The PMTRAS Roll Aspect System on RHESSI

High-resolution solar hard X-ray imaging on the Reuven Ramaty High-Energy Solar Spectroscopic Imager (RHESSI) spacecraft is achieved by a set of rotating modulation collimators. The interpretation of the observed time-modulated X-ray flux in terms of high-resolution, accurately located images requires continuous, arc-minute roll aspect, which at present is provided by the `Photo-Multiplier Tube Roll Aspect System' (PMTRAS). This paper describes the PMTRAS operating principles, hardware implementation, calibration, performance and data analysis approach, with emphasis on its effect on RHESSI imaging.     

The Radiometric and Pointing Calibration of SECCHI COR1 on STEREO

COR1 is the innermost coronagraph of the Sun Earth Connection Coronal and Heliospheric Investigation (SECCHI) instrument suite aboard the twin Solar Terrestrial Relations Observatory (STEREO) spacecraft. The paired COR1 telescopes observe the white-light K-corona from 1.4 to 4 solar radii in a waveband 22.5 nm wide centered on the Hα line at 656 nm. An internal polarizer allows the measurement of both total and polarized brightness. The co-alignment of the two COR1 telescopes is derived from the star λ Aquarii for the Ahead spacecraft, and from an occultation of the Sun by the Moon for Behind. Observations of the planet Jupiter are used to establish absolute photometric calibrations for each telescope. The intercalibration of the two COR1 telescopes are compared using coronal mass ejection observations made early in the mission, when the spacecraft were close together. Comparisons are also made with the Solar and Heliospheric Observatory (SOHO) Large Angle and Spectrometric Coronagraph (LASCO) C2 and Mauna Loa Solar Observatory Mk4 coronagraphs.     

Polar Plume Anatomy: Results of a Coordinated Observation

On 7 and 8 March 1996, the SOHO spacecraft and several other space- and ground-based observatories cooperated in the most comprehensive observation to date of solar polar plumes. Based on simultaneous data from five instruments, we describe the morphology of the plumes observed over the south pole of the Sun during the SOHO observing campaign. Individual plumes have been characterized from the photosphere to approximately 15 R⊙ yielding a coherent portrait of the features for more quantitative future studies. The observed plumes arise from small (∼ 2-5 arc sec diameter) quiescent, unipolar magnetic flux concentrations, on chromospheric network cell boundaries. They are denser and cooler than the surrounding coronal hole through which they extend, and are seen clearly in both Feix and Fexii emission lines, indicating an ionization temperature between 1.0–1.5 x 10⁶ K. The plumes initially expand rapidly with altitude, to a diameter of 20–30 Mm about 30 Mm off the surface. Above 1.2 R⊙ plumes are observed in white light (as ‘coronal rays’) and extend to above 12 R⊙. They grow superradially throughout their observed height, increasing their subtended solid angle (relative to disk center) by a factor of ∼10 between 1.05 R⊙ and 4–5 R⊙ and by a total factor of 20–40 between 1.05 R⊙ and 12 R⊙. On spatial scales larger than 10 arc sec, plume structure in the lower corona (R < 1.3 R⊙) is observed to be steady-state for periods of at least 24 hours; however, on spatial scales smaller than 10 arc sec, plume XUV intensities vary by 10–20% (after background subtraction) on a time scale of a few minutes. (Dr. Hassler is now employed by Southwest Research Institute, Boulder, CO)     

The mass and position of possible past companions of the Sun

Stars usually form as members of binary or multiple star systems, and it is likely that the Sun was no exception. The mass and position of possible past companions of the Sun is determined by considering the orbital stability of the Solar System. This is achieved by considering the stability of critical three-body subsets comprising the sun-planet-companion star which must be stable if the Solar System is to remain stable as a whole.     

Calibrating the Pointing and Optical Parameters of the STEREO Heliospheric Imagers

The Heliospheric Imager (HI) instruments on the Solar TErrestrial RElations Observatory (STEREO) observe solar plasma as it streams out from the Sun and into the heliosphere. The telescopes point off-limb (from about 4° to 90° elongation) and so the Sun is not in the field of view. Hence, the Sun cannot be used to confirm the instrument pointing. Until now, the pointing of the instruments have been calculated using the nominal preflight instrument offsets from the STEREO spacecraft together with the spacecraft attitude data. This paper develops a new method for deriving the instrument pointing solutions, along with other optical parameters, by comparing the locations of stars identified in each HI image with the known star positions predicted from a star catalogue. The pointing and optical parameters are varied in an autonomous manner to minimise the discrepancy between the predicted and observed positions of the stars. This method is applied to all HI observations from the beginning of the mission to the end of April 2008. For the vast majority of images a good attitude solution has been obtained with a mean-squared deviation between the observed and predicted star positions of one image pixel or less. Updated values have been obtained for the instrument offsets relative to the spacecraft, and for the optical parameters of the HI cameras. With this method the HI images can be considered as “self-calibrating,” with the actual instrument offsets calculated as a byproduct. The updated pointing results and their by-products have been implemented in SolarSoft.     

Solar flux determination in the spectral range 150–210 nm

Solar irradiation fluxes are determined between 150 and 210 nm from stigmatic spectra of the Sun obtained by means of a rocket-borne spectrograph. Absolute intensities at the disk center with a spectral resolution of 0.04 nm and a spatial resolution of 7 arc sec are presented. From center-to-limb intensity variations determined from the same spectra, mean full disk intensities of the quiet Sun can be deduced. In order to compare them with other measurements, the new solar fluxes have been averaged over a bandpass of 1 nm.     

FIRST RESULTS OF THE SUMER TELESCOPE AND SPECTROMETER ON SOHO – II. Imagery and Data Management

SUMER – Solar Ultraviolet Measurements of Emitted Radiation – is not only an extreme ultraviolet (EUV) spectrometer capable of obtaining detailed spectra in the range from 500 to 1610 Å, but, using the telescope mechanisms, it also provides monochromatic images over the full solar disk and beyond, into the corona, with high spatial resolution. We report on some aspects of the observation programmes that have already led us to a new view of many aspects of the Sun, including quiet Sun, chromospheric and transition region network, coronal hole, polar plume, prominence and active region studies. After an introduction, where we compare the SUMER imaging capabilities to previous experiments in our wavelength range, we describe the results of tests performed in order to characterize and optimize the telescope under operational conditions. We find the spatial resolution to be 1.2 arc sec across the slit and 2 arc sec (2 detector pixels) along the slit. Resolution and sensitivity are adequate to provide details on the structure, physical properties, and evolution of several solar features which we then present. Finally some information is given on the data availability and the data management system.     

Absolute redshifts in the C iv 1548 Å line in the transition region of the quiet Sun

Observations with the UVSP instrument on the SMM spacecraft were made at the polar limb and disk center for the accurate determination of Doppler shifts of the Civ 1548 Å emission line formed at 10⁵ K in the transition region of the quiet Sun. Individual data points representing 3 arc sec square pixels yield both redshifts and blueshifts, but the mean values from four different days of observations are toward the red. The mean redshifts are in the range 4–8 km s^-1 and are produced by nearly vertically directed flows; the uncertainty associated with the mean values correspond to ±0.5 km s^-1. The redshift increases with brightness of the Civ line.     

Background Subtraction for the SECCHI/COR1 Telescope Aboard STEREO

COR1 is an internally occulted Lyot coronagraph, part of the Sun Earth Connection Coronal and Heliospheric Investigation (SECCHI) instrument suite aboard the twin Solar Terrestrial Relations Observatory (STEREO) spacecraft. Because the front objective lens is subjected to a full solar flux, the images are dominated by instrumental scattered light which has to be removed to uncover the underlying K corona data. We describe a procedure for removing the instrumental background from COR1 images. F coronal emission is subtracted at the same time. The resulting images are compared with simultaneous data from the Mauna Loa Solar Observatory Mk4 coronagraph. We find that the background subtraction technique is successful in coronal streamers, while the baseline emission in coronal holes (i.e. between plumes) is suppressed. This is an expected behavior of the background subtraction technique. The COR1 radiometric calibration is found to be either 10 – 15% lower, or 5 – 10% higher than that of the Mk4, depending on what value is used for the Mk4 plate scale, while an earlier study found the COR1 radiometric response to be ∼ 20% higher than that of the Large Angle Spectroscopic Coronagraph (LASCO) C2 telescope. Thus, the COR1 calibration is solidly within the range of other operating coronagraphs. The background levels in both COR1 telescopes have been quite steady in time, with the exception of a single contamination event on 30 January 2009. Barring too many additional events of this kind, there is every reason to believe that both COR1 telescopes will maintain usable levels of scattered light for the remainder of the STEREO mission.     

Observations of the longitudinal magnetic field in the transition region and photosphere of a sunspot

The Ultraviolet Spectrometer and Polarimeter on the Solar Maximum Mission spacecraft has observed for the first time the longitudinal component of the magnetic field by means of the Zeeman effect in the transition region above a sunspot. The data presented here were obtained on three days in one sunspot, have spatial resolutions of 10 arc sec and 3 arc sec, and yield maximum field strengths greater than 1000 G above the umbrae in the spot. The method of analysis, including a line-width calibration feature used during some of the observations, is described in some detail in an appendix; the line width is required for the determination of the longitudinal magnetic field from the observed circular polarization.The transition region data for one day are compared with photospheric magnetograms from the Marshall Space Flight Center. Vertical gradients of the magnetic field are computed from the two sets of data; the maximum gradients of 0.41 to 0.62 G km^–1 occur above the umbra and agree with or are smaller than values observed previously in the photosphere and low chromosphere.     

Weak-Field Magnetogram Calibration using Advanced Stokes Polarimeter Flux-Density Maps – I. Solar Optical Universal Polarimeter Calibration

Cotemporal Fei 630.2 nm magnetograms from the Solar Optical Universal Polarimeter (SOUP) filter and the Advanced Stokes Polarimeter (ASP) are quantitatively compared using observations of active region AR 8218, a large negative polarity sunspot group observed at S20 W22 on 13 May 1998. The SOUP instrument produces Stokes V/I `filter magnetograms' with wide field of view and spatial resolution below 0.5 arc sec in good seeing, but low spectral resolution. In contrast, the ASP uses high spectral resolution to produce very high-precision vector magnetic field maps at spatial resolution values on the order of 1 arc sec in good seeing. We use ASP inversion results to create an ASP `longitudinal magnetic flux-density map' with which to calibrate the less precise SOUP magnetograms. The magnetograms from each instrument are co-aligned with an accuracy of about 1 arc sec. Regions of invalid data, poor field-of-view overlap, and sunspots are masked out in order to calibrate SOUP predominately on the relatively vertical `weak-field' plage magnetic elements. Pixel-to-pixel statistical comparisons are used to determine the SOUP magnetogram linear calibration constant relative to ASP flux-density values. We compare three distinct methods of scaling the ASP and SOUP data to a common reference frame in order to explore filling factor effects. The recommended SOUP calibration constant is 17000 ± 550 Mx cm^–2 per polarization percent in plage regions. We find a distinct polarity asymmetry in SOUP response relative to the ASP, apparently due to a spatial resolution effect in the ASP data: the smaller, less numerous, minority polarity structures in the plage region are preferentially blended with the majority polarity structures. The blending occurs to a lesser degree in the high-resolution SOUP magnetogram thus leading to an apparent increase in SOUP sensitivity to the minority polarity structures relative to the ASP. One implication of this effect is that in mixed polarity regions on the Sun, lower spatial resolution magnetograms may significantly underestimate minority polarity flux levels, thus leading to apparent flux imbalances in the data. ^*Visiting Astronomer, National Solar Observatory, operated by the Association of Universities for Research in Astronomy, Inc. (AURA), under cooperative agreement with the National Science Foundation. The National Center for Atmospheric Research is sponsored by the National Science Foundation.     

EUV Full-Sun Imaging and Pointing Calibration of the SOHO Coronal Diagnostic Spectrometer

Although the field of view of the Normal Incidence Spectrometer (NIS) of the Coronal Diagnostic Spectrometer (CDS) is 4×4 arc min, it is possible to observe the full solar disk by forming a mosaic of images taken in succession. This paper describes just such a study which has been used to collect images of the Sun simultaneously in six wavelengths between 304 Ú and 630 Ú, and with a temperature coverage between 5×10⁴ K and 2.5×10⁶ K. A representative sample of the resulting images is presented. These data can be used to explore the origin of solar EUV variability, and examine large-scale solar features. Another use of these data is to calibrate the pointing of the CDS Offset Pointing System (OPS), by comparing them against the SOHO Extreme ultraviolet Imaging Telescope (EIT) full-disk images taken at the same time. Many joint observations are made with CDS and other SOHO instruments, and calibration of the pointing is crucial to the co-pointing of the instruments, and to the analyses of these data. Coalignment is done by fitting to a cross-correlation function, using an IDL procedure which can be applied to any CDS/NIS data set. The accuracy of an individual coalignment can be demonstrated to be in the range 1–2 arc sec. The overall accuracy of the OPS calibration is ±5 arc sec, mainly attributable to measurement error in the actuator positions. An onboard Spartan Intermediate Sun Sensor of the Lockheed design, which was intended to provide greater pointing accuracy, exhibits a time-varying calibration, possibly due to a gradual loss of sensitivity.     

The relativistic factor in the orbital dynamics of point masses

There is a growing population of relativistically relevant minor bodies in the Solar System and a growing population of massive extrasolar planets with orbits very close to the central star where relativistic effects should have some signature. Our purpose is to review how general relativity affects the orbital dynamics of the planetary systems and to define a suitable relativistic correction for Solar System orbital studies when only point masses are considered. Using relativistic formulae for the N body problem suited for a planetary system given in the literature we present a series of numerical orbital integrations designed to test the relevance of the effects due to the general theory of relativity in the case of our Solar System. Comparison between different algorithms for accounting for the relativistic corrections are performed. Relativistic effects generated by the Sun or by the central star are the most relevant ones and produce evident modifications in the secular dynamics of the inner Solar System. The Kozai mechanism, for example, is modified due to the relativistic effects on the argument of the perihelion. Relativistic effects generated by planets instead are of very low relevance but detectable in numerical simulations.     

The Solar Wind at 1 AU During the Declining Phase of Solar Cycle 23: Comparison of 3D Numerical Model Results with Observations

We present results of solar-wind parameters generated by 3D MHD models. The ENLIL inner-heliosphere solar-wind model together with the MAS or Wang – Sheeley – Arge (WSA) coronal models, describe the steady solar-wind stream structure and its origins in the solar corona. The MAS/ENLIL and WSA/ENLIL models have been tuned to provide a simulation of plasma moments as well as interplanetary magnetic-field magnitude and polarity in the absence of disturbances from coronal transients. To investigate how well the models describe the ambient solar wind structure from the Sun out to 1 AU, the model results are compared to solar-wind measurements from the ACE spacecraft. We find that there is an overall agreement between the observations and the model results for the general large-scale solar-wind structures and trends, such as the timing of the high-density structures and the low- and high-speed winds, as well as the magnetic sector structures. The time period of our study is the declining phase of Solar Cycle 23 when the solar activity involves well-defined stream structure, which is ideal for testing a quasi-steady-state solar-wind model.     

The Ultraviolet Spectrometer and Polarimeter on the Solar Maximum Mission

The Ultraviolet Spectrometer and Polarimeter (UVSP) on the Solar Maximum Mission spacecraft is described, including the experiment objectives, system design, performance, and modes of operation. The instrument operates in the wavelength range 1150–3600 Å with better than 2 arc sec spatial resolution, raster range 256 × 256 arc sec², and 20 mÅ spectral resolution in second order. Observations can be made with specific sets of 4 lines simultaneously, or with both sides of 2 lines simultaneously for velocity and polarization. A rotatable retarder can be inserted into the spectrometer beam for measurement of Zeeman splitting and linear polarization in the transition region and chromosphere.Currently at MMTO, University of Arizona, Tucson, Ariz. 85721, U.S.A.     

Radio emission from the Sun at 843 MHz

The Molonglo Observatory Synthesis Telescope (MOST) has recently been modified to permit observations of the Sun. With a collecting area of 18000 m², MOST makes high-sensitivity measurements in right-hand circular polarisation over a 3 MHz bandwidth at 843 MHz. The maximum baseline of the multi-element interferometer is 1600 m, so that one-dimensional spatial resolution as fine as 32 arc sec is available. A resistor array produces simultaneously a set of 64 beams separated by 22 arc sec, which may be offset electronically to cover the entire Sun in a few seconds. Observations may be made with a beam shape corresponding to either a multiplying or an adding interferometer. By exploiting the technique of Earth-rotation synthesis the telescope may be used to make two-dimensional maps of the Sun at the time of the austral solstice with a synthesized beamwidth of 43 × 110 arc sec. This paper describes the instrument and the procedures used to make various types of solar observations, and exhibits some of the first data collected.     

The RHESSI Imaging Concept

The Reuven Ramaty High-Energy Solar Spectroscopic Imager (RHESSI) observes solar hard X-rays and gamma-rays from 3 keV to 17 MeV with spatial resolution as high as 2.3 arc sec. Instead of focusing optics, imaging is based on nine rotating modulation collimators that time-modulate the incident flux as the spacecraft rotates. Starting from the arrival time of individual photons, ground-based software then uses the modulated signals to reconstruct images of the source. The purpose of this paper is to convey both an intuitive feel and the mathematical basis for this imaging process. Following a review of the relevant hardware, the imaging principles and the basic back-projection method are described, along with their relation to Fourier transforms. Several specific algorithms (Clean, MEM, Pixons and Forward-Fitting) applicable to RHESSI imaging are briefly described. The characteristic strengths and weaknesses of this type of imaging are summarized.     

The Reuven Ramaty High-Energy Solar Spectroscopic Imager (RHESSI)

RHESSI is the sixth in the NASA line of Small Explorer (SMEX) missions and the first managed in the Principal Investigator mode, where the PI is responsible for all aspects of the mission except the launch vehicle. RHESSI is designed to investigate particle acceleration and energy release in solar flares, through imaging and spectroscopy of hard X-ray/gamma-ray continua emitted by energetic electrons, and of gamma-ray lines produced by energetic ions. The single instrument consists of an imager, made up of nine bi-grid rotating modulation collimators (RMCs), in front of a spectrometer with nine cryogenically-cooled germanium detectors (GeDs), one behind each RMC. It provides the first high-resolution hard X-ray imaging spectroscopy, the first high-resolution gamma-ray line spectroscopy, and the first imaging above 100 keV including the first imaging of gamma-ray lines. The spatial resolution is as fine as ∼ 2.3 arc sec with a full-Sun (≳ 1°) field of view, and the spectral resolution is ∼ 1–10 keV FWHM over the energy range from soft X-rays (3 keV) to gamma-rays (17 MeV). An automated shutter system allows a wide dynamic range (>10⁷) of flare intensities to be handled without instrument saturation. Data for every photon is stored in a solid-state memory and telemetered to the ground, thus allowing for versatile data analysis keyed to specific science objectives. The spin-stabilized (∼ 15 rpm) spacecraft is Sun-pointing to within ∼ 0.2° and operates autonomously. RHESSI was launched on 5 February 2002, into a nearly circular, 38° inclination, 600-km altitude orbit and began observations a week later. The mission is operated from Berkeley using a dedicated 11-m antenna for telemetry reception and command uplinks. All data and analysis software are made freely and immediately available to the scientific community. Supplementary material to this paper is available in electronic form at http://dx.doi.org/10.1023/A:1022428818870     

Protostellar angular momentum transport by spiral density waves

The gravitational collapse of molecular clouds or cloud cores is expected to lead to the formation of stars that begin their lives in a state of rapid rotation. It is known that, in at least some specific cases, rapidly rotating, slf-gravitating bodies are subject to instabilities that cause them to assume ellipsoidal shapes. In this paper we investigate the consequences of such instabilities on the angular momentum evolution of a star in the process of formation from a collapsing cloud, and surrounded by a protostellar disk, with a view toward applications to the formation of the Solar System. We use a specific model of star formation to demonstrate the possibility that such a star would become unstable, that the resulting distortion of the star would generate spiral density waves in the circumstellar disk, and that the torque associated with these waves would regulate the angular momentum of the star as it feeds angular momentum to the disk. We conclude that the angular momentum so transported to the disk would not spread the disk to, say, Solar System dimensions, by the action of the spiral density waves alone. However, a viscous disk could effectively extract stellar angular momentum and attain Solar System size. Our results also indicate that viscous disks could feed mass and angular momentum to a growing protostar in such a manner that distortions of the star would occur before gravitational torques could balance the influx of angular momentum. In other situations (in which the viscosity was small), a gap could be cleared between the disk and star.     

The sun‐as‐a‐star solar spectrum

The Sun is the only star for which individual surface features can be observed directly. For other stars, the properties of starspots, stellar rotation, stellar flares, etc, are derived indirectly via variation of star‐integrated spectral line profiles or their luminosity measurements. Solar disk‐integrated and disk‐resolved observations allow for investigations of the contribution of individual solar disk features to sun‐as‐a‐star spectra. Here, we provide a brief overview of three sun‐as‐a‐star programs, currently in operation, and describe recent improvements in observations and data reduction for the Integrated Sunlight Spectrometer (ISS), one of three instruments comprising the Synoptic Optical Long‐term Investigations of the Sun (SOLIS) system. Next, we discuss studies employing sun‐as‐a‐star observations (including Ca II K line as proxy for total unsigned magnetic flux and 2800 MHz radio flux) as well as the effects of flares on solar disk‐integrated spectra. (© 2014 WILEY‐VCH Verlag GmbH & Co. KGaA, Weinheim)