Dynamic Installation Behaviors of A New Hybrid Plate Anchor in Layered Marine Clay

China Ocean Engineering - Layered soil profiles create challenges for foundation installation and detrimentally affect the foundation performance. This research explored the free-fall penetration...     

Effect of Cyclic Loading Frequency on Undrained Behaviors of Undisturbed Marine Clay

Based on a series of cyclic triaxial tests, the effect of cyclic frequency on the undrained behaviors of undisturbed marine clay is investigated. For a given dynamic stress ratio, the accumulated pore water pressure and dynamic strain increase with the number of cycles. There exists a threshold value for beth the accumulated pore water pressure and dynamic strain, below which the effect of cyclic frequency is very small, but above which the accumulated pore water pressure and dynamic strain increase intensely with the decrease of cyclic frequency for a given number of cycles. The dynamic strength increases with the increase of cyclic frequency, whereas the effect of cyclic frequency on it gradually diminishes to zero when the number of cycles is large enough, and the dynamic strengths at different frequencies tend to the same limiting minimum dynamic strength. The test results demonstrate that the reasons for the frequency effect on the undrained soil behaviors are beth the creep effect induced by the loading rate and the decrease of sample effective confining pressure caused by the accumulated pore water pressure.     

Field Evaluation of Undrained Shear Strength from Piezocone Penetration Tests in Soft Marine Clay

The use of the piezocone penetration test (CPTU) in a geotechnical site investigation offers direct field measurement on stratigraphy and soil behavior. Compared with some traditional investigation methods, such as drilling, sampling and field inspecting method or laboratory test procedures, CPTU can greatly accelerate the field work and hereby reduce corresponding operation cost. The undrained shear strength is a key parameter in estimation of the stability of natural slopes and deformation of embankments in soft clays. This paper provides the measurements of in situ CPTU, field vane testing and laboratory undrained triaxial testing of Lianyungang marine clay in Jiangsu province of China. Based on the literature review of previous interpretation methods, this paper presents a comparison of field vane testing measurements to CPTU interpretation results. The undrained shear strength values from both the field vane tests and cone penetration resistances are lowest at the mid-depths of the marine clay layers, and the excess pore water pressures are highest at the mid-depths of the marine clay layers, indicating that the marine clay layer is underconsolidated.     

Pullout Capacity of Horizontally Loaded Suction Anchor Installed in Silty Sand

Current floating structures require more reliable and higher anchoring capacities because of their increased size. A suction anchor is one of the most popular anchors for a floating system. In this study, the behavior of a suction anchor installed in cohesionless soil was investigated when the anchor was subjected to mainly a horizontal load. Three-dimensional finite element numerical analyses were carried out using ABAQUS, and three centrifuge tests were performed to calibrate the numerical analyses. A parametric study with different dimensions and loading points for the suction anchor was conducted. The horizontal capacity of the suction anchor was estimated, and the soil reaction distribution was analyzed when the load was applied at the optimal point. Based on the results, an analytical equation for calculating the horizontal capacity of a suction anchor was proposed that can be easily adopted for design.     

Sulphate Attack in Lime-Treated Marine Clay

The use of lime to improve the properties of soft clays is not new. Recently the deep lime mixing technique has been extended to coastal regions for improving the behavior of weak marine clays. But lime treatment technique should be approached carefully for clay containing a high percentage of sodium sulphate. The presence of sulphate in lime-treated clays may result in high swelling due to the formation of the expansive mineral, ettringite. A limited study of lime-treated marine clays has shown a need to further explore the formation of ettringite and its stability with time. In this article, a laboratory investigation was carried out to examine the influence of sodium and calcium sulphates on the behavior of lime column treated marine clay. Scanning electron microscopy (SEM) was used to identify the formation of various reaction products, including ettringite. Test results indicate that the formation of ettringite in the lime-sodium sulphate-clay system adversely affects the engineering behavior of the marine clay, whereas the addition of calcium sulphate significantly improves the engineering characteristics of the soil.     

Sulphate Attack in Lime-Treated Marine Clay

ABSTRACT

The use of lime to improve the properties of soft clays is not new. Recently the deep lime mixing technique has been extended to coastal regions for improving the behavior of weak marine clays. But lime treatment technique should be approached carefully for clay containing a high percentage of sodium sulphate. The presence of sulphate in lime-treated clays may result in high swelling due to the formation of the expansive mineral, ettringite. A limited study of lime-treated marine clays has shown a need to further explore the formation of ettringite and its stability with time. In this article, a laboratory investigation was carried out to examine the influence of sodium and calcium sulphates on the behavior of lime column treated marine clay. Scanning electron microscopy (SEM) was used to identify the formation of various reaction products, including ettringite. Test results indicate that the formation of ettringite in the lime-sodium sulphate-clay system adversely affects the engineering behavior of the marine clay, whereas the addition of calcium sulphate significantly improves the engineering characteristics of the soil.     

海上吸力锚负压下沉渗流场的特性分析

采用8结点等参元的有限元方法，对海上吸力锚负压沉贯过程中锚体周围土体的渗流场进行了数值计算与分析，并给出了渗流场相关要素的计算方法，如水头、等势线、渗流力、渗流速度和渗流量等。通过对实例的分析，计算结果和结论令人满意，为吸力锚的设计等现实应用提供了依据。     

Time-Dependent Deformation Behavior of Jiangsu Marine Clay

In this article, the mechanical behavior of a Jiangsu marine clay was investigated by drained triaxial tests, traixial rheological tests, and one-dimensional compression and swelling tests. A visco-plastic model, the Bingham model combining two yield surfaces model, was proposed to describe the time-dependent deformation behaviors of the marine clay. The governing equation of Biot's consolidation theory for the visco-plastic soil is solved using a finite element code which incorporates the visco-plastic model. Using the finite element method, settlements of a typical embankment on the Lianxu expressway in China are calculated. Settlement calculations using the visco-plastic model are in agreement with the measured settlements in the field. The results demonstrate that the visco-plastic model is appropriate for calculating the visco-plastic deformations of Jiangsu marine clay. Theoretical and experimental studies show that the visco-plastic deformation of Jiangsu marine clay is substantial.     

Strengthening of Soft Marine Clay Using Bioencapsulation

Dredged or excavated soft marine clay can be improved by mixing it with cement or lime. However, these treatments are usually expensive. It is shown in this paper that soft marine clay can be strengthened through a bioencapsulation method in which the shear strength of clay aggregates can be substantially increased after the aggregates are treated with urease-producing bacteria, calcium chloride, and urea. We found that the bioencapsulation had increased the unconfined compressive strength of marine clay aggregates with a size of 5 mm from almost zero to more than 2 MPa. The strength of the bioencapsulated clay aggregates decreases with the increase in the size of the aggregate when the size is greater than 5 mm.     

Secondary Compression Features of Jiangsu Soft Marine Clay

The results of one-dimensional compression tests conducted on undisturbed specimens of Jiangsu soft marine clay is presented. Because of its high in situ void ratios and natural water content, Jiangsu soft marine clay displays high values of both the virgin compression index, C_c, and the secondary compression coefficient, C_α. The laboratory data indicates that the value of the ratio C_α/C_c for Jiangsu soft marine clay is constant. However, neither C_α nor C_c are constant: they both depend upon the natural water content (or void ratio) and thus are also dependent on the deformation (or compression) of Jiangsu soft marine clay. Settlement analyses show that the secondary settlement of Jiangsu soft marine clay is a significant component of the field settlement. The concept of a constant value for C_α/C_c is used to predict the secondary settlement of a surcharged embankment founded upon Jiangsu soft marine clay. The predictions are in agreement with the limited post-construction field measurements of the embankment settlement.     

Penetration Resistance of Skirt-Tip with Rough Base for Suction Caissons in Clay

China Ocean Engineering - Suction caissons can readily penetrate into the seabed under the combination of the self-weight and suction resulted from the encased water being increasingly pumped out....     

Penetration Depth of Torpedo Anchor in Two-Layered Cohesive Soil Bed by Free Fall

The penetration depth of torpedo anchor in two-layered soil bed was experimentally investigated. A total of 177 experimental data were obtained in laboratory by varying the undrained shear strength of the two-layered soil and the thickness of the top soil layer. The geometric parameters of the anchor and the soil properties (the liquid limit, plastic limit, specific gravity, undrained shear strength, density, and water content) were measured. Based on the energy analysis and present test data, an empirical formula to predict the penetration depth of torpedo anchor in two-layered soil bed was proposed. The proposed formula was extensively validated by laboratory and field data of previous researchers. The results were in good agreement with those obtained for two-layered and single-layered soil bed. Finally, a sensitivity analysis on the parameters in the formula was performed.     

Dynamic Behaviors of A Marine Riser Under Two Different Frequency Parametric Excitations

The marine risers are often subjected to parametric excitations from the fluctuation top tension. The top tension on the riser may fluctuate with multiple frequencies caused by irregular waves. In this paper, the influence between different frequency components in the top tension on the riser system is theoretically simulated and analyzed. With the Euler-Bernoulli beam theory, a dynamic model for the vibrations of the riser is established. The top tension is set as fluctuating with time and it has two different frequencies. The influences from the fluctuation amplitudes, circular frequencies and phase angles of these frequency components on the riser system are analyzed in detail. When these two frequencies are fluctuating in the stable regions, the riser system may become unstable because ω_1+ω_2≈2Ωn. The fluctuation amplitudes of these frequencies have little effect on the components of the vibration frequencies of the riser. For different phase angles, the stability and dynamic behaviors of the riser would be different.     

Degradation in Cemented Marine Clay Subjected to Cyclic Compressive Loading

The influence of cyclic loading on the strength and deformation behavior of cemented marine clay has been studied. This marine clay is of recent Pleistocene origin and deposited in a shallow water marine environment. Open pits were dug in sheeted enclosures and from these pits, undisturbed samples were taken for strength testing. A series of standard triaxial shear tests and stress controlled one-way cyclic load tests were conducted at consolidation stress ranges below and above the preconsolidation pressure. For the stress levels below the preconsolidation pressure, the cyclic loading has brought about the collapse of the cementation bond through an increase in strains, and at higher pressure ranges, the soil behaves like typical soft clay. This experiment studied the rate of development of strain and pore water pressure and shows that rate is a function of number of cycles, applied stress, and stress history. In addition, soil degradation during cyclic loading is studied in terms of Degradation Index. Attempt has been made to predict stain, pore water pressure, and degradation index through an empirical model.     

Earth Pressure on Caissons in Marine Clay Under Cyclic Loading

Coastal protection is proposed to be made out of a contiguous caisson type of wall. These caissons can be designed to resist both lateral static and cyclic loading. With adequate depth of embedment, the walls can be designed to offer significant lateral passive resistance to counteract the lateral static and cyclic loading arising out of wave action. This article describes a set of laboratory tests on model caissons embedded into soft marine clay with different embedment depths. Specially designed earth pressure cells are embedded into the caisson at different depths. A pneumatic system was used to apply lateral static and cyclic loading. Test beds were prepared conforming to soft clay conditions in a test tank of appropriate size. The test results reveal that with this type of arrangement the variation in earth pressure with depth can be conveniently established. The earth pressure developed is related to the lateral load applied. The depth at which the maximum earth pressure occurs is same for both static and cyclic loading. Further, under cyclic loading there is no failure encountered even under cyclic loading level corresponding to 0.9 times the ultimate static lateral capacity.     

Effects of Degrees of Motion Freedom on Free-Fall of A Sphere in Fluid

Free-fall of a sphere in fluid is investigated at a Galileo number of 204 by direct numerical simulations (DNS). We mainly focus on the effects of different degrees-of-freedom (DOFs) of the sphere motion during free-fall. The characteristics of free-fall are compared with those of flow past a fixed sphere. Additional numerical tests are conducted with constraints placed on the translational or rotational DOFs of the sphere motion to analyze different DOFs of sphere motion. The transverse motion contributes significantly to the characteristics of free-fall; it results in the retardation of the vortex shedding, leading to the decrease of the Strouhal number. In addition, the transversal sphere motion exhibits the tendency to promote the sphere rotation. On the contrary, the effects of the sphere rotation and vertical oscillations during free-fall are negligible.     

Estimation of Uplift Capacity of Rapidly Loaded Plate Anchors in Soft Clay

Plate anchors are extensively used in civil engineering constructions as they provide an economical alternative to gravity and other embedded anchors. The rate of loading is one of the important factors that affects the magnitude of soil resistance as well as soil suction force. This article outlines the effect of pullout rate on uplift behavior of plate anchors (70 mm diameter) buried in soft saturated clay by varying the pullout rate from 1.4 mm/min to 21.0 mm/min. The variation of breakout force and suction force with embedment depth and rate of pull are presented. A correlation between the rate of increase of undrained strength of clay and anchor capacity with rate of strain has been established. Finally an empirical equation has been proposed that includes the rate of pull in the estimation of breakout capacity of anchors.     

Estimation of Uplift Capacity of Rapidly Loaded Plate Anchors in Soft Clay

Plate anchors are extensively used in civil engineering constructions as they provide an economical alternative to gravity and other embedded anchors. The rate of loading is one of the important factors that affects the magnitude of soil resistance as well as soil suction force. This article outlines the effect of pullout rate on uplift behavior of plate anchors (70 mm diameter) buried in soft saturated clay by varying the pullout rate from 1.4 mm/min to 21.0 mm/min. The variation of breakout force and suction force with embedment depth and rate of pull are presented. A correlation between the rate of increase of undrained strength of clay and anchor capacity with rate of strain has been established. Finally an empirical equation has been proposed that includes the rate of pull in the estimation of breakout capacity of anchors.     

Assessment of Unconfined Compressive Strength of Cement Stabilized Marine Clay

Two aspects of deep mixing method, the difference relating strength gain in dry jet mixing (DJM, reagent powder introduced into the ground) and cement deep mixing (CDM, reagent slurry introduced into the ground), and prediction of unconfined compressive strength of cement stabilized marine clay, are discussed in this paper. The first part of this paper concentrates on the difference between DJM and CDM on strength gain, and suggests a guideline for DJM and CDM selection. An indicator in terms of water content ratio, which is defined as the ratio of water content to the liquid limit of the soil, is presented by statistical analysis from the laboratory and field test data as a guideline for the selection of DJM or CDM. Based on the laboratory test data, a mathematical model relating strength gain of cement stabilized marine clay to related variables is developed. A new simple index designated as total water-cement ratio, which is defined as the ratio of water weight in the soil-cement to the weight of cement in dry state, is proposed for interpretation of test data of soil-cement. The proposed method is then verified with available test data published by other different researchers.     

Behavior of a Large Cylinder in Free-Fall Through Water

This paper presents results of experimental deployment of a large instrumented cylinder of variable nose geometry and center of mass offset (CMO) in free-fall in realistic environment. Data on four tests series in the Gulf of Mexico are presented and analyzed statistically. The stochastic nature of the problem of the cylinder free-falling through water is outlined and described as an input to the subsequent impact burial prediction package. Significance of the CMO on the behavior of the cylinder is underlined. Influence of the release conditions on trajectory is discussed and found to affect the behavior of the cylinders only in the first 3.5 m of free-fall in water. Beyond this depth, quasi-stable (in the mean sense) conditions are achieved. Effects of three different nose shapes-blunt, hemispherical, and chamfered-on cylinder behavior are analyzed and found to have a pronounced influence on the fall trajectory. The blunt nose shape appears to be hydrodynamically most stable in free-fall. Apparent periodicity in motions of all cylinders were noted and were found to be the function of the CMO and nose shape primarily. Implications of these and other findings on modeling and impact burial predictions are discussed.