共查询到20条相似文献,搜索用时 46 毫秒
1.
A modelling approach to assessing variations of total suspended solids (tss) mass fluxes during storm events
下载免费PDF全文
![点击此处可从《水文研究》网站下载免费的PDF全文](/ch/ext_images/free.gif)
Connections between the catchment hydrology and accumulation, washoff and transport of pollutants in wet weather greatly affect the management of urban drainage and its wet‐weather effluents. In recent years, the concept of the first flush has gained on prominence and was further developed for analyzing the interaction between the hydrology and transport of runoff pollutants. One of the most important definitions of the first flush can be derived from the analysis of the m(v) curves (i.e. the curves in which the normalized cumulative pollutant mass is plotted vs the normalized cumulative runoff volume). Indeed the m(v) curves, indicating the distribution of pollutant mass versus volume in wet‐weather flow (WWF) discharges, are commonly used for comparing pollutant discharges for different rainfall events and catchments. In this study, the m(v) curves were used to define the concepts of flow‐limited and mass‐limited WWF events. These two different behaviours have been analysed for rainfall/runoff events observed in the urbanized part of the Liguori catchment in Cosenza (Italy). In order to advance the understanding of the intra‐event variability of m(v) curves, the mathematical rainfall/runoff model Storm Water Management Model of the US Environmental Protection Agency (SWMM) was calibrated for eight observed rainfall/runoff events and the differences between observed and simulated m(v) curves were analysed. The results showed a good correlation between the observed and simulated m(v) curves, and this finding offers further benefits in SWMM model calibration. Copyright © 2013 John Wiley & Sons, Ltd. 相似文献
2.
Soil erosion and nutrient losses with surface runoff in the loess plateau in China cause severe soil quality degradation and water pollution. It is driven by both rainfall impact and runoff flow that usually take place simultaneously during a rainfall event. However, the interactive effect of these two processes on soil erosion has received limited attention. The objectives of this study were to better understand the mechanism of soil erosion, solute transport in runoff, and hydraulic characteristics of flow under the simultaneous influence of rainfall and shallow clear‐water flow scouring. Laboratory flume experiments with three rainfall intensities (0, 60, and 120 mm h−1) and four scouring inflow rates (10, 20, 30, and 40 l min−1) were conducted to evaluate their interactive effect on runoff. Results indicate that both rainfall intensity and scouring inflow rate play important roles on runoff formation, soil erosion, and solute transport in the surface runoff. A rainfall splash and water scouring interactive effect on the transport of sediment and solute in runoff were observed at the rainfall intensity of 60 mm h−1 and scouring inflow rates of 20 l min−1. Cumulative sediment mass loss (Ms) was found to be a linear function of cumulative runoff volume (Wr) for each treatment. Solute transport was also affected by both rainfall intensity and scouring inflow rate, and the decrease in bromide concentration in the runoff with time fitted to a power function well. Reynolds number (Re) was a key hydraulic parameter to determine erodability on loess slopes. The Darcy–Weisbach friction coefficients (f) decreased with the Reynolds numbers (Re), and the average soil and water loss rate (Ml) increased with the Reynolds numbers (Re) on loess slope for both scenarios with or without rainfall impact. Copyright © 2010 John Wiley & Sons, Ltd. 相似文献
3.
Vijay P. Singh 《水文研究》2002,16(9):1831-1863
Kinematic wave solutions are derived for transport of a conservative non‐point‐source pollutant during a rainfall‐runoff event over an impervious plane. Rainfall is assumed to be steady, uniform and finite in duration. Prior to the start of rainfall, the pollutant is distributed uniformly over the plane. When rainfall occurs, the pollutant is washed off in a particular manner and the mixing of pollutant in the runoff water occurs either instantaneously or in a finite period of time under the assumption that the pollutant is soluble and is mixed completely in the runoff water. Copyright © 2002 John Wiley & Sons, Ltd. 相似文献
4.
The correct use of the tension disc infiltrometer requires the membrane of the disc base to be completely in contact with the soil surface. To achieve this contact, a thick layer of sand is commonly placed between the soil surface and the disc base. This paper presents an alternative disc (MDB), which, by incorporating a malleable membrane, allows direct infiltration measurements without using a contact sand layer. Infiltration curves obtained with this new design in a soil under three different tillage management treatments were compared with the corresponding curves obtained with a conventional disc (CDB) that uses a contact sand layer. The cumulative infiltration curves measured with CDB were analysed by the differentiated linearization (DL) method, and the corresponding curves obtained with MDB were analysed using both the DL and the cumulative linearization (CL) models. The values of hydraulic conductivity (K0) and sorptivity (S0) estimated with CDB were also compared with those obtained with MDB. Finally, the cumulative infiltration curves measured with CDB and MDB were compared with the corresponding modelled function for the respective K0 and S0 values calculated with the CL and DL models. The results show that, compared with CDB without a contact sand layer, MDB allows complete soil surface wetting even when non‐smoothed soil surfaces are used. The CDB, which yielded average K0 values 18% lower than those estimated with MDB, gave the highest values of standard error for the hydraulic parameters calculated. Furthermore, the subjective method employed in the CDB‐DL technique, which requires the first points of the differential infiltration line corresponding to the sand layer to be manually removed, introduces additional uncertainties in estimating S0 and K0. Comparison between the modelled and measured infiltration curves demonstrates that the DL or CL methods applied to MDB gave excellent estimates of S0 and K0. Copyright © 2012 John Wiley & Sons, Ltd. 相似文献
5.
Analytical and experimental study on dissolved pollutant wash‐off over impervious surfaces
下载免费PDF全文
![点击此处可从《水文研究》网站下载免费的PDF全文](/ch/ext_images/free.gif)
Non‐point source pollution in the impervious surface of city, which including dissolved and particulate pollutants, is a significant source of water pollution. Simple first‐order decay models can generally simulate the cumulative wash‐off process of the particulate pollutants. There is inadequate knowledge as to whether or not they are suitable for dissolved pollutants. This study presents a mathematical wash‐off model for dissolved pollutants, which combines analytical equations for overland flows and the exponential equation for the pollutant wash‐off. A series of laboratory experiments have been conducted to verify this wash‐off model. It shows that the pollutant concentration and pollutant transport rate can be predicted well by the newly developed equations. It is found that the pollutant concentration monotonically decreases to zero as the accumulated pollutants are washed off, whereas the pollutant transport rate first increases to the maximum value and then decreases to zero. The maximum pollutant transport rate is found to increase with the decrease of the arrival time of the maximum value. The difference between the simplified exponential model and the amended wash‐off equation depends on the initial residual percentage (Pc), but the present equation generally provides a more accurate representation of the wash‐off process of dissolved pollutants. 相似文献
6.
The knowledge on particle deposition in streams is mainly based on investigations in mountain streams. No data exist from low‐gradient sand‐bed streams that largely differ in the morphological and hydraulic factors proposed to affect deposition. To identify physical control on particle deposition in low‐gradient streams, we assessed deposition of very fine and ultra fine organic particulate matter in 18 sand‐bed stream reaches. We added particles derived from lake sediment and assessed the mean transport distance SP and the deposition velocity vdep. Additionally, reach hydraulics were estimated by injections of a conservative solute tracer (NaCl). Among the low‐gradient streams, particle deposition kinetics were variable but similar to deposition in mountain streams. SP was solely related to the flow velocity. This relation was confirmed when comprising published data on deposition of fine organic particles. An association between particle deposition and transient storage factors was insignificant. We found significance of the transient storage to SP only for repeated measures within a single reach, when flow velocity and benthic conditions were nearly constant. Measured vdep/vfall ratios were much larger than unity in most reaches. Evidence from this relation suggests that the vertical transport of very fine and ultra fine organic particulate matter through the water column was caused mainly by vertical mixing. Copyright © 2006 John Wiley & Sons, Ltd. 相似文献
7.
Coupled infiltration and filtration behaviours of concrete porous pavement for stormwater management
Cementitious porous pavement (CPP) is a structural low‐impact development material for rainfall–runoff management. Both infiltration and filtration are critical functions for CPP stormwater quality and quantity control. In this study, three groups of CPP specimens exposed to rainfall–runoff for 4 years and experienced with different maintenance intervals (6, 12 and 48 months, respectively) were used to examine CPP infiltration and filtration performance. Particle mass strained on CPP surface, saturated infiltration rate If, temporal infiltration rate I(t), suspended sediment concentration (SSC) and turbidity (τ) were measured to evaluate the process of filtration/infiltration. I(t), SSC and τ were examined less than 50 mg/l of the suspended particle loading. It was found that the CPP surface cleaning methods used in the past 4 years, namely, high pressure wash followed by vacuuming with one atmosphere (100 kPa), were effective, and a 12‐month maintenance interval was verified suitable to maintain the pore structure an acceptable infiltration rate for stormwater management. It was also found that CPP infiltration and filtration process affect each other, and the two properties are coupled in urban stormwater quality and quantity control. On the basis of the experimental measurements, the temporal infiltration rate of the cleaned CPP under a certain particle loading could be simulated by a first‐order nonlinear rational model, and effluent turbidity–SSC relationship was found following a power law. Copyright © 2012 John Wiley & Sons, Ltd. 相似文献
8.
This paper reports on a semi‐analytical/numerical method to model sloshing water in an arbitrarily shaped aqueduct. The water motion is assumed to be inviscid, compressible, and linear (small displacement). The transverse sloshing fluid in an aqueduct is equivalently simplified as a fixed rigid mass M0 and a mass–spring system (M1, K1). According to a rule that the actual fluid (computed with finite element model) and its equivalent mechanical model have the same first sloshing frequency and acting effects on the aqueduct, the analytical solutions of the fixed (impulsive) mass M0, sloshing (convective) massM1, spring stiffness K1, and their locations in the aqueduct body are acquired by the least squares (curve fitting) algorithm. Applying this equivalent principle, the equivalent mechanical models are respectively obtained for the sloshing water in rectangular, semicircular, U‐shaped, and trapezoid aqueducts. The equivalent principle and fluid models are validated through comparison investigations involving rectangular and U‐shaped aqueducts. The dynamic properties and seismic responses of the original and equivalent systems are simulated, compared, and discussed for a U‐shaped aqueduct bridge. The main purpose of this paper is to provide a simplified model of sloshing fluid for the seismic/wind‐resistant computation of the support structures of the aqueduct bridge. Copyright © 2011 John Wiley & Sons, Ltd. 相似文献
9.
Compared to hydrograph recession analysis, which is widely applied in engineering hydrology, the quantitative assessment of stream salinity with time (i.e. the salinograph) has received significantly less attention. In particular, while in many previous hydrological studies an inverse relationship between hydrograph and salinograph responses is apparent, the concept of salinity accession (the inversely related salinity counterpart to hydrograph recession) has not been introduced nor quantitatively evaluated in previous literature. In this study, we conduct a mathematical analysis of salinograph accession, and determine new quantitative relationships between salinity accession and hydrograph recession parameters. An equation is formulated that reproduces the general trend in salinity accession. A salinity accession parameter kc is then introduced and is shown to be the ratio of direct runoff to total stream flow recession parameters: kr/k. The groundwater recession parameter kg was estimated using a simple and rapid method that uses both salinograph and hydrograph data. Salinity accession type‐curves illustrate that under certain conditions, the relative steepness of individual salinographs is dependent upon the ratio of groundwater salinity to direct runoff salinity: Cg/Cr. The salinity accession algorithms are applied to two contrasting field settings: Scott Creek, South Australia and Sandy Creek, northern Queensland, Australia. It was found that kg > k during periods of obvious stream flow recession, for the events analysed. Salinograph accession behaviour was fairly similar for both sites, despite contrasting environments. Using assumed end‐member salinities for groundwater and direct runoff based upon field observations, the behaviour of kc from the Scott Creek site was approximately reproduced by varying the initial groundwater to runoff flow ratio: Qg0/Qr0, within reasonable parameter ranges. The use of salinograph information when used in addition to standard hydrograph analyses provided useful information on recession characteristics of stream components. Copyright © 2008 John Wiley & Sons, Ltd. 相似文献
10.
Jonathan A. Warrick 《水文研究》2015,29(6):936-949
Sediment rating curves, which are fitted relationships between river discharge (Q) and suspended‐sediment concentration (C), are commonly used to assess patterns and trends in river water quality. In many of these studies, it is assumed that rating curves have a power‐law form (i.e. C = aQb, where a and b are fitted parameters). Two fundamental questions about the utility of these techniques are assessed in this paper: (i) how well to the parameters, a and b, characterize trends in the data, and (ii) are trends in rating curves diagnostic of changes to river water or sediment discharge? As noted in previous research, the offset parameter, a, is not an independent variable for most rivers but rather strongly dependent on b and Q. Here, it is shown that a is a poor metric for trends in the vertical offset of a rating curve, and a new parameter, â, as determined by the discharge‐normalized power function [C = â (Q/QGM)b], where QGM is the geometric mean of the Q‐values sampled, provides a better characterization of trends. However, these techniques must be applied carefully, because curvature in the relationship between log(Q) and log(C), which exists for many rivers, can produce false trends in â and b. Also, it is shown that trends in â and b are not uniquely diagnostic of river water or sediment supply conditions. For example, an increase in â can be caused by an increase in sediment supply, a decrease in water supply or a combination of these conditions. Large changes in water and sediment supplies can occur without any change in the parameters, â and b. Thus, trend analyses using sediment rating curves must include additional assessments of the time‐dependent rates and trends of river water, sediment concentrations and sediment discharge. Published 2014. This article is a U.S. Government work and is in the public domain in the USA. Hydrological Processes published by John Wiley & Sons Ltd. 相似文献
11.
V. P. Singh 《水文研究》2002,16(12):2441-2477
Kinematic wave solutions are derived for transport of a conservative non‐point‐source pollutant during a rainfall‐runoff event over an infiltrating plane for two cases: (i) finite‐period mixing and (ii) soil‐mixing zone. Rainfall is assumed to be steady, uniform and finite in duration, and it is assumed to have zero concentration of pollutants. Infiltration is assumed constant in time and space. Prior to the start of rainfall, the pollutant is distributed uniformly over the plane. In the first case, when rainfall occurs, the mixing of pollutant in the runoff water occurs in a finite period of time. In the second case, the chemical concentration is assumed to be a linearly decreasing function of rainfall intensity and overland flow. The solute concentration and discharge are found to depend on the flow characteristics as well as the solute concentration parameters. The characteristics of solute concentration and discharge graphs seem to be similar to those reported in the literature and observed in laboratory experiments. Copyright © 2002 John Wiley & Sons, Ltd. 相似文献
12.
Data from flume studies are used to develop a model for predicting bed‐load transport rates in rough turbulent two‐dimensional open‐channel flows moving well sorted non‐cohesive sediments over plane mobile beds. The object is not to predict transport rates in natural channel flows but rather to provide a standard against which measured bed‐load transport rates influenced by factors such as bed forms, bed armouring, or limited sediment availability may be compared in order to assess the impact of these factors on bed‐load transport rates. The model is based on a revised version of Bagnold's basic energy equation ibsb = ebω, where ib is the immersed bed‐load transport rate, ω is flow power per unit area, eb is the efficiency coefficient, and sb is the stress coefficient defined as the ratio of the tangential bed shear stress caused by grain collisions and fluid drag to the immersed weight of the bed load. Expressions are developed for sb and eb in terms of G, a normalized measure of sediment transport stage, and these expressions are substituted into the revised energy equation to obtain the bed‐load transport equation ib = ω G 3·4. This equation applies regardless of the mode of bed‐load transport (i.e. saltation or sheet flow) and reduces to ib = ω where G approaches 1 in the sheet‐flow regime. That ib = ω does not mean that all the available power is dissipated in transporting the bed load. Rather, it reflects the fact that ib is a transport rate that must be multiplied by sb to become a work rate before it can be compared with ω. It follows that the proportion of ω that is dissipated in the transport of bed load is ibsb/ω, which is approximately 0·6 when ib = ω. It is suggested that this remarkably high transport efficiency is achieved in sheet flow (1) because the ratio of grain‐to‐grain to grain‐to‐bed collisions increases with bed shear stress, and (2) because on average much more momentum is lost in a grain‐to‐bed collision than in a grain‐to‐grain one. Copyright © 2006 John Wiley & Sons, Ltd. 相似文献
13.
The application of electrical conductivity as a tracer for hydrograph separation in urban catchments
Brian A. Pellerin Wilfred M. Wollheim Xiahong Feng Charles J. Vörösmarty 《水文研究》2008,22(12):1810-1818
Two‐component hydrograph separation was performed on 19 low‐to‐moderate intensity rainfall events in a 4·1‐km2 urban watershed to infer the relative and absolute contribution of surface runoff (e.g. new water) to stormflow generation between 2001 and 2003. The electrical conductivity (EC) of water was used as a continuous and inexpensive tracer, with order of magnitude differences in precipitation (12–46 µS/cm) and pre‐event streamwater EC values (520–1297 µS/cm). While new water accounted for most of the increased discharge during storms (61–117%), the contribution of new water to total discharge during events was typically lower (18–78%) and negatively correlated with antecedent stream discharge (r2 = 0·55, p < 0·01). The amount of new water was positively correlated with total rainfall (r2 = 0·77), but hydrograph separation results suggest that less than half (9–46%) of the total rainfall on impervious surfaces is rapidly routed to the stream channel as new water. Comparison of hydrograph separation results using non‐conservative tracers (EC and Si) and a conservative isotopic tracer (δD) for two events showed similar results and highlighted the potential application of EC as an inexpensive, high frequency tracer for hydrograph separation studies in urban catchments. The use of a simple tracer‐based approach may help hydrologists and watershed managers to better understand impervious surface runoff, stormflow generation and non‐point‐source pollutant loading to urban streams. Copyright © 2007 John Wiley & Sons, Ltd. 相似文献
14.
In situ and high frequency monitoring of suspended sediment properties using a spectrophotometric sensor
下载免费PDF全文
![点击此处可从《水文研究》网站下载免费的PDF全文](/ch/ext_images/free.gif)
Núria Martínez‐Carreras Michael P. Schwab Julian Klaus Christophe Hissler 《水文研究》2016,30(19):3533-3540
It is well known that sediment properties, including sediment‐associated chemical constituents and sediment physical properties, can exhibit significant variations within and between storm runoff events. However, the number of samples included in suspended sediment studies is often limited by time‐consuming and expensive laboratory procedures after stream water sampling. This restricts high frequency sampling campaigns to a limited number of events and reduces accuracy when aiming to estimate fluxes and loads of sediment‐associated chemical constituents. In this study, we address the potential of a portable ultraviolet–visible spectrophotometer (220–730 nm) to estimate suspended sediment properties in a resource efficient way. Several field deployable spectrophotometers are currently available for in‐stream measurements of environmental variables at high temporal resolution. These instruments have primarily been developed and used to quantify solute concentrations (e.g. dissolved organic carbon and NO3‐N), total concentrations of dissolved and particulate forms (e.g. total organic carbon) and turbidity. Here we argue that light absorbance values can be calibrated to estimate sediment properties. We present light absorbance data collected at 15‐min intervals in the Weierbach catchment (NW Luxembourg, 0.45 km2) from December 2013 to January 2015. In this proof‐of‐concept study, we performed a local calibration using suspended sediment loss‐on‐ignition (LOI) measurements as an example of suspended sediment property. We assessed the performance of several regression models that relate light absorbance measurements with the percentage weight LOI. The MM‐robust regression method presented the lowest standard error of prediction (0.48%) and was selected for calibration (adjusted r2 = 0.76 between observed and predicted values). The model was then used to predict LOI during a storm runoff event in December 2014. This study demonstrates that spectrophotometers can be used to estimate suspended sediment properties at high temporal resolution and for long‐time spans in a simple, non‐destructive and affordable manner. Copyright © 2016 John Wiley & Sons, Ltd. 相似文献
15.
Akansha Patel Ajanta Goswami Jaydeo K. Dharpure Meloth Thamban Parmanand Sharma Anil V. Kulkarni Sunil Oulkar 《水文研究》2021,35(2):e14058
The ongoing glacier shrinking in the Himalayan region causes a significant threat to freshwater sustainability and associated future runoff. However, data on the spatial climatic contribution of glacier retreat is scanty in this region. To investigate the spatially distributed glacier surface energy and mass fluxes, a two-dimensional mass balance model was developed and applied to the selected glaciers of the Chandra basin, in the Upper Indus Basin, Western Himalaya. This model is driven by the remote sensing data and meteorological variables measured in the vicinity of the Chandra basin for six hydrological years (October 2013 to September 2019). The modelled variables were calibrated/validated with the in-situ observation from the Himansh station in the Chandra basin. We have derived air temperature (Ta ) spatially using the multivariate statistical approach, which indicates a relative error of 0.02–0.05°C with the observed data. Additionally, the relative error between the modelled and observed radiation fluxes was <10.0 W m−2. Our study revealed that the Chandra basin glaciers have been losing its mass with a mean annual mass balance of −0.59 ± 0.12 m w.e. a−1 for the six hydrological years. Results illustrated that the mean surface melt rate of the selected glaciers ranged from −5.1 to −2.5 m w.e. a−1 that lies between 4500 and 5000 m a.s.l. The study revealed that the net radiation (RN) contributes ~75% in total energy (FM ) during the melt season while sensible heat (HS) , latent heat (Hl) , and ground heat (HG) fluxes shared 15%, 8%, and 2%, respectively. Sensitivity analysis of the energy balance components suggested that the mass balance is highly sensitive to albedo and surface radiations in the study area. Overall, the proposed model performed well for glacier-wide energy and mass balance estimation and confirms the utility of remote sensing data, which may help in reducing data scarcity in the upper reaches of the Himalayan region. 相似文献
16.
An approach to analysing plot scale infiltration and runoff responses to rainfall of fluctuating intensity 总被引:1,自引:0,他引:1
下载免费PDF全文
![点击此处可从《水文研究》网站下载免费的PDF全文](/ch/ext_images/free.gif)
David Dunkerley 《水文研究》2017,31(1):191-206
Simulated rainfall of fluctuating intensity was applied to runoff plots on bare dryland soils in order to explore a new method for analysing the non‐steady‐state responses of infiltration and overland flow. The rainfall events all averaged 10 mm/h but included intensity bursts of up to 70 mm/h and lasting 5–15 min, as well as periods of low intensity and intermittency of up to 25 min. Results were compared with traditional steady‐state estimates of infiltrability made under simulated rainfall sustained at a fixed intensity of 10 mm/h. Mean event infiltration rate averaged 13.6% higher under fluctuating intensities, while runoff ratios averaged only 63% of those seen under constant intensity. In order to understand the changing soil infiltrability, up to three affine Horton infiltration equations were fitted to segments of each experiment. All equations had the same final infiltrability fc, but adjusted values for coefficients f0 (initial infiltrability) and Kf (exponential decay constant) were fitted for periods of rainfall that followed significant hiatuses in rainfall, during which subsurface redistribution allowed near‐surface soil suction to recover. According to the fitted Horton equations, soil infiltrability recovered by up 10–24 mm/h during intra‐event rainfall hiatuses of 15 to 20‐min duration, contributing to higher overall event infiltration rates and to reduced runoff ratios. The recovery of infiltrability also reduced the size of runoff peaks following periods of low intensity rainfall, compared with the predictions based on single Horton infiltration equations, and in some cases, no runoff at all was recorded from late intensity peaks. The principal finding of this study is that, using a set of affine equations, the intra‐event time variation of soil infiltrability can be tracked through multiple intensity bursts and hiatuses, despite the lack of steady‐state conditions. Copyright © 2016 John Wiley & Sons, Ltd. 相似文献
17.
We assess the relative merits of application of the most commonly used field methods (soil‐water balance (SWB), chloride mass balance (CMB) and soil moisture monitoring (NP)) to determine recharge rates in micro‐irrigated and non‐irrigated areas of a semi‐arid coastal orchard located in a relatively complex geological environment. Application of the CMB method to estimate recharge rates was difficult owing to the unusually high, variable soil‐water chloride concentrations. In addition, contrary to that expected, the chloride concentration distribution at depths below the root zone in the non‐irrigated soil profiles was greater than that in the irrigated profiles. The CMB method severely underestimated recharge rates in the non‐irrigated areas when compared with the other methods, although the CMB method estimated recharge rates for the irrigated areas, that were similar to those from the other methods, ranging from 42 to 141 mm/year. The SWB method, constructed for a 15‐year period, provided insight into the recharge process being driven by winter rains rather than summer irrigation and indicated an average rate of 75 mm/year and 164 mm/year for the 1984 – 98 and 1996 – 98 periods, respectively. Assuming similar soil‐water holding capacity, these recharge rates applied to both irrigated and non‐irrigated areas. Use of the long period of record was important because it encompassed both drought and heavy rainfall years. Successful application of the SWB method, however, required considerable additional field measurements of orchard ETc, soil‐water holding capacity and estimation of rainfall interception – runoff losses. Continuous soil moisture monitoring (NP) was necessary to identify both daily and seasonal seepage processes to corroborate the other recharge estimates. Measured recharge rates during the 1996 – 1998 period in both the orchards and non‐irrigated site averaged 180 mm/year. The pattern of soil profile drying during the summer irrigation season, followed by progressive wetting during the winter rainy season was observed in both irrigated and non‐irrigated soil profiles, confirming that groundwater recharge was rainfall driven and that micro‐irrigation did not ‘predispose’ the soil profile to excess rainfall recharge. The ability to make this recharge assessment, however, depended on making multiple field measurements associated with all three methods, suggesting that any one should not be used alone. Copyright © 2000 John Wiley & Sons, Ltd. 相似文献
18.
René E. Van der Sant Petter Nyman Philip J. Noske Christoph Langhans Patrick N.J. Lane Gary J. Sheridan 《地球表面变化过程与地形》2018,43(10):2033-2044
Post‐wildfire runoff and erosion are major concerns in fire‐prone landscapes around the world, but these hydro‐geomorphic responses have been found to be highly variable and difficult to predict. Some variations have been observed to be associated with landscape aridity, which in turn can influence soil hydraulic properties. However, to date there has been no attempt to systematically evaluate the apparent relations between aridity and post‐wildfire runoff. In this study, five sites in a wildfire burnt area were instrumented with rainfall‐runoff plots across an aridity index (AI) gradient. Surface runoff and effective rainfall were measured over 10 months to allow investigation of short‐ (peak runoff) and longer‐term (runoff ratio) runoff characteristics over the recovery period. The results show a systematic and strong relation between aridity and post‐wildfire runoff. The average runoff ratio at the driest AI site (33.6%) was two orders of magnitude higher than at the wettest AI site (0.3%). Peak runoff also increased with AI, with up to a thousand‐fold difference observed during one event between the driest and wettest sites. The relation between AI, peak 15‐min runoff (Q15) and peak 15‐min rainfall intensity (I15) (both in mm h‐1) could be quantified by the equation: Q15 = 0.1086I15 × AI 2.691 (0.65<AI<1.80, 0<I15<45) (adjusted r2 = 0.84). The runoff ratios remained higher at drier AI sites (AI 1.24 and 1.80) throughout the monitoring period, suggesting higher AI also lengthens the window of disturbance after wildfire. The strong quantifiable link which this study has determined between AI and post‐wildfire surface runoff could greatly improve our capacity to predict the magnitude and location of hydro‐geomorphic processes such as flash floods and debris flows following wildfire, and may help explain aridity‐related patterns of soil properties in complex upland landscapes. Copyright © 2018 John Wiley & Sons, Ltd. 相似文献
19.
Following the statistical analyses of long‐term rainfall‐runoff records from research basins in humid temperate latitudes, Hewlett and co‐workers extended the global challenge to disprove their findings that rainfall intensity was non‐significant. This paper responds to Hewlett's challenge as no preceding analyses have involved forested basins in a tropical cyclone‐prone area. Based on a 7 year rainfall‐runoff record, quickflow (QF), peak flow (QP) and quickflow response ratios (QRR) were regressed as dependent variables against rainfall parameters (intensity, Pi, amount, P), storm duration, D and antecedent flow, I. These data sets were categorised into total streamflow (Q) classes and stratified into three seasons, (monsoon, post‐monsoon and dry) for forested and cleared catchments. Where rainfall variable collinearity met acceptable levels, the addition of Pi to regression models including P, D, I contributed up to 9% and 66% of the respective variations in quickflow and peak flow. For the highest Q storm classes (monsoon), Pi alone accounted for up to 67% and 91% of the variation in QF and QP respectively and was the dominant influence on QP for all seasons. The very high rainfall intensities experienced in the monsoon season is a causal factor why these results differ from those of other research drainage basins. Surprisingly, Pi continued to have a significant influence on QF for dry season classes when less‐intense rainfall occurs. Further the results were similar for both catchments across all seasons. P was the dominant independent variable affecting QF above a threshold Q of 50 mm (monsoon), as rainfall contributes directly to saturation overland flow and return flow under saturated conditions. Further although QRR increased with increasing Q for each season, the regression results for that parameter were poor possibly due to the non‐linearity of the rainfall‐runoff relationship. Copyright © 2010 John Wiley & Sons, Ltd. 相似文献
20.
John C. Panuska Laura Ward Good Peter A. Vadas Dennis L. Busch Asli Ozkaynak 《水文研究》2011,25(15):2329-2338
Phosphorus (P) export from agricultural lands above known threshold levels can result in adverse impacts to receiving water quality. Phosphorus loss occurs in dissolved and sediment‐bound, or particulate phosphorous (PP), forms, with the latter often dominating losses from row‐cropped systems. To target practices, land managers need good computer models and model developers need good monitoring data. Sediment monitoring data (e.g. radiometric finger printing and sediment P sorption capacity) can help identify sediment source areas and improve models, but require more sediment mass than is typically obtained by automatic sampling. This study compares a simple suspended sediment sampler developed at the University of Exeter (UE) with automatic sampling in intermittent channels draining corn and alfalfa fields. The corn field had a greater runoff coefficient (27%) than alfalfa (11%). No differences were found in enrichment ratios (sediment constituent/soil constituent) in PP (PPER) or percent loss on ignition (LOIER) between paired UE samplers on corn. The median LOIER for the UE samplers (1·9%) did not differ significantly (p > 0·13) from the automatic sampler (2·0%). The PPER from the UE samplers was on average 20% lower than the automatic samplers. A correlation (r2 = 0·75) was found between sediment PP and % LOI from automatic samplers and UE samplers for particles < 50 µm, while for > 50 µm PP concentration did not change with changes in % LOI. Sediment ammonium‐oxalate extractable metals were similarly related to LOI, with the strongest correlation for iron (r2 = 0·71) and magnesium (r2 = 0·70). Copyright © 2011 John Wiley & Sons, Ltd. 相似文献