High and very high resolution deep-towed seismic system: Performance and examples from deep water Geohazard studies

We present the technological development and initial results from the deep-towed seismic acquisition device SYstème SIsmique Fond de mer (SYSIF) recently built by Ifremer. The two configurations of the SYSIF are presented (high resolution (HR): 250–1000 Hz and very high resolution (VHR): 650–2000 Hz), and results are compared to conventional seismic acquisition systems such as multi-channel HR or single-channel VHR (hull-mounted sub-bottom profiler). The ability of SYSIF to achieve higher resolution imagery is due to both the technology employed (low-frequency Janus–Helmoltz piezoelectric transducer) and the deep-towed operating mode (reduction in the Fresnel zone). Sea trials have been conducted in various geological environments and in water depths as deep as 2500 m. The new technique improved imaging of deep seafloor and sub-surface features such as pockmarks, carbonate mounds, sub-marine slides and sub-surface faulting. SYSIF, therefore, is a well-suited tool to investigate deep water geological features, especially those related to geohazard for scientific and industrial purposes.     

Pasisar: Performances of a High and Very High Resolution Hybrid Deep-Towed Seismic Device

The Pasisar seismic acquisition system combines a source at the sea surface and a deep-towed single channel streamer. This unconventional device geometry reduces the width of the first Fresnel zone which increases the lateral resolution. However, the device acquisition geometry generates artifacts on seismic profiles and induces large incidence angles of the seismic signal. A specific processing sequence must be applied to the data to obtain a readable seismic section. Penetration of the seismic signal depends on the energy of the signal reaching the seafloor and on its incidence angle. Because of smaller source energy, 800 Joules Sparker data cannot be acquired in water depth larger than 1500 m for example, whereas there is no depth limit for the use of this system with air gun sources. Differential acoustic absorption of seismic frequencies (below 1000 Hz) in the water column is negligible when compared with wave fronts expansion. Thus, the horizontal resolution of any seismic system strongly depends on the frequency spectrum of the seismic source and on the travel distances. Pasisar and conventional seismic profiles being usually simultaneously recorded, we illustrate the interest of using a hybrid seismic device by comparing horizontal resolutions as well as signal-to-noise ratio obtained with both the Pasisar and conventional systems. In addition, by carefully picking time arrivals of a reflection on simultaneously recorded surface and deep-towed seismic records, it is possible to estimate the average interval seismic velocity. We present the simplified example of a horizontal reflector.     

Deep penetrating benthic oxygen profiles measured in situ by oxygen optodes

For the first time in situ, deep penetrating O₂ profiles were measured in abyssal sediments in the western South Atlantic. Construction of deep penetrating O₂ optodes and adaptation to a benthic profiling lander are described. The opto-chemical oxygen sensors allow measurements to a depth of 55 cm in marine sediments. A vertical resolution of 0.5 cm was used to determine the O₂ dynamics in those oligotrophic deep sea sediments; the oxygen concentration across the sediment water interface was measured with a resolution of 100 μm. Oxygen penetration depth (OPD), diffusive oxygen uptake (DOU) and oxygen consumption rates were determined at four stations north of the Amazon fan and one at the Mid-Atlantic Ridge. Diffusive oxygen uptake rates ranged from 0.1 to 0.9 mmol m⁻² d⁻¹; the oxygen penetration depth ranged from 8 to 26 cm. Carbon consumption rates calculated from the diffusive oxygen uptake rates were in the range of 0.3–3.0 g C m⁻² a⁻¹. Comparison between in situ and laboratory DOU and OPD measurements confirmed previous findings that core recovery and warming have strong effects on the oxygen dynamics in deep sea sediments. Laboratory measurements yielded a decrease of 50–75% in OPD and consequently an increase in DOU by 1.5 and 18-times. Deep penetrating oxygen optodes provide a new tool to accurately determine oxygen dynamics (and thereby calculate carbon mineralization rates) in oligotrophic sediments. However, oxygen optodes as used in this study do not resolve the diffusive boundary layer (DBL). The data show that deep penetrating O₂ optodes in combination with high-resolution O₂ microelectrodes give a complete picture of the oxygen dynamics, including the DBL, in deep sea sediments.     

How does multiscale modelling and inclusion of realistic palaeobathymetry affect numerical simulation of the Storegga Slide tsunami?

The ∼8.15 ka Storegga submarine slide was a large (∼3000 km³), tsunamigenic slide off the coast of Norway. The resulting tsunami had run-up heights of around 10–20 m on the Norwegian coast, over 12 m in Shetland, 3–6 m on the Scottish mainland coast and reached as far as Greenland. Accurate numerical simulations of Storegga require high spatial resolution near the coasts, particularly near tsunami run-up observations, and also in the slide region. However, as the computational domain must span the whole of the Norwegian-Greenland sea, employing uniformly high spatial resolution is computationally prohibitive. To overcome this problem, we present a multiscale numerical model of the Storegga slide-generated tsunami where spatial resolution varies from 500 m to 50 km across the entire Norwegian-Greenland sea domain to optimally resolve the slide region, important coastlines and bathymetric changes. We compare results from our multiscale model to previous results using constant-resolution models and show that accounting for changes in bathymetry since 8.15 ka, neglected in previous numerical studies of the Storegga slide-tsunami, improves the agreement between the model and inferred run-up heights in specific locations, especially in the Shetlands, where maximum run-up height increased from 8 m (modern bathymetry) to 13 m (palaeobathymetry). By tracking the Storegga tsunami as far south as the southern North sea, we also found that wave heights were high enough to inundate Doggerland, an island in the southern North Sea prior to sea level rise over the last 8 ka.     

Continuous measurement of an artificial upwelling of deep sea water induced by the perpetual salt fountain

A perpetual salt fountain can draw up deep sea water without any artificial energy source. This is one of the ideal ways to draw up deep sea water for nutrient enhancement application. A perpetual salt fountain experiment was carried out in May 2004. The estimated average velocity of the upwelling after 48 h from the start of the experiment was about 7 mm/s, and it continued for about 3 days. The flow rate with a single pipe was estimated as approximately 45 m³/day. The amount of upwelled deep sea water by this single pipe seems too small to be of benefit, but we can easily increase the amount by deploying a number of pipes.     

Bioluminescence in the deep sea: Free-fall lander observations in the Atlantic Ocean off Cape Verde

A novel autonomous free-fall lander vehicle, with a capability down to 6000 m, was deployed off Cape Verde for studies on bioluminescence in the deep sea. The system was equipped with a high-sensitivity Intensified Silicon Intensified Target (ISIT) video camera, a programmable control-recording unit and an acoustic current meter with depth and temperature sensors. The ISIT lander was used in three modes: (1) free falling at 34 m min⁻¹, with the camera looking downwards at a mesh screen, recording impacts of luminescent organisms to obtain a vertical profile down to the abyssal sea floor, sampling at >100 l s⁻¹; (2) rotating, with the lander on the sea floor and the camera orienting to the bottom current using a servo-controlled turntable, impacts of luminescent organisms carried by the bottom current onto a mesh screen mounted 0.5 m in front of the camera were recorded to estimate abundance in the benthic boundary layer; (3) baited, with the camera focused on a bait placed on the sea floor.Profiles recorded abundance of luminescent organisms as 26.7 m⁻³ at 500–999 m depth, decreasing to 1.6 m⁻³ at 2000–2499 m and 0.5 m⁻³ between 2500 m and the sea floor at 4046 m, with no further detectable significant change with depth. Rotator measurements at a 0.5 m height above the sea floor gave a mean abundance of 0.47 m⁻³ in the benthic boundary layer at 4046 m and of 2.04 m⁻³ at 3200 m. Thirty five minutes after the bait was placed on the sea floor at 3200 m, bioluminescent fauna apparently arrived at the bait and produced luminescent displays at a rate of 2 min⁻¹. Moving, flashing light sources were observed and luminescent material was released into the bottom current.     

DOC dynamics in the meso and bathypelagic layers of the Mediterranean Sea

Seven years (2001–2008) of dissolved organic carbon (DOC) vertical profiles were examined in order to assess the main processes determining DOC concentration and distribution in the meso- and bathypelagic layers of the Mediterranean Sea. As expected, DOC showed high and highly variable concentrations in the surface layer of 57–68 μM (average values between 0 and 100 m), with a decrease to 44–53 μM between 200 and 500 m. Deep DOC distribution was strongly affected by deep-water formation, with a significant increase to values of 76 μM in recently ventilated deep waters, and low concentrations, comparable to those observed in the open oceanic waters (34–45 μM), where the oldest, deep waters occurred. In winter 2004/2005 a deep-water formation event was observed and the consequent DOC export at depth was estimated to range between 0.76–3.02 Tg C month^–1. In the intermediate layer, the main path of the Levantine Intermediate Water (LIW) was followed in order to estimate the DOC consumption rate in its core. Multiple regression between DOC, apparent oxygen utilization (AOU), and salinity indicated that 38% of the oxygen consumption was related to DOC mineralization when the effect of mixing was removed. In deep waters of the southern Adriatic Sea a DOC decrease of 6 μM, together with an AOU increase of 9 μM, was observed between the end of January 2008 and the end of June 2008 (5 months). These data indicate a rate of microbial utilization of DOC of about 1.2 μM C month⁻¹, with 92% of the oxygen consumption due to DOC mineralization. These values are surprisingly high for the deep sea and represent a peculiarity of the Mediterranean Sea.     

A high-resolution seismic profiling system using a deep-towed horizontal hydrophone streamer

A seismic reflection profiling system utilising a surface air gun source and a deep-towed horizontal hydrophone streamer has been developed for high resolution studies in the deep ocean. The instrument is deployed on a conventional armoured single conductor cable at depths of up to 6 km. Seismic data from the 30 m long streamer is wide-band frequency modulated up the towing cable to the ship together with a high frequency monitor from a 3.5 kHz echo-sounder mounted on the instrument package. The geometry of the system allows an order of magnitude improvement in spatial resolution compared with that obtained from standard surface source/receiver configurations. The summed hydrophones of the streamer attenuate cable-generated mechanical noise, and the 3.5 kHz sea-surface and bottom reflected returns provide receiver positioning information. The system has been successfully deployed at depths of 5 km in the Vema Fracture Zone in the North Atlantic, and although initially difficulties were experienced in balancing the streamer, subsequent profiles across the transform fault show details of sub-bottom structure which on conventional surface records are generally masked by diffraction hyperbolae.     

The deep-water motion through the Lifamatola Passage and its contribution to the Indonesian throughflow

In order to estimate the contribution of cold Pacific deep water to the Indonesian throughflow (ITF) and the flushing of the deep Banda Sea, a current meter mooring has been deployed for nearly 3 years on the sill in the Lifamatola Passage as part of the International Nusantara Stratification and Transport (INSTANT) programme. The velocity, temperature, and salinity data, obtained from the mooring, reflect vigorous horizontal and vertical motion in the lowest 500 m over the ～2000 m deep sill, with speeds regularly surpassing 100 cm/s. The strong residual flow over the sill in the passage and internal, mainly diurnal, tides contribute to this bottom intensified motion. The average volume transport of the deep throughflow from the Maluku Sea to the Seram Sea below 1250 m is 2.5 Sv (1 Sv=10⁶ m³/s), with a transport-weighted mean temperature of 3.2 °C. This result considerably increases existing estimates of the inflow of the ITF into the Indonesian seas by about 25% and lowers the total mean inflow temperature of the ITF to below 13 °C. At shallower levels, between 1250 m and the sea surface, the flow is directed towards the Maluku Sea, north of the passage. The typical residual velocities in this layer are low (～3 cm/s), contributing to an estimated northward flow of 0.9–1.3 Sv. When more results from the INSTANT programme for the other Indonesian passages become available, a strongly improved estimate of the mass and heat budget of the ITF becomes feasible.     

海洋多道地震拖缆数据实时传输系统的设计与实现

为满足深拖式高分辨多道地震勘探需求,设计并实现了海洋地震拖缆数据的实时传输系统。系统由数传包与地震采集站连接组成,采用推荐标准485(Recommended Standards 485,RS485)串行总线实现了采集站与数传包的物理连接,利用低电压差分信号(Low-Voltage Differential Signaling,LVDS)、预加重/均衡器、8位/10位(8 bit/10 bit)编码等技术实现了数传包之间的通信链路。设计了无等待反馈重传的差错控制方法,提高系统高效性和可靠性;在现场可编程门阵列(Field Programmable Gate Array,FPGA)内部采用先进先出(First Input First Output,FIFO)构建多优先级任务队列的多级流水线设计,解决了大容量数据并发而产生的数据漏帧问题。在实验室用已知正弦信号对系统进行了对比测试,结果表明系统能够满足海洋多道地震勘探的数据传输需求,对于海洋多道高分辨率地震资料的可靠获取具有重要的意义。     

Deep Caribbean Sea warming

Data collected from hydrographic stations occupied within the Venezuelan and Columbian basins of the Caribbean Sea from 1922 through 2003 are analyzed to study the decadal variability of deep temperature in the region. The analysis focuses on waters below the 1815-m sill depth of the Anegada–Jungfern Passage. Relatively dense waters (compared to those in the deep Caribbean) from the North Atlantic spill over this sill to ventilate the deep Caribbean Sea. Deep warming at a rate of over 0.01 °C decade^–1 below this sill depth appears to have commenced in the 1970s after a period of relatively constant deep Caribbean Sea temperatures extending at least as far back as the 1920s. Conductivity–temperature–depth station data from World Ocean Circulation Experiment Section A22 along 66°W taken in 1997 and again in 2003 provide an especially precise, albeit geographically limited, estimate of this warming over that 6-year period. They also suggest a small (0.001 PSS-78, about the size of expected measurement biases) deep freshening. The warming is about 10 times larger than the size of geothermal heating in the region, and is of the same magnitude as the average global upper-ocean heat uptake over a recent 50-year period. Together with the freshening, the warming contributes about 0.012 m decade^–1 of sea level rise in portions of the Caribbean Sea with bottom depths around 5000 m.     

Sulfate reduction in Black Sea sediments: in situ and laboratory radiotracer measurements from the shelf to 2000 m depth

Sulfate reduction rate measurements by the ³⁵SO₄²⁻ core injection method were carried out in situ with a benthic lander, LUISE, and in parallel by shipboard incubations in sediments of the Black Sea. Eight stations were studied along a transect from the Romanian shelf to the deep western anoxic basin. The highest rates measured on an areal basis for the upper 0–15 cm were 1.97 mmol m⁻² d⁻¹ on the shelf and 1.54 mmol m⁻² d⁻¹ at 181 m water depth just below the chemocline. At all stations sulfate reduction rates decreased to values <3 nmol cm⁻³ d⁻¹ below 15 cm depth in the sediment. The importance of sulfate reduction relative to the total mineralization of organic matter was very low, 6%, on the inner shelf, which was paved with mussels, and increased to 47% on the outer shelf at 100 m depth. Where the oxic–anoxic interface of the water column impinged on the sea floor at around 150 m depth, the contribution of sulfate reduction increased from >50% just above the chemocline to 100% just below. In the deep sea, mean sulfate reduction rates were 0.6 mmol m⁻² d⁻¹ corresponding to an organic carbon oxidation of 1.3 mmol m⁻² d⁻¹. This is close to the mean sedimentation rate of organic carbon over the year in the western basin. A comparison with published data on sulfate reduction in Black Sea sediments showed that the present results tend to be higher in shelf sediments and lower in the deep-sea than most other data. Based on the present water column H₂S inventory and the H₂S flux out of the sediment, the calculated turnover time of H₂S below the chemocline is 2100 years.     

Structure of potential upwelling areas in the Philippines

The three-dimensional structure of two potential mesoscale upwelling areas that are located in the external waters of the Philippine archipelago (i.e. northwest of Luzon and east of Mindanao) were constructed by analysis of historical data. A unique characteristic of both upwelling sites is that they can be identified by their anomalously cold subsurface temperatures rather than sea surface temperature distributions. As such, they cannot be observed in sea surface temperature fields derived by satellite imagery. The data used in the analysis were obtained from the National Oceanographic Data Center hydrographic database. Objective analysis was performed to produce monthly temperature fields at several standard depths within the upper 500 m of the region 0–30°N and 100–140°E with a horizontal grid resolution of 0.5°. The extent and timing of these upwelling areas are described. A review of existing hypothesis on the mechanisms for their evolution and seasonal modulation are presented. The change in heat content during the upwelling season is greater than 300 W m⁻² in both areas. Based on the excursion of isotherms, vertical velocities of 83 cm day⁻¹ and 26 cm day⁻¹ were obtained for upwelling northwest of Luzon and east of Mindanao, respectively.     

A wideband connection to sperm whales: A fiber-optic,deep-sea hydrophone array

A 10-element, 950 m long, vertical hydrophone array based on fiber-optic data transmission has been developed primarily for studying the beam pattern from deep diving cetaceans emitting sonar pulses. The array elements have a configurable sampling rate and resolution with a maximum signal bandwidth of 90 kHz and a maximum dynamic range of 133 dB. The array has been deployed from a 14 m ketch with a crew of four. In the course of the development a number of mechanical and electrical problems have been solved.     

Persian Gulf response to a wintertime shamal wind event

The results from a～1 km resolution HYbrid Coordinate Ocean Model (HYCOM), forced by 1/2° Navy Operational Global Atmospheric Prediction System (NOGAPS) atmospheric data, were used in order to study the dynamic response of the Persian Gulf to wintertime shamal forcing. Shamal winds are strong northwesterly winds that occur in the Persian Gulf area behind southeast moving cold fronts. The period from 20 November to 5 December 2004 included a well defined shamal event that lasted 4–5 days. In addition to strong winds (16 m s^?1) the winter shamal also brought cold dry air (T_a=20 °C, q_a=10 g kg^?1) which led to a net heat loss in excess of 1000 W m^?2 by increasing the latent heat flux. This resulted in SST cooling of up to 10 °C most notably in the northern and shallower shelf regions. A sensitivity experiment with a constant specific humidity of q_a=15 g kg^?1 confirmed that about 38% of net heat loss was due to the air–sea humidity differences. The time integral of SST cooling closely followed the air–sea heat loss, indicating an approximate one-dimensional vertical heat balance. It was found that the shamal induced convective vertical mixing provided a direct mechanism for the erosion of stratification and deepening of the mixed layer by 30 m. The strong wind not only strengthened the circulation in the entire Persian Gulf but also established a northwestward flowing Iranian Coastal Current (ICC, 25–30 cm s^?1) from the Strait of Hormuz to about 52°E, where it veered offshore. The strongest negative sea level of 25–40 cm was generated in the northernmost portion of the Gulf while the wind setup against the coast of the United Arab Emirates established a positive sea level of 15–30 cm. The transport through the Strait of Hormuz at 56.2°E indicated an enhanced outflow of 0.25 Sv (Sv≡10⁶ m³ s^?1) during 24 November followed by an equivalent inflow on the next day.     

Salt diapirs in the Dead Sea basin and their relationship to Quaternary extensional tectonics

Regional extension of a brittle overburden and underlying salt causes differential loading that is thought to initiate the rise of reactive diapirs below and through regions of thin overburden. We present a modern example of a large salt diapir in the Dead Sea pull-apart basin, the Lisan diapir, which we believe was formed during the Quaternary due to basin transtension and subsidence. Using newly released seismic data that are correlated to several deep wells, we determine the size of the diapir to be 13×10 km, its maximum depth 7.2 km, and its roof 125 m below the surface. From seismic stratigraphy, we infer that the diapir started rising during the early to middle Pleistocene as this section of the basin underwent rapid subsidence and significant extension of the overburden. During the middle to late Pleistocene, the diapir pierced through the extensionally thinned overburden, as indicated by rim synclines, which attest to rapid salt withdrawal from the surrounding regions. Slight positive topography above the diapir and shallow folded horizons indicate that it is still rising intermittently. The smaller Sedom diapir, exposed along the western bounding fault of the basin is presently rising and forms a 200 m-high ridge. Its initiation is explained by localized E–W extension due monoclinal draping over the edge of a rapidly subsiding basin during the early to middle Pleistocene, and its continued rise by lateral squeezing due to continued rotation of the Amazyahu diagonal fault.     

Seismic survey noise disrupted fish use of a temperate reef

Marine seismic surveying discerns subsurface seafloor geology, indicative of, for example, petroleum deposits, by emitting high-intensity, low-frequency impulsive sounds. Impacts on fish are uncertain. Opportunistic monitoring of acoustic signatures from a seismic survey on the inner continental shelf of North Carolina, USA, revealed noise exceeding 170 dB re 1 μ Pa peak on two temperate reefs federally designated as Essential Fish Habitat 0.7 and 6.5 km from the survey ship path. Videos recorded fish abundance and behavior on a nearby third reef 7.9 km from the seismic track. During seismic surveying, reef-fish abundance declined by 78% during evening hours when fish habitat use was highest on the previous three days without seismic noise. Despite absence of videos documenting fish returns after seismic surveying, the significant reduction in fish occupation of the reef represents disruption to daily pattern. This numerical response confirms that conservation concerns associated with seismic surveying are realistic.     

Carbon and biogenic silica export influenced by the Amazon River Plume: Patterns of remineralization in deep-sea sediments

The Amazon River Plume delivers freshwater and nutrients to an otherwise oligotrophic western tropical North Atlantic (WTNA) Ocean. Plume waters create conditions favorable for carbon and nitrogen fixation, and blooms of diatoms and their diazotrophic cyanobacterial symbionts have been credited with significant CO₂ uptake from the atmosphere. The fate of the carbon, however, has been measured previously by just a few moored or drifting sediment traps, allowing only speculation about the full extent of the plume's impact on carbon flux to the deep sea. Here, we used surface (0.5 m) sediment cores collected throughout the Demerara Slope and Abyssal Plain, at depths ranging from 1800 to 5000 m, to document benthic diagenetic processes indicative of carbon flux. Pore waters were extracted from sediments using both mm- and cm-scale extraction techniques. Profiles of nitrate (NO₃) and silicate (Si(OH)₄) were modeled with a diffusion-reaction equation to determine particulate organic carbon (POC) degradation and biogenic silica (bSi) remineralization rates. Model output was used to determine the spatial patterns of POC and bSi arrival at the sea floor. Our estimates of POC and Si remineralization fluxes ranged from 0.16 to 1.92 and 0.14 to 1.35 mmol m⁻² d⁻¹, respectively. A distinct axis of POC and bSi deposition on the deep sea floor aligned with the NW axis of the plume during peak springtime flood. POC flux showed a gradient along this axis with highest fluxes closest to the river mouth. bSi had a more diffuse zone of deposition and remineralization. The impact of the Amazon plume on benthic fluxes can be detected northward to 10°N and eastward to 47°W, indicating a footprint of nearly 1 million km². We estimate that 0.15 Tmol C y⁻¹ is remineralized in abyssal sediments underlying waters influenced by the Amazon River. This constitutes a relatively high fraction (~7%) of the estimated C export from the region.; the plume thus has a demonstrable impact on C_org export in the western Atlantic. Benthic fluxes under the plume were comparable to and in some cases greater than those observed in the eastern equatorial Atlantic, the southeastern Atlantic, and the Southern Ocean.     

Lithogenic and biogenic particle fluxes on the Lomonosov Ridge (central Arctic Ocean) and their relevance for sediment accumulation: Vertical vs. lateral transport

Investigations of lithogenic and biogenic particle fluxes using long-term sediment traps are still very rare in the northern high latitudes and are restricted to the arctic marginal seas and sub-arctic regions. Here data on the variability of fluxes of lithogenic matter, CaCO₃, opal, and organic carbon and biomarker composition from the central Arctic Ocean are presented for a 1-year period. The study was carried out on material obtained from a long-term mooring system equipped with two multi-sampling traps, at 150 and 1550 m depth, and deployed on the southern Lomonosov Ridge close to the Laptev Sea continental margin from September 1995 to August 1996. In addition, data from surface sediments were included in the study. Annual fluxes of lithogenic matter, CaCO₃, opal, and particulate organic carbon were 3.9, 0.8, 2.6, and 1.5 g m⁻² y⁻¹, respectively, in the shallow trap and 11.3, 0.5, 2.9, and 1.05 g m⁻² y⁻¹, respectively, in the deep trap.Both the shallow and the deep trap showed significant variations in vertical flux over the year. Higher values were found from mid-July to the end of October (total mass flux of 75–130 mg m⁻² d⁻¹ in the shallow trap and 40–225 mg m⁻² d⁻¹ in the deep trap). During all other months, fluxes were fairly low in both traps (most total mass flux values <10 mg m⁻² d⁻¹). The interval of increased fluxes can be separated into (1) a mid-July/August maximum caused by increased primary production as documented in high abundances of marine biomarkers and diatoms and (2) a September/October maximum caused by increased influence of Lena River discharge indicated by maximum lithogenic flux and large amounts of terrigenous/fluvial biomarkers in both traps. During September/October, total mass fluxes in the deep trap were significantly higher than in the shallow trap, suggesting a lateral sediment flux at greater depth. The lithogenic flux data also support the importance of sediment input from the Laptev Sea for the sediment accumulation on the Lomonosov Ridge on geological time scales, as indicated in sedimentary records from this region.     

Acoustic discrimination of two zooplankton species (mysid) at 38 and 120 kHz

Using bifrequency sonar (38 kHz, 120 kHz) directed towards the open sea from the inside of a submarine cave, two species of Mysidacea (Crustacea), similar in shape but not in size, and with different patterns of behaviour, were observed simultaneously and discriminated, and their biomass was estimated during their migration. The first species, Hemimysis speluncola (<1 cm length), lives in the submarine cave, forming a distinct community that migrates horizontally. The second species, Siriella jaltensis (>1 cm length), lives in the open sea and migrates vertically. These species are both detected clearly at 120 kHz, but only the larger one, Siriella jaltensis, is detected at 38 kHz. This distinction allows one to determine the size limits of planktonic objects detected at these frequencies, i.e. 3 mm at 120 kHz and 10 mm at 38 kHz, corresponding to one quarter of the wavelength. The target strength (TS) of each species was calculated from the field data and compared to results calculated from three models. As the volume of the cave occupied by the Hemimysis population is about 300 m³, and the density of the swarm is 36,000 individuals/m³, the number of individuals in the cave is estimated to be around 10 million (or 24 kg). The density of the open-water population of Siriella is estimated to be 13 individuals/m³.