Mechanical Behavior of Light-Weight Soil Under Consolidated Drained Shear Condition

To reveal the influence of material composition on mechanical properties of light-weight soil, stress-strain -volumetric strain characteristics and Poisson's ratio of mixed soil were researched by consolidated drained shear tests. The results show that light-weight soil is a kind of structural soil, so its mechanical properties are affected by mixed ratio and confining pressure, and mixed soil possesses structural yield stress. When confining pressure is less than the structural yield stress, strain softening occurs; when confining pressure is more than the structural yield stress, strain hardening is observed. There are two kinds of volume change behavior: shear contraction and shear dilatancy. Shear dilatancy usually leads to strain softening, but there isn't an assured causal relationship between them. Poisson's ratio of mixed soil is a variational state parameter with the change of stress state, it decreases with increased confining pressure, and it increases with increased stress level. When axial strain is near 5%, Poisson’ ratio is gradually close to a steady value. The main range of Poisson's ratio is 0.25～0.50 when confining pressure changes from 50 to 300 kPa. When unconfined compressive strength of mixed soil is less than 328 kPa, its stress-strain-volumetric strain characteristics can be predicted very well by Duncan-Chang model (E-B model). However, when the range of unconfined compressive strength is [328 kPa, 566 kPa], the model can't predict stress-strain characteristics accurately when confining pressure is under 200 kPa, and it also can't predict the strong shear dilatancy phenomenon of mixed soil under low confining pressure.     

Study of dilatancy behaviors of calcareous soils in a triaxial test

Abstract

In this article, the dilatancy of calcareous soil is studied systematically based on triaxial consolidation drainage shear tests, and the difference in dilatancy between calcareous soil and siliceous soil is also investigated. It was found that: ① Calcareous soil experience obvious dilated deformation. Dilatancy tendency increases with increasing related density and decreases with increasing confining pressure. ② The volumetric strain rate initially increases from negative to positive. After it reaches a maximum, there is a small decrease in the volumetric strain rate, but it is still greater than zero, and the stress-strain curves are of softening type. ③ For the same condition, the dilatancy deformation of calcareous sand begins later than that of siliceous sand, and the volume compression before dilatancy is also larger for calcareous sand. ④ The critical state alone cannot accurately describe the entire deformation process of soil, and it is proposed that the phase transformation state be added to the standard method used to assess soil dilatation and contraction. ⑤ Based on the statistical analysis of experimental data, mathematical relationships were established between void ratio, relative density, and effective confining pressure of phase transformation state and critical state, respectively.

• Highlights

• Reports results from a well-designed experiment that includes a good amount of samples and data.

• Effects of relative density and effective confining pressure on deformation mode and mechanical properties of calcareous sand are evaluated.

• The difference in dilatancy between calcareous sand and siliceous sand was compared

• The phase-transformation state and critical state were compared with the axial strain, volumetric strain and deviatoric stress.

• Using phase-transformation void ratio and critical void ratio to describe the whole deformation process of calcareous sand is proposed.

• The mathematical expressions of phase-transformation void ratio and critical void ration were given, respectively.

     

Stiffness Degradation of Undisturbed Saturated Soft Clay in Yangtze Estuary under Complex Stress Conditions

Stiffness degradation will occur due to the generation of accumulated pore pressure in saturated soft clays under cyclic loading. The soil static-dynamic multi-purpose triaxial and torsional shear apparatus in Dalian University of Technology was employed to perform different types of test on saturated soft marine clay in the Yangtze estuary. Undisturbed samples of the clay were subjected to undrained cyclic vertical and torsional coupling shear and cyclic torsional shear after three-directional anisotorpic consolidation with different initial consolidation parameters. Investigated were the effects of the initial orientation angle of the major principal stress, initial ratio of deviatoric stress, initial coefficient of intermediate principal stress and continuous rotation of principal stress axes on the stiffness degradation. It is found that the degradation index decreases (or degradation degree increases) significantly with increasing initial orientation angle of the major principal stress and initial ratio of deviatoric stress. Compared to the effects of the initial orientation angle of the major principal stress and initial ratio of deviatoric stress, the effect of initial coefficient of intermediate principal stress is less evident and this trend is more clearly reflected by the results of the cyclic torsional shear tests than those of the cyclic coupling shear tests. At the same cycle number, the degradation index obtained from the cyclic torsional shear test is higher than that from the cyclic coupling shear test. The main reason is that the continuous rotation in principal stress directions during cyclic coupling shear damages the original structure of the soil more than the cyclic torsional shear does. Based on a series of experiments, a mathematical model for stiffness degradation is proposed and the relevant parameters are determined.     

低围压水平下砂的排水行为(英文)

采用干样沉降法制备样品 ,选用静三轴仪对松砂和密砂样在 10 k Pa至 10 0 k Pa的低围压下的排水行为进行了实验研究 ,并对实验结果作了橡皮膜校正 ,在围压为 10 k Pa的密砂实验中 ,轴向应力的校正值可达到 12 %。实验研究表明低围压下松砂的剪胀性非常明显 ,且存在剪应力极值 ;围压越低 ,松砂和密砂的剪应力极值越小 ,达到最大剪应力所对应的剪应变越小。同时还表明低围压范围内相对密度不同 ,砂的应力应变特性不同 ;此外 ,低围压下砂的内摩擦角高于高围压下的值 ,从而在工程上应重视低围压水平下砂土工程参数的合理选取     

Use of Lade's Single Surface Work-Hardening Model to Investigate Mechanical Behavior of Decomposed Soils

In this study, it was attempted to assess soil parameters necessary for Lade's single surface work-hardening model that reviewed the physical and mechanical properties of granite soil located in Korea based on the results of triaxial compression tests. In addition, finite element analyses coupled with the determined soil parameters as inputs were conducted based on Lade's single surface work-hardening model and the results were compared with element test results. It could be seen that, in predicting undrained mechanical behavior, the single surface model was reproducing the stress-strain relation obtained through element tests at high accuracy. It is worthwhile to inform that these differences in the initial loading stage and the impossibility to predict swelling behavior are caused by the fact that there is no prediction model for changes in shear properties, especially in dilatancy properties due to particle crushing occurring while element tests are conducted. Hence, it is concluded that, to expand the applicability of Lade's single surface work-hardening constitutive model to practical problems, the model should be modified in relation to the dilatancy of soils.     

A method analyzing deformation of anchor foundations in soft clay under static and cyclic loads

The paper presents a constitutive model to describe undrained cyclic stress-strain responses of soft clays based on the equivalent visco-elastic and creep theories. The hysteretic and nonlinear stress-strain responses of soft clays are described using the equivalent visco-elastic relationship and variations of the cyclic modulus and the damping ratio with the octahedral shear strain, respectively in the model. The cyclic accumulative strain is described using the Mises creeping potential function and the associated flow rule. The method determining the model parameters is given by static and cyclic triaxial tests. The finite element method to analyze deformation of anchor foundation in soft clay under static and cyclic loads is developed based on the model. For the method, a cyclic loading time history is divided into a series of incremental loading sub-processes which include one load cycle at least. The cyclic stress-strain responses of soil elements at any time are not tracked in detail and determined by the equivalent visco-elastic calculations for every loading sub-process. The accumulative deformation of anchor foundations is calculated using the initial strain algorithm. The method has been implemented in ABAQUS Software by developing interface programs. Model tests of the suction anchors are conducted and predicted using the method. Comparisons of predicted and model test results show that the method can be used to evaluate cyclic stability and reveal the failure process and mechanism of anchor foundations by analyzing deformation time-histories.     

Implementation of state-dependent plasticity model in strain wedge model for laterally loaded piles in sand

ABSTRACT

The strain wedge model effectively performs nonlinear analyses of the lateral response of piles by using a nonlinear stress-strain relationship to describe soil behavior in the strain wedge. In this study, a state-dependent plasticity model has been implemented in the strain wedge model to calculate the stress-strain relationship for sand in the strain wedge. To complement this implementation, the effect of dilatancy on the shear strain is considered in the strain wedge. A full-scale test and a 45 g centrifuge model test on laterally loaded piles are used to validate the proposed method. The results show that the deflections and moments predicted by the proposed method accord well with those measured from full-scale and centrifugal model pile tests. Moreover, the combination of the state-dependent plasticity model and the strain wedge model allows for analyzing the lateral response of single piles using a unique set of model parameters for different relative densities of sands. In addtion, the stress-strain response in the strain wedge, not the dilatancy, dominates the soil resistance in the strain wedge and thus the lateral response of piles.     

循环荷载作用下粉土的动力学特征

选用近海分布广泛的粉土为研究对象,利用动三轴压缩试验结果得到了动荷载作用下粉土的应力-应变关系、孔压发展模式及动强度与临界循环次数之间的关系;探讨固结围压和固结比对粉土动力学性质的影响。动力学试验结果表明,动剪切模量随着固结围压的增大而增大,动阻尼比随动剪应变幅的变化关系受围压影响不大;不同围压对动剪应力的比值影响很小,同一围压下随着固结比的增大,动剪应力比也会随之增大;不同围压及不同固结比对以Nf表示的峰值孔隙水压力发展模式影响很小。     

不同制样方式下含水合物粉细砂静力学特性研究

利用高压低温三轴仪对含水合物粉细砂进行剪切试验。分别用气饱和法与水饱和法制样,实现不同水合物饱和度和围压条件的三轴剪切,并分析含水合物砂的胶结作用对剪切特性的影响。试验结果表明：低饱和度时,气饱和与水饱和试样的偏应力差别不大;高饱和度时,制样方式对偏应力的影响较显著;水饱和试样的剪胀性大于气饱和试样,剪胀性随饱和度的升高和围压的降低而增大。峰值偏应力和稳态偏应力由黏聚力和摩擦力两部分组成,水合物的存在对稳态内摩擦角影响不大。     

Experimental study on strength characteristics and microscopic mechanism of marine soft clays

Abstract

The effect of microstructure on shear strength of saturated marine clays was investigated by conducting a series of consolidated-drained (CD), consolidated-undrained (CU) triaxial shear tests and mercury intrusion porosimetry (MIP) tests on undisturbed and reconstitute specimens. The valuable findings from the experimental study are follows: (1) The shear strength of undisturbed specimens is lower than that of corresponding reconstituted specimens due to larger void ratio at the same confining pressure. However, undisturbed specimens have higher strength than reconstituted specimens when their void ratios are the same. (2) The main reason for the lower shear strength of reconstituted specimens with the same void ratio as undisturbed specimens is that more volume of inter-aggregate pores exists in the reconstituted specimens according to the MIP test results. And the difference in shear strength between undisturbed and reconstituted specimens is mainly caused by the difference in soil fabric. (3) The shear test results dealt with a reference void ratio, as a fabric index, show that there is a unique linear relation between strength and void ratio at failure to the reference void ratio. Moreover, the linear relation is suitable for other marine clays from the literature. Therefore, the reference void ratio can be used as a soil fabric index to normalize the strength characteristics of marine soft clays.     

Modified approach to evaluation of undrained shear strength from piezocone tests in soft clays

This paper proposes a modified-theoretical approach to interpreting the undrained shear strength from piezocone tests in clays. Assuming the shear and normal stresses on the cone face to be the friction at the cone–soil interface and the ultimate expansion pressure, respectively, an expression of the tip resistance is first derived at force equilibrium. The undrained shear strength is then determined by combining the derived expression of tip resistance with the formulation for pore pressure at the cone shoulder position. Many factors, such as the penetration rate and the cone roughness, are considered in this model. Different shaped model penetrometers, including cone- and ball-shaped ones, are adopted in centrifuge tests to investigate the validity of the proposed method. The undrained shear strength estimated from the piezocone test is found to agree well with that from ball penetrometer test. Case studies are also presented to show the application of the proposed method. Comparisons between the predicted and measured values of undrained shear strength indicate that the proposed approach is generally applicable for nonfissured clays, especially intact clays.     

A simple experimental method to regain the mechanical behavior of naturally structured marine clays

Quantitative laboratory studies on the structural behavior of natural intact marine clays require a large number of identical natural samples leading to an expensive and challenging task. This study proposes a simple method to reconstruct an artificial structured marine clay as the state of its natural intact clay at both macro and micro levels. For this purpose, the Shanghai marine clay is selected and mixed with low cement contents (1–6%). The clay-cement slurry is mixed in a container with the ice-covered sides at a low temperature about 0 ± 2 °C to postpone the hydration reactions until consolidation began. The purpose of adding cement is to generate the inter-particle bonding and structure in reconstituted samples. Initially, the reconstituted samples are consolidated under the in situ stress of 98 kPa and then under the pre-consolidation pressure of 50 kPa. Mechanical characteristics such as compression index, yield stress, unconfined compression strength, shear strength ratio, and the stress paths from triaxial tests are compared with natural intact clay accordingly. Scanning electron microscope and mercury intrusion porosimetry analyses are also performed to analyze the microstructure of clays for comparison. Furthermore, the proposed method is also examined by using natural intact marine clays of different locations and characteristics.     

Comparison Between Shear Behaviors of Overconsolidated Nakdong River Sandy Silt and Silty Sand

From this research, overconsolidated undrained and drained behaviors of specimens with high sand content were highly dilatant. According to the comparison results of laboratory tests, the deviator stresses of silty sand were greater than sandy silt due to high sand content under increasing OCRs, and both silty sand and sandy silt were presented strain softening tendency after failure under undrained loading. The pore water pressure increased with increasing fines content under increasing OCRs. Silty sand exhibited more dilatancy and increasing shear strength than sandy silt because pore water pressures of silty sand were lower than sandy silt under higher OCRs. In overconsolidated drained tests, silty sand is higher strength than sandy silt because silty sand has a lower volumetric strain and higher deviator stress than sandy silt under increasing OCRs. As the degree of overconsolidation increased, similar behaviors of silty sand and sandy silt observed that volumetric strain decreased to negative values due to dilatancy effect and low-cohesion under current effective confining pressures.     

南中国海神狐海域天然气水合物上覆地层不排水抗剪强度预测

浅层沉积物不排水抗剪强度（Su）是深水作业的关键参数之一。为了获取南海神狐海域首次海域天然气水合物试采区W18-19框体的基本工程地质特征,试采工程准备阶段开展了原位孔压静力触探测试（CPTU）及大量的室内实验。本文将主要基于CPTU计算不排水抗剪强度的基本模型,采用微型十字板、电动十字板、袖珍贯入仪及不固结不排水三轴实验,确定该区域不排水抗剪强度的基本模式,并提出适用于南海神狐钙质黏土层的不排水抗剪强度纵向分布规律计算模型,对该区域水合物上覆层的不排水抗剪强度进行预测。 结果表明,基于总锥端阻力、有效锥端阻力、超孔隙压力的模型系数分为13.8、4.2、14.4。综合考虑地层压实效应和含气情况,本文提出的分段函数预测模型与室内结果的一致性较好,可用于工程设计阶段进行工区不排水抗剪强度纵向分布规律的预测。另外,基于有效锥端阻力的不排水抗剪强度经验模型适应于浅层极软-较硬压实的钙质粘土层,基于超孔隙压力的不排水抗剪强度模型适用于较硬-坚硬的不含气层,而基于总锥端阻力的不排水抗剪强度计算模型则适用于坚硬含气的钙质黏土层。本文提出的分段函数模型有效的提高了经验模型在南海神狐水合物赋存区的适用性,计算结果可为工程安全评价提供支撑。     

Strength Sensitivity of Marine Ariake Clays

Natural Ariake clays are characterized by high sensitivity. In this study, the mechanism and the factors controlling undrained shear strengths of both undisturbed and remolded Ariake clays are discussed. A series of unconfined compressive tests were performed on undisturbed samples of natural Ariake clays. The remolded undrained shear strength is predicted using a quantitative expression derived from extensive data of remolded undrained shear strength for a number of soils compiled from resources in the literature. The sensitivity of natural Ariake clays derived from the ratio of half of unconfined compressive strength for undisturbed samples to remolded undrained shear strength is found to be affected by both natural water content and normalized water content that is defined as the ratio of natural water content to liquid limit. The smaller the natural water content, the higher the sensitivity is at the same normalized water content. At the same natural water content, the larger the normalized water content, the higher the sensitivity is.     

Axial friction response of full-scale pipes in soft clays

The axial friction response of subsea pipelines in soft clays is a very important aspect for designers of subsea pipelines but the response is not well understood so far. There is a pressing need for the comprehension of the response. In this paper, model tests are performed using full-scale pipes coated with polyethylene (PE) to study the effects of the set-up period, the pipe diameter, the buried depth of the pipe, the shear strength of soft clays and the loading rate on the axial friction response of pipelines in soft clays. The variations of the axial friction coefficient are analyzed using the effective stress method based on model test results. The results show that the axial friction resistance increases with the increasing pipe diameter but the effect of the pipe diameter on the axial friction coefficient can be neglected. The ultimate axial resistance also increases with the increase of the buried depth of pipelines, the undrained shear strength of soft clays and the loading rate. The axial friction coefficient increases with the increasing loading rate. However, the axial friction coefficient decreases with the increasing buried depth. The method to determine the axial friction coefficient is developed by analyzing model test results, which considers the effects of the diameter, the buried depth, the undrained shear strength of soft clays and the loading rate. The study results not only extend the industry data base but also supply a basis to determine the axial friction coefficient of PE-coated pipes in soft clays for ocean engineering geological investigations.     

Improvement of estuarine marine clays for coastal reclamation using vacuum-applied consolidation method

Consolidation occurs in estuarine marine clays for coastal reclamation by dissipation of the excess pore pressure, which is induced by increasing the total overburden stress during conventional mechanical surcharging. The excess pore pressure can be decreased usually by the use of several construction methods such as sand drain and paper drain. Besides the drain methods, vacuum can also be used in the soil mass to consolidate the estuarine marine clays by decreasing the pore pressure as well as increasing the effective stress.The study on vacuum consolidation is devoted so far mainly for laboratory model tests or numerical analysis in Korea. Recently, an instrumentation system was applied to manage the vacuum-applied consolidation on a field, in which a sewage disposal plant was constructed. While vacuum was applied, the behaviors of estuarine marine clays such as the settlement, lateral deformation and pore water pressure have been investigated precisely. The behavior of estuarine marine clays during vacuum-applied consolidation shows some difference from the behavior of estuarine marine clays in the case of conventional preloading. A principal difference is that the lateral deformation corresponding to settlement is smaller than before vacuum application even though the surcharge height has been increased.     

Anisotropic Drained Deformation Behavior and Shear Strength of Natural Soft Marine Clay

The deformation behavior and shear strength of soft marine clays subjected to wave or traffic loads are different from that in triaxial loading due to the changes of major principal stress direction β and intermediate principal stress coefficient b. To investigate the anisotropy affected by β and b in natural soft marine clay, a series of drained tests were conducted by hollow cylinder apparatus. The principal stress direction relative to vertical direction were maintained constant under an increasing shear stress, with fixed intermediate principal stress coefficient b. The influence of the b and β on anisotropy of typically Wenzhou intact clay is discussed. It was found that octahedral stress–strain relationships expressed anisotropy with different b and β. The friction angle and deviator stress ratio with different b and β were presented to provide guidance for engineering projects in the coastal zone.     

Strength Sensitivity of Marine Ariake Clays

ABSTRACT

Natural Ariake clays are characterized by high sensitivity. In this study, the mechanism and the factors controlling undrained shear strengths of both undisturbed and remolded Ariake clays are discussed. A series of unconfined compressive tests were performed on undisturbed samples of natural Ariake clays. The remolded undrained shear strength is predicted using a quantitative expression derived from extensive data of remolded undrained shear strength for a number of soils compiled from resources in the literature. The sensitivity of natural Ariake clays derived from the ratio of half of unconfined compressive strength for undisturbed samples to remolded undrained shear strength is found to be affected by both natural water content and normalized water content that is defined as the ratio of natural water content to liquid limit. The smaller the natural water content, the higher the sensitivity is at the same normalized water content. At the same natural water content, the larger the normalized water content, the higher the sensitivity is.     

Modeling Virgin Compression of Reconstituted Clay at Different Initial Water Contents

The observations on compressibility of reconstituted clays show that the compression line with a higher initial water content lies above the compression line with a lower initial water content for a given clay. Hence there exists additional void ratio due to initial water contents among virgin compression lines (VCLs) of reconstituted clays. In this paper, the difference in void ratio caused by different initial water contents is investigated based on the empirical equation proposed by Liu and Carter (2000) for describing the differential void ratio at the same stress between natural and reconstituted clays. The mechanism of compressibility of reconstituted clays, when the stress level is larger than the remolded yield stress, is also discussed.