Predictive instantaneous optimal control of elastic structures during earthquakes

A predictive instantaneous optimal control (PIOC) algorithm is proposed for controlling the seismic responses of elastic structures. This algorithm compensates for the time delay that happens in practical control applications by predicting the structural response over a period that equals the time delay, and by substituting the predicted response in the instantaneous optimal control (IOC) algorithm. The unique feature of this proposed PIOC algorithm is that it is simple and at the same time compensates for the time delay very effectively. Numerical examples of single degree of freedom structures are presented to compare the performance of PIOC and IOC systems for various time delay magnitudes. Results show that a time delay always causes degradation of control efficiency, but PIOC can greatly reduce this degradation compared to IOC. The effects of the structure's natural periods and the choice of control gains on the degradation induced by the time delay are also analyzed. Results show that shorter natural periods and larger control gains are both more sensitive and more serious to the degradation of control efficiency. Finally, a practical application of PIOC is performed on a six‐story moment‐resisting steel frame. It is demonstrated that PIOC contributes significantly to maintain stability in multiple degree of freedom structures, and at the same time PIOC has a satisfactory control performance. Copyright © 2003 John Wiley & Sons, Ltd.     

结构瞬时最优控制参数影响的数值分析

在瞬时最优控制算法理论分析的基础上，分别以单自由度和三自由度结构模型为例，研究了时间间隔和权矩阵对结构控制反应的影响。首先，进行了瞬时最优控制算法的理论分析，提出了控制算法的影响参数；其次，分别对单自由度和三自由度结构在无控、LQR和瞬时最优三种方法控制下，分析了时间间隔和权矩阵对结构反应的影响。结果表明：时间间隔和权矩阵对结构瞬时最优控制效果影响很大。     

Design of passive systems for control of inelastic structures

A design strategy for control of buildings experiencing inelastic deformations during seismic response is formulated. The strategy is using weakened, and/or softened, elements in a structural system while adding passive energy dissipation devices (e.g. viscous fluid devices, etc.) in order to control simultaneously accelerations and deformations response during seismic events. A design methodology is developed to determine the locations and the magnitude of weakening and/or softening of structural elements and the added damping while insuring structural stability. A two‐stage design procedure is suggested: (i) first using a nonlinear active control algorithm, to determine the new structural parameters while insuring stability, then (ii) determine the properties of equivalent structural parameters of passive system, which can be implemented by removing or weakening some structural elements, or connections, and by addition of energy dissipation systems. Passive dampers and weakened elements are designed using an optimization algorithm to obtain a response as close as possible to an actively controlled system. A case study of a five‐story building subjected to El Centro ground motion, as well as to an ensemble of simulated ground motions, is presented to illustrate the procedure. The results show that following the design strategy, a control of both peak inter‐story drifts and total accelerations can be obtained. Copyright © 2008 John Wiley & Sons, Ltd.     

Predictive optimal control for seismic analysis of non-linear and hysteretic structures

In this paper, an effective active predictive control algorithm is developed for the vibration control of non-linear hysteretic structural systems subjected to earthquake excitation. The non-linear characteristics of the structural behaviour and the effects of time delay in both the measurements and control action are included throughout the entire analysis (design and validation). This is very important since, in current design practice, structures are assumed to behave non-linearly, and time delays induced by sensors and actuator devices are not avoidable. The proposed algorithm focuses on the instantaneous optimal control approach for the development of a control methodology where the non-linearities are brought into the analysis through a non-linear state vector and a non-linear open-loop term. An autoregressive (AR) model is used to predict the earthquake excitation to be considered in the prediction of the structural response. A performance index that is quadratic in the control force and in the predicted non-linear states, with two additional energy related terms, and that is subjected to a non-linear constraint equation, is minimized at every time step. The effectiveness of the proposed closed-open loop non-linear instantaneous optimal prediction control (CONIOPC) strategy is presented by the results of numerical simulations. Since non-linearity and time-delay effects are incorporated in the mathematical model throughout the derivation of the control methodology, good performance and stability of the controlled structural system are guaranteed. Copyright © 1999 John Wiley & Sons, Ltd.     

Design of controlled elastic and inelastic structures

One of the founders of structural control theory and its application in civil engineering,Professor Emeritus Tsu T.Soong,envisioned the development of the integral design of structures protected by active control devices.Most of his disciples and colleagues continuously attempted to develop procedures to achieve such integral control.In his recent papers published jointly with some of the authors of this paper,Professor Soong developed design procedures for the entire structure using a design-redesign proce...     

Predictive active control of MDOF structures

This paper presents a theoretical study of a predictive active control system used to improve the response of multi‐degree‐of‐freedom (MDOF) structures to earthquakes. As an example a building frame equipped with electrorheological (ER) dampers is considered. The aim of the design is to find a combination of forces that are produced by the ER dampers in order to obtain an optimal structural response. The mechanical response of ER fluid dampers is regulated by an electric field. Linear auto‐regressive model with exogenous input (ARX) is used to predict the displacements and the velocities of the frame in order to overcome the time‐delay problem in the control system. The control forces in the ER devices are calculated at every time step by the optimal control theory (OCT) according to the values of the displacements and of the velocities that are predicted at the next time step at each storey of the structure. A numerical analysis of a seven‐storey ER damped structure is presented as an example. It shows a significant improvement of the structural response when the predictive active control system is applied compared to that of an uncontrolled structure or that of a structure with controlled damping forces with time delay. The structure's displacements and velocities that were used to obtain the optimal control forces were predicted according to an ‘occurring’ earthquake by the ARX model (predictive control). The response was similar to that of the structure with control forces that were calculated from a ‘known’ complete history of the earthquake's displacement and velocity values, and were applied without delay (instantaneous control). Copyright © 2000 John Wiley & Sons, Ltd.     

Active interaction control of civil structures. Part 1: SDOF systems

This paper presents a family of semi‐active control algorithms termed as active interaction control (AIC) used for seismic response control of civil structures. AIC control algorithms include active interface damping (AID), optimal connection strategy (OCS) and tuned interaction damping (TID). A typical SDOF AIC system consists of a primary structure, an auxiliary structure and an interaction element. The auxiliary structure typically has stiffness comparable to that of the primary structure while its natural frequency is much higher than that of the primary structure. Interactions between the primary and the auxiliary structures are defined by specific AIC control logic such that vibrational energy is extracted from the primary structure into the auxiliary structure during a locking phase and dissipated in the auxiliary structure in the subsequent unlocking phase. The stability of AIC control algorithms is shown using the Lyapunov direct method. The efficacy of AIC control algorithms is demonstrated by the results of numerical simulations of SDOF systems subjected to seismic ground motions. Practical issues such as sampling period and time delay are also investigated in this study. Copyright © 2001 John Wiley & Sons, Ltd.     

Adaptive bang–bang control for the vibration control of structures under earthquakes

An adaptive method based on the modified bang–bang control algorithm is proposed for the vibration control of structures subjected to unexpected severe seismic loads greater than the design loads. A hydraulic‐type active mass damper was made and experiments were carried out in the laboratory using a one‐story test structure and a five‐story test structure with the active mass damper. Through numerical simulations and experiments it was confirmed that the proposed method works well to suppress the vibration of structures subjected to unexpected severe seismic loads greater than the design loads without causing any unstable situations. Copyright © 2003 John Wiley & Sons, Ltd.     

Trust-region based instantaneous optimal semi-active control of long-span spatially extended structures with MRF-04K damper

In the field of civil engineering, magnetorheological fluid （MRF） damper-based semi-active control systems have received considerable attention for use in protecting structures from natural hazards such as strong earthquakes and high winds. In this paper, the MRF damper-based semi-active control system is applied to a long-span spatially extended structure and its feasibility is discussed. Meanwhile, a _trust-region method based instantaneous optimal semi-active control algorithm （TIOC） is proposed to improve the performance of the semi-active control system in a multiple damper situation. The proposed TIOC describes the control process as a bounded constraint optimization problem, in which an optimal semi- active control force vector is solved by the trust-region method in every control step to minimize the structural responses. A numerical example of a railway station roof structure installed with MRF-04K dampers is presented. First, a modified Bouc- Wen model is utilized to describe the behavior of the selected MRF-04K damper. Then, two semi-active control systems, including the well-known clipped-optimal controller and the proposed TIOC controller, are considered. Based on the characteristics of the long-span spatially extended structure, the performance of the control system is evaluated under uniform earthquake excitation and travelling-wave excitation with different apparent velocities. The simulation results indicate that the MR fluid damper-based semi-active control systems have the potential to mitigate the responses of full-scale long-span spatially extended structures under earthquake hazards. The superiority of the proposed TIOC controller is demonstrated by comparing its control effectiveness with the clipped-optimal controller for several different cases.     

Simplified inelastic seismic analysis of base‐isolated structures using the N2 method

In the paper a simplified nonlinear method has been applied to the analysis of base‐isolated structures. In the first part, a three‐linear idealization of the capacity curve is proposed. The initial stiffness is defined based on the first yielding point in the superstructure, whereas the secondary slope depends on the failure mechanism of the superstructure. A consequence is a much more pronounced secondary slope, which does not correspond to the presumptions used in the originally proposed N2 method. A parametric nonlinear dynamic study of single degree of freedom systems with different hardening slopes and damping has been performed for an ensemble of seven EC8 spectrum‐compatible artificial accelerograms. It was concluded that, in the long‐period range, the equal displacement rule could be assumed also for the proposed systems with non‐zero post‐yield stiffness. In the second part, the proposed idealization was used for the analysis of isolated RC frame buildings that were isolated with different (lead) rubber‐bearing isolation systems. The stiffness of the isolators was selected for three different protection levels and for three different ground motion intensities, which have resulted in elastic as well as moderately and fully damaged superstructure performance levels. Three different lateral load distributions were investigated. It was observed that a triangular distribution, with an additional force at the base, works best in the majority of practical cases. It was concluded that the N2 method can, in general, provide a reasonably accurate prediction of the actual top displacement, as well as of the expected damage to the superstructure. Copyright © 2009 John Wiley & Sons, Ltd.     

Estimation of inelastic displacement ratio for base‐isolated structures

This study develops a straightforward approximate method to estimate inelastic displacement ratio, C₁ for base‐isolated structures subjected to near‐fault and far‐fault ground motions. Taking into account the inelastic behavior of isolator and superstructure, a 2 degrees of freedom model is employed. A total of 90 earthquake ground motions are selected and classified into different clusters according to the frequency content features of records represented by the peak ground acceleration to peak ground velocity ratio, A_p/V_p. A parametric study is conducted, and effective factors in C₁ (i.e., fundamental vibration period of the superstructure, T_s; postyield stiffness ratio of the superstructure, α_s; strength reduction ratio, R; vibration period of the isolator, T_b; strength of the isolator, Q; ratio of superstructure mass to total mass of the system, γ_m) are recognized. The results indicate that the practical range of C₁ values could be expected for base‐isolated structures. Subsequently, effective parameters are included in simple predictive equations. Finally, the accuracy of the proposed approximate equations is evaluated and verified through error measurement, and comparisons are made in the analyses.     

AP/VP specific inelastic displacement ratio for seismic response estimation of structures

In this study, two new site specific statistical equations are proposed to estimate the inelastic displacement ratio, C₁ of structures subjected to far fault (FF) and near fault (NF) ground motions. The proposed equations consider the effects of fundamental vibration period of the structure, T, lateral strength ratio, R and frequency content of the design earthquake record represented by the A_p/V_p ratio (or T₀ = 2π/A_p/V_p), which is a function of the earthquake magnitude, distance to fault, faulting mechanism and site class. It was observed that the C₁ values obtained from the proposed equations are in good agreement with the calculated results. The flare of the plotted C₁ vs. T/T₀ curves enables the proposed equations to cover nearly all the calculated C₁ data range and give satisfactory results. However, the curves obtained using the C₁ equations of several codes and those available in the literature do not cover the whole calculated C₁ data range and generally give unconservative results (smaller C₁ values) especially in the shorter period range. For the longer period range, the predictions of C₁ obtained from the proposed equation and the ones available in the literature are in good agreement with the calculated C₁ data. Copyright © 2014 John Wiley & Sons, Ltd.     

Dynamics of inelastic base‐isolated structures subjected to analytical pulse ground motions

Structural design code provisions worldwide prescribe relatively small seismic force reduction factors for seismically base‐isolated structures, making their response to design‐level earthquake excitation essentially elastic. This paper uses the method of dimensional analysis to prove that; in most cases, this is not a conservative design approach but a necessity that emerges from the dynamics of base‐isolated structures. It is shown that allowing typical base‐isolated structures to yield results in large displacement ductility demands for the structure. This phenomenon is caused by the change in the nature of the ground motion excitation as it is transmitted to the structure through the seismic base isolation system as well as by the change in the distribution of displacements between the structure and the isolation bearings caused by yielding of the isolated structure. Copyright © 2013 John Wiley & Sons, Ltd.     

结构主动控制系统时间滞后测量与补偿方法

本文研究了结构主动控制系统时间滞后产生的原因,利用作者建立的结构主动控制系统进行了系统时间滞后测量方法的研究,测量得到了该系统时间滞后的具体数值,在此基础上,研究了时间滞后对控制系统的影响,提出了结构主动控制系统时间滞后的三种补偿,即移相法,泰勒级数展开法和预估状态向量法,通过主动控制试验证了时间滞后补偿方法的有效性。     

Semi‐active multi‐step predictive control of structures using MR dampers

A semi‐active multi‐step predictive control (SAMPC) system with magnetorheological (MR) dampers is developed to reduce the seismic responses of structures. This system can predict the next multi‐step responses of structure according to the current state and has a function of self‐compensation for time delay that occurred in real application. To study the performance of the proposed control algorithm for addressing time delay and reducing the seismic responses, a numerical example of an 11‐story structure with MR dampers is presented. Comparison with the uncontrolled structure indicates that both the peak and the norm values of structural responses are all clearly reduced when the predictive length l?10 and the delayed time step d?20 are selected, and the SAMPC strategy can guarantee the stability of the controlled structure and reduce the effects of time delay on controlled responses to a certain extent. A performance comparison is also made between the SAMPC strategy and the passive‐off and passive‐on methods; results indicate that this SAMPC system is more effective than the two passive methods in reducing structural responses subjected to earthquakes. Copyright © 2008 John Wiley & Sons, Ltd.     

地震动瞬时能量谱与结构位移响应关系研究

本文通过HHT变换得到瞬时能量谱,并以HHT对地震动作用下的结构位移响应进行分析,发现长周期结构动力响应的显著特点:最大结构位移响应总是滞后于地震动激励的最大能量谱值时间.滞后的时间主要取决于结构的动力特性参数(特别是自振周期),也与地震动的类型有关.仿真计算的结果表明:长周期结构的破环与倒塌并不发生在地震动强度最大的时刻,而多数是在地震动末期,甚至在地震动完全消失之后.有益的结论为结构控制设计与安全提供科学依据.     

Predictive control of seismic structures with semi‐active friction dampers

In this paper a predictive control method especially suitable for the control of semi‐active friction dampers is proposed. By keeping the adjustable slip force of a semi‐active friction damper slightly lower than the critical friction force, the method allows the damper to remain in its slip state throughout an earthquake of arbitrary intensity, so the energy dissipation capacity of the damper can be improved. The proposed method is formulated in a discrete‐time domain and cast in the form of direct output feedback for easy control implementation. The control algorithm is able to produce a continuous and smooth slip force for a friction damper and thus avoid exerting the high‐frequency structural response that usually exists in structures with conventional friction dampers. Using a numerical study, the control performance of a multiple degrees of freedom (DOF) structural system equipped with passive friction dampers and semi‐active dampers controlled by the proposed method are compared. The numerical case shows that by merely using a single semi‐active friction damper and a few sensors, the proposed method is able to achieve better acceleration reduction than the case using multiple passive dampers. Copyright © 2004 John Wiley & Sons, Ltd.     

地震下结构振动的最优控制算法模型比较与改进

模拟地震激励输入结构的过程,将控制目标函数化解到每个时间步长上。用激励所产生的脉冲响应重新构造控制目标函数,直接从泛函变分出发,推导出了一种改进的最优控制算法,并用状态转移的数值方法加以实现。从概念上讲,本算法是一种更为合理的结构最优控制算法。算例表明,在相同控制能量下,本算法能更有效地削减响应峰值,且稳定性良好。     

Discrete‐time variable structure control of seismically excited building structures

Generally, the active structural control system belongs to the discrete‐time control system, and the sampling period is one of the most important factors that would directly affect the performance of the control system. In this paper, active control approaches by using the discrete‐time variable structure control theory are studied for reducing the dynamic responses of seismically excited building structures. Based on the discrete reaching law method, a feedback controller which includes the sampling period is presented. The controller is extended by introducing the saturated control method to avoid the adverse effect when the actuators are saturated due to unexpected extreme earthquakes. The simulation results are obtained for a single‐degree‐of‐freedom (SDOF) system and a MDOF shear building equipped with active brace system (ABS) under seismic excitations. It is found that the discrete variable structure control approach and its saturated control method presented in this paper are quite effective. Copyright © 2001 John Wiley & Sons, Ltd.