Effect of foliation orientation on the P- and S-wave velocity anisotropies and dynamic elastic constants of the quartz-micaschists metamorphic rocks,Angouran mine,Iran

Laboratory measurements are required to study geophysical properties of the subsurface because of lacking direct observation of Earth’s crust. In this research, compressional (P) and shear (S) wave velocity measurements have been conducted on cylindrical specimens of Quartz-micaschist cored using rock blocks taken from the zinc and lead Angouran mine, Zanjan, northwest of Iran. Cylindrical rock specimens were prepared from the blocks by coring in 0°, 30°, 45°, 60°, and 90° into the foliation direction. P- and S-wave velocities were measured along the cylindrical specimens with different foliation orientations. Percent variations of the P- and S-wave velocities (Thomsen’s anisotropic parameters ε and γ) and constant dynamic modulus of test results have been determined. Percent variations of the P-wave velocity (ε) increase with an increase of the foliation angle with respect to the propagating waves direction by a parabolic function as it shows P-wave velocity differences up to a maximum value of 50 %. Thomsen’s anisotropic parameter of γ has also the same function with the foliation angle. Meanwhile, foliation orientation has a much greater influence on ε than γ for foliation angle from 45° to 90° as \( \frac{\varepsilon }{\gamma } \) ratio increases with an increase of foliation angle. Values of dynamic elastic modulus (E), Poisson’s ratio (ν), shear modulus (μ), bulk modulus (K), and Lamé’s constant (λ) increase with the increase of foliation angle with the parabolic function. The results show that dynamic elastic modulus, Poisson’s ratio, shear modulus, bulk modulus, and Lamé’s constant have anisotropic behavior in relation with the foliation orientation.     

Single-crystal structure and Raman spectroscopy of synthetic titanite analog CaAlSiO<Subscript>4</Subscript>F

Synthetic CaAlSiO₄F, the Al-F analog of titanite, has been investigated using single-crystal synchrotron diffraction experiments at Beamline X06DA (Swiss Light Source, Paul Scherrer Institute, Villigen, Switzerland) and Raman spectroscopy. The presented structural model with 40 parameters was refined against 506 unique reflections to a final R _{o b s} of 0.026 (space group A2/a, a = 6.9120(11), b = 8.5010(10), c = 6.435(2) Å, β = 114.670(11)°, and Z = 4) and exhibits less distorted coordination polyhedra than earlier models from powder data. Vibrational spectra were calculated in harmonic approximation at the Γ point from fully relaxed energy optimisations of the crystal structure, using 3D-periodic density functional theory with Gaussian basis sets and the software CRYSTAL06. The lattice parameters of the fully relaxed structure were in good agreement with the experimental values, with the calculated values 0.8 ± 0.4 % too large; the monoclinic angle was calculated 0.4° too large. The agreement of the calculated Raman frequencies with the observed ones was very good, with standard deviation ±3 cm^?1 and maximum deviations of ±7 cm^?1. Furthermore, a detailed discussion of the atomic displacements associated with each Raman mode is given.     

Community vulnerability to hazards: introducing local expert knowledge into the equation

The accuracies of three different evolutionary artificial neural network (ANN) approaches, ANN with genetic algorithm (ANN-GA), ANN with particle swarm optimization (ANN-PSO) and ANN with imperialist competitive algorithm (ANN-ICA), were compared in estimating groundwater levels (GWL) based on precipitation, evaporation and previous GWL data. The input combinations determined using auto-, partial auto- and cross-correlation analyses and tried for each model are: (i) GWL _t?1 and GWL _t?2; (ii) GWL _t?1, GWL _t?2 and P _t ; (iii) GWL _t?1, GWL _t?2 and E _t ; (iv) GWL _t?1, GWL _t?2, P _t and E _t ; (v) GWL _t?1, GWL _t?2 and P _t?1 where GWL _t , P _t and E _t indicate the GWL, precipitation and evaporation at time t, individually. The optimal ANN-GA, ANN-PSO and ANN-ICA models were obtained by trying various control parameters. The best accuracies of the ANN-GA, ANN-PSO and ANN-ICA models were obtained from input combination (i). The mean square error accuracies of the ANN-GA and ANN-ICA models were increased by 165 and 124% using ANN-PSO model. The results indicated that the ANN-PSO model performed better than the other models in modeling monthly groundwater levels.     

Finite-difference modelling of anisotropic wave scattering in discrete fracture model

The presence of fractures in reservoir rocks causes scattering of seismic wave energy. In this paper, we utilize the finite-difference modelling technique to study these scattering effects to gain more insights into the effects and assess the validity of using anisotropic wave scattering energy as a diagnostic tool to characterize fractured hydrocarbon reservoirs. We use a simplified fractured reservoir model with four horizontal layers with a fractured-layer as the third layer. The fractures are represented by grid cells containing equivalent anisotropic medium by the use of the linear slip equivalent model. Our results show that the scattered energy, quantified through estimates of the seismic quality factor (Q) is anisotropic, exhibiting a characteristic elliptical (\(\cos 2\theta \)) variations relative to the survey azimuth angle \(\theta \). The fracture normal is inferred from the minor axis of the Q ellipse. This direction correlates with the direction of maximum wave scattering. Minimum wave scattering occurs in the fracture strike direction inferred from the major axis of the Q ellipse. These results provide more complete insights into anisotropic wave scattering characteristics in fractured media and thus, validate the practical utility of using anisotropic attenuation attribute as an additional diagnostic tool for delineation of fracture properties from seismic data.     

Supersoft X-ray sources. parameters of stellar atmospheres

ROSAT spectra of 11 supersoft X-ray sources are approximated with theoretical spectra obtained in LTE models for the atmospheres of hot white dwarfs with line blanketing. The confidence intervals of parameters derived from these approximations—T_eff, log, g, N_H, and R²/d²—are determined. The results are compared with predictions for a model with stable/recurrent thermonuclear burning on the white-dwarf surface.     

Modelling the effects of porous media deformation on the propagation of water-table waves in a sandy unconfined aquifer

This paper examines the influence of porous media deformation on water-table wave dispersion in an unconfined aquifer using a numerical model which couples Richards’ equation to the poro-elastic model. The study was motivated by the findings of Shoushtari et al. (J Hydrol 533:412–440, 2016) who were unable to reproduce the observed wave dispersion in their sand flume data with either numerical Richards’ equation models (assuming rigid porous media) or existing analytic solutions. The water-table wave dispersion is quantified via the complex wave number extracted from the predicted amplitude and phase profiles. A sensitivity analysis was performed to establish the influence of the main parameters in the poro-elastic model, namely Young’s modulus (E) and Poisson’s ratio (ν). For a short oscillation period (T?=?16.4 s), the phase lag increase rate (k _i) is sensitive to the chosen values of E and ν, demonstrating an inverse relationship with both parameters. Changes in the amplitude decay rate (k _r), however, were negligible. For a longer oscillation period (T?=?908.6 s), variations in the values of E and ν resulted in only small changes in both k _r and k _i. In both the short and long period cases, the poro-elastic model is unable to reproduce the observed wave dispersion in the existing laboratory data. Hence porous media deformation cannot explain the additional energy dissipation in the laboratory data. Shoushtari SMH, Cartwright N, Perrochet P, Nielsen P (2016) The effects of oscillation period on groundwater wave dispersion in a sandy unconfined aquifer: sand flume experiments and modelling. J Hydrol 533:412–440.     

Stability and phase relations of nonstoichiometric clinopyroxenes in the join diopside-Ca-Eskola component at high pressures

The stability of nonstoichiometric clinopyroxenes in the Di-CaEsk join was experimentally studied, and phase diagrams were constructed for this join at pressures of 2.0 and 3.0 GPa. It was found that melting in the diopside part of the join occurs at anomalously low temperatures, and nonstoichiometric clinopyroxene coexists with a phase approaching diopside in composition. Phase relations along the Di-CaEsk join can be described and consistently interpreted only assuming that the diopside phase (α-diopside) is thermodynamically stable. The following phase volumes were observed along the solidus of the join at a pressure of 3.0 GPa: Cpx, αDi+Cpx, αDi+Cpx+Qtz, αDi+Cpx+Grt+Qtz, Cpx+Grt+Qtz, Cpx+Grt+Ky+Qtz, Grt+Ky+Qtz. Melting occurs via the eutectic reaction αDi+Cpx+Grt+Qtz=L at a temperature of about 1200°C in the diopside part of the system and via the eutectic reaction Cpx+Grt+Ky+Qtz=L at a temperature of 1400°C in the calcium-rich part of the system. At a pressure of 2.0 GPa, melting occurs at temperatures of 1200–1300°C via the eutectic reaction αDi+Cpx+ An + Qtz=L. The invariant equilibrium (L, An, Cpx, Grt, αDi, Qtz) lies within the pressure range 2.0–3.0 GPa. Nonstoichiometric clinopyroxenes form complex solid solutions, the compositions of which are not strictly confined to the Di-CaEsk join and depend on temperature, pressure, and phase association. Grossular garnets coexist with nonstoichiometric clinopyroxenes and α-diopside.     

Biostratigraphy and floristic evolution of coal swamp floras of a part of Talcher Basin,India: a window on a Permian temperate ecosystem

The present megafloral assemblage recorded from the Barakar sediments of Dholpahar section along Singda rivulet near Gopal Prasad Village in Talcher Basin comprises of equisetaceous stems, Gangamopteris buriadica, Palaeovittaria kurzii and 19 species of the genus Glossopteris. Record of Gangamopteris, Palaeovittaria and many narrow mesh forms of Glosspteris viz., G. angustifolia, G. churiensis, G. communis, G. recurva, G. spatulata, G. stenoneura, G. tenuifolia, G. vulgaris and G. zeilleri from two older fossiliferous horizons demonstrates that these fossils were preserved during Lower Barakar sedimentation. The report of middle and broad mesh forms of Glossopteris viz., G. barakarensis, G. browniana, G. indica, G. intermittens, G. karharbariensis, G. nakkarea, G. oldhamii, G. taeniensis and G. retifera in the youngest fossiliferous horizons reveals that these fossils were preserved during the deposition of Upper Barakar sediments. The continuation of some of the Karharbari plant fossils in the early phase of Barakar Formation and their disappearance in the flora of Late Barakar suggests a shift in the climatic setup. Palaeoclimate and palaeovegetation of this area are also summarised in this study. Moreover, the fossil assemblages of different fossiliferous beds of Dholpahar section demonstrate the evolution of midrib and meshes in different reticulate leaves.     

Paleoweathering and Paleoclimatic Reconstructions using Neoproterozoic Paleosol in the Eastern Margin of the Pranhita-Godavari Basin,India

Paleogene sediments of the inner fold belt, Naga hills, have very well preserved ichnofossils. 16 ichnospecies have been documented among 13 ichnogenera such as Arenicolites isp., Chondrites targionii, Cylindrichnus isp., Diplocraterion parallelum, Gyrochorte isp., Ophiomorpha annulata, O. irregulaire, O. nodosa, O. rudis, Palaeophycus tubularis, Planolites beverleyensis, Scolicia palaeobullia, Skolithos linearis, Trypinites weisei, Thalassinoides horizontalis and Zoophycos isp. The ichnofossil assemblages comprise mostly domichnia and fodinichnia benthos of the Skolithos and Cruziana ichnofacies. A shallow marine nearshore to offshore marine environment with fluctuating energy condition has been envisaged.     

Analytical expressions for three-phase generalized relative permeabilities in water- and oil-wet capillary tubes

We analyze three-phase flow of immiscible fluids taking place within an elementary capillary tube with circular cross-section under water- and oil-wet conditions. We account explicitly for momentum transfer between the moving phases, which leads to the phenomenon of viscous coupling, by imposing continuity of velocity and shear stress at fluid-fluid interfaces. The macroscopic flow model which describes the system at the Darcy scale includes three-phase effective relative permeabilities, K _{i j,r} , accounting for the flux of the ith phase due to the presence of the jth phase. These effective parameters strongly depend on phase saturations, fluid viscosities, and wettability of the solid matrix. In the considered flow setting, K _{i j,r} reduce to a set of nine scalar quantities, K _{i j,r} . Our results show that K _{i j,r} of the wetting phase is a function only of the fluid phase own saturation. Otherwise, K _{i j,r} of the non-wetting phase depends on the saturation of all fluids in the system and on oil and water viscosities. Viscous coupling effects (encapsulated in K _{i j,r} with i ≠ j) can be significantly relevant in both water- and oil-wet systems. Wettability conditions influence oil flow at a rate that increases linearly with viscosity ratio between oil and water phases.     

Effects of crack inclination on shear failure of brittle geomaterials under compression

A micromechanics-based approach is proposed to predict the shear failure of brittle rocks under compression. Formulation of this approach is based on an improved wing microcrack model, the Mohr-Coulomb failure criterion, and a micro-macro damage model. The improved wing microcrack model considers the effects of crack inclination angle on mechanical behaviors of rocks. The micro-macro damage model describes the relation between crack growth and axial strain. Furthermore, comparing experimental and theoretical relations between crack initiation stress and confining pressure, model parameters (i.e., μ, a, β, and φ) hardly measured by test are solved. Effects of crack inclination angle, crack size, and friction coefficient on stress-strain relation, compressive strength, internal friction angle, cohesion, shear failure plane angle, and shear strength are discussed in details. A most disadvantaged crack angle is found, which is corresponding to the smallest compressive strength, cohesion, internal friction angle, and shear strength of rocks. Rationality of the theoretical results is verified by the published experimental results. This approach provides a theoretical prediction for effects of microcrack geometry on macroscopic shear properties in brittle rocks under compression.     

The biostratigraphic and paleoecological importance of the subsurface Carboniferous microfossil assemblages from Faghur-1x well,Western Desert of Egypt

The microfossil assemblages of subsurface Carboniferous rocks from Faghur-1x were examined and identified. Their biostratigraphical and paleoenvironmental importance were investigated. The assemblage included well-preserved foraminifera like Omphalotis omphalota, Omphalotis sp. 2, Omphalotis sp. 3, Paraarchaediscus stilus, Paraarchaediscus koktjubensis, Archaediscus krestovnikovi, Archaediscus complanatus, Archaediscus inflatus, Archaediscus karreri, Diplosphearina inequalis, Eotubertina sp., Tetrataxis conica, Cribrostomum lecomptei, Palaeotextularia angulata, and Palaeotextularia longiseptata. This foraminiferal association indicates the late Viséan-early Serpukhovian. The other microfossils are gastropods, brachiopods, ostracods, crinoidal ossicles, frond-like fenestrate bryozoan types and stick-like colonies, echinoderms, microproblematica like Draffania biloba and algal Calcisphaera and the dasyclad Koninckopora. This microfossils assemblage points to the deposition in a restricted to open platform in a lagoonal framework environment. The Tehenu Basin is the eastern segment of northern African Sahara basins that provided refuge for the foraminiferal genera through the mass extinction events during the glacial Viséan-Serpukhovian times. However, its foraminiferal associations have lower diversities than the western basins, which indicate that it was more readily affected by the mass extinction event.     

Elastic behavior of vanadinite,Pb<Subscript>10</Subscript>(VO<Subscript>4</Subscript>)<Subscript>6</Subscript>Cl<Subscript>2</Subscript>, a microporous non-zeolitic mineral

The high-pressure behavior of a vanadinite (Pb₁₀(VO₄)₆Cl₂, a = b = 10.3254(5), c = 7.3450(4) Å, space group P6₃/m), a natural microporous mineral, has been investigated using in-situ HP-synchrotron X-ray powder diffraction up to 7.67 GPa with a diamond anvil cell under hydrostatic conditions. No phase transition has been observed within the pressure range investigated. Axial and volume isothermal Equations of State (EoS) of vanadinite were determined. Fitting the P–V data with a third-order Birch-Murnaghan (BM) EoS, using the data weighted by the uncertainties in P and V, we obtained: V ₀ = 681(1) Å³, K ₀ = 41(5) GPa, and K′ = 12.5(2.5). The evolution of the lattice constants with P shows a strong anisotropic compression pattern. The axial bulk moduli were calculated with a third-order “linearized” BM-EoS. The EoS parameters are: a ₀ = 10.3302(2) Å, K ₀(a) = 35(2) GPa and K′(a) = 10(1) for the a-axis; c ₀ = 7.3520(3) Å, K ₀(c) = 98(4) GPa, and K′(c) = 9(2) for the c-axis (K ₀(a):K ₀(c) = 1:2.80). Axial and volume Eulerian-finite strain (fe) at different normalized stress (Fe) were calculated. The weighted linear regression through the data points yields the following intercept values: Fe _a (0) = 35(2) GPa for the a-axis, Fe _c (0) = 98(4) GPa for the c-axis and Fe _V (0) = 45(2) GPa for the unit-cell volume. The slope of the regression lines gives rise to K′ values of 10(1) for the a-axis, 9(2) for the c-axis and 11(1) for the unit cell-volume. A comparison between the HP-elastic response of vanadinite and the iso-structural apatite is carried out. The possible reasons of the elastic anisotropy are discussed.     

Microbiostratigraphy of the Upper Paleocene to Middle Eocene Jahrum Formation in the Folded Zagros Zone,SW Iran

The Jahrum Formation (Upper Paleocene to Middle Eocene) is composed of carbonate and dolomitic carbonate rocks in the Zagros Basin. The Zagros is located at the boundary between the Arabian and Eurasian lithosphere plates and represent the orogenic response to a collision between Eurasia and advancing Arabia during the Cenozoic. The study area is located in the northern part of Kuh-E-Tudej, ~175 km southeast of Shiraz in the Folded Zagros Zone. The Jahrum Formation at Kuh-E-Tudej, with a thickness of 190 m, consists of medium to massive bedded limestone. The following foraminiferal index species are identified in the studied section: Fallotella alavensis, Kathina sp., Miscellanea sp., Lockhartia sp.,Orbitolites shirazeinsis, Nummulites sp., Opertorbitolites sp., Dictyoconus cf. egyptiensis, Orbitolites cf. complanatus, Dictyoconus sp., Coskinolina sp., Somalina stefaninii, Discocyclina sp., Praerhapydionina sp., Coskinolina cf. liburnica, Nummulites cf. globulus, Nummulites cf. aturicus, and Alveolina sp. The age of the studied sediments ranges from Upper Paleocene to Middle Eocene. The microbiostratigraphic studies revealed four biozones based on the foraminifers identified in the studied section.     

Modeling and mapping of solar radiation using geostatistical analysis methods in Iran

Because of economic and technical limitations, measuring solar energy received at ground level (R _s ) isn’t possible in all parts of the country, and in only 12% of synoptic stations is this parameter measured and recorded. Thus, it should be estimated and modeled spatially based on other climatic variables using mathematical methods. In this research, many attempts have been made to introduce an air temperature-based model for Rs estimation, and then, based on the output of the mentioned models, several geostatistical methods have been tested, and finally an elegant spatial model is proposed for (Rs) zoning in Iran. In this regard, the relationships between the measured amounts of monthly solar radiation and other climatic parameters, such as a monthly average, maximum and minimum temperature, precipitation, relative humidity, and the number of sunny hours during the period 1970–2010, are examined and modeled. It was revealed that based on the linear relationship between the monthly average air temperatures and solar radiation values recorded in each of the stations, that the best-fit linear model, with R ²  = 0.822, MAE = 1.81, RMSE = 2.51%, and MAPE = 10.08, can be introduced for Rs estimation. Then, using the outputs of the proposed model, the amounts of (R _s ) are estimated in another 171 meteorological stations (a total of 192 stations), and eight geostatistical methods (IDW, GPI, RBF, LPI, OK, SK, UK, and EBK) were investigated for zoning. Comparing the resulting variograms showed that in addition to proof of spatial correlation between solar radiation data, they can be applied for modeling changes in various directions. Analyzing the ratio of the nugget effect on the roof of the variograms showed that the Gaussian model with the lowest ratio (Co/Co + C = 0.883) and (R ²  = 0.972), could model the highest correlation between the data and, therefore, it was used for data interpolation. To select the best geostatistical model, R2, MAE, and RMSE were used. On this basis, it was found that the RBF method with R ²  = 0.904, MAE = 3.02, RMSE = 0.39% is the most effective. Also, the IDW method with R ²  = 0.90, MAE = 3.08, RMSE = 0.391%, compared to other methods is the most effective. In addition, for data validation, correlations between observed and estimated values of solar radiation were studied and found R ²  = 0.86.     

<Emphasis Type="Italic">Salpingoporella</Emphasis> (dasycladalean algae) species from the Lower Cretaceous carbonate facies of Kopet Dagh basin (NE Iran)

Salpingoporella species from algal bearing of Barremian-Aptian limestones in the Kopet Dagh basin (NE of Iran) are described. Different species (S. cemi, S. hasi, S. heraldica, S. hispanica, S. milovanovici, S. muehlmbergi, S. parapiriniae, S. piriniae, S. cf. biokovensis, S. steinhauseri, S. polygonalis) are investigated from different biometrical aspects such as depositional environments and biogeographical distribution as well as their systematic palaeontology from two formations (the Tirgan and Sarcheshmeh formations) in nine stratigraphic sections.     

A new Jurassic cow shark (Chondrichthyes,Hexanchiformes) with comments on Jurassic hexanchiform systematics

A new taxon, ?Crassodontidanus gen. nov. of Hexanchiformes (cow sharks) from the Jurassic of Germany is described. It is characterized by peculiar teeth combining apomorphic (serrated mesial cutting edge of the main cusp) and plesiomorphic features (deep root with convex mesial and distal margins in labial and lingual views; protruding lingual root bulge). This character combination readily distinguishes members of the new taxon from all other known extant (Heptranchias, Hexanchus, Notorynchus) and extinct (?Gladioserratus, ?Notidanodon, ?Notidanoides, ?Pachyhexanchus, ?Paraheptranchias, ?Weltonia) hexanchiforms. Currently, two species, ?C. serratus (type species; Late Jurassic, Late Kimmeridgian of Nusplingen, South Germany) and ?C. wiedenrothi (Early Jurassic, Early Pliensbachian of Gretenberg (Hanover), North Germany) are assigned to this taxon. ?Crassodontidanus gen. nov. is member of ?Crassonotidae fam. nov. and sister to ?Notidanoides Maisey, 1986 and ?Pachyhexanchus Cappetta, 1990. We consider ?Notidanus amalthei Oppel, 1854 from the Pliensbachian of South Germany, ?Notidanus insignis Seguenza, 1887 from the Oxfordian of Sicily (Italy) and ?Notidanus wagneri Agassiz, 1843 from the Early Tithonian of Solnhofen (South Germany) nomina dubia and nomina nuda, respectively. The family ?Crassonotidae comprises plesiomorphic hexanchiforms ranging from the Sinemurian (Early Jurassic) to the Hauterivian (Early Cretaceous).     

Bounding relationships between parameters of earthquakes and seismogenic clastic dikes (based on worldwide data)

This paper presents the first boundary equations describing the relationship between earthquake parameters (magnitude M _S and macroseismic intensity I _P at the observation point on the MSK-64 scale) and clastic dikes (having maximal thickness m _cd , visible height h _cd , and the index of manifestation intensity of dikes in the cross section I _cd ). As was expected, the maximal size of dikes grows with an increase in the earthquake magnitude and macroseismic intensity. Analysis of the dependences showed that it is better to use all three parameters for estimation of the minimal threshold M _S or I _P from clastic dikes, and, in the absence of data on seismogenic rupture, the maximal calculated value should be used. Some limitations in application and the advantages of the equations obtained are discussed with respect to characterizing earthquakes of the pre-instrumental period.     

Biostratigraphy of the Çeşmeler and Elmalι Dere formations: First records of upper Cretaceous planktonic foraminifera and radiolarians from the Eastern Pontides (Maçka,Trabzon, Turkey)

Upper Cretaceous pelagic deposits outcropping in the Maçka (Trabzon) region include radiolarians and pelagic foraminifera. The Çatak Group represented by the volcano-sedimentary successions consists of three formations having different properties. Two sections, ÇTK1 and ÇTK2, are selected from the Çe meler and Elmalι Dere formations, respectively, establishing the biostratigraphy of outcropping sedimentary units. A total of 17 species of Whiteinella, Helvetoglobotruncana, Marginotruncana, Dicarinella, Praeglobotruncana, Archaeoglobigerina and Hedbergella demonstrating the early Turonian–Coniacian are established in the ÇTK1 stratigraphic section. The early Turonian radiolarian fauna consisting of Halesium sexangulum Pessagno, 1971, Crucella cachensis Pessagno, 1971, Stichomitra communis Squinabol, 1903 is also defined in the same section. A total of 30 species of Crucella, Halesium, Pessagnobrachia, Patulibracchium, Alievium, Archaeospongoprunum, Dicyomitra, Stichomitra, Diacanthocapsa, Dactiyliodiscus, Amphipydax, Pseudoaulophocus, Acaeniotyle, Archaeodictyomitra, Actinomma, Xitus, Neosciadocapsidae characterizing the early and late Turonian, as well as the Coniacian–early Santonian are recognized from red-coloured pelagic limestones of the ÇTK2 section. Also, planktonic foraminifera species of Marginotruncana, Hedbergella, Heterohelix, Globotruncana, Globotruncanita, Archaeoglobigerina, Dicarinella characterizing the Coniacian–Santonian are described in the thin sections of the same samples. The age of red-coloured limestones is identified as the Coniacian–Santonian benefit from radiolarians and pelagic foraminifera. Consequently, radiolarians and pelagic foraminifera within sedimentary successions of the investigation area are distributed in two intervals that coincide with the early Turonian–Coniacian and Coniacian–Santonian intervals.     

HeII <Emphasis Type="Italic">λ</Emphasis>304 emission above sunspot umbrae

Observations of sunspot umbrae in the HeII λ304 Å and HeI λ10830 Å lines are analyzed and compared. Spectral observations in the HeI λ10830 line obtained on the Large Non-Eclipse Solar Coronograph of the Sayan Solar Observatory are used, together with HeII λ304 data obtained with the SOHO/EIT and CORONAS-f spacecraft. The contrast in the HeII λ304 line was chosen as an indicator of the UV flux. The dependences of the contrast in the HeII λ304 line and the parameters of the HeI λ10830 IR triplet on the sunspot area are obtained. The sunspot areas were determined using white-light images. A division of the dependences of the parameters of the HeI λ10830 and HeII λ304 lines on the sunspot area into two branches can be distinguished for leading and trailing sunspots. Possible origins of this behavior of the line parameters are discussed.