Significant resistivity changes in the fault zone associated with the 1999 Chi-Chi earthquake, west-central Taiwan

The purpose of this paper is to demonstrate the possible influence of an earthquake on the resistivity distribution in a fault zone. We collected resistivity image profiles across a proposed fault trace prior to the 7.3 magnitude 1999 shallow earthquake in the Chi-Chi area of Taiwan. Significant positive resistivity anomalies were observed in the hanging wall after the earthquake. However, there were negligible resistivity changes in the footwall. From an examination of geoelectric phenomena and surface rupture in the fault zone, it is believed that geoelectric anomalies are associated with abrupt displacement along the active Chelungpu fault. This result indicates a potential for resistivity methods to provide a basis for the monitoring of an active fault.     

Tomographic image of crustal structures across the Chelungpu fault: Is the seismogenic layer structure- or depth-dependent?

In 1999, a large earthquake (M_w = 7.6) occurred along the Chelungpu fault in the fold-and-thrust belt of western Taiwan. To shed more light on the subsurface structures and the seismogenic layers, three-dimensional velocity structures were inverted by using the travel times of both P- and S-waves from 2391 aftershocks recorded by the Central Weather Bureau during the 15 months that followed. From tomography, a typical image of the large-scale thrusting structures in the upper crust across the Chelungpu fault was obtained. In general, high velocities beneath the Western Foothills and Central Ranges are separated from low velocities beneath the Coastal Plain by an east-dipping boundary that is roughly consistent with the Chelungpu fault on the surface. The contrast in velocity on either side of the Chelungpu fault is indicative of about a 7- to 9-km vertical offset in the upper crust. The relocated hypocenter for the Chi-Chi earthquake shifts by 2.2 km toward the northwest, and its focal depth decreases by 0.7 km. A plot of focal depths versus rock velocities where the aftershocks occurred shows earthquakes are more inclined to occur in rock with a velocity of around 5.6 km/s. This strongly suggests the seismogenic layer in the fold-and-thrust belt of Taiwan is more structure-dependent than depth-dependent.     

Imaging the ramp–décollement geometry of the Chelungpu fault using coseismic GPS displacements from the 1999 Chi-Chi, Taiwan earthquake

We use coseismic GPS data from the 1999 Chi-Chi, Taiwan earthquake to estimate the subsurface shape of the Chelungpu fault that ruptured during the earthquake. Studies prior to the earthquake suggest a ramp–décollement geometry for the Chelungpu fault, yet many finite source inversions using GPS and seismic data assume slip occurred on the down-dip extension of the Chelungpu ramp, rather than on a sub-horizontal décollement. We test whether slip occurred on the décollement or the down-dip extension of the ramp using well-established methods of inverting GPS data for geometry and slip on faults represented as elastic dislocations. We find that a significant portion of the coseismic slip did indeed occur on a sub-horizontal décollement located at 8 km depth. The slip on the décollement contributes 21% of the total modeled moment release. We estimate the fault geometry assuming several different models for the distribution of elastic properties in the earth: homogeneous, layered, and layered with lateral material contrast across the fault. It is shown, however, that heterogeneity has little influence on our estimated fault geometry. We also investigate several competing interpretations of deformation within the E/W trending rupture zone at the northern end of the 1999 ground ruptures. We demonstrate that the GPS data require a 22- to 35-km-long lateral ramp at the northern end, contradicting other investigations that propose deformation is concentrated within 10 km of the Chelungpu fault. Lastly, we propose a simple tectonic model for the development of the lateral ramp.     

Co-seismic displacements, folding and shortening structures along the Chelungpu surface rupture zone occurred during the 1999 Chi-Chi (Taiwan) earthquake

A nearly 100-km-long surface rupture zone, called Chelungpu surface rupture zone, occurred mostly along the pre-existing Chelungpu fault on the northwestern side of Taiwan, accompanying the 1999 Chi-Chi Ms 7.6 earthquake. The Chelungpu surface rupture zone can be divided into four segments based on the characteristics of co-seismic displacements, geometry of the surface ruptures and geological structures. These segments generally show a right-step en echelon form and strike NE–SW to N–S, and dip to the east with angles ranging from 50 to 85°. The co-seismic flexural-slip folding structures commonly occurred in or near the surface rupture zone from a few meters to a few hundreds of meters in width, which have an orientation in fold axes parallel or oblique to the surface rupture zone. The displacements measured in the southern three segments are approximately 1.0–3.0 m horizontally and 2.0–4.0 m vertically. The largest displacements were measured in the northern segment, 11.1 m horizontally and 7.5 m vertically, respectively. The amount of co-seismic horizontal shortening caused by flexural-slip folding and reverse faulting in the surface rupture zone is generally less than 3 m. It is evident that the co-seismic displacements of the surface rupture zone are a quantitative surface indicator of the faulting process in the earthquake source fault. The relations between the geometry and geomorphology of the surface rupture zone, dips of the co-seismic faulting planes and the striations on the main fault planes generated during the co-seismic displacement, show that the Chelungpu surface rupture zone is a reverse fault zone with a large left-lateral component.     

A study of the human-fatality rate in near-fault regions using the Victim Attribute Database

After the 1999 Chi-Chi earthquake, the Taiwanese government immediately issued new guidelines prohibiting the construction of structures for human occupancy within the Chelungpu fault zone. However, these guidelines were not based upon an in-depth hazard analysis of the near-fault regions. The positions of more than 80% of the 2,492 victims of the Chi-Chi earthquake were found by our research team. A Victim Attribute Database has been compiled that includes the GPS coordinates of the positioned victims as well as other attribute data associated with the victims. The human-fatality rates in the near-fault regions have been analyzed with regard to distances from the Chelungpu fault, the hanging-wall and footwall areas, as well as building type. The severity at the human-fatality rates in the near-fault regions is inversely proportional to distances from the causative fault, i.e., the closer the distance, the higher the human-fatality rate observed. The human-fatality rate for victims who lived in closer proximity to the hanging-wall areas is also significantly higher than those who lived in closer proximity to the footwall areas, especially in areas on either side of the fault and within 1,000 m of the fault surface trace. In terms of different building types, factors that include the capacity of the buildings to resistant strong shaking and the level of strong ground-motion greatly affected the human-fatality rates in the hanging-wall and footwall areas. Therefore simply prohibiting the construction of buildings within the active fault zone would be an insufficient method of reducing the number of potential victims; a nationwide effort should be undertaken to upgrade the capacity of buildings to resist strong shaking.     

Crustal structure of the Ruby Mountains and southern Carlin Trend region, Nevada, from magnetotelluric data

We have collected about 150 magnetotelluric (MT) soundings in northeastern Nevada in the region of the Ruby Mountains metamorphic core complex uplift and southern Carlin mineral trend, in an effort to illuminate controls on core complex evolution and deposition of world-class gold deposits. The region has experienced a broad range of tectonic events including several periods of compressional and extensional deformation, which have contributed to the total expression of electrical resistivity. Most of the soundings reside in three east–west profiles across increasing degrees of core uplift to the north (Bald Mountain, Harrison Pass, and Secret Pass latitudes). One short cross-line was also taken to assess an east–west structure to the north of the northern profile. Model resistivity cross-sections were derived from the MT data using a 2-D inversion algorithm, which damps departures of model parameters from an a priori structure. Geological interpretation of the resistivity combines previous seismic, potential field and isotope models, structural and petrological models for regional compression and extension, and detailed structural/stratigraphic interpretations incorporating drilling for petroleum and mineral exploration. To first order, the resistivity structure is one of a moderately conductive, Phanerozoic sedimentary section fundamentally disrupted by intrusion and uplift of resistive crystalline rocks. Late Devonian and early Mississippian shales of the Pilot and Chainman Formations together form an important conductive marker sequence in the stratigraphy and show pronounced increases in conductance (conductivity–thickness product) from east to west. These increases are attributed to graphitization caused by Elko–Sevier era compressional shear deformation and possibly by intrusive heating. The resistive crystalline central massifs adjoin the host stratigraphy across crustal-scale, steeply dipping fault zones. The zones provide pathways to the lower crust for heterogeneous, upper crustal induced, electric current flow. Resistive core complex crust appears steeply bounded under the middle of the neighboring grabens and not to deepen at a shallow angle to arbitrary distances to the west. The numerous crustal breaks imaged with MT may contribute to the low effective elastic thickness (T_e) estimated regionally for the Great Basin and exemplify the mid-crustal, steeply dipping slip zones in which major earthquakes nucleate. An east–west oriented conductor in the crystalline upper crust spans the East Humboldt Range and northern Ruby Mountains. The conductor may be related to nearby graphitic metasediments, with possible alteration by middle Tertiary magmatism. Lower crustal resistivity everywhere under the profiles is low and appears quasi one-dimensional. It is consistent with a low rock porosity (<1 vol.%) containing hypersaline brines and possible water-undersaturated crustal melts, residual to the mostly Miocene regional extension. The resistivity expression of the southern Carlin Trend (CT) in the Pinon Range is not a simple lineament but rather a family of structures attributed to Eocene intrusion, stratal deformation, and alteration/graphitization. Substantial reactivation or overprinting by core complex uplift or Basin–Range extensional events seems likely. We concur with others that the Carlin Trend may result in part from overlap of the large Eocene Northeast Nevada Volcanic Field with Precambrian–Paleozoic deep-water clastic source rocks thickening abruptly to the west of the Pinon Range, and projecting to the north–northwest.     

Fluid infiltration associated with seismic faulting: Examining chemical and mineralogical compositions of fault rocks from the active Chelungpu fault

In order to understand the fault zone architecture and mechanisms that caused the Chi-Chi earthquake, the Chelungpu drilling project was conducted during April 2000 through a collaborative project between Japan and Taiwan. In this study, chemical and mineralogical variations within the overall Chelungpu fault zone, including variations between less damaged host rocks, damaged zones, and fault cores caused by the Chi-Chi earthquake were examined. Slopes of TiO₂ immobile isocons were consistently > 1 for analyses comparing host rocks with rocks from damaged zones or with gouges from fault cores, indicating that volume loss occurred in damaged zones and the fault cores. These results strongly imply that pervasive fluid infiltration occurred within the fault zone. Volume loss within the damaged zone and fault core is interpreted to result from a two-stage process involving: (i) coseismic mechanical wearing and/or dissolution in the fault core, and (ii) fluid infiltration within the fault zone during postseismic and interseismic periods along cracks caused by seismic failure. Semi-quantitative XRD analysis indicates that the kaolinite content consistently increases from the less damaged host rocks to the damaged zone and gouges in each fault core. Mineralogic changes indicate that pervasive acidic fluid infiltration occurred within the fault zones and reacted with the feldspars or muscovite to form kaolinite. Enrichment of kaolinite and illite found in the fault zones of southern drilling site could play some role on the slipping behavior of the southern part of the Chelungpu fault. Greater volume loss in the fault core may have resulted from moderate permeability, combined with the very fine grain nature of pulverized material in the fault core, which enhanced chemical reactions including transformation of feldspars and muscovite to clay minerals. The study results indicate that pervasive fluid infiltration occurred and changed the mineralogical and chemical architecture of fault zones caused by the cyclic earthquakes.     

Characterization of slip zone associated with the 1999 Taiwan Chi-Chi earthquake: X-ray CT image analyses and microstructural observations of the Taiwan Chelungpu fault

To characterize the fault-related rocks within the Chelungpu fault, we performed X-ray computed tomography (CT) image analyses and microstructural observations of Hole B core samples from the Taiwan Chelungpu-fault Drilling Project. We identified the slip zone associated with the 1999 Chi-Chi earthquake, within the black gouge zone in the shallowest major fault zone, by comparison with previous reports. The slip zone was characterized by low CT number, cataclastic (or ultracataclastic) texture, and high possibility to have experienced a mechanically fluidized state. Taking these characteristics and previous reports of frictional heating in the slip zone into consideration, we suggested that thermal pressurization was the most likely dynamic weakening mechanism during the earthquake.     

Magnetotelluric images of the crustal structure of Chyulu Hills volcanic field, Kenya

Electromagnetic experiments were conducted in 1995 as part of a multidisciplinary research project to investigate the deep structure of the Chyulu Hills volcanic chain on the eastern flank of the Kenya Rift in East Africa. Transient electromagnetic (TEM) and broadband (120–0.0001 Hz) magnetotelluric (MT) soundings were made at eight stations along a seismic survey line and the data were processed using standard techniques. The TEM data provided effective correction for static shifts in MT data. The MT data were inverted for the structure in the upper 20 km of the crust using a 2-D inversion scheme and a variety of starting models. The resulting 2-D models show interesting features but the wide spacing between the MT stations limited model resolution to a large extent. These models suggest that there are significant differences in the physical state of the crust between the northern and southern parts of the Chyulu Hills volcanic field. North of the Chyulu Hills, the resistivity structure consists of a 10–12-km-thick resistive (up to 4000 Ω m) upper crustal layer, ca. 10-km-thick mid-crustal layer of moderate resistivity (50 Ω m), and a conductive substratum. The resistive upper crustal unit is considerably thinner over the main ridge (where it is ca. 2 km thick) and further south (where it may be up to 5 km thick). Below this cover unit, steep zones of low resistivity (0.01–10 Ω m) occur underneath the main ridge and at its NW and SE margins (near survey positions 100 and 150–210 km on seismic line F of Novak et al. [Novak, O., Prodehl, C., Jacob, A.W.B., Okoth, W., 1997. Crustal structure of the southern flank of the Kenya Rift deduced from wide-angle P-wave data. In: Fuchs, K., Altherr, R., Muller, B., Prodehl, C. (Eds.), Structure and Dynamic Processes in the Lithosphere of the Afro-Arabian Rift System. Tectonophysics, vol. 278, 171–186]). These conductors appear to be best developed in upper crustal (1–8 km) and middle crustal (9–18 km) zones in the areas affected by volcanism. The low-resistivity anomalies are interpreted as possible magmatic features and may be related to the low-velocity zones recently detected at greater depth in the same geographic locations. The MT results, thus, provide a necessary upper crustal constraint on the anomalous zone in Chyulu Hills, and we suggest that MT is a logical compliment to seismics for the exploration of the deep crust in this volcanic-covered basement terrain. A detailed 3-D field study is recommended to gain a better understanding of the deep structure of the volcanic field.     

Deep structure of the Longling–Ruili fault underneath Ruili basin near the eastern Himalayan syntaxis: insights from magnetotelluric imaging

Magnetotelluric (MT) geophysical profiling has been applied to the determination of the deep structure of the Longling–Ruili fault (LRF), part of a convergent strike-slip fault system, underneath thick Caenozoic cover in Ruili basin in southwestern Yunnan, China. The recorded MT data have been inverted using a two-dimensional (2-D) nonlinear conjugate gradients scheme with a variety of smooth starting models, and the resulting models show common subsurface conductivity structures that are deemed geological significant. The models show the presence of a conductive (5–60 Ω m) cover sequence that is thickest (1–1.5 km) in the centre of the basin and rapidly pinches out towards the margins. A half-graben structure is interpreted for the Ruili basin. This is underlain by about 7–10 km thick upper crustal layer of high resistivity (>200–4000 Ω m) that is dissected by steep faults, which we interpret to flatten at depth and root into an underlying mid-crustal conductive layer at about 10 km depth. The mid-crustal layer does not appear to have been severely affected by faulting; we interpret it as a zone of partial melt or intracrustal detachment. The MT models suggest SE directed thrusting of basement rocks in the area. The Longling–Ruili fault is interpreted as a NW-dipping feature bounding one of the identified upper crustal fragments underneath Ruili city. We suggest that MT imaging is a potent tool for deep subsurface mapping in this terrain.     

Response changes of some wells in the mainland subsurface fluid monitoring network of China, due to the September 21, 1999, Ms7.6 Chi-Chi Earthquake

About 60 hydrologic changes in response to the Chi-Chi earthquake with Ms7.6 on September 21, 1999, occurred in 52 wells, including groundwater level, temperature, discharge rate, well pressure and radon, etc., in the subsurface fluid monitoring network. These response changes were mainly co-seismic, but some pre- and post-earthquake changes occurred mainly within 5 days before and after the Chi-Chi earthquake. The response changes of different wells clustering in different tectonic areas showed different features. These changes are distributed in five areas named as A, B, C, D and E. The response changes in A area with short hypo-central distance (less than 550 km) were mainly pre-earthquake changes occurring more than 5 days before the event. Those in area B (in Huanan tectonic block) and C (in Huabei tectonic block) were mainly co-seismic changes. The hypo-central distance is about 1100–1280 and 800–1160 km, respectively. These changes were high-frequency water-level oscillations induced by seismic waves and accompanied by prominent and permanent water-level jumps and drops. There are also some post-seismic changes including discharge rate and water radon and well pressure changes in area C. Those in area D in the Yanshan tectonic block were mainly co-seismic and post-seismic changes including water level, water temperature, and water radon concentration, etc., showing prominent and permanent water-level jumps and drops and rising concentrations of water radon. The hypo-central distance is about 1750–2060 km. Those in Area E were mainly co-seismic changes showing prominent and permanent water-level jump. The hypo-central distance is about 1810–2120 km. Three moderate earthquakes occurred in area D and one strong earthquake occurred in area E 4 months after the Chi-Chi earthquake. The different features of the response changes might be caused by the changes of local hydrologic conditions (like permeability) induced by seismic waves. On the other hand, these response changes might indicate the near-critical conditions in the area where the response changes clustered. Such changes might be understood by the crustal buckling hypothesis. It is thought that the response changes might be a kind of precursor that implies elevated earthquake risk in the region.     

Magnetotelluric Constraints on the Occurrence of Lower Crustal Earthquakes in the Intra-plate Setting of Central Indian Tectonic Zone

Lower crustal earthquake occurrence in the Central Indian Tectonic Zone(CITZ) of the Indian sub-continent was investigated using magnetotelluric(MT) data. MT models across the CITZ, including the new resistivity model across the 1938 Satpura lower crustal earthquake epicenter, show low resistive(80 ?m) mid-lower crust and infer small volume(1 vol%) of aqueous fluids existing in most part of lower crust. This in conjunction with xenoliths and other geophysical data supports a predominant brittle/semi-brittle lower crustal rheology. However, the local deep crustal zones with higher fluid content of 2.2%–6.5% which have been mapped imply high pore pressure conditions. The observation above and the significant strain rate in the region provide favorable conditions(strong/moderate rock strength, moderate temperature, high pore pressure and high strain rate) for brittle failure in the lower crust. It can be inferred that the fluid-rich pockets in the mid-lower crust might have catalyzed earthquake generation by acting as the source of local stress(fluid pressure), which together with the regional stress produced critical seismogenic stress conditions. Alternatively, fluids reduce the shear strength of the rocks to favor tectonic stress concentration that can be transferred to seismogenic faults to trigger earthquakes.     

Magnetotelluric investigations for imaging electrical structure of Garhwal Himalayan corridor,Uttarakhand, India

Magnetotelluric investigations have been carried out in the Garhwal Himalayan corridor to delineate the electrical structure of the crust along a profile extending from Indo-Gangetic Plain to Higher Himalayan region in Uttarakhand, India. The profile passing through major Himalayan thrusts: Himalayan Frontal Thrust (HFF), Main Boundary Thrust (MBT) and Main Central Thrust (MCT), is nearly perpendicular to the regional geological strike. Data processing and impedance analysis indicate that out of 44 stations MT data recorded, only 27 stations data show in general, the validity of 2D assumption. The average geoelectric strike, N70°W, was estimated for the profile using tensor decomposition. 2D smooth geoelectrical model has been presented, which provides the electrical image of the shallow and deeper crustal structure. The major features of the model are (i) a low resistivity (<50Ωm), shallow feature interpreted as sediments of Siwalik and Indo-Gangetic Plain, (ii) highly resistive (> 1000Ωm) zone below the sediments at a depth of 6 km, interpreted as the top surface of the Indian plate, (iii) a low resistivity (< 10Ωm) below the depth of 6 km near MCT zone coincides with the intense micro-seismic activity in the region. The zone is interpreted as the partial melting or fluid phase at mid crustal depth. Sensitivity test indicates that the major features of the geoelectrical model are relevant and desired by the MT data.     

The Investigation Results of the April 12, 2014, <Emphasis Type="Italic">M</Emphasis> = 4.5 Primorye Earthquake (Far Eastern Russia)

Primorye is a region with quite moderate shallow seismicity which has been insufficiently investigated so far in this respect. Based on the obtained instrumental data of regional seismic networks and macroseismic data collected in southwestern Primorye on the crustal earthquake with M = 4.5 occurred on April 12, 2014, we have first succeeded in determining the hypocenter parameters and the focal mechanism of the mainshock of this shallow earthquake and estimating the hypocenter parameters of the following aftershock.     

Seismic imaging,crustal stress and GPS data analyses: Implications for the generation of the 2008 Wenchuan Earthquake (M7.9), China

Seismic imaging together with global positioning system (GPS) and crustal stress data analyses show that the Mw7.9 2008 Wenchuan earthquake occurred within a distinct area of high crustal stress (～ 17.5 MPa) and high Poisson's ratio (7–10%) anomalies centered on the Longmen-Shan (Shan means Mountain in Chinese) tectonic fault belt. Low P-wave and S-wave velocities in the southwest (SW) segment contrast with high-velocity anomalies in the central portion (CP) and northeast (NE) segment within the uppermost ～ 15 km depths along the tectonic fault belt, though a presumably ductile zone with low-velocity anomalies separates the CP and NE segment. The rupture initiated near the southwestern end of the CP at a zone of high Poisson's ratio (σ) which extends down into the lower crust. These low-velocity and high-σ anomalies immediately below the source hypocenter, together with the high crustal stress, indicate the presence of high-pressure fluids from the lower crust, which might have reduced the mechanical strength of the fractured rock matrix and triggered the earthquake. Our study suggests that the structural heterogeneity and high crustal stress played an important role in the nucleation of the Wenchuan earthquake and its rupture process.     

Implications for the lithospheric structure of Cambay rift zone,western India:Inferences from a magnetotelluric study

Broad-band and long-period magnetotelluric(MT) data were acquired along an east-west trending traverse of nearly 200 km across the Kachchh,Cambay rift basins,and Aravalli-Delhi fold belt(ADFB),western India.The regional strike analysis of MT data indicated an approximate N59°E geoelectric strike direction under the traverse and it is in fair agreement with the predominant geological strike in the study area.The decomposed transverse electric(TE)-and transverse magnetic(TM)-data modes were inverted using a nonlinear conjugate gradient algorithm to image the electrical lithospheric structure across the Cambay rift basin and its surrounding regions.These studies show a thick(～1-5 km) layer of conductive Tertiary-Mesozoic sediments beneath the Kachchh and Cambay rift basins.The resistive blocks indicate presence of basic/ultrabasic volcanic intrusives,depleted mantle lithosphere,and different Precambrian structural units.The crustal conductor delineated within the ADFB indicates the presence of fluids within the fault zones,sulfide mineralization within polyphase metamorphic rocks,and/or Aravalli-Delhi sediments/metasediments.The observed conductive anomalies beneath the Cambay rift basin indicate the presence of basaltic underplating,volatile(CO_2,H_2 O) enriched melts and channelization of melt fractions/fluids into crustal depths that occurred due to plume-lithosphere interactions.The variations in electrical resistivity observed across the profile indicate that the impact of Reunion plume on lithospheric structures of the Cambay rift basin is more dominant at western continental margin of India(WCMI) and thus support the hypothesis proposed by Campbell Griffiths about the plume-lithosphere interactions.     

Regional moment tensor uncertainty due to mismodeling of the crust

The retrieval of earthquake moment tensor (MT) requires the response of the medium, in which seismic waves travel from the hypocenter to the stations, to be known. In inverting long-period (LP) seismic data (teleseismic and LP regional records), a gross earth model is sufficient; with decreasing periods, a more detailed model is needed. This is the case when waveforms of weak earthquakes at regional distances are to be inverted. Regional moment tensors (RMTs) of mostly Mediterranean earthquakes are determined on a routine basis by the Swiss Seismological Survey (SED) by using averaged models of the earth's crust. By inverting broad-band records of the M_w=4.8 earthquake near Udine, N Italy, on Feb. 14, 2002, we tested the sensitivity of the MT solution with respect to possible errors in the earth model used and in the location of the hypocenter depth. We perturbed the P and S velocities and the thickness in the 1-D earth model in the range from 3% to 30% of the parameter values and constructed estimates of confidence regions of the MT and error bars of the source time function (STF) and scalar moment in three frequency bands. Similarly, these error characteristics were determined assuming a mislocation in the hypocenter depth. We found that, in the band of periods from 25 to 50 s, the mechanism is resolved well (at the confidence level 95% at least) up to an earth model uncertainty of 30%, in the passband 10–25 s up to about 10%, but it is undetermined completely at periods of 5–10 s. An error in hypocenter depth of as much as double the value reported by the location procedure does not destroy the resolution of the mechanism at periods above 10 s. In the RMT catalog of the SED, earthquakes of M_w greater than about 3.5 are processed at periods above 30 s; thus, the solutions for these events are robust with respect to a possible uncertainty in the earth model used. Mechanisms of weaker earthquakes, retrieved from short periods, should be interpreted with caution.     

Relation between electrical resistivity and earthquake generation in the crust of West Anatolia, Turkey

In this paper, we present a relation between the earthquake occurrence and electric resistivity structures in the crust, in West Anatolia and the Thrace region of Turkey. The relationship between magnetotelluric georesistivity models and crustal earthquakes in West Anatolia, during a period from 1900 to 2000, is investigated. It is found that most of the large crustal earthquakes occurred in and around the areas of the highest electrical resistivity in the upper crust, although rare small magnitude earthquakes are observed in some parts of the conductive lower crust in West Anatolian extensional terrain. The high-resistivity zones may represent rocks that are probably mechanically strong enough to permit sufficient stress to accumulate for earthquakes to occur in western Anatolia and the Thrace region. However, some recent studies state that the generation of a large earthquake is not only a pure mechanical process, but is closely related to fluid existence. We also reviewed recent world-wide researches including results from the Anatolian data for the first time and discussed all general findings in combination. Our findings show that the boundary between the resistive upper crust and the conductive lower crust correlates well with the cutout depth of the seismicity in West Anatolia and Thrace. This boundary is also attributed to the fluid bearing brittle–ductile transition zone in world literature. Fluid migration from the conductive lower crust to the resistive upper crust may contribute the seismicity in resistive zones. Alternatively, the upper–lower crust boundary may act as a stress concentrator and fluids may help to release strain energy in brittle parts of lower crust, by small magnitude earthquakes, whereas they may help in focusing strain in mechanically strong and electrically resistive zones for large earthquakes to occur.     

青藏高原东北缘海原-六盘山断裂带现今地壳应力环境的数值分析

海原-六盘山断裂是青藏高原东北缘的大型边界断裂带,是中国大陆典型的地震危险区。地壳构造加载特征的定量研究有助于分析区域孕震环境,参考青藏高原东北缘GPS形变和岩石圈精细结构等资料,本文建立海原-六盘山断裂带周缘的三维岩石圈分层模型,分析现今构造加载作用下区域地壳形变和应力演化特征。数值计算结果显示:青藏高原东北缘现今处于以北东-南西向的水平挤压为主导和北西-南东向的水平引张的变形特征。青藏高原东北缘中-下地壳流变性质影响上覆脆性地壳应力环境,中地壳较低粘滞系数对应的模型地壳应力计算值与研究区实际地壳应力场相近。海原断裂中-西段构造加载作用显著,具有相对较高的库仑应力积累和最大剪应力分布;而六盘山断裂周缘地壳应力和最大剪应力小于海原断裂带。构造应力积累的空间分布差异说明六盘山断裂具有较弱的构造孕震环境,而研究区走滑型断裂的孕震加载作用显著。尽管六盘山处于较低的应力状态,但仍不能轻易忽视其长期存在的强震空区所暗示的发震潜力。     

Detailed surface co-seismic displacement of the 1999 Chi-Chi earthquake in western Taiwan and implication of fault geometry in the shallow subsurface

The northern segment of the Chelungpu Fault shows an unusually large co-seismic displacement from the event of the Mw 7.6 Chi-Chi earthquake in western Taiwan. Part of the northern segment near the Fengyuan City provides an excellent opportunity for characterizing active thrust-related structures due to a dense geodetic-benchmark network. We reproduced co-seismic deformation patterns of a small segment of this Chelungpu Fault using 924 geodetic benchmarks. According to the estimated displacement vectors, we identified secondary deformations, such as local rigid-block rotation and significant shortening within the hanging wall. The data set also allows us to determine accurately a 3D model of the thrust fault geometry in the shallow subsurface by assuming simple relations between the fault slip, and the horizontal and vertical displacements at the surface. The predicted thrust geometry is in good agreement with borehole data derived from two drilling sites close to the study area. The successful prediction supports our assumptions of rigid displacement and control of displacement in the hanging wall by the fault geometry being useful first approximations.