Determining Q of near-surface materials from Rayleigh waves

High-frequency (≥2 Hz) Rayleigh wave phase velocities can be inverted to shear (S)-wave velocities for a layered earth model up to 30 m below the ground surface in many settings. Given S-wave velocity (V_S), compressional (P)-wave velocity (V_P), and Rayleigh wave phase velocities, it is feasible to solve for P-wave quality factor Q_P and S-wave quality factor Q_S in a layered earth model by inverting Rayleigh wave attenuation coefficients. Model results demonstrate the plausibility of inverting Q_S from Rayleigh wave attenuation coefficients. Contributions to the Rayleigh wave attenuation coefficients from Q_P cannot be ignored when Vs/V_P reaches 0.45, which is not uncommon in near-surface settings. It is possible to invert Q_P from Rayleigh wave attenuation coefficients in some geological setting, a concept that differs from the common perception that Rayleigh wave attenuation coefficients are always far less sensitive to Q_P than to Q_S. Sixty-channel surface wave data were acquired in an Arizona desert. For a 10-layer model with a thickness of over 20 m, the data were first inverted to obtain S-wave velocities by the multichannel analysis of surface waves (MASW) method and then quality factors were determined by inverting attenuation coefficients.     

Modelling of viscoacoustic wave propagation in transversely isotropic media using decoupled fractional Laplacians

A new wave equation is derived for modelling viscoacoustic wave propagation in transversely isotropic media under acoustic transverse isotropy approximation. The formulas expressed by fractional Laplacian operators can well model the constant-Q (i.e. frequency-independent quality factor) attenuation, anisotropic attenuation, decoupled amplitude loss and velocity dispersion behaviours. The proposed viscoacoustic anisotropic equation can keep consistent velocity and attenuation anisotropy effects with that of qP-wave in the constant-Q viscoelastic anisotropic theory. For numerical simulations, the staggered-grid pseudo-spectral method is implemented to solve the velocity–stress formulation of wave equation in the time domain. The constant fractional-order Laplacian approximation method is used to cope with spatial variable-order fractional Laplacians for efficient modelling in heterogeneous velocity and Q media. Simulation results for a homogeneous model show the decoupling of velocity dispersion and amplitude loss effects of the constant-Q equation, and illustrate the influence of anisotropic attenuation on seismic wavefields. The modelling example of a layered model illustrates the accuracy of the constant fractional-order Laplacian approximation method. Finally, the Hess vertical transversely isotropic model is used to validate the applicability of the formulation and algorithm for heterogeneous media.     

Scattering and anelastic attenuation of seismic energy in northern Greece

The relative contribution of scattering (Q _s ^–1 ) and intrinsic (Q _i ^–1 ) attenuation to the totalS-wave attenuation for the frequencies of 1.5, 3.0, 6.0 and 12.0 Hz has been studied by applying the radiative energy transfer theory, Data of local earthquakes which occurred in northern Greece and were recorded by the permanent telementered network of the Geophysical Laboratory of the University of Thessaloniki have been used. The results show that in this area the scattering attenuation is dominant over all frequencies while intrinsic attenuation is significantly lower. The estimatedQ _s ^–1 andQ _i ^–1 values have frequency dependences off ^–0.72 andf ^–0.45, respectively. The frequency dependence ofQ _s ^–1 is the same as that of the codaQ _c ^–1 , obtained by applying the single scattering model, which probably implies that the frequency dependence of the coda wave attenuation is attributed to the frequency dependence of the scattering attenuation.Q _c ^–1 values are very close to scattering attenuation for short lapse times, (10–20 sec), and intermediate between scattering and intrinsic attenuation for the longer lapse times, (50–100 sec). This difference is explained as the result of the depth-dependent attenuation properties and the multiple scattering effects.     

Viscoacoustic least-squares reverse-time migration of different-order free-surface multiples

Multiples have longer propagation paths and smaller reflection angles than primaries for the same source–receiver combination, so they cover a larger illumination area. Therefore, multiples can be used to image shadow zones of primaries. Least-squares reverse-time migration of multiples can produce high-quality images with fewer artefacts, high resolution and balanced amplitudes. However, viscoelasticity exists widely in the earth, especially in the deep-sea environment, and the influence of Q attenuation on multiples is much more serious than primaries due to multiples have longer paths. To compensate for Q attenuation of multiples, Q-compensated least-squares reverse-time migration of different-order multiples is proposed by deriving viscoacoustic Born modelling operators, adjoint operators and demigration operators for different-order multiples. Based on inversion theory, this method compensates for Q attenuation along all the propagation paths of multiples. Examples of a simple four-layer model, a modified attenuating Sigsbee2B model and a field data set suggest that the proposed method can produce better imaging results than Q-compensated least-squares reverse-time migration of primaries and regular least-squares reverse-time migration of multiples.     

Intrinsic absorption and scattering attenuation in the southern part of the Netherlands

We present the first systematic study of attenuation derived from the S-wave coda in the frequency range 1-32 Hz for the southern part of the Netherlands and its surroundings. For this we used two methods, the codaQ (Q _c) method and the Multiple Lapse Time Window (MLTW) method. In the interpretation of the results both single and multiple scattering in a half space are considered. Our aim is to validate these interpretations in our region and to try to identify theeffects of attenuation due to intrinsic absoprtion (Q _i)and scattering attenuation (Q _s). For this we analyzedmore than 100 3-component high-quality digital seismograms from 43 crustalevents and 23 different stations in the Netherlands, Germany and Belgium.Coda Q results show smaller Q _c (=Q ₀fⁿ) values for epicentral distances shorter than 25 km (Q ₀=90) compared to larger epicentral distances (Q ₀=190), but similar frequency dependence (f^-0.9). Interpretation of MLTW results provided a seismic albedo smaller then 0.5, suggesting that the intrinsic absorption dominates over scattering in this region. Both Q _i and Q _s show similar frequency dependences as Q _c. These results are comparable to those obtained in other areas, but we also show that more sophisticated models are required to remove ambiguities in the interpretation. For short lapse times and shortevent-station distances we find for the simple half space model a correspondinginterpretation of both methodologies, where Q _c correspondsto Q _t, suggesting that a model with single scattering in ahalf space is appropriate. For long lapse times and long event station distances, however, we find that the S-wave coda is, most probably, too much influenced by crust-mantel heterogenities and more sophisticated Qinversion models using larger data sets are required for more reliable attenuation estimates.     

Frequency–wavenumber modelling and migration of 2D GPR data in moderately heterogeneous dispersive media

An algorithm for modelling and migrating ground penetrating radar (GPR) data in moderately heterogeneous dispersive media is presented. The method is based on wavefield extrapolation in the frequency–wavenumber (f–k) domain, from the solution of the 2D Maxwell's equations. The wavefield is extrapolated by a phase-shift technique using a constant relative permittivity K and a quality factor Q. It is then modified by a correction term to handle the lateral K and Q variations. The spatial distribution of the K and Q-factor values, representing the given model parameters, is introduced into the algorithm by a regular grid parametrization. The radar wave dispersion and attenuation, induced by relaxation processes, are taken into account by a linear frequency-dependent Q model, and expressed by a complex wavenumber in the propagation equation. A synthetic case and a field data set illustrate the potential of the method for frequencies of 300, 500 and 900 MHz. In the first case, a typical civil engineering problem is considered. The frequency dependence of the wave velocity and attenuation is well illustrated. The synthetic data are afterwards migrated using the initial model parameters. The results show the importance of using spatially varying model parameters in the migration processes. The second case concerns an application of the method to a real data set. In order to adjust the model parameters, a forward modelling sequence is performed until the best match between the measured and the synthetic data is achieved. A depth migration is then applied to the data, and the result is compared with the initial model parameters. In conclusion, we assess the contributions of the method to industrial applications, by discussing the performance of the algorithm compared with its limitations.     

A model for attenuation and scattering in the Earth's crust

The mechanisms contributing to the attenuation of earthquake ground motion in the distance range of 10 to 200 km are studied with the aid of laboratory data, coda wavesRg attenuation, strong motion attenuation measurements in the northeast United States and Canada, and theoretical models. The frequency range 1–10 Hz has been studied. The relative contributions to attenuation of anelasticity of crustal rocks (constantQ), fluid flow and scattering are evaluated. Scattering is found to be strong with an albedoB ₀=0.8–0.9 and a scattering extinction length of 17–32 km. The albedo is defined as the ratio of the total extinction length to the scattering extinction length. TheRg results indicate thatQ increases with depth in the upper kilometer or two of the crust, at least in New England. CodaQ appears to be equivalent to intrinsic (anelastic)Q and indicates that thisQ increases with frequency asQ=Q _o f ⁿ , wheren is in the range of 0.2–0.9. The intrinsic attenuation in the crust can be explained by a high constantQ (500Q _o2000) and a frequency dependent mechanism most likely due to fluid effects in rocks and cracks. A fluid-flow attenuation model gives a frequency dependence (QQ _o f ^0.5) similar to those determined from the analysis of coda waves of regional seismograms.Q is low near the surface and high in the body of the crust.     

Estimating permeability from field measurements of seismic attenuation in fractured chalk

Broadband (100–4000 Hz) cross‐hole seismic data have been acquired at a borehole test site where extensive hydrological investigations have previously been performed, including in situ estimates of permeability. The rock type is homogeneous chalk and fractures and bedding planes have been identified from well logs. High values of seismic attenuation, Q= 22 ≤ 27 ≤ 33, were observed over a 10 m depth interval where fracture permeability values of 20–50 darcy had been recorded. An attempt has been made to separate the attenuation due to scattering and intrinsic mechanisms. The estimated values of intrinsic attenuation, Q= 31 ≤ 43 ≤ 71, have been reproduced using a number of current theories of seismic‐wave propagation and fluid‐flow‐induced seismic attenuation in cracked and fractured media. A model that considers wavelength‐scale pressure gradients is the preferred attenuation mechanism. Model parameters were obtained from the hydro‐geological and seismic data. However, we conclude that it is not possible to use seismic Q to measure rock permeability remotely, principally because of the inherent uncertainties arising from model parameterisations.     

Approximating constant‐Q seismic propagation in the time domain

In this study, we investigate the accuracy of approximating constant‐Q wave propagation by series of Zener or standard linear solid (SLS) mechanisms. Modelling in viscoacoustic and viscoelastic media is implemented in the time domain using the finite‐difference (FD) method. The accuracy of numerical solutions is evaluated by comparison with the analytical solution in homogeneous media. We found that the FD solutions using three SLS relaxation mechanisms as well as a single SLS mechanism, with properly chosen relaxation times, are quite accurate for both weak and strong attenuation. Although the RMS errors of FD simulations using a single relaxation mechanism increase with increasing offset, especially for strong attenuation (Q = 20), the results are still acceptable for practical applications. The synthetic data of the Marmousi‐II model further illustrate that the single SLS mechanism, to model constant Q, is efficient and sufficiently accurate. Moreover, it benefits from less computational costs in computer time and memory.     

Attenuation properties of viscoelastic material

The attenuation properties of eight rheological models have been studied theoretically. The expressions forQ have been obtained by using dissipated and stored energies and/or complex modulus for each model. The dependence ofQ on frequency has been demonstrated. The three-element elastic model appears to be the best one to represent the viscoelastic nature of the earth's material for a finite value ofQ.     

Modeling of Wide-Angle Seismic Attributes Using the Gaussian Beam Method

In this study, observed seismic attributes from shot gather 11 of the SAREX experiment are used to derive a preliminary velocity and attenuation model for the northern end of the profile in southern Alberta. Shot gather 11 was selected because of its prominent Pn arrivals and good signal to noise ratio. The 2-D Gaussian beam method was used to perform the modeling of the seismic attributes including travel times, peak envelope amplitudes and pulse instantaneous frequencies for selected phases. The preliminary model was obtained from the seismic attributes from shot gather 11 starting from prior tomographic results. The amplitudes and instantaneous frequencies were used to constrain the velocity and attenuation structure, with the amplitudes being more sensitive to the velocity gradients and the instantaneous frequencies more sensitive to the attenuation structure. The resulting velocity model has a velocity discontinuity between the upper and lower crust, and lower velocity gradients in the upper and lower crust compared to earlier studies. The attenuation model has Q _p ^-1 values between 0.011 and 0.004 in the upper crust, 0.0019 in the lower crust and a laterally variable Q _p ^-1 in the upper mantle. The Q _p ^-1 values are similar to those found in Archean terranes from other studies. Although the results from a single gather are non-unique, the initial model derived here provides a self-consistent starting point for a more complete seismic attribute inversion for the velocity and attenuation structure.     

Attenuation of Coda Waves at the Changbaishan Tianchi Volcanic Area in Northeast China

21 earthquakes recorded by a temporary seismic network in the Changbaishan Tianchi volcanic area in Northeast China operated during the summer of 2002 and 2003 were analyzed to estimate the S coda attenuation. The attenuation quality factor Q_c was estimated using the single scattering attenuation model of Sato (1977) in the frequency band from 4 to 24 Hz. All the events studied in this paper occurred at depths from 2 to 6 km with ML of 1.4–2.8. The epicentral distances are less than 25 km. For all events which occurred near the Tianchi Lake (caldera), the Q_c patterns obtained at the stations near the lake are similar, and the Q_c values are relatively small. At the stations located about 15 km east of the Tianchi Lake, however, the average Q_c is significantly higher. For an event which occurred 25km from the lake to the west, Q_c patterns derived at the stations near the lake are quite similar to the above mentioned Q_c for stations located in the east. Further study shows that Q_c value in the north and central areas of the volcano is relatively lower than that in the surrounding area. Compared to other volcanic areas in the world, the average Q_c of the Changbaishan Tianchi volcanic area is obviously lower. The deep seismic sounding and teleseismic receiver function studies indicated more than one lower velocity layer in the crust. The MT studies suggested the presence of high conductive bodies beneath the area. We interpret the strong attenuation of coda waves near the Changbaishan Tianchi volcano as being possibly related to high temperature medium caused by shallow magma chambers.     

EXPERIMENTAL COMPARISON BETWEEN SPECTRAL RATIO AND RISE TIME TECHNIQUES FOR ATTENUATION MEASUREMENT*

Two techniques for the measurement of attenuation–spectral ratio and rise time techniques–were tested and compared in the laboratory. The spectral ratio technique proved to be reliable and easy to implement for intermediate values (5 < Q < 50) of attenuation. For low (Q > 50) and high attenuations, the spectral ratio technique is inaccurate. Calculating the rise time on simulated signals, we found a relation between rise time τ and the ratio travel-time to quality factor T/Q which could be approximated in intervals by the linear relation τ=τ+C*T/Q. The constants τ and C depend on the absolute value of T/Q and on the initial source signal. The rise time technique, performed on the first quarter period of the signal, enables high attenuations (Q < 5) to be measured. The determination of the relation between τ and T/Q is possible if one knows the initial source. We theoretically approximate this relation through a simulation using a realistic propagation model. With laboratory measurements made on Fontainebleau sandstone, we show that the rise time technique using the theoretical relation τ=τ(T/Q) gives comparable values of Q to those obtained from the spectral ratio technique. In borehole seismics, where it is often difficult to remove undesired signals, the rise time technique applied with the right (τ, T/Q) relation is the best method to use.     

Spatial variation of crustal codaQ in California

Coda wave data from California microearthquakes were studied in order to delineate regional fluctuations of apparent crustal attenuation in the band 1.5 to 24 Hz. Apparent attenuation was estimated using a single back scattering model of coda waves. The coda wave data were restricted to 30 s following the origin time; this insures that crustal effects dominate the results as the backscattered shear waves thought to form the coda would not have had time to penetrate much deeper. Results indicate a strong variation in apparent crustal attenuation at high frequencies between the Franciscan and Salinian regions of central California and the Long Valley area of the Sierra Nevada. Although the codaQ measurements coincide at 1.5 Hz (Q _c =100), at 24 Hz there is a factor of four difference between the measurements made in Franciscan (Q _c =525) and Long Valley (Q _c =2100) with the Salinian midway between (Q _c =900). These are extremely large variations compared to measures of seismic velocities of comparable resolution, demonstrating the exceptional sensitivity of the high frequency codaQ measurement to regional geology. In addition, the frequency trend of the results is opposite to that seen in a compilation of codaQ measurements made worldwide by other authors which tend to converge at high and diverge at low frequencies, however, the worldwide results generally were obtained without limiting the coda lengths and probably reflect upper mantle rather than crustal properties. Our results match those expected due to scattering in random media represented by Von Karman autocorrelation functions of orders 1/2 to 1/3. The Von Karman medium of order 1/3 corresponding to the Franciscan codaQ measurement contains greater amounts of high wavenumber fluctuations. This indicates relatively large medium fluctuations with wavelengths on the order of 100 m in the highly deformed crust associated with the Franciscan, however, the influence of scattering on the codaQ measurement is currently a matter of controversy.     

Characteristics of coda wave attenuation in Yunnan area

The characteristic of seismic coda wave attenuation in Yunnan area in 7 frequency-bands range from 1 Hz to 20 Hz was estimated by using the local earthquake's waveform data recorded from 22 Yunnan digital seismic stations.Coda attenuation Q-c1 of each station was firstly calculated by single scattering method. Then, mean free path Le and seismic albedo Bo of each station were calculated, and scattering attenuation Q-1s and intrinsic attenuation Q-1i were separated from total attenuation Q-1t by multiple lapse time window analysis based on the multiple scattering model in uniform random isotropic scattering medium. The attenuating characteristics in Yunnan show that most value of Le are in 10～30 km, with maximal within 2～6 Hz;Bo are about 0.5 at 1～2 Hz, but less than 0.5at other frequency-bands, which means Q-1i is comparable with Q-1s at 1～2 Hz, and after 1～2 Hz, Q-1i is greater than Q-1s and dominates the attenuation process. Q-1c is close to Q-1i at other frequency bands except 1～2 Hz.Results show that Q-1 especially Qs-1 varies spatially, Q-1 in eastern Yunnan zone is a bit higher than in northwestern Yunnan zone;northwestern Yunnan zone higher than southwestern Yunnan zone. Comparing with other results in global, Qs-1 in Yunnan is lower than the global average value among these results, Q-1i is higher than the global average value, and Q-1t lies the middle among these results.     

Attenuation of high-frequency earthquake waves in South America

Earlier attenuation studies for the South American continent indicate that for Sn and Lg waves there is low attenuation in the shield region east of the Andes, whereas in the west of South America, with some exceptions, there is high attenuation. Those studies, however, were nonquantitative. In this study theQ ₀ (1-Hz values) for Lg waves for South America are presented, based on a scattering model ofAki (1969) as extended byHerrmann (1980) for the coda waves of shallow local and near-regional earthquakes. The results of the codaQ method are compared with those obtained byNuttli's method (1973). TheseQ ₀ values are in good agreement with the apparentQ ₀ of Lg waves obtained by the latter method. The data were obtained from over 100 local and regional earthquakes recorded by 12 WWSSN stations throughout continental South America. They provided a range of frequencies from 0.4 to 1.4 Hz, for which the frequency dependence ofQ was investigated by assumingQ=Q ₀(f/f ₀). The observed data indicate that the tectonic region of western South America is characterized by lowQ ₀ and a large frequency-dependent factor , the values ranging from 150 to 350 and 0.4 to 0.7, respectively. TheQ ₀ values increase in the shield region east of the Andes, but frequency dependence decreases. The average crustalQ ₀ for north and central Argentina ranges from 420 to 580, and ranges from 0.2 to 0.3. TheQ ₀ is larger in the Brazil region, ranging from 580 to 980, and varies from 0.0 to 0.2. In the lower-attenuation region of eastern South America higher values of attenuation correlate with greater thickness of the sedimentary layers.     

Source/receiver array directivity effects on marine seismic attenuation measurements

Attenuation of seismic waves, quantified by the seismic quality factor Q, holds important information for seismic interpretation, due to its sensitivity to rock and fluid properties. A recently published study of Q, based on surface seismic reflection data, used a modified spectral ratio approach (QVO), but both source and receiver responses were treated as isotropic, based on simple raypath arguments. Here, this assumption has been tested by computing apparent attenuation generated by frequency-dependent directivity of typical marine source and receiver arrays and acquisition geometries. Synthetic wavelet spectra were computed for reflected rays, summed over the first Fresnel zone, from the base of a single interval, 50–3000 m thick and velocity 2000 m/s, overlying a 2200 m/s half-space, and for offsets of 71–2071 m. The source and receiver geometry were those of an actual survey. The modelled spectra are clearly affected by directivity, most strongly because of surface ghosts. In general, the strong high-frequency component, produced by the array design, leads to apparently negative attenuation in individual reflection events, though this is dependent on offset and target depth. For shallow targets (less than 400–500 ms two-way traveltime (TWT) depth), apparent Q-values as extreme as ?50 to ?100 were obtained. For deeper target depths, the directivity effect is far smaller. The implications of the model study were tested on real data. QVO was applied to 20 true-spectrum-processed CMPs, in a shallow (405–730 ms TWT) and a deeper (1000–1300 ms TWT) interval, firstly using a measured far-field source signature (effectively isotropic), and secondly using computed directivity effects instead. Mean interval Q^?1-values for the deeper interval, 0.029 ± 0.011 and 0.027 ± 0.018 for conventional and directional processing, respectively, suggested no directivity influence on attenuation estimation. For the shallow interval (despite poor spectral signal-to-noise ratios and hence scattered attenuation estimates), directional processing removed directivity-generated irregularities from the spectral ratios, resulting in an improvement from Q^?1_int = ?0.036 ± 0.130 to a realistic Q^?1_int = 0.012 ± 0.030: different at 94% confidence level. Equivalent Q-values are: for the deeper interval, 35 and 37 for conventional and directional processing, respectively, and ?28 and 86 for the shallow interval. These results support the conclusions of the model studies, i.e. that source/receiver directivity has a negligible effect except for shallow targets (e.g. TWT depth ≤ 500 ms) imaged with conventional acquisition geometry. In such cases directivity corrections to spectra are strongly recommended.     

CodaQ as a combination of scattering and intrinsic attenuation: Numerical simulations with the boundary integral method

Numerical modelling ofSH wave seismograms in media whose material properties are prescribed by a random distribution of many perfectly elastic cavities and by intrinsic absorption of seismic energy (anelasticity) demonstrates that the main characteristics of the coda waves, namely amplitude decay and duration, are well described by singly scattered waves in anelastic media rather than by multiply scattered waves in either elastic or anelastic media. We use the Boundary Integral scheme developed byBenites et al. (1992) to compute the complete wave field and measure the values of the direct waveQ and coda wavesQ in a wide range of frequencies, determining the spatial decay of the direct wave log-amplitude relation and the temporal decay of the coda envelope, respectively. The effects of both intrinsic absorption and pure scattering on the overall attenuation can be quantified separately by computing theQ values for corresponding models with (anelastic) and without (elastic) absorption. For the models considered in this study, the values of codaQ ^–1 in anelastic media are in good agreement with the sum of the corresponding scatteringQ ^–1 and intrinsicQ ^–1 values, as established by the single-scattering model ofAki andChouet (1975). Also, for the same random model with intrinsic absorption it appears that the singly scattered waves propagate without significant loss of energy as compared with the multiply scattered waves, which are strongly affected by absorption, suggesting its dominant role in the attenuation of coda waves.     

Anelasticity of the crust and upper mantle beneath north and central India from the inversion of observed Love and Rayleigh wave attenuation data

The fundamental mode Love and Rayleigh waves generated by earthquakes occurring in Kashmir, Nepal Himalaya, northeast India and Burma and recorded at Hyderabad, New Delhi and Kodaikanal seismic stations are analysed. Love and Rayleigh wave attenuation coefficients are obtained at time periods of 15–100 seconds, using the spectral amplitude of these waves for 23 different paths along northern (across Burma to New Delhi) and central (across Kashmir, Nepal Himalaya and northeast India to Hyderabad and Kodaikanal) India. Love wave attenuation coefficients are found to vary from 0.0003 to 0.0022 km^–1 for northern India and 0.00003 km^–1 to 0.00016 km^–1 for central India. Similarly, Rayleigh wave attenuation coefficients vary from 0.0002 km^–1 to 0.0016 km^–1 for northern India and 0.00001 km^–1 to 0.0009 km^–1 for central India. Backus and Gilbert inversion theory is applied to these surface wave attenuation data to obtainQ ^–1 models for the crust and uppermost mantle beneath northern and central India. Inversion of Love and Rayleigh wave attenuation data shows a highly attenuating zone centred at a depth of 20–80 km with lowQ for northern India. Similarly, inversion of Love and Rayleigh wave attenuation data shows a high attenuation zone below a depth of 100 km. The inferred lowQ value at mid-crustal depth (high attenuating zone) in the model for northern India can be by underthrusting of the Indian plate beneath the Eurasian plate which has caused a low velocity zone at this shallow depth. The gradual increase ofQ ^–1 from shallow to deeper depth shows that the lithosphere-asthenosphere boundary is not sharply defined beneath central India, but rather it represents a gradual transformation, which starts beneath the uppermost mantle. The lithospheric thickness is 100 km beneath central India and below that the asthenosphere shows higher attenuation, a factor of about two greater than that in the lithosphere. The very lowQ can be explained by changes in the chemical constitution taking place in the uppermost mantle.     

Three-dimensional Q structure in Jiashi earthquake region of Xinjiang

3-D S-waveQ structure in Jiashi earthquake region is inverted based on the attenuation of seismic waves recorded from earthquakes in this region in 1998 by the Research Center of Exploration Geophysics (RCEG), CSB, and a rough configuration of deep crustal faults in the earthquake region is presented. First, amplitude spectra of S-waves are extracted from 450 carefully-chosen earthquake records, called observed amplitude spectra. Then, after instrumental and site effect correction, theoretical amplitude spectra are made to fit observed amplitude spectra with nonlinear damped least-squares method to get the observed travel time overQ, provided that earthquake sources conform to Brune’s disk dislocation model. Finally, by 3-D ray tracing method, theoretical travel time overQ is made to fit observed travel time overQ with nonlinear damped least-squares method. In the course of fitting, the velocity model, which is obtained by 3-D travel time tomography, remains unchanged, while onlyQ model is modified. When fitting came to the given accuracy, the ultimateQ model is obtained. The result shows that an NE-trending lowQ zone exists at the depths of 10–18 km, and an NW-trending lowQ zone exists at the depths of 12–18 km. These roughly coincide with the NE-trending and the NW-trending low velocity zones revealed by other scientists. The difference is that the lowQ zones have a wider range than the low velocity zones. Foundation item: Joint Seismological Science Foundation of China (957-07-414) and State Key Basic Research Development and Programming Project (95-13-02-02). Contribution No. RCEG200105, Research Center of Exploration Geophysics, China Seismological Bureau.