黏土中隔舱吸力式钢圆筒安装及水平受荷试验研究

近年来大直径钢圆筒结构在离岸人工岛工程中得到应用,如港珠澳大桥人工岛即采用振动下沉的方式安装钢圆筒,该方法对施工条件、装备以及施工控制技术要求较高。提出一种新型隔舱吸力式钢圆筒结构,在钢圆筒内部设置隔舱板,将结构分为上下两个隔舱,通过对下舱抽气实现隔舱吸力式钢圆筒在负压作用下的下沉安装。设计了隔舱吸力式钢圆筒安装及水平承载力模型试验,对比了负压贯入的隔舱吸力式钢圆筒和压力贯入的传统钢圆筒结构的贯入阻力及承载特性,分析了改变隔舱吸力式钢圆筒上下舱高度比L₁/L₂对其沉贯过程及承载特性的影响。结果表明,采用负压吸力沉贯的隔舱吸力式钢圆筒相比于采用压力贯入的传统钢圆筒结构的贯入阻力减小,水平极限承载力提高。在极限水平荷载作用下,随着隔舱吸力式钢圆筒的L₁/L₂从2.28减小到1.00、0.56,转动中心位置上移,水平极限承载力及弯矩承载力得到显著提高。     

粘土中吸力锚沉贯阻力与土塞形成试验研究

针对粘土中吸力锚沉贯的两个关键性问题--沉贯阻力和土塞形成过程,在自行研制的试验平台上进行一系列吸力锚沉贯室内模型试验.试验结果表明,负压抽吸对筒壁内部土体的影响较大,而对外侧土体的影响很小;由压力沉贯向吸力沉贯转换后,土体阻力会先降低,再随着沉贯的进行逐渐增大,并超过采用压贯方式的土体阻力;前期压贯深度的变化带来了不同的内部泥面下陷,这对吸力沉贯开始阶段的土塞发展影响不大,当土塞加速隆起后,压贯越深的情况土塞发展越迅速;在粘土中进行吸力沉贯时,API规范对最大容许吸力估算较为准确,但是需提供比API规范更大的沉贯吸力才能保持沉贯的进行,而且沉贯过程中土塞的高度大于由于简裙下插置换土体所带来的高度.     

复合加载条件下吸力式沉箱基础承载特性数值分析

吸力式沉箱基础的承载特性是海洋工程结构设施建造与设计中的一个关键问题。这种新型的深水海洋基础型式,通常承受竖向上拔荷载与水平荷载的共同作用,其工作性能与设计理论远远不能满足工程实践的需要。本文采用有限元分析方法对吸力式沉箱基础的极限承载特性进行数值计算。以大型通用有限元分析软件ABAQUS为平台,通过二次开发,数值实现了Swipe试验加载方法和固定位移比分析方法,针对不同的沉箱长径比、土的强度折减系数,探讨了沉箱基础在垂直上拔荷载和水平荷载单调联合作用下的极限承载力,通过对不同荷载组合的数值计算构造了复合加载条件下沉箱基础破坏包络面。     

粉土中吸力桶沉贯阻力与土塞失稳机理研究

针对粉土中吸力桶在吸力沉贯中的两个关键性问题——沉贯阻力和内部土体稳定性,在自行研制的试验平台上进行了一系列吸力桶沉贯模型试验。试验结果表明,粉土中吸力沉贯时,Andersen所提供的基于CPT锥尖强度的阻力计算公式能较好预测阻力发展趋势,但计算结果偏小;而修正的承载力公式预测结果在沉贯前期与实测值较吻合,沉贯后期预测偏大。吸力沉贯前期,贯入阻力随深度稳步增长,直到贯入深度达到某个临界值后,阻力增长缓慢甚至保持不变。桶内粉土在吸力作用下的失稳机理与黏土或砂土不同,在渗透力作用下表现为从土层表面开始的自上而下管涌或渗流侵蚀。沉贯后期,端部土体在较高水头差下发生失稳并向桶内流动,造成了桶内土体密度降低,端阻力与内壁摩阻力降低,总贯入阻力主要由外壁摩阻力提供。并结合有限元模拟对上述实验现象的内在机理进行了解释。     

黄河水下三角洲高浓度黏性泥沙流变特性及其影响因素

黏性泥沙在黄河水下三角洲广泛分布,其在外部载荷作用下易引发泥沙淤积、冲刷、海床流化等问题,对港口、航道、海底管线等工程设施构成巨大威胁。利用黄河水下三角洲埕岛海域所取海底表层沉积物,制备不同固结时间和不同含水率的高浓度黏性泥沙样品。采用R/S流变仪,对所制备高浓度黏性泥沙样品进行全剪切速率下的流变试验,分析黄河水下三角洲高浓度黏性泥沙流变特性及含水率和固结时间对流变特性的影响。结果表明,高浓度黏性泥沙在剪切荷载作用下流化失稳,发生相态转化;屈服应力在固结120 min后增加了35%;含水率50%以上高浓度黏性泥沙在高剪切速率下表现出剪切增稠行为,且随含水率增加剪切增稠行为越明显;Power模型适用于含水率大于50%的高浓度黏性泥沙在高剪切速率下的流变行为。本研究可为海底黏性泥沙运动过程数值模拟与海底重力流等灾害预测提供参考。     

吸力式沉箱基础长期水平荷载作用下承载特性试验研究

通过两组不同水平荷载作用下吸力式沉箱基础长期模型试验,对吸力式沉箱基础随时间的位移变化规律以及土压力分布规律进行了研究。试验结果表明:在长期模型试验中位移发展主要集中在试验前期,后期位移稳定需要更长时间,土体流变效应较为明显。土压力沿深度分布曲线呈抛物形状,表明沉箱基础在水平荷载作用下为转动模式,随时间增加被动区土压力变化呈增大趋势,主动区土压力呈减小趋势。土压力发展主要集中在试验前期,后期土压力变化相对较小,但土压力稳定所需时间较长,同时荷载值越大土压力稳定所需时间越长。     

离岸裙式吸力基础在砂土地基中沉贯性研究

吸力基础是海洋工程中新型的一种基础型式,广泛应用于海洋平台、海洋浮动式结构等,近年来,也被作为浅海离岸风力发电工程的基础。吸力基础易遭受较大的水平动力荷载和弯矩,从而可能产生较大水平位移和转角;同时,由于海床冲刷,会降低其承载能力。为克服这些不足,提出了一种新型吸力基础———裙式吸力基础,把分析传统吸力基础砂土中的沉贯方法,拓广到裙式吸力基础中,研究该基础型式在砂土中的可沉贯性以及所需的吸力;并与同情况下的传统吸力基础进行了比较,证明了所提出的裙式吸力基础具有较好的沉贯性能,具有工程实践推广价值。     

砂土中吸力式导管架基础沉贯试验研究

吸力式导管架基础具备高承载力、高施工效率、高环境友好度、低造价等特点,使用其作为海上风电底部支撑结构有利于产业的规模化发展,实现上述愿景的前提在于使筒型基础顺利安装以满足设计要求。基于此,在不同初始施加泵压下,对吸力式导管架的沉贯效率特征值、基础内外围渗流变化、筒裙端部土压力特点进行探究。通过抱桩器使吸力式导管架在吸力安装过程中仅具备竖向自由度,从而进行纯沉贯试验。结果表明：初始泵压2 kPa时沉贯效率特征值最高;沉贯过程中基础外围渗流水压小于基础内围渗流水压;筒裙外侧所受土压要大于筒壁内侧所受土压力。     

桶形基础沉贯室内模型试验研究

桶形基础采用负压沉贯法施工,其贯入阻力与压桩,打桩等施工方法显著不同。本文介绍了在粉土和粉质粘土地层中的一组模型试验情况,认为负压法施工可显著降低粉土的抗贯阻力,但在粉质粘土中减阻效果不明显。     

海上风电吸力基础在分层土中的沉贯特性研究综述

吸力基础与海洋工程大直径钢桩相比,具有成本低、安装周期短、对环境影响小、不受海况影响及可回收再利用等优点,近年来在海上风电工程中得到推广应用。吸力基础沉贯至海床预定位置,是其发挥承载力和确保服役稳定性的前提。海床地基土体常以分层土形式分布,且各层土体强度、压缩性和渗透性等存在显著差别,导致吸力基础吸力沉贯机理非常复杂。明确吸力基础在分层土中沉贯特性,有助于指导吸力基础在海上风电工程中的推广应用。对目前吸力基础在分层土中沉贯特性研究进行综述和总结,归纳了其沉贯机理研究进展,并对影响吸力基础在分层土中沉贯因素进行了分析;提出了分层土中吸力基础沉贯的研究方向和改进的沉贯方法。     

Large deformation finite element analysis of the installation of suction caisson in clay

The suction caisson (or called suction anchor) which is considered as a relatively new type of foundation of offshore structures, has been extensively studied and applied for offshore wind turbines and oil platforms. The installation of the suction caisson is of great importance in the design and construction because it can bring about several issues and further influence the performance of holding capacity in safety service. In this paper, large deformation finite element (FE) analyses are performed to model the installation of suction caisson (SC) by suction and jacking in normally consolidated clay. The penetration of the suction caisson is modeled using an axisymmetric FE approach with the help of the Arbitrary Lagrangian–Eulerian (ALE) formulation which can satisfactorily solve the large deformation problem. The undrained shear strength of the clay and elastic modulus are varied with depth of soil through the subroutine VUFIELD. The numerical results allow quantification of the penetration resistance and its dependence on the installation method. The centrifuge test and theoretical solution are used for the FE model validation. After the validation, the penetration resistance, the soil plug heave, and the caisson wall friction have been examined through the FE model. Based on the numerical results, it is shown that the ALE technique can simulate the entire suction caisson penetration without mesh distortion problem. The installation method can play an important role on the penetration resistance, namely, the suction installation reduces the penetration resistance significantly compared to the purely jacked installation. With a further study on the suction case, it is found that as the final applied suction pressure increases, the soil plug heave increases, while the penetration resistance reduces with increase of the final suction pressure. The effect of the friction of internal caisson walls has been also investigated and a conclusion is drawn that internal wall friction has a significant contribution to the penetration resistance and it can be implicitly represented by varying coefficient of internal wall friction. As for the penetration resistance, both jacked and suction installation have great dependency on the internal wall friction.     

Evaluation of pullout load capacity of suction caissons in sand using a three-dimensional displacement approach

An investigation was conducted to obtain analytical solutions for the pullout behavior of a suction caisson undergoing inclined loads in sand. The inclined load is transformed into an equivalent load system in which the vertical, horizontal, and moment loads are applied on the center of the lid of the suction caisson. The vertical and lateral stiffness coefficients along the skirt of the suction caisson in sands are presented using the new three-dimensional elastic solutions taking into account the nonhomogeneous and nonlinear properties of the sand. The vertical, lateral, and rocking stiffness coefficients on the base of the suction caisson are presented considering the solutions of a hollow rigid cylindrical punch acting on the surface of a soil. The yield, pullout, and failure for sands with the nonhomogeneous and nonlinear characteristics are taken into consideration. The effects of the load inclination, the loading depth, and the aspect ratio on the pullout load capacity of the suction caisson are presented. Behaviour of the suction caisson in sand prior to failure is clarified from the relationship between tensile load, displacement, and rotation and that between depth, vertical pressure, and lateral pressure.     

Characteristic Test Study on Bearing Capacity of Suction Caisson Foundation Under Vertical Load

Suction caisson foundations are often subjected to vertical uplift loads, but there are still no wide and spread engineering specifications on design and calculation method for uplift bearing capacity of suction caisson foundation.So it is important to establish an uplift failure criterion. In order to study the uplift bearing mechanism and failure mode of suction caisson foundation, a series of model tests were carried out considering the effects of aspect ratio,soil permeability and loading mode. Test results indicate that the residual negative pressure at the top of caisson is beneficial to enhance uplift bearing capacity. The smaller the permeability coefficient is, the higher the residual negative pressure will be. And the residual negative pressure is approximately equal to the water head that causes seepage in the caisson. When the load reaches the ultimate bearing capacity, both the top and bottom negative pressures are smaller than Su and both the top and bottom reverse bearing capacity factors are smaller than 1.0 in soft clay. Combined the uplift bearing characteristics of caisson in sandy soil and soft clay, the bearing capacity composition and the calculation method are proposed. It can provide a reference for the engineering design of suction caisson foundation under vertical load.     

混合土层吸力筒沉贯阻力算法研究及应用

为补充DNVGL-RP-C212规范关于混合土层内吸力筒沉贯阻力计算参数的不确定描述,基于长乐外海风电场多个吸力筒基础的沉贯负压监测成果,对黏土—砂混合土层内吸力筒沉贯阻力算法进行研究。提出了基于黏粒含量确定侧阻力修正系数kf的算法,引入桩基工程中基于静力触探试验（CPT）的fs计算桩侧剪切强度的经验算法,并对其进行修正,用于计算吸力筒的沉贯侧阻力。对两种算法的准确性进行了验证,对其可靠性进行比较,提出了以前者计算结果为准,后者计算结果作为校核依据的建议。     

Model tests on performance of offshore wind turbine with suction caisson foundation in sand

Abstract

The performance of steel caisson during and after installation with different penetration velocities in medium dense sand is presented. The applied jacking forces, the amount of formed soil heave and bearing capacity were measured in the model tests. The influence of penetration velocities on jacking forces, soil heave and bearing capacity were also discussed in detail. The results indicated that the jacking forces for caisson in medium dense sands were significantly affected by the penetration velocity. The larger the penetration velocity, the more soil flowed into the caisson cavity during installation. This will lead to larger inner shaft resistance and in turn more jacking forces required for the same penetration depth. The height of soil heave during installation increases with penetration velocity. The m value calculated by the ratio of the volumes of the soil heave to that of the penetrated caisson wall can be used to evaluate the soil heave. The larger the applied velocity, the larger the m value and larger bearing capacity of caisson after installation. The relationship between the m value and penetration velocity can be used to control the soil heave for a steel caisson with a wall thickness to external diameter ratio of 4.2% in medium dense sand by jacking method.     

Analytical and experimental studies on installation of a suction caisson with tampered tip in clay

Concrete suction caissons have been successfully used as breakwaters or seawalls in recent years. The relative large wall thickness-to-diameter ratio of a concrete caisson can lead to the formation of a full soil heave plug that may cause difficulties in the installation of concrete caisson in clay. One way to overcome this limitation is to use a tampered tip for the caisson wall. An analytical method is proposed in this article to calculate the minimum suction pressure required to penetrate a caisson and the maximum allowable suction pressure that can be applied to avoid too much soil heave plug during the installation of the suction caisson. Four model tests were conducted in normally consolidated clay to study the installation process of a concrete suction caisson with tampered tip and to verify the proposed analytical method. The height of the soil heave plug in the caisson with a tampered tip is observed to be about half of that in the caisson with a flat tip.     

Experimental studies on sand plug formation in suction caisson during extraction

A series of model tests were conducted on Perspex-made suction caissons in saturated dense marine sand to study the sand plug formation during extraction. Suction caissons were extracted by pullout loading or by pumping air into the suction caisson. Effects of the pullout rates, aspect ratios and loading ways (monotonic or sustained) on the pullout capacity, and plug formation were investigated. It was found that the ultimate pullout capacity of the suction caisson increases with increasing the pullout rate. The sand plug formation under the pullout loading is significantly influenced by the pullout rate and the loading way. When the suction caisson is extracted at a relatively slow rate, the general sand boiling through the sand plug along the inner caisson wall occurs. On the contrary, the local sand boiling will occur at the bottom of the suction caisson subjected to a rapid monotonic loading or a sustained loading. Test results of the suction caisson extracted by pumping air into the caisson show that the pressure in the suction caisson almost follows a linear relationship with the upward displacement. The maximum pressures for suction caissons with aspect ratios of 1.0 and 2.0 during extraction by pumping air into the caisson are 1.70 and 2.27 times the maximum suction required to penetrate the suction caisson into sand. It was found that the sand plug moves downward during extraction by pumping air into the caisson and the variation in the sand plug height is mainly caused by the outflow of the sand particles from the inside of the suction caisson to the outside. When the suction caisson model is extracted under the pullout rate of 2?mm/s (0.28?mm/s for the prototype), the hydraulic gradient along the suction caisson wall increases to the maximum value with increasing the penetration depth and then reduces to zero. On the contrary, when extracted under the pullout rate of 10?mm/s (1.4?mm/s for the prototype), the hydraulic gradient along the suction caisson wall increases with increasing the pullout displacement. When extracted by pumping air into the caisson, the hydraulic gradient reaches the critical value, and at the same time, the seepage failure occurs around the suction caisson tip.