A discus-hulled wave measuring buoy

Described herein is a self-contained, discus-hulled buoy 1.5 m dia., weighing 150 kg, which uses inertial instruments to measure wave height and tilt. Wave tank calibration and the theory of shallow draft buoys demonstrate such a hull accurately follows waves with length greater than twice the buoy diameter. The non-linear response of the buoy determines its sensitivity to low-frequency waves in a sea. And the ratio of wave signal to instrument “noise” is constant over the energetic part of the ocean-wave spectrum for measurements of wave acceleration and slope.     

近海遥测波浪仪的数据采集与处理

为了解决HBF1-1型近海遥测波浪仪的原始数据保留方式与数据处理能力,本文提出了以IBM/PC微机代替原系统单板机的方法,并设计了“ADL”与“SPE”数据采集与处理程序,经与ENDECO 956浮标观测资料的比较以及1a的海上观测应用,证明该方法所获得的资料是可靠的。     

Rocking buoy wave energy converter

A device for converting ocean wave energy into electricity utilizing a rocking buoy and a hydrogen pressure cell is described. The moored buoy contains a pneumatic tube filled with a dense liquid which rocks back and forth as a result of the ocean wave activity. Hydrogen gas, maintained above the dense fluid is alternatively compressed and expanded by the moving fluid. The hydrogen gas communicates with a hydrogen pressure cell and the resulting pressure difference across the cell leads to an electrical voltage and under load, to electrical power.     

A single point mooring spar buoy for measuring ocean waves

We made and set a spar buoy in September 1975 at Tsuyazaki for the purpose of developing the buoy system to acquire the oceanographical data. Motions of the buoy were also measured in terms of three components of acceleration, roll, and pitch. The buoy was removed from the site in May 1978.A method of eliminating influence of the buoy motion on the measured wave data was invented and examined by using the field data. It was found that the influence of the buoy motion on the wave data was so small that the amount of correcting the motion was negligible. In addition wave data obtained at the buoy were compared with those obtained at the fixed type platform, which was built in 1974 to get the reference data of wind, waves and currents. The agreement was found to be good. The performance of the buoy was as good as intended. Thus, it was shown that the buoy so far developed could be used as the platform for oceanographic research such as measuring wind and waves with higher precision.     

The Wavescan second generation directional wave buoy

The authors describe Wavescan, a multipurpose data buoy specially designed for directional wave measurements and meteorological data collection. Their objective was to produce a second-generation high-capability metocean data buoy, with full in situ processing, real-time telemetry, and onshore result presentation. Emphasis is on the design of a buoy hull with the wave-following capability needed to accurately measure wave slope while at the same time retaining the stability to operate and collect meteorological data under the extreme conditions the buoy is likely to meet. The authors briefly review the advantages and disadvantages of the various buoy hulls that have been employed for collection of metocean data. The stability and dynamic response of the final design are then discussed, and results from a field test intercomparison during which a prototype buoy was deployed for several weeks off the mid-Norway shore are examined. The Wavescan system functions and the directional wave analysis are summarized. It is concluded that Wavescan has reached its design goals     

一种利用浮标站资料改进海浪模式有效波高预报的方法

基于浮标站海浪历史数据,利用回归分析方法建立了海浪数值模式有效波高预报产品的一元二次回归方程订正统计模型。通过2017年7月1日-2018年10月10日期间业务试运行结果发现:订正方程能有效改善有效波高数值预报产品的预报精度,且预报时效越短订正效果越显著。其中,第6~11 h预报时效内的订正前后平均绝对误差值减小0.17~0. 241 m,第6~18 h预报时效内订正前后均方根误差减小幅度为0.103~0. 28 m。这说明应用订正统计模型对海浪模式输出产品进行订正,也是改进海浪模式预报准确率的一种有效途径。     

Performance of the CCIW wave direction buoy at ARSLOE

The performance at the Atlantic Remote Sensing Land Ocean Experiment (ARSLOE) of the Canada Centre for Inland Waters (CCIW) wave direction buoy is examined. The waveheight and period data show good agreement with data from neighboring buoys. Nondimensional energy and fetch for wind sea cases agree well with data collected from fixed sensors in Lake Ontario. Direction measurements for a particularly well-defined swell agree well with the Experimental Environmental Research Buoy (XERB) measurements. Meteorological data are compared with that collected at the XERB. Windspeed estimates are reasonably well-correlated and much of the scatter is due to the 24-kin separation between the buoys. There is some systematic bias in the wind direction estimates.     

平台基有缆潜标实时内波监测系统

研究开发了一套依托于海洋平台进行安装的有缆潜标实时内波监测系统.该系统由温度传感器、温盐深传感器(CTD)、定点海流计(DVS)、终端接收机、绞车、钢缆、电缆及锚定重块等组成.温度传感器、CTD和DVS依一定的空间间隔串行连接并固定在系泊钢缆上.系统利用电缆实时供电、采用可寻址RS485总线进行控制和数据传输.集成的有缆潜标内波监测系统在中海油所属的PY30-1平台上进行了现场内波观测,成功捕获了多个内波过程,为获取长时间序列的内波实测数据、进而为开展南海内波机理和工程应用研究提供了有效的技术手段.     

Directional wave spectra measured with a cloverleaf buoy during ARSLOE

The cloverleaf buoy is designed to determine the directional wave spectra with high directional resolution by measuring the vertical acceleration, surface slope, and curvature of the ocean wave surface. This paper describes the properties of the directional wave spectra measured with the cloverleaf buoy during the Atlantic Remote Sensing Land Ocean Experiment (ARSLOE). It is shown that the directional wave spectra measured under relatively constant wind agree fairly well with the similarity spectrum reported previously, but some differences are found in the spectral parameters. The differences in the scale parameters are attributed to unstable atmospheric conditions, though reasonable explanations for those in the shape parameters are difficult now.     

Ocean wave energy harvesting with a piezoelectric coupled buoy structure

An expedient piezoelectric coupled buoy energy harvester from ocean waves is developed. The harvester is made of several piezoelectric coupled cantilevers attached to a floating buoy structure, which can be easily suspended in the intermediate and deep ocean for energy harvesting. In the buoy structure, a slender cylindrical floater is attached on a large sinker. The energy harvesting process is realized by converting the transverse ocean wave energy to the electrical energy via the piezoelectric patches mounted on the cantilevers fixed on the buoy. A smart design of the buoy structure is developed to increase the energy harvesting efficiency by investigation of the effects of the sizes of the floater and the sinker. A numerical model is presented to calculate the generated electric power from buoy energy harvester. The research findings show that up to 24 W electric power can be generated by the proposed expedient buoy harvester with the length of the piezoelectric cantilevers of 1 m and the length of the buoy of 20 m. The technique proposed in this research can provide an expedient, feasible and stable energy supply from the floating buoy structure.     

Theoretical analysis on the transverse motion of a buoy by surface wave

The theoretical analysis on the transverse motion of a buoy is reported here. The analysis has been done by linear differential equation, and its conclusion shows that the transverse motion occurs when the parameters of surface wave and buoy system are related by Mathieu's instability condition. This analysis can be applied to the pole structure which has the equal flexibility in all directions.     

Measurement of wind waves by means of a buoy accelerometer wave gauge

An accelerometer buoy wave gauge developed in the Marine Hydrophysical Institute of the Ukrainian Academy of Sciences is described. This allows measurement of acceleration and the sea surface elevation in the system of reference connected with a buoy. The integral and frequency spectral characteristics of waves can be computed from the records of the wave gauge signal. The use of a buoy accelerometer at sea provides a possibility to derive effective information on the wind waves.Translated by Mikhail M. Trufanov.     

Nearshore directional wave measurements by surface-following buoy and acoustic Doppler current profiler

Directional energy spectra of nearshore surface waves were measured for a 3-year period (2004–2007) at a site with mean depth 14 m and mean tidal range 2.1 m. Triaxys surface-following wave buoys reported hourly directional wave energy spectra and wave parameters near the offshore end of the Savannah River Entrance Channel, Georgia, USA. An acoustic Doppler current profiler (ADCP) was located beside the wave buoy for 3 months. Directional and non-directional surface wave energy spectra and the corresponding bulk wave parameters (height, period, and direction) are compared for the two systems. Most parameters derived from the spectra agree closely; the most significant differences were found at the upper and lower frequency measurement limits, where signal-to-noise ratios were lower. The wave buoy consistently reports a small amount of energy below 0.05 Hz that does not appear in the ADCP-derived spectra and does not appear to be related to the mooring system. This leads to larger mean and peak periods reported by the buoy. All directional spectra were computed using the Maximum Entropy Method for both instruments, but the buoy, with spectra derived from six independent time series, provides lower directional resolving power than the ADCP, which utilizes twelve time series. Both systems gave similar results defining mean and peak wave directions, with the primary difference being that the ADCP indicates energy to be more tightly concentrated around the peak direction.     

Theory and application of calibration techniques for an NDBC directional wave measurements buoy

The National Data Buoy Center (NDBC) of the National Oceanic and Atmospheric Administration (NOAA) deployed a 10-m-diameter discus-type hull in the Pacific Ocean some 185 km southwest of Los Angeles, California, in April 1984. Aboard this hull was an electronic system capable of acquiring, processing, and transmitting to shore directional wave measurements. For this system to produce accurate data, a number of factors had to be taken into account. These factors included noise, amplitude and phase alterations due to mechanical and electrical components, and magnetic fields arising from the hull. Comprehensive calibration and verification techniques were developed and applied to ensure data quality. The system configuration is described with emphasis on the methods used in the data processing to correct for the various factors. Examples of the resulting corrected data are given.     

GPS浮标数据反演海浪谱的理论仿真与试验验证

GPS浮标作为一种新型的海洋测量设备,近年来在海面高度现场测量和星载高度计定标方面取得了重要应用。通过仿真试验对反演海浪谱的方法和流程进行研究,旨在探索从GPS浮标测量的海面高度序列中提取海浪谱的方法。首先,使用Longuest模型生成了海浪波面位移时间序列,并通过Pierson-Moscowitz风浪谱对波面位移的统计特性进行约束,其随机性由相位引入。结合典型潮汐和GPS浮标仪器噪声的仿真时间序列,合成了仿真时间长度1h的1Hz(每秒1次)随机海面高度序列。然后,利用自相关函数法,进行高通滤波和数据压缩,得到了仿真的海浪谱。该仿真结果和理论海浪谱非常接近,可满足海浪谱反演的需求。最后,通过山东石岛外海的GPS浮标现场试验,验证了本文提出的反演方法的适用性。本文的研究解决了GPS浮标反演海浪谱的关键问题,丰富了海浪谱反演的手段,拓展了GPS浮标的应用领域,有望为未来我国的星载波谱仪定标服务。     

A study of spar buoy floating breakwater

A floating breakwater produces less environmental impact, but is easily destroyed by large waves. In this paper, the spar buoy floating breakwater is introduced with a study on the wave reflection and transmission characteristics and mooring line tension induced by the waves. Mei (The Applied Dynamics of Ocean Surface Waves, Wiley, New York (1983) 740 p) proposed a theoretical solution for the reflection and transmission coefficients as the wave propagates through a one-layer slotted barrier. For a multiple-layer fence system, the analytical solution is proposed linearly. The results show that the theoretical computations agree well with the experimental trends. For a multiple-layer fence system, the transmission coefficients become maximal as the layer spacing to wavelength ratio moves to 1/2. Conversely, the coefficients become minimal, as the ratio moves to 0.3. To estimate the maximum tension of the mooring line, both numerical calculations and laboratory experiments were executed. The numerical calculation results were similar to the experimental results.     

Quality evaluation and calibration of the SWIM significant wave height product with buoy data

The significant wave height (SWH) is one of the main parameters that describe wave characteristics and is widely used in wave research fields. Wave parameters measured by radar are influenced by the offshore distance and sea state. Validation and calibration are of great significance for radar data applications. The nadir beam of surface wave investigation and monitoring (SWIM) detects the global-ocean-surface SWH. To determine the product quality of SWIM SWH, this paper carried out time-space matching between SWIM and buoy data. The data qualities were evaluated under different offshore distances and sea states. An improved calibration method was proposed based on sea state segmentation, which considered the distribution of the point collocation numbers in various sea states. The results indicate that (1) the SWIM SWH accuracy at offshore distances greater than 50 km is higher than that at distances less than 50 km, with an root mean squared error (RMSE) of 0.244 4 m, scatter index (SI) of 0.115 6 and relative error (RE) of 9.97% at distances greater than 50 km and those of 0.446 0 m, 0.223 0 and 18.66% at distances less than 50 km. (2) SWIM SWH qualities are better in moderate and rough sea states with RMSEs of 0.284 8 m and 0.316 9 m but are worse in slight and very rough sea states. (3) The effect of the improved calibration method is superior to the traditional method in each sea state and overall data, and the RMSE of SWIM SWH is reduced from the raw 0.313 5 m to 0.285 9 m by the traditional method and 0.198 2 m by the improved method. The influence of spatiotemporal window selection on data quality evaluation was analyzed in this paper. This paper provides references for SWIM SWH product applications.     

基于漂流浮标的南大洋卫星高度计有效波高研究

随着技术的进步和数据处理方法的完善,经过修正的卫星高度计数据已获得普遍认可.但在南大洋缺少波浪现场数据,卫星高度计在极端恶劣气候条件下获得数据的准确度仍受到一定程度的质疑.中国于2020年第36次南极考察中,在南大洋布放了一套感应耦合漂流浮标,可提供可靠的南大洋现场波浪数据.本文利用该漂流浮标2020年1月27日至9月...