Calibration for the shear strain of 3-component borehole strainmeters in eastern Taiwan through Earth and ocean tidal waveform modeling

We propose an approach for calibrating the horizontal tidal shear components [(differential extension (\(\gamma _1\)) and engineering shear (\(\gamma _2\))] of two Sacks–Evertson (in Pap Meteorol Geophys 22:195–208, 1971) SES-3 borehole strainmeters installed in the Longitudinal Valley in eastern Taiwan. The method is based on the waveform reconstruction of the Earth and ocean tidal shear signals through linear regressions on strain gauge signals, with variable sensor azimuth. This method allows us to derive the orientation of the sensor without any initial constraints and to calibrate the shear strain components \(\gamma _1\) and \(\gamma _2\) against \(M_2\) tidal constituent. The results illustrate the potential of tensor strainmeters for recording horizontal tidal shear strain.     

A first modeling of dynamic and static crustal strain field from near-field dilatation measurements: example of the 2013 $$M_w$$ 6.2 Ruisui earthquake,Taiwan

We analyze the high-resolution dilatation data for the October 2013 \(M_w\) 6.2 Ruisui, Taiwan, earthquake, which occurred at a distance of 15–20 km away from a Sacks–Evertson dilatometer network. Based on well-constrained source parameters (\(\hbox {strike}=217^\circ \), \(\hbox {dip}=48^\circ \), \(\hbox {rake}=49^\circ \)), we propose a simple rupture model that explains the permanent static deformation and the dynamic vibrations at short period (\(\sim \)3.5–4.5 s) for most of the four sites with less than 20 % of discrepancies. This study represents a first attempt of modeling simultaneously the dynamic and static crustal strain using dilatation data. The results illustrate the potential for strain recordings of high-frequency seismic waves in the near-field of an earthquake to add constraints on the properties of seismic sources.     

Contribution of solar radiation and geomagnetic activity to global structure of 27-day variation of ionosphere

Twenty-seven-day variation caused by solar rotation is one of the main periodic effects of solar radiation influence on the ionosphere, and there have been many studies on this periodicity using peak electron density \(\mathrm{N_{m}F_{2}}\) and solar radio flux index F10.7. In this paper, the global electron content (GEC) and observation of Solar EUV Monitor (SEM) represent the whole ionosphere and solar EUV flux, respectively, to investigate the 27-day variation. The 27-day period components of indices \((\hbox {GEC}_{27}\), \(\hbox {SEM}_{27}\), \(\hbox {F10.7}_{27}\), \(\hbox {Ap}_{27})\) are obtained using Chebyshev band-pass filter. The comparison of regression results indicates that the index SEM has higher coherence than F10.7 with 27-day variation of the ionosphere. The regression coefficients of \(\hbox {SEM}_{27 }\) varied from 0.6 to 1.4 and the coefficients of \(\hbox {Ap}_{27}\) varied from \({-}\)0.6 to 0.3, which suggests that EUV radiation seasonal variations are the primary driver for the 27-day variations of the ionosphere for most periods. TEC map grid points on three meridians where IGS stations are dense are selected for regression, and the results show that the contribution of solar EUV radiation is positive at all geomagnetic latitudes and larger than geomagnetic activity in most latitudes. The contribution of geomagnetic activity is negative at high geomagnetic latitude, increasing with decreasing geomagnetic latitudes, and positive at low geomagnetic latitudes. The global structure of 27-day variation of ionosphere is presented and demonstrates that there are two zonal anomaly regions along with the geomagnetic latitudes lines and two peaks in the north of Southeast Asia and the Middle Pacific where \(\hbox {TEC}_{27}\) magnitude values are notably larger than elsewhere along zonal anomaly regions.     

The unexpected signal in GRACE estimates of $$C_{20}$$

For science applications of the gravity recovery and climate experiment (GRACE) monthly solutions, the GRACE estimates of \(C_{20}\) (or \(J_{2}\)) are typically replaced by the value determined from satellite laser ranging (SLR) due to an unexpectedly strong, clearly non-geophysical, variation at a period of \(\sim \)160 days. This signal has sometimes been referred to as a tide-like variation since the period is close to the perturbation period on the GRACE orbits due to the spherical harmonic coefficient pair \(C_{22}/S_{22}\) of S2 ocean tide. Errors in the S2 tide model used in GRACE data processing could produce a significant perturbation to the GRACE orbits, but it cannot contribute to the \(\sim \)160-day signal appearing in \(C_{20}\). Since the dominant contribution to the GRACE estimate of \(C_{20}\) is from the global positioning system tracking data, a time series of 138 monthly solutions up to degree and order 10 (\(10\times 10\)) were derived along with estimates of ocean tide parameters up to degree 6 for eight major tides. The results show that the \(\sim \)160-day signal remains in the \(C_{20}\) time series. Consequently, the anomalous signal in GRACE \(C_{20}\) cannot be attributed to aliasing from the errors in the S2 tide. A preliminary analysis of the cross-track forces acting on GRACE and the cross-track component of the accelerometer data suggests that a temperature-dependent systematic error in the accelerometer data could be a cause. Because a wide variety of science applications relies on the replacement values for \(C_{20}\), it is essential that the SLR estimates are as reliable as possible. An ongoing concern has been the influence of higher degree even zonal terms on the SLR estimates of \(C_{20}\), since only \(C_{20}\) and \(C_{40}\) are currently estimated. To investigate whether a better separation between \(C_{20}\) and the higher-degree terms could be achieved, several combinations of additional SLR satellites were investigated. In addition, a series of monthly gravity field solutions (\(60\times 60\)) were estimated from a combination of GRACE and SLR data. The results indicate that the combination of GRACE and SLR data might benefit the resonant orders in the GRACE-derived gravity fields, but it appears to degrade the recovery of the \(C_{20}\) variations. In fact, the results suggest that the poorer recovery of \(C_{40}\) by GRACE, where the annual variation is significantly underestimated, may be affecting the estimates of \(C_{20}\). Consequently, it appears appropriate to continue using the SLR-based estimates of \(C_{20}\), and possibly also \(C_{40}\), to augment the existing GRACE mission.     

Seasonal low-degree changes in terrestrial water mass load from global GNSS measurements

Large-scale mass redistribution in the terrestrial water storage (TWS) leads to changes in the low-degree spherical harmonic coefficients of the Earth’s surface mass density field. Studying these low-degree fluctuations is an important task that contributes to our understanding of continental hydrology. In this study, we use global GNSS measurements of vertical and horizontal crustal displacements that we correct for atmospheric and oceanic effects, and use a set of modified basis functions similar to Clarke et al. (Geophys J Int 171:1–10, 2007) to perform an inversion of the corrected measurements in order to recover changes in the coefficients of degree-0 (hydrological mass change), degree-1 (centre of mass shift) and degree-2 (flattening of the Earth) caused by variations in the TWS over the period January 2003–January 2015. We infer from the GNSS-derived degree-0 estimate an annual variation in total continental water mass with an amplitude of \((3.49 \pm 0.19) \times 10^{3}\) Gt and a phase of \(70^{\circ } \pm 3^{\circ }\) (implying a peak in early March), in excellent agreement with corresponding values derived from the Global Land Data Assimilation System (GLDAS) water storage model that amount to \((3.39 \pm 0.10) \times 10^{3}\) Gt and \(71^{\circ } \pm 2^{\circ }\), respectively. The degree-1 coefficients we recover from GNSS predict annual geocentre motion (i.e. the offset change between the centre of common mass and the centre of figure) caused by changes in TWS with amplitudes of \(0.69 \pm 0.07\) mm for GX, \(1.31 \pm 0.08\) mm for GY and \(2.60 \pm 0.13\) mm for GZ. These values agree with GLDAS and estimates obtained from the combination of GRACE and the output of an ocean model using the approach of Swenson et al. (J Geophys Res 113(B8), 2008) at the level of about 0.5, 0.3 and 0.9 mm for GX, GY and GZ, respectively. Corresponding degree-1 coefficients from SLR, however, generally show higher variability and predict larger amplitudes for GX and GZ. The results we obtain for the degree-2 coefficients from GNSS are slightly mixed, and the level of agreement with the other sources heavily depends on the individual coefficient being investigated. The best agreement is observed for \(T_{20}^C\) and \(T_{22}^S\), which contain the most prominent annual signals among the degree-2 coefficients, with amplitudes amounting to \((5.47 \pm 0.44) \times 10^{-3}\) and \((4.52 \pm 0.31) \times 10^{-3}\) m of equivalent water height (EWH), respectively, as inferred from GNSS. Corresponding agreement with values from SLR and GRACE is at the level of or better than \(0.4 \times 10^{-3}\) and \(0.9 \times 10^{-3}\) m of EWH for \(T_{20}^C\) and \(T_{22}^S\), respectively, while for both coefficients, GLDAS predicts smaller amplitudes. Somewhat lower agreement is obtained for the order-1 coefficients, \(T_{21}^C\) and \(T_{21}^S\), while our GNSS inversion seems unable to reliably recover \(T_{22}^C\). For all the coefficients we consider, the GNSS-derived estimates from the modified inversion approach are more consistent with the solutions from the other sources than corresponding estimates obtained from an unconstrained standard inversion.     

Impact of the VLBA on reference frames and earth orientation studies

The geodetic VLBI community began using VLBA antennas in 1989 for geodesy and astrometry. We examine how usage of the VLBA has improved the celestial reference frame, the terrestrial reference frame, and Earth orientation parameters. Without the VLBA, ICRF2 would have had only 1011 sources instead of 3414. ICRF3 will contain at least 4121 sources, with approximately 70 % or more coming exclusively from VLBA astrometry and geodesy sessions. The terrestrial reference frame is also more stable and precise due to VLBA geodesy sessions. Approximately two dozen geodesy stations that have participated in VLBA sessions show average position formal errors that are \(\sim \)13–14 % better in the horizontal components and \(\sim \)5 % better in the vertical component than would be expected solely from the increased number of observations. Also the Earth orientation parameters obtained from the RDV sessions represent the most accurate EOP series of any of the long-term VLBI session types.     

Adding source positions to the IVS combination—First results

The consistent estimation of terrestrial reference frames (TRF), celestial reference frames (CRF) and Earth orientation parameters (EOP) is still an open subject and offers a large field of investigations. Until now, source positions resulting from Very Long Baseline Interferometry (VLBI) observations are not routinely combined on the level of normal equations in the same way as it is a common process for station coordinates and EOPs. The combination of source positions based on VLBI observations is now integrated in the IVS combination process. We present the studies carried out to evaluate the benefit of the combination compared to individual solutions. On the level of source time series, improved statistics regarding weighted root mean square have been found for the combination in comparison with the individual contributions. In total, 67 stations and 907 sources (including 291 ICRF2 defining sources) are included in the consistently generated CRF and TRF covering 30 years of VLBI contributions. The rotation angles \(A_1\), \(A_2\) and \(A_3\) relative to ICRF2 are ?12.7, 51.7 and 1.8 \({\upmu }\) as, the drifts \(D_\alpha \) and \(D_\delta \) are ?67.2 and 19.1 \(\upmu \) as/rad and the bias \(B_\delta \) is 26.1 \(\upmu \) as. The comparison of the TRF solution with the IVS routinely combined quarterly TRF solution shows no significant impact on the TRF, when the CRF is estimated consistently with the TRF. The root mean square value of the post-fit station coordinate residuals is 0.9 cm.     

Precise and efficient evaluation of gravimetric quantities at arbitrarily scattered points in space

Gravimetric quantities are commonly represented in terms of high degree surface or solid spherical harmonics. After EGM2008, such expansions routinely extend to spherical harmonic degree 2190, which makes the computation of gravimetric quantities at a large number of arbitrarily scattered points in space using harmonic synthesis, a very computationally demanding process. We present here the development of an algorithm and its associated software for the efficient and precise evaluation of gravimetric quantities, represented in high degree solid spherical harmonics, at arbitrarily scattered points in the space exterior to the surface of the Earth. The new algorithm is based on representation of the quantities of interest in solid ellipsoidal harmonics and application of the tensor product trigonometric needlets. A FORTRAN implementation of this algorithm has been developed and extensively tested. The capabilities of the code are demonstrated using as examples the disturbing potential T, height anomaly \(\zeta \), gravity anomaly \(\Delta g\), gravity disturbance \(\delta g\), north–south deflection of the vertical \(\xi \), east–west deflection of the vertical \(\eta \), and the second radial derivative \(T_{rr}\) of the disturbing potential. After a pre-computational step that takes between 1 and 2 h per quantity, the current version of the software is capable of computing on a standard PC each of these quantities in the range from the surface of the Earth up to 544 km above that surface at speeds between 20,000 and 40,000 point evaluations per second, depending on the gravimetric quantity being evaluated, while the relative error does not exceed \(10^{-6}\) and the memory (RAM) use is 9.3 GB.     

Performance evaluation of GNSS-TEC estimation techniques at the grid point in middle and low latitudes during different geomagnetic conditions

Global Navigation Satellite Systems (GNSS) have become a powerful tool use in surveying and mapping, air and maritime navigation, ionospheric/space weather research and other applications. However, in some cases, its maximum efficiency could not be attained due to some uncorrelated errors associated with the system measurements, which is caused mainly by the dispersive nature of the ionosphere. Ionosphere has been represented using the total number of electrons along the signal path at a particular height known as Total Electron Content (TEC). However, there are many methods to estimate TEC but the outputs are not uniform, which could be due to the peculiarity in characterizing the biases inside the observables (measurements), and sometimes could be associated to the influence of mapping function. The errors in TEC estimation could lead to wrong conclusion and this could be more critical in case of safety-of-life application. This work investigated the performance of Ciraolo’s and Gopi’s GNSS-TEC calibration techniques, during 5 geomagnetic quiet and disturbed conditions in the month of October 2013, at the grid points located in low and middle latitudes. The data used are obtained from the GNSS ground-based receivers located at Borriana in Spain (40\(^{\circ }\)N, 0\(^{\circ }\)E; mid latitude) and Accra in Ghana (5.50\(^{\circ }\)N, ?0.20\(^{\circ }\)E; low latitude). The results of the calibrated TEC are compared with the TEC obtained from European Geostationary Navigation Overlay System Processing Set (EGNOS PS) TEC algorithm, which is considered as a reference data. The TEC derived from Global Ionospheric Maps (GIM) through International GNSS service (IGS) was also examined at the same grid points. The results obtained in this work showed that Ciraolo’s calibration technique (a calibration technique based on carrier-phase measurements only) estimates TEC better at middle latitude in comparison to Gopi’s technique (a calibration technique based on code and carrier-phase measurements). At the same time, Gopi’s calibration was also found more reliable in low latitude than Ciraolo’s technique. In addition, the TEC derived from IGS GIM seems to be much reliable in middle-latitude than in low-latitude region.     

Solution to the spectral filter problem of residual terrain modelling (RTM)

In physical geodesy, the residual terrain modelling (RTM) technique is frequently used for high-frequency gravity forward modelling. In the RTM technique, a detailed elevation model is high-pass-filtered in the topography domain, which is not equivalent to filtering in the gravity domain. This in-equivalence, denoted as spectral filter problem of the RTM technique, gives rise to two imperfections (errors). The first imperfection is unwanted low-frequency (LF) gravity signals, and the second imperfection is missing high-frequency (HF) signals in the forward-modelled RTM gravity signal. This paper presents new solutions to the RTM spectral filter problem. Our solutions are based on explicit modelling of the two imperfections via corrections. The HF correction is computed using spectral domain gravity forward modelling that delivers the HF gravity signal generated by the long-wavelength RTM reference topography. The LF correction is obtained from pre-computed global RTM gravity grids that are low-pass-filtered using surface or solid spherical harmonics. A numerical case study reveals maximum absolute signal strengths of \(\sim 44\) mGal (0.5 mGal RMS) for the HF correction and \(\sim 33\) mGal (0.6 mGal RMS) for the LF correction w.r.t. a degree-2160 reference topography within the data coverage of the SRTM topography model (\(56^{\circ }\hbox {S} \le \phi \le 60^{\circ }\hbox {N}\)). Application of the LF and HF corrections to pre-computed global gravity models (here the GGMplus gravity maps) demonstrates the efficiency of the new corrections over topographically rugged terrain. Over Switzerland, consideration of the HF and LF corrections reduced the RMS of the residuals between GGMplus and ground-truth gravity from 4.41 to 3.27 mGal, which translates into \(\sim 26\)% improvement. Over a second test area (Canada), our corrections reduced the RMS of the residuals between GGMplus and ground-truth gravity from 5.65 to 5.30 mGal (\(\sim 6\)% improvement). Particularly over Switzerland, geophysical signals (associated, e.g. with valley fillings) were found to stand out more clearly in the RTM-reduced gravity measurements when the HF and LF correction are taken into account. In summary, the new RTM filter corrections can be easily computed and applied to improve the spectral filter characteristics of the popular RTM approach. Benefits are expected, e.g. in the context of the development of future ultra-high-resolution global gravity models, smoothing of observed gravity data in mountainous terrain and geophysical interpretations of RTM-reduced gravity measurements.     

Joint analysis of celestial pole offset and free core nutation series

Three combined celestial pole offset (CPO) series computed at the Paris Observatory (C04), the United States Naval Observatory (USNO), and the International VLBI Service for Geodesy and Astrometry (IVS), as well as six free core nutation (FCN) models, were compared from different perspectives, such as stochastic and systematic differences, and FCN amplitude and phase variations. The differences between the C04 and IVS CPO series were mostly stochastic, whereas a low-frequency bias at the level of several tens of \(\upmu \)as was found between the C04 and USNO CPO series. The stochastic differences between the C04 and USNO series became considerably smaller when computed at the IVS epochs, which can indicate possible problems with the interpolation of the IVS data at the midnight epochs during the computation of the C04 and USNO series. The comparison of the FCN series showed that the series computed with similar window widths of 1.1–1.2 years were close to one another at a level of 10–20 \(\upmu \)as, whereas the differences between these series and the series computed with a larger window width of 4 and 7 years reached 100 \(\upmu \)as. The dependence of the FCN model on the underlying CPO series was investigated. The RMS differences between the FCN models derived from the C04, USNO, and IVS CPO series were at a level of approximately 15 \(\upmu \)as, which was considerably smaller than the differences among the CPO series. The analysis of the differences between the IVS, C04, and USNO CPO series suggested that the IVS series would be preferable for both precession-nutation and FCN-related studies.     

On the consistency of the current conventional EOP series and the celestial and terrestrial reference frames

Precise transformation between the celestial reference frames (CRF) and terrestrial reference frames (TRF) is needed for many purposes in Earth and space sciences. According to the Global Geodetic Observing System (GGOS) recommendations, the accuracy of positions and stability of reference frames should reach 1 mm and 0.1 mm year\(^{-1}\), and thus, the Earth Orientation Parameters (EOP) should be estimated with similar accuracy. Different realizations of TRFs, based on the combination of solutions from four different space geodetic techniques, and CRFs, based on a single technique only (VLBI, Very Long Baseline Interferometry), might cause a slow degradation of the consistency among EOP, CRFs, and TRFs (e.g., because of differences in geometry, orientation and scale) and a misalignment of the current conventional EOP series, IERS 08 C04. We empirically assess the consistency among the conventional reference frames and EOP by analyzing the record of VLBI sessions since 1990 with varied settings to reflect the impact of changing frames or other processing strategies on the EOP estimates. Our tests show that the EOP estimates are insensitive to CRF changes, but sensitive to TRF variations and unmodeled geophysical signals at the GGOS level. The differences between the conventional IERS 08 C04 and other EOP series computed with distinct TRF settings exhibit biases and even non-negligible trends in the cases where no differential rotations should appear, e.g., a drift of about 20 \(\upmu \)as year\(^{-1 }\)in \(y_{\mathrm{pol }}\) when the VLBI-only frame VTRF2008 is used. Likewise, different strategies on station position modeling originate scatters larger than 150 \(\upmu \)as in the terrestrial pole coordinates.     

基于地基GPS研究台风引起电离层TEC的变化特征

利用GPS研究电离层,具有其他探测技术所没有的全天候、高分辨率、大范围等优点.本文采用双频GPS数据提取区域电离层电子浓度总含量（TEC）,并结合全球电离层地理（GIM）数据,借助滑动四分位距法建立TEC背景值.研究了台风“莫兰蒂”对其经过区域及登陆地点电离层TEC的影响.分析表明,台风登陆厦门前一天,厦门地区电离层TEC发生了较强的正扰动,登陆后第二天,TEC发生了小尺度的负扰动;台风临近台湾岛前,东南沿海和台湾岛区域电离层出现了大范围的正异常扰动,其值为15～20 TECU,持续时间10 h.结合厦门和台湾岛的地形,推测此次TEC异常原因是由于台风所激发的声重力波传播到电离层高度,造成了电离层的异常扰动.      

A high-precision digital astrogeodetic traverse in an area of steep geoid gradients close to the coast of Perth,Western Australia

We present results from a new vertical deflection (VD) traverse observed in Perth, Western Australia, which is the first of its kind in the Southern Hemisphere. A digital astrogeodetic QDaedalus instrument was deployed to measure VDs with \({\sim }\)0.2\(''\) precision at 39 benchmarks with a \({{\sim }}1~\hbox {km}\) spacing. For the conversion of VDs to quasigeoid height differences, the method of astronomical–topographical levelling was applied, based on topographical information from the Shuttle Radar Topography Mission. The astronomical quasigeoid heights are in 20–30 mm (RMS) agreement with three independent gravimetric quasigeoid models, and the astrogeodetic VDs agree to 0.2–0.3\(''\) (north–south) and 0.6–0.9\(''\) (east–west) RMS. Tilt-like biases of \({\sim }1\,\,\hbox {mm}\) over \({\sim }1\,\,\hbox {km}\) are present for all quasigeoid models within \({\sim }20\,\,\hbox {km}\) of the coastline, suggesting inconsistencies in the coastal zone gravity data. The VD campaign in Perth was designed as a low-cost effort, possibly allowing replication in other Southern Hemisphere countries (e.g., Asia, Africa, South America and Antarctica), where VD data are particularly scarce.     

The first Australian gravimetric quasigeoid model with location-specific uncertainty estimates

We describe the computation of the first Australian quasigeoid model to include error estimates as a function of location that have been propagated from uncertainties in the EGM2008 global model, land and altimeter-derived gravity anomalies and terrain corrections. The model has been extended to include Australia’s offshore territories and maritime boundaries using newer datasets comprising an additional \({\sim }\)280,000 land gravity observations, a newer altimeter-derived marine gravity anomaly grid, and terrain corrections at \(1^{\prime \prime }\times 1^{\prime \prime }\) resolution. The error propagation uses a remove–restore approach, where the EGM2008 quasigeoid and gravity anomaly error grids are augmented by errors propagated through a modified Stokes integral from the errors in the altimeter gravity anomalies, land gravity observations and terrain corrections. The gravimetric quasigeoid errors (one sigma) are 50–60 mm across most of the Australian landmass, increasing to \({\sim }100\) mm in regions of steep horizontal gravity gradients or the mountains, and are commensurate with external estimates.     

Consistent realization of Celestial and Terrestrial Reference Frames

The Celestial Reference System (CRS) is currently realized only by Very Long Baseline Interferometry (VLBI) because it is the space geodetic technique that enables observations in that frame. In contrast, the Terrestrial Reference System (TRS) is realized by means of the combination of four space geodetic techniques: Global Navigation Satellite System (GNSS), VLBI, Satellite Laser Ranging (SLR), and Doppler Orbitography and Radiopositioning Integrated by Satellite. The Earth orientation parameters (EOP) are the link between the two types of systems, CRS and TRS. The EOP series of the International Earth Rotation and Reference Systems Service were combined of specifically selected series from various analysis centers. Other EOP series were generated by a simultaneous estimation together with the TRF while the CRF was fixed. Those computation approaches entail inherent inconsistencies between TRF, EOP, and CRF, also because the input data sets are different. A combined normal equation (NEQ) system, which consists of all the parameters, i.e., TRF, EOP, and CRF, would overcome such an inconsistency. In this paper, we simultaneously estimate TRF, EOP, and CRF from an inter-technique combined NEQ using the latest GNSS, VLBI, and SLR data (2005–2015). The results show that the selection of local ties is most critical to the TRF. The combination of pole coordinates is beneficial for the CRF, whereas the combination of \(\varDelta \hbox {UT1}\) results in clear rotations of the estimated CRF. However, the standard deviations of the EOP and the CRF improve by the inter-technique combination which indicates the benefits of a common estimation of all parameters. It became evident that the common determination of TRF, EOP, and CRF systematically influences future ICRF computations at the level of several \(\upmu \)as. Moreover, the CRF is influenced by up to \(50~\upmu \)as if the station coordinates and EOP are dominated by the satellite techniques.     

Density interface topography recovered by inversion of satellite gravity gradiometry observations

A radial integration of spherical mass elements (i.e. tesseroids) is presented for evaluating the six components of the second-order gravity gradient (i.e. second derivatives of the Newtonian mass integral for the gravitational potential) created by an uneven spherical topography consisting of juxtaposed vertical prisms. The method uses Legendre polynomial series and takes elastic compensation of the topography by the Earth’s surface into account. The speed of computation of the polynomial series increases logically with the observing altitude from the source of anomaly. Such a forward modelling can be easily applied for reduction of observed gravity gradient anomalies by the effects of any spherical interface of density. An iterative least-squares inversion of measured gravity gradient coefficients is also proposed to estimate a regional set of juxtaposed topographic heights. Several tests of recovery have been made by considering simulated gradients created by idealistic conical and irregular Great Meteor seamount topographies, and for varying satellite altitudes and testing different levels of uncertainty. In the case of gravity gradients measured at a GOCE-type altitude of \(\sim \)300 km, the search converges down to a stable but smooth topography after 10–15 iterations, while the final root-mean-square error is \(\sim \)100 m that represents only 2 % of the seamount amplitude. This recovery error decreases with the altitude of the gravity gradient observations by revealing more topographic details in the region of survey.     

A neural network model for predicting weighted mean temperature

Water vapor is an important element of the Earth’s atmosphere, and most of it concentrates at the bottom of the troposphere. Knowledge of the water vapor measured by Global Navigation Satellite Systems (GNSS) is an important direction of GNSS research. In particular, when the zenith wet delay is converted to precipitable water vapor, the weighted mean temperature \(T_\mathrm{m}\) is a variable parameter to be determined in this conversion. The purpose of the study is getting a more accurate \(T_\mathrm{m}\) model for global users by a combination of two different characteristics of \(T_\mathrm{m}\) (i.e., the \(T_\mathrm{m}\) seasonal variations and the relationships between \(T_\mathrm{m}\) and surface meteorological elements). The modeling process was carried out by using the neural network technology. A multilayer feedforward neural network model (the NN) was established. The NN model is used with measurements of only surface temperature \(T_\mathrm{S}\). The NN was validated and compared with four other published global \(T_\mathrm{m}\) models. The results show that the NN performed better than any of the four compared models on the global scale.     

Contributions to reference systems from Lunar Laser Ranging using the IfE analysis model

Lunar Laser Ranging (LLR) provides various quantities related to reference frames like Earth orientation parameters, coordinates and velocities of ground stations in the Earth-fixed frame and selenocentric coordinates of the lunar retro-reflectors. This paper presents the recent results from LLR data analysis at the Institut für Erdmessung, Leibniz Universität Hannover, based on all LLR data up to the end of 2016. The estimates of long-periodic nutation coefficients with periods between 13.6 days and 18.6 years are obtained with an accuracy in the order of 0.05–0.7 milliarcseconds (mas). Estimations of the Earth rotation phase \(\Delta \)UT are accurate at the level of 0.032 ms if more than 14 normal points per night are included. The tie between the dynamical ephemeris frame to the kinematic celestial frame is estimated from pure LLR observations by two angles and their rates with an accuracy of 0.25 and 0.02 mas per year. The estimated station coordinates and velocities are compared to the ITRF2014 solution and the geometry of the retro-reflector network with the DE430 solution. The given accuracies represent 3 times formal errors of the parameter fit. The accuracy for \(\Delta \)UT is based on the standard deviation of the estimates with respect to the reference C04 solution.     

Evaluation of gravitational curvatures of a tesseroid in spherical integral kernels

Proper understanding of how the Earth’s mass distributions and redistributions influence the Earth’s gravity field-related functionals is crucial for numerous applications in geodesy, geophysics and related geosciences. Calculations of the gravitational curvatures (GC) have been proposed in geodesy in recent years. In view of future satellite missions, the sixth-order developments of the gradients are becoming requisite. In this paper, a set of 3D integral GC formulas of a tesseroid mass body have been provided by spherical integral kernels in the spatial domain. Based on the Taylor series expansion approach, the numerical expressions of the 3D GC formulas are provided up to sixth order. Moreover, numerical experiments demonstrate the correctness of the 3D Taylor series approach for the GC formulas with order as high as sixth order. Analogous to other gravitational effects (e.g., gravitational potential, gravity vector, gravity gradient tensor), numerically it is found that there exist the very-near-area problem and polar singularity problem in the GC east–east–radial, north–north–radial and radial–radial–radial components in spatial domain, and compared to the other gravitational effects, the relative approximation errors of the GC components are larger due to not only the influence of the geocentric distance but also the influence of the latitude. This study shows that the magnitude of each term for the nonzero GC functionals by a grid resolution 15\(^{{\prime } }\,\times \) 15\(^{{\prime }}\) at GOCE satellite height can reach of about 10\(^{-16}\) m\(^{-1}\) s\(^{2}\) for zero order, 10\(^{-24 }\) or 10\(^{-23}\) m\(^{-1}\) s\(^{2}\) for second order, 10\(^{-29}\) m\(^{-1}\) s\(^{2}\) for fourth order and 10\(^{-35}\) or 10\(^{-34}\) m\(^{-1}\) s\(^{2}\) for sixth order, respectively.