faulting, coeval with differential uplift. Crosscutting normal faults get younger towards the foreland, thus the easternmost normal faults record the latest stages of fault propagation and growth. The Caramanico fault, on the western flank of Mt. Maiella, is the largest outcropping normal fault of the outer zones. This high‐angle fault (dip > 70°) has cumulative offsets ≤ €4.2 km, and propagated with slip rates of 2.6 mm/year in a short time interval (≤ 1.6 Ma), concomitant with intense uplift of Mt. Maiella. In contrast with normal faults in a more internal position, the Caramanico fault maintains a high‐angle planar geometry, and does not reach the major basal detachment of the thrust belt. Thus the fault did not cause large extensional displacements; its major role was rather to accommodate ongoing components of vertical uplift of the overthickened thrust wedge. Downfaulting of the thrust belt on the western flank of Mt. Maiella represents the youngest end member of the same processes that have operated since 11 Ma in the Tyrrhenian hinterland, where large extensional strains and crustal thinning of the orogenic belt were achieved by long‐lasting activity of listric normal faults detached at lower crustal depths.     

Analysis of the Devonian (Frasnian) platform from Belgium: a multi‐faceted approach for basin evolution reconstruction

This study undertakes a multi‐disciplinary approach (sedimentology, carbon isotopes, magnetic susceptibility and thickness distribution) to improve understanding of a major Palaeozoic carbonate platform, the Frasnian platform of Belgium. These combined techniques are used to reconstruct the platform history, which evolved in two main steps. During the first phase, the basin was strongly influenced by faulting, producing notable thickness and facies variations, with open ocean conditions, with good water circulation and no/or limited barrier reef. The second phase of platform development was less influenced by differential subsidence, as indicated by homogeneous facies distribution. However, this platform developed under restricted waters, with low circulation which is likely related to the development of a barrier reef.     

Tectono‐climatic evolution of a Neogene intramontane basin (Late Miocene Carboneras subbasin,southeast Spain): revelations from basin mapping and biofacies analysis

Exceptional 3‐D exposures of fault blocks forming a 5 km × 10 km clastic sediment‐starved, marine basin (Carboneras subbasin, southeast Spain) allow a test of the response of carbonate sequence stratigraphic architectures to climatic and tectonic forcing. Temperate and tropical climatic periods recorded in biofacies serve as a chronostratigraphic framework to reconstruct the status of the basin within three time‐slices (late Tortonian–early Messinian, late Messinian, Pliocene). Structural maps and isopach maps trace out the distribution of fault blocks, faults, and over time, their relative motions, propagational patterns and life times, which demonstrate a changing layout of the basin because of a rotation of the regional transtensional stress field. Progradation of early Messinian reefal systems was perpendicular to the master faults of the blocks, which were draped by condensed fore‐slope sediments. The hangingwall basins coincided with the toe‐of‐slope of the reef systems. The main phase of block faulting during the late Tortonian and earliest Messinian influenced the palaeogeography until the late Pliocene (cumulative throw < 150–240 m), whereas displacements along block bounding faults, which moved into the hangingwall, died out over time. An associated shift of the depocentres of calciturbidites, slump masses and fault scarp degradation breccias reflects 500–700 m of fault propagation into the hangingwall. The shallow‐water systems of the footwall areas were repeatedly subject to emergence and deep peripheral erosion, which imply slow net relative uplift of the footwall. In the dip‐slope settings, erosional truncations of tilted proximal deposits prevail, which indicate rotational relative uplift. Block movements were on the order of magnitude of third order sea‐level fluctuations during the late Tortonian and earliest Messinian. We suggest that this might be the reason for the common presence of offlapping geometries in early Messinian reef systems of the Betic Cordilleras. During the late Pliocene, uplift rates fell below third order rates of sea‐level variations. However, at this stage, the basin was uplifted too far to be inundated by the sea again. The evolution of the basin may serve as a model for many other extensional basins around the world.     

Growth fold controls on carbonate distribution in mixed foreland basins: insights from the Amiran foreland basin (NW Zagros,Iran) and stratigraphic numerical modelling

The evolution from Late Cretaceous to early Eocene of the well dated Amiran foreland basin in the NW Iranian Zagros Mountains is studied based on the reconstruction of successive thickness, palaeobathymetry and subsidence maps. These maps show the progressive forelandwards migration of the mixed carbonate‐siliciclastic system associated with a decrease in creation of accommodation. Carbonate facies variations across the basin suggest a structural control on the carbonate distribution in the Amiran foreland basin, which has been used as initial constraint to study the control exerted by syndepositional folding in basin architecture and evolution by means of stratigraphic numerical modelling. Modelled results show that shallow bathymetries on top of growing folds enhance carbonate production and basin compartmentalization. As a consequence, coarse clastics become restricted to the internal parts of the basin and only the fine sediments can by‐pass the bathymetric highs generated by folding. Additionally, the development of extensive carbonate platforms on top of the anticlines favours the basinwards migration of the depositional system, which progrades farther with higher fold uplift rates. In this scenario, build‐ups on top of anticlines record its growth and can be used as a dating method. Extrapolation of presented modelling results into the Amiran foreland basin is in agreement with an early folding stage in the SE Lurestan area, between the Khorramabad and Kabir Kuh anticlines. This folding stage would enhance the development of carbonate platforms on top of the anticlines, the south‐westward migration of the system and eventually, the complete filling of the basin north of the Chenareh anticline at the end of the Cuisian. Incremental thickness maps are consistent with a thin (0.4–2 km) ophiolite complex in the source area of the Amiran basin.     

Along‐strike evolution of folding,stretching and breaching of supra‐salt strata in the Plataforma Burgalesa extensional forced fold system (northern Spain)

The Plataforma Burgalesa is a partly exposed extensional forced fold system with an intermediate salt layer, which has developed along the southern portion of the Basque‐Cantabrian Basin from Malm to Early Cretaceous as part of the Bay of Biscay‐Pyrenean rift system. Relationships between syn‐ and pre‐rift strata of the supra‐salt cover sequence and distribution of intra‐cover second‐order faults are observed both along seismic sections and at the surface. These relationships indicate an along‐strike variability of the extensional structural style. After a short period of salt mobilization and forced folding, high slip rates in the central portion of the major basement faults have rapidly promoted brittle behaviour of the salt layer, preventing further salt mobilization and facilitating the propagation of the fault across the salt layer. In contrast, at the tip regions of basement faults, slower slip rates have facilitated ductile salt behaviour, ensuring its further evaporite evacuation, preventing fault propagation across the salt layer and, in essence, allowing for a long‐living forced folding process. Our results indicate the important effect of along‐strike variation in displacement and displacement rates in controlling evaporite behaviour in extensional basins. Amount of displacement and displacement rates are key factors controlling the propagation of basement faults across evaporite layers. In addition, growth strata patterns are recognized as a powerful tool for constraining the up‐dip propagation history of basement faults in extensional fault‐related fold systems with intermediate décollement levels.