Can channel banks be the dominant source of fine sediment in a UK river?: an example using 137Cs to interpret sediment yield and sediment source

Cultivated fields have been shown to be the dominant sources of sediment in almost all investigated UK catchments, typically contributing 85 to 95% of sediment inputs. As a result, most catchment management strategies are directed towards mitigating these sediment inputs. However, in many regions of the UK such as the Nene basin there is a paucity of sediment provenance data. This study used the caesium‐137 (¹³⁷Cs) inventories of lake and floodplain cores as well as the ¹³⁷Cs activities of present day sediment to determine sediment provenance. Sediment yields were also reconstructed in a small lake catchment. Low ¹³⁷Cs inventories were present in the lake and floodplain cores in comparison to the reference inventory and inventories in cores from other UK catchments. Caesium‐137 activities in the present day sediments were low; falling close to those found in the channel bank catchment samples. It was estimated that 60 to 100% of the sediment in the Nene originated from channel banks. Pre‐1963 sediment yields were approximately 11.2 t km^?2 yr^?1 and post‐1963 was approximately 11.9 t km^?2 yr^?1. The lack of increased sediment yield post‐1963 and low sediment yield is unusual for a UK catchment (where a yield of 28 to 51 t km^?2 yr^?1 is typical for a lowland agricultural catchment), but is explained by the low predicted contribution of sediment from agricultural topsoils. The high channel bank contribution is likely caused by the river being starved of sediment from topsoils, increasing its capacity to entrain bank material. The good agreement between the results derived using cores and recently transported sediments, highlight the reliability of ¹³⁷Cs when tracing sediment sources. However, care should be taken to assess the potential impacts of sediment particle size, sediment focusing in lakes and the possible remobilization of ¹³⁷Cs from sedimentary deposits. Copyright © 2016 John Wiley & Sons, Ltd.     

Sediment yields and sources in a welsh upland lake-catchment during the past 800 years

Estimates of suspended sediment yield over the past 800 years have been derived from a whole-basin study of lake sediments in Llyn Geirionydd, North Wales. Magnetic and physical sediment properties were used to correlate a suite of cores to a master chronology based on ²¹⁰Pb and ¹⁴C dates. The sources of sediment within the catchment were identified by comparing the magnetic and heavy metal properties of sediments, soils, and stream sediments. Mean suspended sediment yields range from 6 to 18 t km^?2 yr^?1 with high yields in the periods 1765-1830 and 1903-1985 corresponding to mining activities in the catchment. The impact of earlier deforestation, agricultural expansion, or climatic change on sediment yields is low, although there is evidence that agricultural activities increased levels of peak stream discharge. Afforestation in the 20th century does not appear to have significantly increased sediment yield. Sediment sources have remained fairly constant through time; they appear to be widespread and dominated by stream channel sides rather than point sources, except during the mining phases when spoil material has dominated the sediment load. Sediment loads to the lake today are still dominated by sediment derived from unvegetated spoil heaps.     

Short‐term spatial and temporal patterns of suspended sediment transfer in proglacial channels,small River Glacier,Canada

Alpine glacial basins are a significant source and storage area for sediment exposed by glacial retreat. Recent research has indicated that short‐term storage and release of sediment in proglacial channels may control the pattern of suspended sediment transfer from these basins. Custom‐built continuously recording turbidimeters installed on a network of nine gauging sites were used to characterize spatial and temporal variability in suspended sediment transfer patterns for the entire proglacial area at Small River Glacier, British Columbia, Canada. Discharge and suspended sediment concentration were measured at 5 min intervals over the ablation season of 2000. Differences in suspended sediment transfer patterns were then extracted using multivariate statistics (principal component and cluster analysis). Results showed that each gauging station was dominated c. 80% of days by diurnal sediment transfer patterns and ‘low’ suspended sediment concentrations. ‘Irregular’ transfer patterns were generally associated with ‘high’ sediment concentrations during snowmelt and rainfall events, resulting in the transfer of up to 70% of the total seasonal suspended sediment load at some gauging stations. Suspended sediment enrichment of up to 600% from channel storage release and extrachannel inputs occurred between the glacial front and distal proglacial boundary. However, these patterns differed significantly between gauging stations as determined by the location of the gauging station within the catchment and meteorological conditions. Overall, the proglacial area was the source for up to 80% of the total suspended sediment yield transferred from the Small River Glacier basin. These results confirmed that sediment stored and released in the proglacial area, in particular from proglacial channels, was controlling suspended sediment transfer patterns. To characterize this control accurately requires multiple gauging stations with high frequency monitoring of suspended sediment concentration. Accurate characterization of this proglacial control on suspended sediment transfer may therefore aid interpretation of suspended sediment yield patterns from glacierized basins. Copyright © 2004 John Wiley & Sons, Ltd.     

Assessing damaged road verges as a suspended sediment source in the Hampshire Avon catchment,southern United Kingdom

Diffuse sediment pollution impairs water quality, exerts a key control on the transfer and fate of nutrients and contaminants and causes deleterious impacts on freshwater ecology. A variety of catchment sediment sources can contribute to such problems. Sediment control strategies and effective targeting of mitigation options therefore require robust quantitative information on the key sources of the sediment problem at catchment scale. Recent observations by Catchment Sensitive Farming Officers (CSFO's) in England have highlighted road verges damaged and eroded by passing vehicles, particularly large farm machinery, and livestock herd movement as visually important potential sources of local sediment problems. A study was therefore undertaken to assess the relative importance of damaged road verges as a suspended sediment source in three sub‐catchments of the Hampshire Avon drainage basin, southern UK. Road verge sediment contributions were apportioned in conjunction with those from agricultural topsoils and channel banks/subsurface sources. Time‐integrating isokinetic samplers were deployed to sample suspended sediment fluxes at the outlets of two control sub‐catchments drained by the Rivers Chitterne and Till selected to characterize areas with a low road network density and limited visual evidence of verge damage, as well as the River Sem sub‐catchment used to represent areas where road verge damage is more prevalent. The findings of a sediment source fingerprinting investigation based on a combination of intermittent sampling campaigns spanning the period 22/5/02–27/4/08 suggested that the respective overall mean relative sediment contributions from damaged road verges were 5 ± 3%, 4 ± 2% and 20 ± 2%. Relative inputs from damaged road verges for any specific sampling period in the River Sem sub‐catchment were as high as 33 ± 2%. Reconstruction of historical sources in the same sub‐catchment, based on the geochemical record stored in a floodplain depth profile, suggested that the significance of damaged road verges as a sediment source has increased over the past 15–20 years. The findings provide important information on damaged road verges as a primary source of suspended sediment and imply that catchment sediment control strategies and mitigation plans should consider such verges in addition to those agricultural and channel sources traditionally taken into account when attempting to reduce sediment pressures on aquatic resources. Copyright © 2010 John Wiley & Sons, Ltd.     

Tracing suspended sediment and particulate phosphorus sources in catchments

Information on suspended sediment and particulate P (PP) sources is an important requirement in many catchment-based diffuse source pollution studies, in order to assist with model validation and to provide information to support the development of effective sediment and phosphorus control strategies. Such information is, however, frequently unavailable or difficult to assemble. In the study reported, source fingerprinting procedures were successfully used to assemble this information for seven sub-catchments in the Hampshire Avon catchment and five sub-catchments in the Middle Herefordshire Wye catchment. The results provide important new information on the relative importance of the contributions from surface and channel/subsurface sources to the suspended sediment and PP fluxes from the catchments. In the Wye sub-catchments channel/subsurface sources contributed 40–55% of the overall suspended sediment flux and 21–43% of the PP flux from the catchments. Equivalent values for the Avon were 1–41% and 1–54%, respectively. Combination of the information on the relative importance of surface and channel/subsurface sources with measured suspended sediment fluxes has provided the first estimates of the specific fluxes of sediment and PP attributable to channel/subsurface sources for UK catchments. The former are as high as 15–20 t km⁻² year⁻¹ in some of the Wye sub-catchments, whereas the latter exceeded 0.1 kgP ha⁻¹ year⁻¹ in the same sub-catchments. The results emphasize the need to take account of potential contributions from channel/subsurface sources when using measured suspended sediment and PP flux data to validate predictions derived from models incorporating only surface contributions.     

Dynamics of suspended sediment transport and yield in a large agricultural catchment,southwest France

The dynamics of suspended sediment transport were monitored continuously in a large agricultural catchment in southwest France from January 2007 to March 2009. The objective of this paper is to analyse the temporal variability in suspended sediment transport and yield in that catchment. Analyses were also undertaken to assess the relationships between precipitation, discharge and suspended sediment transport, and to interpret sediment delivery processes using suspended sediment‐discharge hysteresis patterns. During the study period, we analysed 17 flood events, with high resolution suspended sediment data derived from continuous turbidity and automatic sampling. The results revealed strong seasonal, annual and inter‐annual variability in suspended sediment transport. Sediment was strongly transported during spring, when frequent flood events of high magnitude and intensity occurred. Annual sediment transport in 2007 yielded 16 614 tonnes, representing 15 t km^?2 (85% of annual load transport during floods for 16% of annual duration), while the 2008 sediment yield was 77 960 tonnes, representing 70 t km^?2 (95% of annual load transport during floods for 20% of annual duration). Analysis of the relationships between precipitation, discharge and suspended sediment transport showed that there were significant correlations between total precipitation, peak discharge, total water yield, flood intensity and sediment variables during the flood events, but no relationship with antecedent conditions. Flood events were classified in relation to suspended sediment concentration (SSC)–discharge hysteretic loops, complemented with temporal dynamics of SSC–discharge ranges during rising and falling flow. The hysteretic shapes obtained for all flood events reflected the distribution of probable sediment sources throughout the catchment. Regarding the sediment transport during all flood events, clockwise hysteretic loops represented 68% from river deposited sediments and nearby source areas, anticlockwise 29% from distant source areas, and simultaneity of SSC and discharge 3%. Copyright © 2010 John Wiley & Sons, Ltd.     

Dynamics of suspended sediment transport at field‐scale drain channels of irrigation‐dominated watersheds in the Sonoran Desert,southeastern California

Suspended sediment is a major source of pollution in irrigation‐dominated watersheds. However, little is known about the process and mechanisms of suspended sediment transport in drain channels directly connected to agricultural fields. This paper explains sediment dynamics using averaged 5 min flow discharge Q (m³ s^?1) and suspended sediment concentration C (mg l^?1) collected during one crop season in a small catchment containing a first‐order drain channel and its connected six agricultural fields within the Salton Sea watershed. The statistical properties and average trends of Q and C were investigated for both early (i.e. November) and late (i.e. January) stages of a crop season. Further in‐depth analysis on sediment dynamics was performed by selecting two typical single‐field irrigation events and two multiple‐field irrigation events. For each set of irrigation events, the process of suspended sediment transport was revealed by examining hydrograph and sediment graph responses. The mechanisms underlying suspended sediment transport were investigated by analysing the types of corresponding hysteresis loop. Finally, sediment rating curves for both hourly and daily data at early and late stages and for the entire crop season were established to seek possible sediment‐transport predictive model(s). The study suggests that the complicated processes of suspended sediment transport in irrigation‐dominated watersheds require stochastic rather than deterministic forecasting. Copyright © 2007 John Wiley & Sons, Ltd.     

Temporal variation of suspended sediment transport in the Koga catchment,North Western Ethiopia and environmental implications

Event sediment transport and yield were studied for 45 events in the upstream part of the 260 km² agricultural Koga catchment that drains to an irrigation reservoir. Discharge and turbidity data were collected over a period of more than a year, accompanied by grab sampling. Turbidity was very well correlated with the sediment concentrations from the samples (r = 0.99), which allowed us to estimate the temporal patterns of sediment concentrations within events. The hysteresis patterns between discharge and sediment concentrations were analysed to provide insight into the different sediment sources. Anticlockwise patterns are the dominant hysteresis patterns in the area, suggesting smaller contributions of suspended sediment from the river channels than from the hillslopes and agricultural areas. Complicated types of hysteresis patterns were mostly observed for long events with multiple peaks. For a given discharge, sediment yields in August and September, when the catchment was almost completely covered with vegetation, were much smaller than during the rest of the rainy season. The hysteresis patterns and timing suggest that the sediment availability from the agricultural areas and hillslopes affects sediment yields more strongly than does peak discharge. Two distinct types of sediment rating curves were observed for the season when the agricultural land was covered with vegetation and when it was not, indicating the dominating contribution of land use/cover to sediment yields in the catchment. The rate of suspended sediment transport in the area was estimated as 25.6 t year^?1 ha^?1. Copyright © 2013 John Wiley & Sons, Ltd.     

Modelling suspended sediment concentration and load in a transport‐limited alluvial gully in northern Queensland,Australia

Alluvial gullies are often formed in dispersible sodic soils along steep banks of incised river channels. Field data collected by Shellberg et al. (Earth Surface Processes and Landforms 38: 1765–1778, 2013) from a gully outlet in northern Australia showed little hysteresis between water discharge and fine (<63 µm) and coarse (>63 µm) suspended sediment, indicating transport‐limited rather than source‐limited conditions. The major source of the fine (silt/clay) component was the sodic soils of upstream gully scarps, and the coarser (sand) component was sourced locally from channel bed material. In this companion paper at the same study site, a new method was developed for combining the settling velocity characteristics of these two sediment source components to estimate the average settling velocity of the total suspended sediment. This was compared to the analysis of limited sediment samples collected during flood conditions. These settling velocity data were used in the steady‐state transport limit theory of Hairsine and Rose (Water Resources Research 28: 237–243, 245–250, 1992) that successfully predicted field data of concentrations and loads at a cross‐section, regardless of the complexity of transport‐limited upstream sources (sheet erosion, scalds, rills, gullies, mass failure, bank and bed erosion, other disturbed areas). The analysis required calibration of a key model parameter, the fraction of total stream power (F ≈ 0.025) that is effective in re‐entraining sediment. Practical recommendations are provided for the prediction of sediment loads from other alluvial gullies in the region with similar hydrogeomorphic conditions, using average stream power efficiency factors for suspended silt/clay (F_w ≈ 0.016) and sand (F_s ≈ 0.038) respectively, but with no requirement for field data on sediment concentrations. Only basic field data on settling velocity characteristics from soil samples, channel geometry measurements, estimates of water velocity and discharge, and associated error margins are needed for transport limit theory predictions of concentration and load. This theory is simpler than that required in source‐limited situations. Copyright © 2015 John Wiley & Sons, Ltd.     

The influence of dilution on downstream channel sedimentation in large rivers: the Yellow River,China

Due to the temporal decoupling of water and sediment sources in a large river basin, a flood from a sediment source area with high suspended sediment concentration (SSC) may be diluted by flow from a major runoff source area with low SSC. In this paper, this dilution effect is considered for 145 flood events from the Yellow River, China. Two indices (β₁ and β₂) describing the dilution effect are proposed, based on water and sediment from the clear water source area and the coarse sediment producing area. Regression equations between channel sedimentation (S_dep) and β₁ and β₂ are established based on flood events and annual data, respectively. The results show that dilution reduces channel sedimentation in the lower reaches by 34?1% and that this is related to a reduced frequency of hyperconcentrated flows in the lower reaches. The Longyangxia Reservoir for hydro‐electric generation has stored huge quantities of clear runoff from the upper Yellow River during high‐flow season since 1985, greatly reducing the dilution of the hyperconcentrated floods and therefore enhancing sedimentation in the lower reaches. For the purpose of reducing sedimentation, changing the operational mode of the Longyangxia Reservoir to restore the dilution effect is suggested. Copyright © 2013 John Wiley & Sons, Ltd.     

Effect of storms during drought on post‐wildfire recovery of channel sediment dynamics and habitat in the southern California chaparral,USA

Current global warming projections suggest a possible increase in wildfire and drought, augmenting the need to understand how drought following wildfire affects the recovery of stream channels in relation to sediment dynamics. We investigated post‐wildfire geomorphic responses caused by storms during a prolonged drought following the 2013 Springs Fire in southern California (USA), using multi‐temporal terrestrial laser scanning and detailed field measurements. After the fire, a dry‐season dry‐ravel sediment pulse contributed sand and small gravel to hillslope‐channel margins in Big Sycamore Creek and its tributaries. A small storm in WY 2014 generated sufficient flow to mobilize a portion of the sediment derived from the dry‐ravel pulse and deposited the fine sediment in the channel, totaling ~0.60 m³/m of volume per unit length of channel. The sediment deposit buried step‐pool habitat structure and reduced roughness by over 90%. These changes altered sediment transport characteristics of the bed material present before and after the storm; the ratio of available to critical shear stress (τ_o/τ_c) increased by five times. Storms during WY 2015 contributed additional fine sediment from tributaries and lower hillslopes and hyperconcentrated flow transported and deposited additional sediment in the channel. Together these sources delivered sediment on the order of six times that in 2014, further increasing τ_o/τ_c. These storms during multi‐year drought following wildfire transformed channel dynamics. The increased sediment transport capacity persisted during the drought period characterized by the longer residence time of relatively fine‐grained post‐fire channel sedimentation. This contrasts with wetter years, when post‐fire sediment is transported from the fluvial system during the same season as the post‐fire sediment pulse. Results of this short‐term study highlight the complex and substantial effects of multi‐year drought on geomorphic responses following wildfire. These responses influence pool habitat that is critical to longer‐term post‐wildfire riparian ecosystem recovery. Copyright © 2017 John Wiley & Sons, Ltd.     

Mineral magnetic characterization of sediment sources from an analysis of lake and floodplain sediments in the catchments of the Old Mill reservoir and Slapton Ley,South Devon,UK

Research on suspended sediment transport in the catchments of the Old Mill reservoir and Slapton Lower Ley, South Devon, has attempted to discriminate changing catchment sources on the basis of downcore variations in the mineral magnetic properties of lake, reservoir and floodplain sediments. Here, we examine these downcore variations and also explore the variability in catchment sources and the influence of topographic controls on mineral magnetic signatures of topsoils and subsoils. Particle size controls on the mineral magnetic signatures are explored by an analysis of a fractionated sediment sample, whilst the possible impact of diagenesis is assessed by an examination of the Mn profiles in the lake and reservoir sediments. From this analysis it is evident that the mineral magnetic signatures of well sorted floodplain deposits are more likely to reflect the particle size composition of the transported material. By contrast, the mineral magnetic record in the sediment of Slapton Ley appears to be most strongly influenced by dissolution of magnetic minerals. The sediment of the Old Mill reservoir provides the only suitable record for the application of a simple mixing model which is developed in order to quantify changes in the relative contribution of topsoil and subsoil through time. The research has important implications for attempting to reconstruct sediment sources in highly eutrophic lakes and emphasizes the uncertainty in the application of simple mixing models. © 1998 John Wiley & Sons, Ltd.     

Particle size analysis of the sediment suspended in a proglacial stream: Glacier De tsidjiore Nouve,Switzerland

Hourly, at-a-point samples of suspended sediment taken from the outflow stream of Glacier de Tsidjiore Nouve, Switzerland, over a 60 day sampling period (n = 1440) are shown to be dominantly composed of silt-sized particles. Particle size, SEM, and XRD analyses indicate a subglacial provenance for the suspended sediment. Temporal variations in particle size and sorting correspond poorly to fluctuations in water discharge, being dominated by erratic hour-to-hour fluctuations and clockwise hysteresis over diurnal flow events. Examination of grain size and sorting dynamics over snowmelt- and icemelt-related ablation events, during precipitation events, and during glacier drainage events enables some inferences to be drawn regarding sediment source areas and supply regimes. We conclude that although the bulk of the suspended sediment in the proglacial stream of Glacier de Tsidjiore Nouve is derived directly from subglacial sources (with occasional contributions from the valley train during rapid snowmelt and heavy rainfall periods), a portion of the suspended load undergoes intermittent ‘flush-fall’ transfer through the proglacial zone, which acts as a sediment source during rising flows and as a sink during periods of waning flow.     

Identifying subsoil sediment sources with carbon and nitrogen stable isotope ratios

Increased sediment loads from accelerated catchment erosion significantly degrade waterways worldwide. In the South East Queensland region of Australia, sediment loads are degrading Moreton Bay, a Ramsar listed wetland of international significance. In this region, like most parts of coastal Australia, sediment is predominantly derived from gully and channel bank erosion processes. A novel approach is presented that uses carbon and nitrogen stable isotope ratios and elemental composition to discriminate between these often indistinguishable subsoil sediment sources. The conservativeness of these sediment properties is first tested by examining the effect of particle size separation (testing for consistency during transport) and the effect of sampling at different times (testing for temporal source consistency). The discrimination potential of these sediment properties is then assessed with the conservative properties, based on the particle size and temporal analyses, modelled to determine sediment provenance in three catchments. Nitrogen sediment properties were found to have significant particle size enrichment and high temporal variance indicative of non‐conservative behaviour. Conversely, carbon stable isotopes had very limited particle size and temporal variability highlighting their suitability for sediment tracing. Channel erosion was modelled to be a significant source of sediment (μ 51%, σ 9%) contrasting desktop modelling research that estimated gully erosion is the predominant sediment source. To limit the supply of sediment to Moreton Bay, channel bank and gully erosion must both be targeted by sediment management programs. By distinguishing between subsoil sediment sources, this approach has the potential to enhance the management of sediment loads degrading waterways worldwide. Copyright © 2014 John Wiley & Sons, Ltd.     

The Ganges and Brahmaputra rivers in Bangladesh: basin denudation and sedimentation

Every year the Ganges and Brahmaputra rivers in Bangladesh transport 316 and 721 million tonnes of sediment, respectively. These high loads of suspended sediment reflect the very high rate of denudation in their drainage basins. The average mechanical denudation rate for the Ganges and Brahmaputra basins together is 365 mm 10³ yr⁻¹. However, the rate is higher in the Brahmaputra Basin than that in the Ganges Basin. Several factors, including mean trunk channel gradient, relief ratio, runoff, basin lithology and recurring earthquakes are responsible for these high denudation rates. Of the total suspended sediment load (i.e. 1037 million tonnes) transported by these rivers, only 525 million tonnes (c. 51% of the total load) are delivered to the coastal area of Bangladesh and the remaining 512 million tonnes are deposited within the lower basin, offsetting the subsidence. Of the deposited load, about 289 million tonnes (about 28% of the total load) are deposited on the floodplains of these rivers. The remaining 223 million tonnes (about 21% of the total load) are deposited within the river channels, resulting in aggradation of the channel bed at an average rate of about 3·9 cm yr⁻¹. Although the Brahmaputra transports a higher sediment load than the Ganges, the channel bed aggradation rate is much higher for the Ganges. This study also documents a wide range of interannual, seasonal and daily variation in suspended sediment transport and water discharge. Interannual variation in sediment deposition within the basin is also suggested. Copyright © 1999 John Wiley & Sons, Ltd.     

The nature and transport of the fine‐grained component of Swift Creek Landslide,Northwest Washington

Extreme sedimentation in Swift Creek, located in the Cascades foothills in NW Washington (48°55′N, 122°16′W), results from erosion of the oversteepened, unvegetated toe of a large (55 hectares) active landslide. Deposition of landslide‐derived sediment has necessitated costly mitigation projects in the channel including annual dredging and temporary sediment traps in an attempt to reduce the risk of flooding and damage to man‐made structures downstream. This study attempts to understand the process of sediment production along with the corresponding erosion rates of the sediment source to help with the development of mitigation plans and construction of optimal sediment reservoirs. The bedload and suspended sediment in the creek are a direct result of the weathering process of the serpentinitic bedrock underlying the landslide. The serpentinite does not weather to smectite clay, as previously thought. Instead, it weathers to asbestiform chrysotile with minor amounts of chlorite, illite and hydrotalcite, all of which occur in clay seeps on the unvegetated surface of the landslide. The chrysotile fibers average 2 µm in length and make up at least 50%, by volume, of the suspended load transported in Swift Creek. This study does not address the environmental or health implications of the asbestiform chrysotile transport or deposition. During the sampled time between February 2005 and February 2006, 127 discrete suspended sediment samples were collected and discharge was measured 66 times. The suspended sediment concentrations ranged from 0·02 g L^?1 to 41·6 g L^?1 and the discharge ranged from 0·0 m³ s^?1 to 0·5 m³ s^?1. A nonlinear functional model estimated the total suspended sediment flux from detailed precipitation records and discrete suspended sediment concentration and discharge measurements to be 910 t km^?2 yr^?1. When the suspended sediment flux is coupled with estimates of downstream deposition of coarse sediment, the estimated erosion rate for the entire Swift Creek landslide is 158 mm yr^?1. The majority of the material entering Swift Creek is presumed to originate on the unvegetated toe of the landslide, for which the erosion rate is thus approximately 1 m yr^?1. Copyright © 2010 John Wiley & Sons, Ltd.     

Magnetic enhancement in wildfire‐affected soil and its potential for sediment‐source ascription

Intense rainfall following wildfire can cause substantial soil and sediment redistribution. With concern for the increasing magnitude and frequency of wildfire events, research needs to focus on hydrogeomorphological impacts of fire, particularly downstream fluxes of sediment and nutrients. Here, we investigate variation in magnetic enhancement of soil by fire in burnt eucalypt forest slopes to explore its potential as a post‐fire sediment tracer. Low‐frequency magnetic susceptibility values (χ_lf) of <10 µm material sourced from burnt slopes (c. 8·0–10·4 × 10^?6 m³ kg^?1) are an order of magnitude greater than those of <10 µm material derived from long‐unburnt areas (0·8 × 10^?6 m³ kg^?1). Susceptibility of anhysteretic remanent magnetization (χARM) and saturation isothermal remanent magnetization (SIRM) values are similarly enhanced. Signatures are strongly influenced by soil and sediment particle size and storage of previously burnt material in footslope areas. Whilst observations indicate that signatures based on magnetic enhancement show promise for post‐fire sediment tracing, problems arise with the lack of dimensionality in such data. Magnetic grain size indicators χ_fd%, χARM/SIRM and χ_fd/χARM offer further discrimination of source material but cannot be included in numerical unmixing models owing to non‐linear additivity. This leads to complications in quantitatively ascribing downstream sediment to source areas of contrasting burn severity since sources represent numerical multiples of each other, indicating the need to involve additional indicators, such as geochemical evidence, to allow a more robust discrimination. Copyright © 2005 John Wiley & Sons, Ltd.     

Reconstructing the development of a gully in the Upper Kalaus basin,Stavropol region (southern Russia)

The Stavropol region of southern Russia is severely affected by human‐induced gully erosion. A lack of detailed information on the different stages of gully formation resulting from major agricultural expansion c. 100 years ago, is an obstacle for management and containment of these systems. In this study we combine measurements of particle‐bound radionuclides (¹³⁷Cs, ²¹⁰Pb_ex, ²²⁶Ra, ²³²Th and ⁴⁰K) and classical geomorphology to investigate and reconstruct the different phases of development of a gully during the last c. 100 years. We believe the ?rst phase (1) involved an initial incision into the bottom of a small valley (catchment area c. 1 km²) about 100 years ago. A short period of rapid growth was followed by a longer stage of gully stabilization. Subsequent phases were: (2) the period 1954–1960 – re‐incision in the lower gully reach was initiated by a high‐magnitude rainfall event, and a substantial amount of sediment was delivered to the gully fan; (3) c. 1960–1986 – the knickpoint retreated slowly, sediment was redeposited nearby, and the fan surface became stable; (4) 1986–1987 – a dam was built in the gully mouth and breached shortly after construction following 2 days of high rainfall, and substantial sediment accumulated in the gully above the dam and below the spillway channel on the fan surface; (5) 1987–1993 – the knickpoint retreat continued and the lower fan surface was stable until 1993 when the last signi?cant runoff event overlayed it with c. 10 cm of fresh sediment. These detailed reconstructions of gully development stages allow the contribution of high‐magnitude events to gully growth and regional sediment delivery to be assessed. They further guide management actions to prevent such dam failures in the future. Copyright © 2004 John Wiley & Sons, Ltd.     

Evaluating sampling efficiency when estimating sediment source contributions to suspended sediment in rivers by fingerprinting

A general method is proposed which measures the increase in uncertainty when sampling effort is reduced in sediment fingerprinting. The method gives quantitative measures of how reduced sampling of material in one of the source areas, and/or of suspended sediment in streams, increases the uncertainties in the proportions of sediment contributed from the sources. Because the proportions of sediment contributed by the source areas must add to one, standard errors of the estimated proportions cannot be used as the usual measures of uncertainty: the paper uses instead the volume of the joint 95% confidence region for the estimated proportions. The paper shows how the uncertainty in this volume changes as numbers of suspended sediment samples, and the numbers of samples collected from cropped fields, are reduced by successive steps from 24 (20, in the case of cropped fields) to 16, 12, 8, 4 and 2 samples. As expected, uncertainty increases rapidly as the number of samples – whether of suspended sediment or from cropped fields – is reduced drastically. The pattern of increasing uncertainty is similar both for reductions in suspended sediment sampling, and for reduced sampling from cropped areas. When the number of suspended sediment samples, and the number of samples from cropped fields, are reduced to the same values, the increase in uncertainty from fewer suspended sediment samples was always slightly greater than the increased uncertainty from the reduced sampling of cropped areas, although this finding took no account of differences in the costs of field sampling and laboratory analysis. Copyright © 2016 John Wiley & Sons, Ltd.