共查询到20条相似文献,搜索用时 390 毫秒
1.
针对应力比结构性参数存在的问题,建立了结构性黄土初始结构性参数与含水率、围压之间的关系,在变形过程中建立了更为合理的结构性参数与广义剪应变的关系,并将其引入结构性黄土的强度理论中。在此基础上,通过数值计算对边坡结构性参数分布的变化规律及潜在滑动面的确定进行了评价。研究结果表明:建立的初始结构性参数可以反映黄土边坡的结构性参数初始分布场;结构性参数变化的上限是初始结构性参数,下限为结构性完全丧失后的结构性参数,且其值等于1.0;在结构性黄土边坡稳定性分析中,通过结构性参数的分布规律可在一定程度上确定边坡的潜在滑动面,但仅适用于塑性区域呈明显的带状集中分布的情况。 相似文献
2.
改进的遗传算法在堆石体参数反演中的应用 总被引:1,自引:0,他引:1
在研究堆石坝问题中,堆石体参数的合理估计非常重要,根据工程实测值反演堆石体参数不失为一种有效估计参数的新思路。在传统遗传算法操作过程中,引入模拟退火的Metropolis接受准则,并结合系统识别的基本原理改进了遗传算法。将改进的新算法应用于堆石坝主要堆石料的参数反演,结果显示其误差很小、收敛速度快、精度高的优越性,克服了传统的梯度优化方法和单纯形法所具有的搜索速度随反演参数增多呈级数减慢、容易陷入局部极值点和误差传递导致不收敛等缺点,值得在本领域参数优化中推广。 相似文献
3.
洞室围岩的某些参数,如弹性模量、强度参数等,对地下洞室的施工和设计具有极其重要的作用,直接进行这些参数的现场测量势必要耗费大量的物资和精力,在这种背景下,位移反分析的工程应用具有很重要的理论和实用价值。但洞室工程中大量不确定性因素的存在使得监测结果不可避免地存在随机性,有时会使得变形监测结果产生较大的误差,甚至失真。因此以监测结果的绝对值所反演得到的参数可能是错误的。在这种情况下,以监测数据的相对值进行参数反演在一定程度上可以消除测量误差。基于相对位移的随机反分析法并结合DFP优化算法开发了基于相对位移的随机反分析法,将其应用于一具体洞室工程中反演其弹性模量取得了较为理想的效果。 相似文献
4.
在浙赣一带山前冲(洪)积地层中,普遍分布一层稍密状砾砂层,岩土工程地质勘察评价中,较难取原状土作土工试验、野外静力触探试验,多采用N63.5动力触探,确定其岩土物理力学性质、状态。但作为基桩持力层时的桩基参数的确定,缺乏可靠依据,以致于忽视其利用价值,该层在桩基方面的应用值得研究。本文通过稍密状砾砂层作为沉管灌注桩持力层的桩静荷载资料,根据数理统计原理,采用反演法进行推算桩基参数,并通过对应地层的N63.5动力触探数据及经验数值,进行复核,获得相应桩基参数,并对N63.5与桩基参数进行相关性分析探讨,获得Q-N63.5相关式,直接可应用于桩基参数的确定。该成果在岩土工程勘察中具有一定的指导意义。 相似文献
5.
6.
《岩土力学》2016,(6):1737-1744
模糊评判系统在边坡稳定性综合评价中的应用越来越广泛。由于岩体材料参数在实际工程中是离散的,将材料参数作为评价因子时,需首先对其本身进行评价得出表征参数,然后再参与到综合评价系统中。以大岗山坝肩边坡为例,从岩体自身抵抗外界影响的角度出发,考虑到位移和安全系数在边坡失稳前、后的变化幅度和变化次序问题,对岩体特性进行深入研究。通过对各参数进行分层敏感性分析并评价,得到表征参数;通过面积分配法得到隶属度;以安全系数和位移两个目标量,对岩体物理力学参数进行综合敏感性分析,以敏感度定义各因子的权重,将其结果应用于评价系统中。敏感性分析结果显示:以位移为目标量时,变形主要依赖于抗剪强度参数中的凝聚力;以安全系数为目标量时,内摩擦角对边坡失稳的影响略大于凝聚力;位移敏感性强于安全系数敏感性。综合评价结果显示:岩体力学参数具有较强的强度,以安全系数为目标量的评价结果优于以位移为目标量的评价结果,与敏感性分析结果一致,符合一般规律和实际情况,从而证明研究方法的正确性。 相似文献
7.
8.
9.
姚仰平等提出的广义非线性强度理论,将各种摩擦材料的非线性强度理论统一起来,使统一后的非线性强度理论能够合理地反映各类摩擦材料的强度特性。在广义非线性强度理论体系中,形状参数?是影响在?平面上破坏曲线形状的重要因素之一,因此,需要对形状参数进行如下研究:(1)将广义非线性理论应用于各类砂土中,根据其在?平面上破坏曲线特性,在判断该破坏曲线凹凸的基础上,得到砂土形状参数?临界值与破坏应力比参数Mf之间的关系;(2)通过对几个经典砂土真三轴试验结果的整理,验证广义非线性强度理论对砂土破坏特性的预测能力,并在此基础上建立该理论中形状参数?和破坏应力比参数Mf的线性关系。因此,在实际应用时,仅通过三轴压缩试验即可得到三维应力条件下的强度包线。 相似文献
10.
11.
GPS控制站控制半径的探讨 总被引:1,自引:1,他引:0
笔者通过对200个以上测点用不同GPS控制站的控制参数,用随机软件分别计算单个测点的三维坐标(即x、y、h),并计算测点与控制站之间的距离以及坐标、高程的差值,采用线性回归和正态直方图两种分析方法展示距离与差值之间的关系,得出距离与差值之间不存在线性关系。因此,在本项目的后续工作过程中将GPS控制站的控制半径适当延长至80km(试验的距离范围0~88.621km)。由此建议在以后不同比例尺的GPS定位测量中应增加对GPS控制站控制半径的试验对比工作,不同区域可能有所差异,则工作方法也有所不同。在满足《规范》和《任务书》的条件下,灵活部署具体工作的实施方法。 相似文献
12.
13.
以豫北山前冲洪积扇含水层为研究对象,探讨1:5万冲洪积扇含水层水质调查方法。该方法由工作量预部署、野外调查和取样点布设3个阶段组成。工作量预部署阶段,以前期调查资料为基础,编制工作区地形地貌、潜在污染源、地下水流场和水化学类型演变图,并赋值叠加形成不同调查点密度分区的野外工作图,宏观控制调查工作量; 野外调查阶段,重视pH值、溶解氧、电导率和氧化还原电位的测定与质量控制,根据调查区块环境状况调整调查点密度,布点兼顾地下水点与非地下水点及不同深度水点间的比例; 取样点布设阶段,以地质环境对含水层进行分区,以不同深度水井地下水功能对含水层进行分层。利用调查点现场水化学参数,识别并圈定水质变异区,分别采用判断法和均布法布设水质变异区和水质正常演化区取样点。该方法可为类似地区开展高精度地下水水质或污染调查提供参考。 相似文献
14.
中原油田高压注水诱发的油水井套管损坏原因分析 总被引:2,自引:0,他引:2
中原油田高压注水开发35年,套管损坏严重,严重的影响了油田的开发效果。据研究,油田水井套管损坏主要有错断、变形及破漏等三类,平面上主要分布在断层发育区、高地层水矿化度区、泥岩层和盐膏层发育区,剖面上主要分布在盐膏层段和主力生产井段。提出断层活动、地应力非均质演化、盐岩蠕变、油田开发历程和开采方式及油气流场、化学场演化是中原油田套损的主要控制因素,建立油田油藏油井多参数动态模式,优选与油藏模式匹配的开采方式及增产措施,改造套管动力学环境和化学环境将能防治套损地质灾害的发生。 相似文献
15.
全站仪导线测量是平面控制测量的一种主要测量方法。针对全站仪导线能够即时直接得到待定点的近似坐标的特点,结合导线测量实例,提出了便于实际应用的近似坐标间接平差方法,并给出了实际操作的公式。与经纬仪导线测量相比,避免了方位角的推算和改正,以及坐标增量的计算和改正,工作效率高,而且不易出错,同时可以看出传统附和导线测量需要两条已知边,作为方位角的检核条件,而全站仪导线间接平差,只需要一条已知边和一个已知点即可.使导线的布网更加灵活. 相似文献
16.
The paper [Wang, J.-J., Zhu, J.-G., Chiu, C.F., Zhang, H., 2007. Experimental study on fracture toughness and tensile strength of a clay. Engineering Geology 94, 64–75.] focuses on two important fracture parameters of soils: tensile strength and fracture toughness. These parameters control the behaviour of soils in a wide range of situations, from the design of a simple footing to much complicated fracture behaviour of clay liners or covers. The authors have done extensive laboratory work to determine these two parameters and their laborious and complicated experimental program needs praise. However, some of the points raised in their conclusions, based on the analysis and comparison with the data from the literature, need to be discussed. 相似文献
17.
18.
Nadav Sorek Eduardo Gildin Fani Boukouvala Burcu Beykal Christodoulos A. Floudas 《Computational Geosciences》2017,21(2):247-266
The objective of this paper is to introduce a novel paradigm to reduce the computational effort in waterflooding global optimization problems while realizing smooth well control trajectories amenable for practical deployments in the field. In order to overcome the problems of slow convergence and non-smooth impractical control strategies, often associated with gradient-free optimization (GFO) methods, we introduce a generalized approach which represent the controls by smooth polynomial approximations either by a polynomial function or by a piecewise polynomial interpolation, which we denote as function control method (FCM) and interpolation control method (ICM), respectively. Using these approaches, we aim to optimize the coefficients of the selected functions or the interpolation points in order to represent the well-control trajectories along a time horizon. Our results demonstrate significant computational savings, due to a substantial reduction in the number of control parameters, as we seek the optimal polynomial coefficients or the interpolation points to describe the control trajectories as opposed to directly searching for the optimal control values (bottom hole pressure) at each time interval. We demonstrate the efficiency of the method on two and three-dimensional models, where we found the optimal variables using a parallel dynamic-neighborhood particle swarm optimization (PSO). We compared our FCM-PSO and ICM-PSO to the traditional formulation solved by both gradient-free and gradient-based methods. In all comparisons, both FCM and ICM show very good to superior performances. 相似文献
19.
Experimental analysis of different software packages for orientation and digital surface modelling from UAV images 总被引:1,自引:0,他引:1
Giovanna Sona Livio Pinto Diana Pagliari Daniele Passoni Rossana Gini 《Earth Science Informatics》2014,7(2):97-107
The use of UAVs finds application in a variety of fields, among which are the small scale surveys for environmental protection application. In this frame some experimental tests were carried out at Politecnico di Milano to assess metric accuracies of images acquired by UAVs and derived photogrammetric products. A block of 5 strips and 49 photos was taken by fixed wing system SenseFly, carrying a camera Canon Ixus 220HS on a rural area included in an Italian Park. Images are processed through bundle adjustment, automatic DEM extraction and orthoimages production steps with several software packages, with the aim to evaluate their characteristics, capabilities and weaknesses. The software packages tested were Erdas-LPS, EyeDEA (University of Parma), Agisoft Photoscan, Pix4UAV, PhotoModeler Scanner. For the georeferencing of the block 16 pre-signalized ground control points were surveyed in the area through GPS (NRTK survey). Comparison of results is given in terms of differences among orientation parameters and their accuracies. Moreover, comparisons among different digital surface models are evaluated. Furthermore, exterior orientation parameters, image points and ground points coordinates, obtained by the various software packages, were used as initial values in a comparative adjustment made by scientific in-house software. Paper confirms that computer vision software are faster in computation and, even if their main goal is not to pursue high accuracy in points coordinates determination, they seems to produce results comparable to those obtainable with standard photogrammetric approach. Agisoft Photoscan seems in this case to yield the best results in terms of quality of photogrammetric products. 相似文献